OPA846ID - 1.75GHz Wideband Voltage-Feedback Op Amp | TI
MPN: OPA846ID ✓ 啟用中OPA846ID 概覽
A voltage-feedback operational amplifier is a gain-control device whose closed-loop bandwidth depends primarily on the noise gain selected by the feedback network. Unlike a current-feedback amplifier, a voltage-feedback amplifier maintains a defined gain relationship through its inverting and non-inverting inputs. The OPA846 combines this familiar topology with very high gain-bandwidth product and large-signal output drive, placing it within the high-speed analog amplifier category of the broader semiconductor and signal-processing hierarchy.
The principal features of the OPA846ID include a 1.75 GHz gain-bandwidth product, approximately 400 MHz amplifier bandwidth, 625 V/us slew rate, and low 12.6 mA supply current. The low-noise architecture is suitable for systems in which the amplifier must preserve small signals while operating at high frequencies. Its low distortion and high output-drive capability also make it more useful than a general-purpose precision op amp in video, communications, and instrumentation signal paths.
Internally, the OPA846 uses a classical differential input stage, two stages of forward gain, and a high-power output stage. This architecture combines low input-voltage noise with high bandwidth and large-signal performance. The differential stage provides the low-noise input behavior, the forward-gain stages establish the high gain-bandwidth product, and the output stage supplies the current needed to drive downstream circuits while maintaining low distortion. The manufacturer identifies the device as a single-circuit, voltage-feedback amplifier.
Typical applications include wideband active filters, video-signal conditioning, ultrasound and medical instrumentation, communications receivers, test-equipment front ends, and clock or data-processing interfaces. In these applications, the 1.75 GHz gain-bandwidth product supports operation at high closed-loop gains when the feedback network is designed carefully. The 625 V/us slew rate allows the output to track large-amplitude, high-frequency signals, while low noise helps preserve weak signals ahead of later amplification or conversion stages.
Designers should account for the bandwidth and stability consequences of the selected gain. The feedback resistors and compensation network determine the effective noise gain, and parasitic capacitance around the high-speed amplifier can alter stability. Short feedback paths, careful grounding, controlled impedance routing, and clean supply decoupling are particularly important at the bandwidth levels supported by this device. Component selection must also preserve adequate phase margin at the intended closed-loop gain and signal amplitude.
OPA846ID is ordered in an 8-pin SOIC package with an operating temperature range of -40°C to +85°C. This page combines manufacturer specifications, sourcing information, drop-in candidate review, comparison data, and practical high-speed layout guidance to support component selection and board-level implementation.
直接替換替代品,適用於 OPA846ID — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
此系列的變體
與下列產品可直接替換的同系列型號: OPA846ID (相同外形與佔位) — 差異在於 Amplifier Type, Gain-Bandwidth Product, Package, Slew Rate.
OPA846ID 最大額定值與電氣特性
| Amplifier Type | Voltage-feedback operational amplifier |
| Number of Circuits | 1 circuit |
| Gain-Bandwidth Product | 1.75 GHz |
| Bandwidth | 400 MHz |
| Slew Rate | 625 V/us |
| 供應電流 | 12.6 mA |
| 工作溫度範圍 | -40°C to +85°C |
| 封裝 | 8-pin SOIC (D) |
| Package Width | 3.90 mm |
| Lead Pitch | 1.27 mm |
OPA846ID 3.90 mm 腳位配置指南
OPA846ID(3.90 mm 封裝)的腳位配置。 此類比元件具有輸入、輸出與電源腳位。偏移歸零、補償與致能腳位配置請參閱製造商資料表。適用於訊號調理與放大器電路。
無詳細腳位定義資料: OPA846ID.
請參閱 資料表 以查看完整腳位配置。
典型應用
OPA846ID 適用於 6 應用s: Wideband Active Filters, Video Signal Conditioning, Communications Receiver Front Ends, Test and Measurement Front Ends, Medical and Ultrasound Signal Chains, Data Acquisition Signal Conditioning.
Wideband Active Filters
The OPA846ID fits wideband active-filter stages requiring low-noise input behavior and substantial bandwidth. Its 1.75 GHz gain-bandwidth product provides design margin above the approximately 400 MHz device bandwidth, while the 625 V/us slew rate improves large-signal behavior compared with a general-purpose precision amplifier. The 12.6 mA supply current supports power-conscious high-speed systems without changing the device's voltage-feedback architecture. Feedback values and compensation must be selected for the intended noise gain, and the PCB should minimize parasitic capacitance so that the realized filter response remains stable and repeatable.
Video Signal Conditioning
OPA846ID is appropriate for video-signal conditioning when a design needs more bandwidth and slew-rate margin than conventional precision op amps provide. The approximately 400 MHz bandwidth supports wideband video and control signals, and the 625 V/us slew rate reduces timing distortion on large transitions. Its low input-voltage noise helps preserve weak signal information before subsequent gain stages. The amplifier should be evaluated for output-swing and drive requirements against the actual source and load. Short feedback routes, solid ground return paths, and symmetrical decoupling are important because excessive trace inductance or capacitance can destabilize the high-speed feedback loop.
Communications Receiver Front Ends
The OPA846ID can serve as a high-speed gain and impedance-control stage in communications receiver front ends. Its 1.75 GHz gain-bandwidth product supports closed-loop gains well above the approximately 400 MHz small-signal bandwidth, while the low-noise input architecture is beneficial when amplification occurs before later signal processing. The 625 V/us slew rate preserves large-signal fidelity and the 12.6 mA supply current helps constrain system power. Designers should confirm the device's input common-mode range, output swing, supply requirements, and noise density for the particular receiver architecture, then preserve controlled impedance and short feedback paths.
Test and Measurement Front Ends
OPA846ID is well matched to oscilloscope driver, buffer, and general test-equipment front-end functions because it combines approximately 400 MHz bandwidth with a 625 V/us slew rate and low-noise input characteristics. These specifications help the amplifier drive downstream instrumentation while maintaining waveform shape and preserving small input signals. The single-circuit 8-pin SOIC implementation also supports compact analog sections around a probe interface. Validation should include the expected load capacitance, output-current demand, and sustained waveform amplitude. Use short, direct routing, adequate supply bypassing, and a controlled return path to prevent board parasitics from limiting the amplifier's stated performance.
Medical and Ultrasound Signal Chains
OPA846ID can support high-gain, wideband signal paths in medical instrumentation when the selected operating point meets the required safety, noise, and precision criteria. Its 1.75 GHz gain-bandwidth product provides closed-loop bandwidth margin, while the 625 V/us slew rate helps preserve rapid signal transitions. Low input voltage noise is favorable for weak transducer or sensor signals. Because a wideband amplifier does not by itself establish medical-system compliance, use it only after the complete signal chain has been evaluated for noise, distortion, leakage, operating temperature, and applicable regulatory requirements. Stable feedback layout remains essential in high-impedance sensor interfaces.
Data Acquisition Signal Conditioning
OPA846ID is suitable for high-speed data-acquisition front ends that need to amplify or buffer signals before digitization. Its approximately 400 MHz bandwidth and 1.75 GHz gain-bandwidth product offer margin for sampling systems, and the 625 V/us slew rate supports full-scale transitions with less timing distortion than lower-bandwidth amplifiers. Low input-voltage noise can improve the signal-to-noise ratio before conversion, although the complete system also depends on source impedance, ADC input range, and filtering. Keep the feedback loop compact, use low-capacitance routing, and place bypass capacitors close to the supply pins to reduce susceptibility to parasitic feedback and supply impedance effects.
工程參考資料,適用於 OPA846ID — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | THS4021ID |
|---|---|---|
| Brand | Texas Instruments | Texas Instruments |
| Package | 8-pin SOIC (D) | 8-pin SOIC |
主要差異化特點
- High published gain-bandwidth product (對比THS4021ID)
- Large-signal slew performance (對比THS4021ID)
- Low stated supply current for a wideband amplifier (對比THS4021ID)
設計說明
Keep the OPA846ID feedback network compact and route input, output, and feedback connections away from high-impedance or switching nodes. Place the input and output components close to their corresponding pins, and avoid routing the feedback return beneath the device or across parallel signal paths. At the amplifier's approximately 400 MHz bandwidth, small parasitic capacitances and long loops can alter phase margin and cause ringing or oscillation.
Use short, low-inductance connections from each supply pin to local bypass capacitors, and follow the manufacturer datasheet's recommended decoupling configuration. Decoupling should be placed directly across the relevant supply pins rather than at a distant power entry point. Because the OPA846ID draws 12.6 mA under the manufacturer's stated condition, the actual board power and junction-temperature estimate must also include output current, supply voltage, ambient temperature, and copper area.
Do not assume that the 1.75 GHz gain-bandwidth product is the usable closed-loop bandwidth at every gain. Effective bandwidth is governed by noise gain and stability, and the 625 V/us slew rate must also be sufficient for the largest expected signal amplitude and frequency. Before substituting another amplifier, verify noise density, offset voltage, supply range, common-mode range, output swing, output current, operating temperature, and compensation-network requirements.
Preserve controlled impedance for high-frequency signal routes and maintain a continuous ground reference beneath the analog section. Avoid long stubs and unnecessary test pads on sensitive nodes because their capacitance can increase peaking near the amplifier's upper bandwidth. If input, output, and supply connections cannot be kept short on the selected PCB stack-up, consider a smaller package or a different amplifier family with board-layout requirements better matched to the system.
合規資訊
The available manufacturer ordering information confirms the OPA846ID package and operating temperature but does not explicitly state RoHS, REACH, lead-free, halogen-free, or conflict-minerals status. AEC-Q100 qualification is not stated for this ordering code.