OPA2634U - Dual 250V/us Wideband Amplifier | Texas Instruments
MPN: OPA2634U ✓ 啟用中OPA2634U 概覽
An operational amplifier is an analog integrated circuit that amplifies the voltage difference between its inverting and non-inverting inputs. The OPA2634U belongs to the voltage-feedback operational-amplifier family, combining a wide frequency-response range with high output-current capability. This makes it useful when a signal must be amplified accurately across a broad bandwidth or driven into a relatively low-impedance load.
Principal features include a 250 V/us slew rate, input-voltage noise density of 5.6 nV/Hz, high output current of 80 mA, and a 73 mA rated output-current or output-current-per-channel value. The amplifier operates from 2.7 V to 10 V, supports operation down to +3 V or +5 V, and can produce a 4.8 V output swing from a +5 V supply. The package is an 8-pin SOIC suitable for conventional surface-mount assembly.
The high slew rate allows large-amplitude signals to change quickly, while the low-noise input stage supports amplification of small signals and instrumentation signals. Input operation extending to ground is particularly useful in single-supply systems because the amplifier can process signals referenced close to the lower supply rail without a negative supply. The 80 mA output-current capability also provides more drive than a typical low-power signal-conditioning amplifier.
Typical uses include video-signal amplification, communications-interface buffering, data-conversion support, test and measurement equipment, and industrial control or instrumentation systems. The wide supply range also makes the device suitable for both 3.3 V and 5 V electronic systems where the signal amplitude and load require more bandwidth than a general-purpose precision amplifier can provide.
The principal design trade-off is power versus output-drive capability. A high slew rate and 80 mA output-current rating can increase dissipated power compared with low-power micropower amplifiers. Decoupling capacitors should be placed close to the supply pins, and output loading should be checked against the amplifier's drive and stability characteristics before large-signal deployment.
This page combines the OPA2634U electrical characteristics, package details, application guidance, comparison information, and sourcing-oriented technical context into one engineering reference. It also identifies where an exact drop-in substitute must be reviewed for supply range, bandwidth, slew rate, noise, package, and pin compatibility rather than relying on amplifier function alone.
直接替換替代品,適用於 OPA2634U — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
OPA2634UA
✅ 直接替換 ⚠️ 規格未經驗證📋 參考替代品(不在目錄中)
OPA2634UID
✅ 直接替換 ⚠️ 規格未經驗證📋 參考替代品(不在目錄中)
OPA2634UDB
✅ 直接替換 ⚠️ 規格未經驗證📋 參考替代品(不在目錄中)
OPA2634U 最大額定值與電氣特性
| Amplifier Type | Dual voltage-feedback operational amplifier |
| Number of Channels | 2 channels |
| Supply Voltage Range | 2.7 V to 10 V |
| Nominal Single-Supply Operation | +3 V or +5 V |
| Slew Rate | 250 V/us |
| Input Voltage Noise Density | 5.6 nV/Hz |
| High Output Current | 80 mA |
| Rated Output Current per Channel | 73 mA |
| Output Swing on +5 V Supply | 4.8 V |
| Input Common-Mode Range | Includes ground |
| 封裝 | 8-pin SOIC |
| Packaging | Tube |
| 安裝類型 | Surface mount |
OPA2634U 8-pin soic 腳位配置指南
OPA2634U(8-pin soic 封裝)的腳位配置。 此類比元件具有輸入、輸出與電源腳位。偏移歸零、補償與致能腳位配置請參閱製造商資料表。適用於訊號調理與放大器電路。
無詳細腳位定義資料: OPA2634U.
請參閱 資料表 以查看完整腳位配置。
典型應用
OPA2634U 適用於 6 應用s: Video Signal Amplification, Communications Interface Buffering, Precision Instrumentation Signal Chain, Data Acquisition Front End, Active Filtering and Signal Conditioning, Test and Measurement Equipment.
Video Signal Amplification
The OPA2634U fits video and other high-slew-rate signal paths because its 250 V/us slew rate preserves large-amplitude transitions and its 5.6 nV/Hz input noise supports low-level signal amplification. The amplifier can operate from a single +5 V supply while producing an output swing up to 4.8 V, making it useful for line-driver, buffer, and gain-stage roles with moderate loading. Its input range includes ground, which simplifies signal conditioning around video signals referenced near the lower rail. The design should still verify closed-loop gain, load capacitance, and stability against the manufacturer's typical curves before the amplifier is used close to its performance limits.
推薦
Communications Interface Buffering
The OPA2634U is suitable for communications-interface buffering where fast signal transitions and output drive are more important than minimum power consumption. Its 250 V/us slew rate reduces the risk of slew-limited distortion, while the 80 mA high output-current capability offers useful drive for cable, termination, or active-filter networks. Operation from 2.7 V to 10 V supports both +3 V and +5 V interface electronics, and the input range includes ground for single-supply coupling. When using the amplifier with reactive or capacitively loaded outputs, verify gain, phase margin, and load limitations using the manufacturer guidance rather than assuming that all loads are stable.
推薦
Precision Instrumentation Signal Chain
The OPA2634U can amplify small instrumentation signals where the 5.6 nV/Hz input-voltage noise density is valuable, while its 250 V/us slew rate preserves the time-domain response of dynamic sensor signals. The 73 mA rated output current per channel and 80 mA high output-current figure provide more drive than a typical micropower instrumentation amplifier. Its 2.7 V to 10 V operating range allows use in compact battery-powered and industrial systems, although the power draw should be compared against the system's thermal budget. For slow precision measurements, offset, bias-current, and drift requirements must also be checked; those values are not established by the listed headline characteristics.
推薦
Data Acquisition Front End
OPA2634U is appropriate for intermediate gain and drive stages in data-acquisition systems that require faster settling and greater output drive than a general-purpose precision amplifier. The 250 V/us slew rate helps preserve rapid input transitions, while the 5.6 nV/Hz input noise supports amplification of small converter outputs. A single +3 V or +5 V supply reduces system complexity, and the input range includes ground enables direct treatment of unipolar signals near zero volts. Designers should account for settling time, input bias current, offset voltage, and ADC drive requirements, and should verify that the selected gain and feedback network provide adequate stability.
推薦
Active Filtering and Signal Conditioning
The OPA2634U can serve as an active filter or general signal-conditioning element when the circuit benefits from high bandwidth and the ability to drive a wider range of loads. Its 250 V/us slew rate supports higher-frequency filter signals, and the 80 mA high output-current capability is advantageous with low-impedance filter stages. The amplifier's 2.7 V to 10 V supply range allows design reuse across +3 V and +5 V systems, while input operation down to ground simplifies single-supply filter biasing. Component tolerances, op-amp noise, and the filter's closed-loop stability determine the achievable response, so those parameters should be reviewed before production release.
推薦
Test and Measurement Equipment
OPA2634U is well suited to wideband test and measurement circuits because its 250 V/us slew rate combines with low 5.6 nV/Hz input noise and 80 mA high output-current capability. The dual configuration provides two independent amplifiers in one 8-pin SOIC, reducing board area when a measurement path requires a gain stage and a driver or buffer. A single +5 V supply can produce a 4.8 V output swing, while the input range includes ground for low-level unipolar signals. Instrument designers should still account for input offset, bias current, output swing at the actual load, and the calibration requirements of the complete measurement chain.
推薦
推薦產品摘要
工程參考資料,適用於 OPA2634U — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | OPA2634UA | OPA2634UID | OPA2634UDB |
|---|---|---|---|---|
| Package | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Amplifier Configuration | Dual voltage-feedback operational amplifier | Dual voltage-feedback operational amplifier | Dual voltage-feedback operational amplifier | Dual voltage-feedback operational amplifier |
| Supply Voltage Range | 2.7 V to 10 V | 2.7 V to 10 V | 2.7 V to 10 V | 2.7 V to 10 V |
| Slew Rate | 250 V/us | 250 V/us | 250 V/us | 250 V/us |
| Input Voltage Noise Density | 5.6 nV/Hz | 5.6 nV/Hz | 5.6 nV/Hz | 5.6 nV/Hz |
| High Output Current | 80 mA | 80 mA | 80 mA | 80 mA |
| Output Swing on +5 V Supply | 4.8 V | 4.8 V | 4.8 V | 4.8 V |
| Input Common-Mode Range | Includes ground | Includes ground | Includes ground | Includes ground |
| Number of Channels | 2 | 2 | 2 | 2 |
主要差異化特點
- High slew rate within a dual single-supply amplifier (對比OPA2634UA)
- Single-supply operation extends to 2.7 V (對比OPA2634UID)
- Low-noise wideband performance with substantial output drive (對比OPA2634UDB)
設計說明
Use separate bypass capacitors close to each amplifier's supply pins and connect the ground pins to a low-impedance ground plane. The OPA2634U supports 2.7 V to 10 V operation, but the usable supply range depends on the selected output amplitude, input common-mode range, and load current. Estimate power dissipation from the actual supply voltage and channel current before assigning copper area; the 250 V/us slew rate and 80 mA drive capability should not be interpreted as continuous full-current operation without thermal checks.
Place input, feedback, and decoupling components close to the corresponding SOIC pins to minimize parasitic capacitance and feedback-loop length. This is especially important because the OPA2634U's 250 V/us slew rate can expose layout-induced instability or ringing. Use the manufacturer pin-description table and typical-application circuits when assigning pins, and route output current away from sensitive input traces to reduce coupling.
Do not select an amplifier solely by package, bandwidth, or headline slew-rate rating. Confirm the exact pin assignments, supply range, input common-mode limits, output swing, load stability, offset, and bias-current requirements before approving a substitute. A 4.8 V output swing on +5 V does not imply rail-to-rail output, and an input range that includes ground does not by itself establish full rail-to-rail input operation.
For video, communications, or fast data-conversion interfaces, evaluate gain-bandwidth, slew-rate-limited settling, and capacitive loading together. The 250 V/us slew rate is valuable for large transitions, but it does not guarantee adequate accuracy for small-signal settling. Maintain short feedback paths, use the recommended resistor and capacitor values from the datasheet, and verify the completed circuit for oscillation with its actual source and load impedances.
合規資訊
Compliance declarations are not stated in the manufacturer or distributor results. AEC-Q100 is reported as unknown because this industrial operational amplifier is not identified as an automotive-qualified variant.