OPA2677T - 220MHz Dual Current-Feedback Op Amp | Texas Instruments
MPN: OPA2677T ✓ 啟用中OPA2677T 概覽
A current-feedback operational amplifier is a voltage-input, current-input feedback amplifier commonly called a CFB amplifier. Unlike the voltage-feedback topology used by many general-purpose op amps, a current-feedback amplifier controls bandwidth through feedback impedance and can maintain high speed as gain changes, subject to the recommended feedback network. Current-feedback amplifiers belong to the operational-amplifier hierarchy within analog signal-chain and power-management semiconductor systems.
The principal features of the OPA2677T include dual amplifier channels, 220 MHz bandwidth, unity-gain stability, high output current, and operation from a total supply voltage of up to 24 V. Its wide bandwidth supports DSL and power-line modem line-driving requirements, where signal amplitude, slew behavior, output loading, and distortion all affect data transmission quality. The manufacturer identifies the OPA2677 family as a SpeedPlus operational-amplifier platform.
OPA2677T uses a current-feedback topology rather than a conventional voltage-feedback architecture. This distinction is important when designing the feedback network because the compensation resistor value materially affects bandwidth and stability. The circuit should follow the feedback and decoupling guidance in the Texas Instruments OPA2677 datasheet rather than applying the resistor selection practices used for a voltage-feedback amplifier without verification.
Typical applications include xDSL line drivers, power-line modem transmitters, video-driver interfaces, high-speed signal conditioners, and communications equipment requiring a dual amplifier with broad bandwidth. The OPA2677 family is also available in SO-8, QFN-16, and HSOP-8 PowerPAD configurations, allowing engineers to select a package according to routing density, thermal requirements, and assembly capability.
For a robust implementation, place input, output, and decoupling connections close to the device, verify stability across the full gain and load range, and confirm that the selected external feedback components remain appropriate for the operating frequency. Output-current demand and source/sink capability should be checked against the intended line load rather than inferred from bandwidth alone.
This product page combines the exact orderable MPN, package information, application positioning, verified pricing structure, and engineering-focused selection guidance. It also distinguishes true same-footprint drop-in choices from family members that use a different package, helping PCB designers avoid replacements that require layout changes.
直接替換替代品,適用於 OPA2677T — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
此系列的變體
與下列產品可直接替換的同系列型號: OPA2677T (相同外形與佔位) — 差異在於 Amplifier Type, Package.
OPA2677U
✅ 直接替換聯絡詢價
查看資料表 →OPA2677H
✅ 直接替換 ⚠️ 規格未經驗證📋 參考替代品(不在目錄中)
OPA2677T 最大額定值與電氣特性
| Amplifier Type | Dual current-feedback operational amplifier |
| Number of Channels | 2 channels |
| Gain-Bandwidth Product | 220 MHz |
| Unity-Gain Stable | Yes |
| Maximum Total Supply Voltage | 24 V (±12 V operation) |
| Input Offset Voltage | 5300 uV maximum |
| Transconductance Bandwidth | 2 GHz |
| 封裝 | 16-SOIC, PDSO16 |
| 安裝類型 | Surface mount |
| RoHS 狀態 | unknown |
| REACH Status | unknown |
| AEC-Q100 Qualification | unknown |
OPA2677T 16-soic, pdso16 腳位配置指南
OPA2677T(16-soic, pdso16 封裝)的腳位配置。 此類比元件具有輸入、輸出與電源腳位。偏移歸零、補償與致能腳位配置請參閱製造商資料表。適用於訊號調理與放大器電路。
無詳細腳位定義資料: OPA2677T.
請參閱 資料表 以查看完整腳位配置。
典型應用
OPA2677T 適用於 6 應用s: xDSL Line Drivers, PLC Modem Transmitters, Wideband Video Signal Conditioning, High-Speed Communications Buffers, Industrial Test Signal Drivers, Power and Signal-Control Interfaces.
xDSL Line Drivers
The OPA2677T is well matched to xDSL line-driving circuits because it combines dual channels, 220 MHz gain-bandwidth performance, unity-gain stability, and high output-current capability. According to the Texas Instruments OPA2677 product page, the family is intended for xDSL applications where broadband signal integrity and load-driving strength are both important. Place the amplifier in the transmitter signal path and use the manufacturer-recommended feedback network. Verify output swing and current against the line-driver load because bandwidth alone does not establish suitability for every transformer or termination network.
推薦
PLC Modem Transmitters
OPA2677T suits power-line modem transmitters that require a wideband differential signal path and substantial output-drive capability. The Texas Instruments OPA2677 datasheet identifies high output current and low distortion as key requirements for PLC line driving, while the 220 MHz bandwidth supports fast signal transitions. Use the dual channels for complementary transmit paths when the circuit topology permits, and route the feedback and decoupling networks for minimal parasitic effects. Confirm the load, output compliance, and thermal margin before production release.
推薦
Wideband Video Signal Conditioning
The OPA2677T can condition wideband signals when the required closed-loop bandwidth remains within its 220 MHz gain-bandwidth capability and the load does not exceed the output-current limits. Its current-feedback architecture supports high-speed operation, but the feedback resistor must be selected using the OPA2677 guidance rather than generic op-amp practice. Keep input and feedback paths short to reduce parasitic feedback and ringing. Verify video timing, output swing, and stability with the actual source and termination impedance.
推薦
High-Speed Communications Buffers
OPA2677T can serve as a high-speed communications buffer where a dual wideband amplifier, unity-gain stability, and strong output drive are required. The 16-SOIC package provides separate amplifier channels for signal conditioning and impedance isolation, while the 220 MHz bandwidth supports demanding data paths. Select the feedback network from the manufacturer’s recommended values for the intended gain and load. Check output voltage swing, current margin, and channel behavior with realistic source and termination impedances.
推薦
Industrial Test Signal Drivers
OPA2677T is appropriate for industrial test and measurement front ends that need to drive high-bandwidth loads while maintaining a stable, low-distortion signal. Its dual-channel arrangement can support complementary or sequential test functions, and unity-gain stability simplifies direct buffer implementations. Because the current-feedback topology is sensitive to the feedback network and load, reproduce the manufacturer reference configuration before changing gain. Validate output compliance, source and sink current, temperature rise, and long-term stability across the instrument bandwidth.
推薦
Power and Signal-Control Interfaces
OPA2677T can be used in fast power-control and signal-control interfaces where a wideband amplifier must drive an analog network or supervisory circuit. The 220 MHz bandwidth and high output-current capability provide ample closed-loop speed for low-frequency control tasks and short transient events. Place output and feedback connections close to the device, maintain a low-impedance supply path, and decouple the rails near the package. Confirm that transient output current remains inside the device limits and that thermal conditions do not compromise signal accuracy.
推薦
推薦產品摘要
工程參考資料,適用於 OPA2677T — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 |
|---|---|
| Brand | Texas Instruments |
| Package | 16-SOIC (PDSO16) |
| Amplifier Type | Dual current-feedback operational amplifier |
| Number of Channels | 2 channels |
| Gain-Bandwidth Product | 220 MHz |
| Transconductance Bandwidth | 2 GHz |
| Unity-Gain Stable | Yes |
| Maximum Total Supply Voltage | 24 V (±12 V operation) |
| Maximum Input Offset Voltage | 5300 uV |
| Primary Application | xDSL and PLC line driving |
主要差異化特點
- Purpose-built current-feedback architecture (對比OPA2677U)
- Dedicated high-current line-driver performance (對比OPA2604AU)
- Dual-channel wideband integration (對比OPA2674)
設計說明
Route the OPA2677T feedback components directly between the amplifier output and its inverting input, with the shortest practical traces. Current-feedback amplifiers depend on the feedback impedance for stability, so extra trace resistance and capacitance can alter bandwidth or cause ringing. Keep the unused channel properly terminated according to the datasheet and avoid placing test pads or long stubs on high-impedance feedback nodes.
Place local supply-decoupling capacitors close to the device and follow the capacitance and placement recommendations in the Texas Instruments OPA2677 datasheet. Keep high-current output return paths separate from sensitive input and feedback traces to reduce ground bounce. Because the OPA2677T supports operation to ±12 V, verify the actual power-supply tolerance, startup sequence, and output-current demand before applying the maximum supply condition.
Do not use a feedback resistor selected for a voltage-feedback op amp without checking the OPA2677 current-feedback design guidance. Changes in source impedance, load, gain, and feedback resistance can affect closed-loop bandwidth and stability. Validate the amplifier with the final PCB, connector, cable, or line-network load, and check both source and sink current because wideband drive capability does not guarantee unlimited output-current capability.
Estimate SOIC temperature rise from actual supply voltage, output voltage, load current, and ambient temperature rather than bandwidth alone. The 16-SOIC package can be thermally constrained by its modest copper area and airflow. Reduce dissipation when possible by minimizing the output voltage drop, use generous ground-plane copper, and consider the family’s HSOP-8 PowerPAD option when the same electrical function can be redesigned around a different footprint.
合規資訊
No definitive compliance declarations were identified for the exact OPA2677T orderable MPN. Confirm the current material and environmental declarations with the manufacturer before production release.