PCA9510D - 400kHz Hot-Swappable I2C Buffer | NXP
MPN: PCA9510D ✓ 啟用中PCA9510D 概覽
An I2C bus buffer is a specialized interface IC that electrically isolates or buffers two bus segments while preserving bidirectional serial-data and clock communication. The PCA9510D belongs to the interface-IC hierarchy used in hot-plug, expansion-card, server, and embedded backplane systems. Its SMBus compatibility extends the same isolation concept to systems using SMBus-based management or control functions.
The device operates as a single-channel, 400 kHz bus buffer. Its key function is controlled connection between the backplane and card sides: the card is not connected during an active bus transaction, reducing the risk of contention when either bus segment is active. The 8-SO package supports conventional surface-mount PCB assembly, while the PCA9510D,118 ordering suffix identifies a specific distributor orderable variant.
The PCA9510D is intended for systems in which modules may be inserted or removed without powering down the entire host. NXP describes the device as providing bidirectional bus buffering once the connection is permitted. The relevant engineering benefit is operational continuity and reduced insertion disturbance rather than longer trace distance or level translation; no galvanic isolation or voltage-level translation should be inferred from the hot-swap function.
Typical uses include server and workstation expansion cards, telecommunications equipment, industrial controller modules, test systems, and embedded backplanes that expose an I2C or SMBus connection to removable hardware. The PCA9510D is particularly relevant when the card connector may be populated or serviced while the host remains active and the bus must not be corrupted during insertion.
Design attention should focus on system enable control, power sequencing, bus idle detection, and the electrical behavior of the card-side connector. The protection mechanism depends on observing a valid bus condition before connecting the two segments. Designers should therefore verify startup states, fault conditions, and connector sequencing rather than treating the PCA9510D as an ordinary passive I2C buffer.
This page combines the manufacturer function description, package and frequency information, orderable part references, and practical hot-plug guidance to support PCB, sourcing, and replacement decisions. It also distinguishes verified device identity from specifications that require confirmation against the manufacturer datasheet before electrical sign-off.
直接替換替代品,適用於 PCA9510D — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
此系列的變體
與下列產品可直接替換的同系列型號: PCA9510D (相同外形與佔位) — 差異在於 Package, Lifecycle Status, Product Type.
PCA9510ADP,118
✅ 直接替換聯絡詢價
查看資料表 →PCA9510D 規格
| Product Type | Hot-swappable I2C-bus and SMBus buffer |
| Bus Interface | I2C and SMBus |
| Maximum Bus Frequency | 400 kHz |
| Channel Count | 1 channel |
| Data Direction | Bidirectional |
| 封裝 | 8-SO, 8 pins |
| Package Type | Gull-wing surface-mount SO |
| 安裝類型 | Surface mount |
| Temperature Grade | Industrial |
| Hot-Plug Control | STOP-command or bus-idle connection control |
| Terminal Count | 8 terminals |
| Product Form | Rectangular surface-mount package |
PCA9510D gull-wing surface-mount so 腳位配置指南
PCA9510D(gull-wing surface-mount so 封裝)的腳位配置。 腳位編號、功能與連接圖定義於製造商資料手冊中。請參閱該手冊以取得確切的封裝尺寸與焊接指引。
無詳細腳位定義資料: PCA9510D.
請參閱 資料表 以查看完整腳位配置。
典型應用
PCA9510D 適用於 6 應用s: Hot-Plug Server Expansion Cards, Industrial Controller Module Backs, Telecommunications Backplane Cards, Embedded Test and Measurement Modules, Removable Communication Modules, General I2C and SMBus Card Insertion.
Hot-Plug Server Expansion Cards
The PCA9510D fits an I2C or SMBus management connection on a removable server expansion card because it delays connection of the card-side bus until the backplane reaches a safe idle state or a STOP command is detected. At the 400 kHz class operating point, the buffer supports normal management-bus traffic while preventing an inserted card from immediately driving an active bus. The system must still sequence connector power and validate bus capacitance, pull-up strength, and startup behavior. Its principal benefit is reduced insertion contention without requiring the complete host system to power down.
推薦
Industrial Controller Module Backs
The PCA9510D is useful between an industrial controller backplane and a removable I/O module that communicates through I2C or SMBus. Controlled connection prevents the module from joining the bus during an active transaction, while the single-channel bidirectional architecture preserves data and clock communication between the two segments. At up to 400 kHz, it accommodates common low-speed management interfaces. Designers should confirm the industrial temperature limits, supply range, and startup-state behavior against the manufacturer datasheet before deploying it in temperature-extreme or safety-related equipment.
推薦
Telecommunications Backplane Cards
The PCA9510D can isolate a card-side I2C or SMBus segment from a live telecommunications backplane during field replacement or inventory expansion. Its STOP-command or bus-idle connection logic reduces the risk of corrupting management traffic while a card is inserted, and the 400 kHz operating class is appropriate for supervisory and configuration interfaces. The device does not by itself solve power hot-plug sequencing, connector bounce, or ground-transient problems; those functions must be designed around it. Validate bus loading and signal integrity across the complete backplane length.
推薦
Embedded Test and Measurement Modules
The PCA9510D is appropriate when a plug-in test module accesses an I2C or SMBus instrumentation bus that remains active during module replacement. The controlled connection sequence reduces bus contention and helps preserve communication on the host side. Its 400 kHz class rating supports many configuration, status, and low-bandwidth measurement-control interfaces without implying support for faster high-speed I2C modes. The test chassis should control module power before enabling bus communication and should verify that the bus-idle detector behaves correctly under low-speed traffic and abnormal card states.
推薦
Removable Communication Modules
The PCA9510D can support serviceable radio, network, and data-acquisition modules that expose an I2C or SMBus configuration interface. Bidirectional buffering preserves command and status traffic, while the delayed-connection feature prevents the module from driving the host bus during mechanical insertion. The 400 kHz class operating point is suitable for configuration and status traffic rather than payload streaming. Engineering validation should cover connector sequencing, bus pull-ups, card-side power-up timing, and the time required for the buffer to recognize a valid idle condition.
推薦
General I2C and SMBus Card Insertion
The PCA9510D is appropriate for a general embedded expansion interface where cards may be inserted while the system remains powered and the I2C or SMBus is active. Unlike a continuously connected buffer, the PCA9510D waits for a STOP command or bus-idle condition before joining the two bus segments, reducing contention during insertion. The 8-SO package supports standard surface-mount assembly, and the 400 kHz operating class fits conventional control buses. Confirm the exact pin functions, supply requirements, and electrical limits in the manufacturer datasheet before layout release.
推薦
推薦產品摘要
工程參考資料,適用於 PCA9510D — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | PCA9510A | PCA9511D |
|---|---|---|---|
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Package | 8-SO | 8-SO | 8-SO |
| Product Type | Hot-swappable I2C-bus and SMBus buffer | Hot-swappable I2C-bus and SMBus buffer | Hot-swappable I2C-bus and SMBus buffer |
| Maximum Bus Frequency | 400 kHz | 400 kHz | 400 kHz |
| Mounting Type | Surface mount | Surface mount | Surface mount |
主要差異化特點
- Controlled connection protects an active backplane during card insertion (對比PCA9511D)
- Same 400 kHz bus-class and bidirectional function (對比PCA9510A)
- Same 8-SO footprint family supports compact interface layouts (對比PCA9510A)
設計說明
Separate connector-power sequencing from bus-connection sequencing. The PCA9510D controls when the card-side and backplane-side bus segments are connected, but it does not guarantee that every card supply rail is ready when the connection occurs. Hold the card in reset or keep its I2C drivers disabled until its local supply is stable. Check the device and connected-card supply limits against the manufacturer datasheet before fixing the system voltage plan.
Place the PCA9510D close to the connector or card-side interface so the isolated segment remains short, while routing the backplane-side connection directly toward the host bus. Keep ground returns continuous and use the package pin definition from the manufacturer datasheet when assigning tracks. Do not assume that the enable and bus-side pins of PCA9510A and PCA9511D are interchangeable solely because both devices use an 8-SO outline.
Validate pull-up placement, bus capacitance, rise-time behavior, and the 400 kHz operating limit across the complete interconnect rather than only the PCB traces. During insertion, connector bounce and card-side power-up can create transient bus states. Confirm that the backplane is idle or a STOP command is detected before the controlled connection takes effect, and use oscilloscope measurements to verify clock and data integrity at the connector and remote endpoint.
Do not substitute a generic I2C buffer for the PCA9510D when hot-plug protection is required. A standard repeater may connect the two bus sides continuously and therefore lacks the PCA9510D's STOP-command or bus-idle connection control. Also avoid treating the device as galvanic isolation or automatic voltage-level translation; verify supply domains and logic thresholds from the manufacturer documentation.
合規資訊
The device is an industrial-temperature interface IC, but no device-specific RoHS, REACH, lead-free, halogen-free, or conflict-minerals declaration is stated for PCA9510D. AEC-Q100 is not applicable to this non-automotive interface-device category.