PCM1862DBT - 24-Bit 192kHz Stereo Audio ADC | TI
MPN: PCM1862DBT ✓ 啟用中PCM1862DBT 概覽
An audio ADC is a semiconductor that converts analog left- and right-channel audio signals into digital data for processing, storage, transmission, or playback. It belongs to the signal-conversion hierarchy: ADC → data converter → integrated circuit, and it sits between an analog microphone or line-level front end and a digital signal processor, MCU, or audio codec. A universal front end integrates gain, filtering, and analog input conditioning to reduce the number of external components required in a stereo audio subsystem.
Key features include 103 dB dynamic range, 24-bit resolution, 192 kSPS maximum sampling, two analog input channels, and a single 3.3 V supply. The integrated software-controlled PGA reduces the need for discrete analog gain stages, while I2C and SPI interfaces support flexible control from embedded processors. A 30-pin TSSOP package also makes the PCM1862 practical for compact industrial, communications, and consumer audio equipment.
The PCM1862 family was developed around a universal audio front end intended to simplify high-performance end-product designs and support European Ecodesign objectives. Software configuration reduces the number of external controls and permits operating modes to be selected through the digital interface. Its single-supply operation also simplifies power architecture compared with converters requiring a separate 5 V analog rail or external programmable-gain stage.
Typical uses include microphone-array capture, voice interfaces, industrial monitoring, USB audio front ends, and embedded stereo recording. In a typical design, analog signals enter through the integrated input network, the selected PGA gain is programmed over I2C or SPI, and the resulting PCM data is transferred to a host processor. System designers must select suitable input and reference circuitry based on the source impedance, signal level, and required noise performance.
A key design consideration is the analog and digital layout. Keep input traces short, provide a quiet analog ground path, decouple the supply close to the device, and follow the manufacturer pin descriptions when assigning the 30 TSSOP connections. Verify the selected interface mode, system clock, channel mapping, and gain settings in firmware because configuration errors can appear as incorrect gain, channel interchange, or digital-format incompatibility.
This page combines the PCM1862DBT specifications, family-level drop-in options, interface guidance, and application-oriented design notes to support component selection, schematic review, PCB planning, and procurement decisions. The comparison tables also identify which parameter values require verification for a particular production design.
直接替換替代品,適用於 PCM1862DBT — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
PCM1860DBT
✅ 直接替換 ⚠️ 規格未經驗證📋 參考替代品(不在目錄中)
PCM1861DBT
✅ 直接替換 ⚠️ 規格未經驗證📋 參考替代品(不在目錄中)
PCM1863DBT
✅ 直接替換 ⚠️ 規格未經驗證📋 參考替代品(不在目錄中)
PCM1864DBT
✅ 直接替換 ⚠️ 規格未經驗證📋 參考替代品(不在目錄中)
PCM1865DBT
✅ 直接替換📋 參考替代品(不在目錄中)
PCM1862DBT 最大額定值與電氣特性
| ADC Type | Software-controlled audio ADC with universal front end |
| Channel Count | 2 channels |
| 解析度 | 24 bit |
| Maximum Sampling Rate | 192 kSPS |
| Dynamic Range | 103 dB |
| 供應電壓 | 3.3 V |
| Supply Configuration | Single supply |
| Digital Control Interface | I2C and SPI |
| Programmable Gain Amplifier | Integrated and software controlled |
| Analog Front End | Universal front end |
| 封裝 | 30-pin TSSOP (DBT) |
| 工作溫度範圍 | -40 °C to +125 °C |
| 安裝類型 | Surface mount |
| External Programmable-Gain Stage | Not required |
| Separate 5 V Supply | Not required |
PCM1862DBT 30-pin tssop (dbt) 腳位配置指南
PCM1862DBT(30-pin tssop (dbt) 封裝)的腳位配置。 此類比元件具有輸入、輸出與電源腳位。偏移歸零、補償與致能腳位配置請參閱製造商資料表。適用於訊號調理與放大器電路。
無詳細腳位定義資料: PCM1862DBT.
請參閱 資料表 以查看完整腳位配置。
典型應用
PCM1862DBT 適用於 6 應用s: Stereo Microphone Capture, Industrial Audio Monitoring, Voice Recognition Interface, USB Audio Front End, Network Communication Equipment, Portable Audio Measurement.
Stereo Microphone Capture
The PCM1862DBT fits stereo microphone capture because it combines two analog input channels, a software-controlled PGA, 24-bit conversion, and operation from a single 3.3 V rail. A host processor can configure gain and operating mode through I2C or SPI, reducing the need for separate analog gain-control circuitry. The converter's 103 dB dynamic range and 192 kSPS capability preserve a broad range of source levels and support high-resolution recording. In implementation, treat the microphone bias, source impedance, and analog grounding as part of the converter's input network. Keep the two input paths symmetrical, position input and bypass capacitance near the device, and separate microphone or line input routing from SPI and I2C activity. Firmware should confirm channel mapping, PGA settings, clock source, and the selected digital audio format before normal operation.
推薦
Industrial Audio Monitoring
PCM1862DBT is suitable for industrial monitoring equipment requiring two synchronized audio channels without a separate 5 V converter rail. Its 3.3 V single-supply operation simplifies power partitioning in equipment that also contains 3.3 V control electronics, while 24-bit resolution and 103 dB dynamic range support faithful capture of low-level acoustic events. The universal front end and integrated software-controlled gain reduce the component count compared with a discrete analog preamplifier. For machinery or environmental monitoring, route both inputs away from switching nodes and high-current return paths. Use the manufacturer's recommended input network and bypass arrangement, and verify whether the selected PGA range preserves headroom without excessive attenuation. Software should detect clipping and out-of-range conditions so that maintenance data reflects the actual signal level.
推薦
Voice Recognition Interface
The PCM1862DBT can serve as the analog-to-digital front end in a voice-recognition system that needs more precision than a basic 8-bit or 16-bit audio interface. Two channels permit simultaneous microphone capture or a microphone-plus-line-input arrangement, and the integrated programmable gain helps position the signal within the converter's range. Its maximum 192 kSPS rate permits oversampling relative to common voice-processing rates. The PCM1862's digital configuration interface also allows firmware to select gain and operating parameters without adding a separate analog control bus. Place the microphone or line-input network close to the converter, maintain a quiet analog return path, and provide local supply bypassing. Confirm the system clock and data framing expected by the speech processor so that no resampling or channel-swap correction is required later.
推薦
USB Audio Front End
PCM1862DBT fits a USB audio front end that translates a stereo analog source into 24-bit digital samples for a USB audio controller. Its single 3.3 V operation can simplify board-level power distribution, while I2C or SPI control allows the host firmware to adjust gain and operating modes. Support for sampling rates up to 192 kSPS accommodates high-resolution playback and capture requirements, and the 103 dB dynamic range is appropriate for consumer and pro-audio conversion tasks. Interface timing between the PCM1862 and USB controller must be reviewed carefully, including clock generation, frame alignment, and supported data formats. Keep switching regulators and USB routing away from the analog inputs, use the recommended decoupling network, and verify whether the host requires a specific I2C address or serial timing configuration.
推薦
Network Communication Equipment
PCM1862DBT is applicable to network communication equipment that captures announcement, alarm, or conferencing audio alongside digital data. The two-channel ADC supports paired inputs, while the 3.3 V supply and compact 30-pin TSSOP package simplify integration into communication modules. The 24-bit conversion format and 103 dB dynamic range provide headroom for speech and general-purpose audio, and software-controlled gain enables firmware to accommodate different source levels. Keep analog and digital sections partitioned on the PCB, particularly where Ethernet magnetics, switching regulators, or high-speed clocks are present. Use a controlled reference and grounding strategy, and validate that the converter's clock remains stable when the communication system enters different traffic or power states. Firmware should apply channel checks and gain calibration during startup to maintain consistent capture quality.
推薦
Portable Audio Measurement
PCM1862DBT can be used in portable or compact audio measurement equipment where two channels, low supply complexity, and high-resolution conversion are valuable. Its 3.3 V single-supply operation suits battery-managed designs, and the integrated software-controlled PGA reduces the number of external analog adjustments. The 103 dB dynamic range supports comparisons across microphones, pickups, and other sensors, while operation up to 192 kSPS allows higher-rate analysis where the source and mechanical system support it. Low-power operation still requires careful clock and duty-cycle planning. Disable unused channels or configure lower operating modes through the control interface, and ensure that the analog source can tolerate the selected input impedance. Validate the full signal chain with known calibration signals, and separate converter routing from display, charger, and wireless circuitry to minimize measurement noise.
推薦
推薦產品摘要
工程參考資料,適用於 PCM1862DBT — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | PCM1860DBT | PCM1861DBT | PCM1863DBT | PCM1864DBT | PCM1865DBT |
|---|---|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | 30-pin TSSOP (DBT) | 30-pin TSSOP (DBT) | 30-pin TSSOP (DBT) | 30-pin TSSOP (DBT) | 30-pin TSSOP (DBT) | 30-pin TSSOP (DBT) |
主要差異化特點
- Provides two-channel conversion in one device (對比PCM1865DBT)
- Single 3.3 V supply simplifies power architecture (對比PCM1861DBT)
- Integrated software-controlled gain reduces external analog control (對比PCM1860DBT)
- 103 dB dynamic range supports high-resolution capture (對比PCM1863DBT)
設計說明
Treat the analog inputs as high-impedance signal paths. Keep the PCM1862 input traces short, minimize loop area, and place input-network components close to the assigned pins. Route SPI, I2C, clock, and data signals away from the input and reference nodes. Use the manufacturer application circuit as the PCB template and preserve its recommended analog and digital partitioning.
Decouple the 3.3 V supply close to the device using the capacitance and placement specified by the manufacturer datasheet. Keep switching-regulator and digital-supply return currents from crossing the analog input and reference paths. Verify startup sequencing, supply ripple at the converter pins, and the operating current required by the selected PCM1862 configuration before finalizing the power tree.
Do not treat a matching TSSOP outline as proof of complete interchangeability. Compare every pin, the required channel count, clocking scheme, register map, and control interface behavior between the PCM1862DBT and the proposed family member. The alternatives may use the same 30-pin package while providing a different number of audio channels, making schematic and firmware changes necessary.
Program the PGA and operating mode before applying a signal to production inputs, and establish a repeatable gain structure that preserves headroom for the loudest expected source. Check channel mapping, digital data alignment, and clipping status during startup. For microphone or line-input circuits, validate source impedance and grounding using the manufacturer's front-end design rather than adding arbitrary input resistance.
合規資訊
Use the current Texas Instruments material declarations and product compliance documents for the authoritative RoHS, REACH, lead-free, halogen-free, conflict-minerals, and automotive qualification status.