MK60DN512VLQ10 - K60 100MHz Cortex-M4 MCU 512KB | NXP
MPN： MK60DN512VLQ10 ✓ 啟用中MK60DN512VLQ10 概覽
A Kinetis K60 microcontroller is a member of the Cortex-M4 microcontroller family - a 32-bit microcontroller (MCU) class designed for deterministic real-time control with DSP extensions and a single-precision floating point unit. Within the broader taxonomy, it sits as MCU -> ARM Cortex-M MCU -> Kinetis K-series -> industrial-connected sub-family, and NXP positions it as a power-management IC companion for industrial gateway, smart energy, and factory automation designs where deterministic networking and on-chip crypto are deciding factors.
Key features include 512 KB flash, 128 KB SRAM, 100 MHz Cortex-M4 with FPU, hardware AES/SHA/Random-Number Generator, USB 2.0 FS OTG, Ethernet 10/100 MAC with IEEE 1588, 16-bit ADC (DSA-aware), 12-bit DAC, multiple timers (FTM, PIT, LPTMR, RTC), and an operating voltage range of 1.71 V to 3.6 V. The 144-LQFP footprint delivers 100 usable GPIO, which is one of the largest in the Kinetis K-series and uniquely suited to multi-peripheral industrial nodes.
Architecturally, the K60DN512 implements a Cortex-M4 core with single-precision FPU, a 16-channel DMA controller, 4 KB instruction cache/scratchpad RAM, and a multi-layer AIPS-Lite bus fabric. The integrated Ethernet MAC with 1588 timestamping offloads the CPU from timing-critical packet processing, while the on-chip RNG and AES/SHA engines accelerate TLS / IPSec handshakes common in connected industrial gateways.
Typical applications include industrial Ethernet gateways, IEC 61850 / smart-grid substation controllers, factory automation PLCs, networked motor drives, USB-connected instrumentation, and HVAC controllers. The wide 1.71 V - 3.6 V supply range simplifies battery-backed and 3.3 V-rail designs without an additional LDO.
When designing with the K60, reserve the upper 32 KB of flash for the IEC 1588-aware Ethernet buffer descriptor table and provision a 25 MHz crystal for the MAC reference clock - the integrated PHY interface does not generate this clock internally. Place a 4.7 uF + 0.1 uF decoupling pair within 5 mm of VDDA for ADC noise floor compliance.
This page synthesizes distributor pricing for the LQFP-144 variant, drop-in alternatives within the Kinetis K10/K20/K60 family, and design notes not consolidated in any single distributor product page.
直接替換替代品，適用於 MK60DN512VLQ10 — 相同封裝，腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
此系列的變體
與下列產品可直接替換的同系列型號： MK60DN512VLQ10 （相同外形與佔位） — 差異在於 Package, ADC, Core Architecture, Program Flash Memory, Operating Temperature Range.
MK60DN512ZVLQ10
✅ 直接替換聯絡詢價
查看資料表 →MK60DN512ZVLQ10R
✅ 直接替換📋 參考替代品（不在目錄中）
MK60FN1M0VLQ12
✅ 直接替換聯絡詢價
查看資料表 →PK60FN1M0VLQ12
✅ 直接替換📋 參考替代品（不在目錄中）
MK10DN512ZAB10R
✅ 直接替換聯絡詢價
查看資料表 →MK50DN512CLQ10
✅ 直接替換聯絡詢價
查看資料表 →MK60DN512VLQ10 最大額定值與電氣特性
| Core Architecture | ARM Cortex-M4 with FPU |
| Core Frequency | 100 MHz |
| 資料匯流排寬度 | 32-bit |
| Program Flash | 512 KB (512K x 8) |
| SRAM | 128 KB |
| 供應電壓 | 1.71 V to 3.6 V |
| 工作溫度 | -40C to +105C |
| 封裝 | 144-LQFP (20 mm x 20 mm) |
| 安裝類型 | Surface Mount |
| I/O Pins | 100 |
| Ethernet | 10/100 MAC with IEEE 1588 |
| USB | USB 2.0 Full-Speed OTG |
| ADC | 16-bit SAR ADC |
| Hardware Crypto | AES, SHA, Random Number Generator |
| DAC | 12-bit |
| DMA Channels | 16 |
| MSL 等級 | 3 (168 Hours) |
| RoHS 狀態 | Compliant |
MK60DN512VLQ10 144-lqfp (20 mm x 20 mm) 腳位配置指南
MK60DN512VLQ10（144-lqfp (20 mm x 20 mm) 封裝）的腳位配置。 此數位 IC 包含 GPIO、通訊介面（UART、SPI、I2C）與電源腳位。替代腳位功能與配置選項請參閱製造商資料表。對嵌入式系統設計與 PCB 佈局至關重要。
無詳細腳位定義資料： MK60DN512VLQ10.
請參閱 資料表 以查看完整腳位配置。
典型應用
MK60DN512VLQ10 適用於 6 應用s: Industrial Ethernet Gateway, Smart Energy / IEC 61850 Substation Controller, Factory Automation PLC, USB-Connected Instrumentation, Building Automation / HVAC Controller, Networked Motor Drive Controller.
Industrial Ethernet Gateway
The MK60DN512VLQ10's on-chip 10/100 Ethernet MAC with hardware IEEE 1588 timestamping and AES/SHA accelerators make it ideal for industrial Ethernet gateways serving EtherCAT, PROFINET, Modbus TCP, or OPC-UA protocols. The 100 MHz Cortex-M4 FPU is fast enough to terminate TCP/TLS sessions on the gateway tier, avoiding an external processor. The 144-LQFP pin-out exposes 100 GPIOs to drive status LEDs, isolated UART lines, and SPI-linked slave PHYs alongside the on-chip MAC. In a typical implementation the Kinetis sits between the RS-485 fieldbus and the Ethernet uplink, framing and signing industrial frames at sub-millisecond latency - the 1588 timestamp engine is the deciding factor for cyclic-data deterministic delivery.
推薦
Smart Energy / IEC 61850 Substation Controller
For IEC 61850 and DLMS/COSEM substation IEDs, the MK60DN512VLQ10 offers 128 KB SRAM for GOOSE message buffering, hardware AES/SHA for IEC 62351 security envelopes, and 512 KB flash sized for the full IEC 61850 stack with room to spare. The -40 C to +105 C industrial temperature grade meets substation environmental specifications, and the 144-LQFP package simplifies through-hole-friendly PCB layouts typical of utility enclosures. In a typical IED design the K60 samples three-phase current/voltage on its 16-bit ADC, packages the values into streamed Ethernet frames via the on-chip MAC, and signs each packet in hardware - consuming approximately 28 KB of flash for the TCP/IP + IEC 61850 stacks and leaving over 400 KB for application logic.
推薦
Factory Automation PLC
For factory automation PLCs and remote I/O nodes, the K60 family brings deterministic EtherCAT/Profinet connectivity, flexible timers (FTM, PIT), and 16-bit ADC plus 12-bit DAC for analog loop control. The 1.71 V - 3.6 V supply range simplifies 24 V-rail-derived 3.3 V designs through a small LDO. Hardware AES is useful for tamper-evident audit logs in regulated industries. In practice the MK60DN512VLQ10 integrates the cycle-time-critical digital I/O scan at 1 kHz while sharing the bus for HMI updates - the 100 MHz Cortex-M4 with FPU executes the entire PID loop in under 15 microseconds, leaving the CPU free to handle EtherCAT Distributed Clock synchronisation.
推薦
USB-Connected Instrumentation
The integrated USB 2.0 Full-Speed OTG controller with charge pump makes the MK60DN512VLQ10 a strong fit for USB-tethered bench instruments - oscilloscope front-ends, data-acquisition modules, and protocol analysers. The 16-bit ADC and on-chip PGAs feed acquisition front-ends directly without external amplification, while the 100 MHz core with FPU executes 4th-order bessel filters in real time. The 144-LQFP exposes 100 GPIOs for front-panel buttons/encoders, LCD interface, and SPI/QSPI connections to external flash or FPGAs. In a typical oscilloscope front-end the Kinetis streams 16-bit ADC samples at 1 MSPS over USB while computing peak-detection on-the-fly.
推薦
Building Automation / HVAC Controller
The MK60DN512VLQ10's Ethernet, USB-OTG, and rich analog front-end make it a single-chip candidate for building-automation controllers driving BACnet, Modbus, and LonWorks networks. The 16-bit ADC plus 12-bit DAC handle thermistor biasing, current-loop 4-20 mA outputs, and 0-10 V lighting control without external signal conditioning. Its low-power modes (LLS, VLLS) suit battery-backed real-time-clock sub-systems. Power dissipation on a continuous Ethernet-attached BACnet node averages around 0.4 W - substantially less than a Linux-class SBC the K60DN512 can replace cost-wise.
推薦
Networked Motor Drive Controller
The MK60DN512VLQ10 is suited as the supervisory MCU in networked motor-drive and pump-controller applications, combining Ethernet-based fieldbus communication with high-resolution timer support for SVPWM. The 144-LQFP pin count lets the K60 interface directly to PFC IGBT gate drives, shunt-sense ADCs, and resolver excitation hardware without an external bus expander. In a 3-phase PMSM drive the Cortex-M4 with FPU executes a sensorless FOC loop at 16 kHz with 4 microseconds CPU headroom - sufficient margin for the on-chip Ethernet MAC to maintain PROFINET IRT cycle times without jitter.
推薦
推薦產品摘要
工程參考資料，適用於 MK60DN512VLQ10 — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | MK60DN512ZVLQ10 | MK60DN512ZVLQ10R | MK60FN1M0VLQ12 | PK60FN1M0VLQ12 | MK10DN512ZAB10R | MK50DN512CLQ10 |
|---|---|---|---|---|---|---|---|
| Package | 144-LQFP (20x20) | 144-LQFP (20x20) - identical | 144-LQFP (20x20) - identical | 144-LQFP (20x20) - identical | 144-LQFP (20x20) - identical | 144-LQFP (20x20) - identical | 144-LQFP (20x20) - identical |
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Core Architecture | ARM Cortex-M4 with FPU | ARM Cortex-M4 with FPU | ARM Cortex-M4 with FPU | ARM Cortex-M4 with FPU | ARM Cortex-M4 with FPU | ARM Cortex-M4 with FPU | ARM Cortex-M4 with FPU |
| Core Frequency | 100 MHz | 100 MHz | 120 MHz | 120 MHz | 100 MHz | 50 MHz | |
| Program Flash | 512 KB | 512 KB | 1 MB | 1 MB | 512 KB | 512 KB | |
| SRAM | 128 KB | 128 KB | 128 KB | 128 KB | 128 KB | 128 KB | |
| Ethernet | 10/100 MAC with IEEE 1588 | 10/100 MAC with IEEE 1588 | 10/100 MAC with IEEE 1588 | 10/100 MAC with IEEE 1588 | None | None | |
| USB | USB 2.0 FS OTG | USB 2.0 FS OTG | USB 2.0 FS OTG | USB 2.0 FS OTG | USB 2.0 FS OTG | USB 2.0 FS OTG (MK50DN512CLQ10 peripheral count) | |
| Hardware Crypto | AES / SHA / RNG | AES / SHA / RNG | AES / SHA / RNG / Tamper | AES / SHA / RNG / Tamper (Secure variants) | Limited RNG only | AES / SHA / RNG | |
| Operating Temperature | -40C to +105C | -40C to +105C | -40C to +105C | -40C to +105C | -40C to +105C | -40C to +85C |
主要差異化特點
- Hardware IEEE 1588 timestamping on Ethernet MAC for sub-100 ns distributed clock synchronisation (對比MK10DN512ZVLQ10)
- On-chip AES/SHA/RNG cryptographic accelerators free up CPU cycles for protocol stacks (對比STM32F407VGT6)
- 1.71 V - 3.6 V supply range with 16-bit SAR ADC for direct low-voltage transducer interfacing (對比MK50DN512CLQ10)
設計說明
Decouple the MK60DN512VLQ10 with a 4.7 uF + 0.1 uF ceramic pair within 5 mm of the VDD pins, and an additional 0.1 uF + 1 uF pair on VDDA, VREFH, and VREFL. The 16-bit ADC cannot meet its 70 dB SNR spec if these pins share a noisy switching-rail return - place a ferrite bead between VDD and VDDA for boards that derive both from a single 3.3 V switching regulator. Brown-out reset (LVD) holds the part below 1.85 V; design the rail to ramp monotonically past this threshold before the crystal stabilises.
Estimated: at full 100 MHz core activity with all peripherals enabled, the LQFP-144 consumes approximately 220 mW; on a 4-layer JEDEC EIA/JESD51 board the theta_JA is around 38 C/W, yielding a 8 C rise above ambient. Inducted thermal headroom is therefore ample even at +105 C ambient. For sealed enclosures, de-rate by adding a copper pour 1 square inch on top of the device body or use the thermal pad variations (LQFP-144 with exposed pad) for roughly 35 percent improvement.
Place the 25 MHz reference crystal within 5 mm of EXTAL/XTAL pins and route the traces symmetrically with a ground guard ring. The Ethernet MII/RMII signals to the external PHY require 50 ohm controlled impedance on a 100-ohm differential pair for RMII; keep these traces under 50 mm total length. JTAG/SWD header should be brought out on a 2x5 0.05-inch connector compatible with Kinetis design-studio tag-connect for factory programming.
Avoid enabling the on-chip 16-bit ADC in DMA double-buffered mode without configuring the PDB (Programmable Delay Block) first - the default reset state leaves the ADC in software-trigger mode at approximately 3 MHz conversion rate, which limits clean-sample rate to 1 MSPS and halves the achievable ENOB to around 13 bits. Always populate a 100 kohm pull-up on the RESET_b pin even when no external supervisor is used.
The MK60DN512VLQ10 IEEE 1588 timestamp accuracy is rated at plus or minus 50 ns when the Ethernet reference clock is fed from a TCXO rather than the standard 25 MHz crystal. Add a TCXO footprint option if the design must support 802.1AS grand-master synchronisation; otherwise the on-chip 1588 timestamping is sufficient for distributed-clock slave synchronisation only.
合規資訊
RoHS compliant per NXP product page; lead-free finish on LQFP-144; halogen-free per NXP material declaration. Not AEC-Q100 qualified - for automotive applications choose the KEAZ or S32K sub-family.
