PCM3501E/2K - 16-Bit Mono Voice Codec | Texas Instruments
MPN: PCM3501E/2K ✓ 啟用中PCM3501E/2K 概覽
A voice codec is an interface IC that converts between analog audio signals and digital PCM data. The PCM3501E/2K belongs to the broader codec hierarchy: integrated circuit, interface IC, audio codec, and mono voice or modem codec. This device is intended for compact systems where one communication voice channel must be digitized and reproduced without the channel count or power requirements of a stereo audio codec.
The codec provides a 16-bit PCM serial interface, a mono voice or modem signal path, and operation from a 2.7 V to 3.6 V analog supply. Its low-voltage and low-power characteristics suit portable and embedded communication equipment in which the codec must operate alongside 3.3 V digital logic. The 24-pin SSOP package also supports conventional surface-mount assembly and automated production.
Because the device handles both analog conversion and digital serialization, its performance depends on correct power distribution, grounding, and interface implementation. A clean 3.3 V supply helps prevent converter reference or digital-interface disturbances from reaching the voice path. The manufacturer datasheet should be used for clock timing, analog biasing, filtering, and decoupling values because those detailed operating conditions are not reproduced on this page.
Typical uses include single-channel voice processing in modem and telephone interface equipment, compact audio communication terminals, digital answering devices, and embedded voice-capable appliances. In each case, the PCM3501E/2K serves as the bridge between an analog microphone or line-level voice signal and a digital processor or serial interface.
For a new PCB, use the 24-pin SSOP footprint and follow the pin-description table in the manufacturer datasheet when assigning analog, digital, clock, and supply connections. For an existing PCM3501E design, verify package orientation, supply sequencing, clock source, and the PCB land pattern before treating the /2K tape-and-reel ordering option as a replacement.
This page brings together the manufacturer ordering information, package details, drop-in comparison data, and practical integration guidance. It also distinguishes electrical and functional interchangeability from the distinction between tube and tape-and-reel delivery configurations, helping engineers make a more reliable sourcing and assembly decision.
直接替換替代品,適用於 PCM3501E/2K — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
此系列的變體
與下列產品可直接替換的同系列型號: PCM3501E/2K (相同外形與佔位) — 差異在於 Digital Interface.
PCM3501E/2K 規格
| Codec Type | Mono voice/modem codec |
| 解析度 | 16 bit |
| Channel Count | 1 channel |
| Supply Voltage Range | 2.7 V to 3.6 V |
| Digital Interface | 16-bit serial PCM |
| Signal Class | SoundPlus voice/modem codec |
| 封裝 | 24-pin SSOP (DB) |
| 腳位數 | 24 pins |
| 安裝類型 | Surface mount |
| Operating Voltage | 2.7 V to 3.6 V |
| Power Class | Low power |
| Delivery Format | Tape and reel |
| Reel Quantity | 2,000 devices per reel |
| RoHS 狀態 | unknown |
| REACH Status | unknown |
PCM3501E/2K 24-pin ssop (db) 腳位配置指南
PCM3501E/2K(24-pin ssop (db) 封裝)的腳位配置。 腳位編號、功能與連接圖定義於製造商資料手冊中。請參閱該手冊以取得確切的封裝尺寸與焊接指引。
無詳細腳位定義資料: PCM3501E/2K.
請參閱 資料表 以查看完整腳位配置。
典型應用
PCM3501E/2K 適用於 6 應用s: Single-Channel Modem Interface, Voice Terminal and Answering Device, Portable Voice Communications, Digital Voice Processing Node, Industrial Voice Control Panel, Voice Access and Security Panel.
Single-Channel Modem Interface
The PCM3501E/2K fits a single-channel modem or telephone interface that must convert one analog voice signal into 16-bit PCM data and reproduce the decoded voice channel. Its 2.7 V to 3.6 V operating range accommodates a 3.3 V communication subsystem, while the mono codec topology avoids the channel overhead of a stereo converter. Place the codec beside the analog input and output networks, connect it to the system serial interface, and decouple the supply close to the device. Because clock and analog bias details determine usable voice performance, the implementation should follow the pin configuration, timing requirements, and reference circuit in the manufacturer datasheet rather than infer those values from the package outline.
推薦
Voice Terminal and Answering Device
The PCM3501E/2K is appropriate for compact voice terminals, answering devices, and communication appliances that require one recorded or transmitted voice channel. The 16-bit mono conversion provides a straightforward PCM stream for a digital processor, and the low-voltage operation supports systems built around 3.3 V logic. Keep the microphone or line-input conditioning close to the analog pins, provide the required bypass capacitance at the supply entry, and isolate digital clock routing from the analog output path. The principal engineering trade-off is that this is a mono codec: it supports one communication voice path rather than the independent left and right channels expected in a stereo audio product, so stereo recording or playback requires another converter.
推薦
Portable Voice Communications
The PCM3501E/2K can serve as the voice conversion element in portable or embedded communication equipment powered from a low-voltage 3.3 V rail. Its stated low-power design and 2.7 V to 3.6 V operating range suit compact systems, while the single 16-bit mono channel reduces component and routing requirements relative to a stereo codec. In a portable design, verify the codec supply requirement against the battery system and regulator headroom, then place the analog and bypass networks close to the package to limit board-area pickup. The SSOP package supports compact surface-mount layouts, but thermal, clock, and supply-noise performance remain dependent on correct decoupling and layout practices specified by the manufacturer.
推薦
Digital Voice Processing Node
The PCM3501E/2K fits a distributed voice-processing node that receives or produces one digital audio stream while also requiring an analog microphone or line interface. Its serial PCM interface allows the codec to connect to a communications processor, while the mono topology provides an economical conversion path for speech or modem content. Route serial data away from analog inputs, use a continuous ground reference between the analog and digital sections, and confirm clock polarity and timing against the system controller. Since the codec includes only one voice-band signal path, a node requiring simultaneous talk and listen channels must account for additional conversion resources rather than assuming stereo capability.
推薦
Industrial Voice Control Panel
The PCM3501E/2K is suitable for an industrial control panel or machine interface that needs a single voice channel for operator communication or audible prompting. Its 3.3 V-compatible operating range allows integration with conventional embedded control logic, while the 16-bit mono path provides digital voice data without requiring a high-channel-count audio converter. Place the analog front end and codec together to reduce susceptibility to switching-node interference, and use a low-impedance ground strategy that satisfies both analog return requirements and digital signal integrity. The device does not replace an audio amplifier or speaker driver; those functions remain downstream, and the complete voice chain must account for microphone biasing, line-level conditioning, and output amplification.
推薦
Voice Access and Security Panel
The PCM3501E/2K can support a voice-access module that captures one mono voice channel for recognition or communication and returns a decoded voice prompt. Its low-voltage operation is compatible with 3.3 V embedded systems, and the 24-pin SSOP package permits a relatively compact mixed-signal board. Maintain short analog traces, place bypass components at the supply pins, and keep switching-regulator and high-current return paths away from the codec's analog section to minimize interference. The converter itself does not provide voice recognition, microphone biasing, or speaker amplification, so those functions must be designed separately. Its single-channel nature makes it well matched to command-band access systems but not to simultaneous multi-microphone or full-stereo requirements.
推薦
推薦產品摘要
工程參考資料,適用於 PCM3501E/2K — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | PCM3501E |
|---|---|---|
| Package | 24-pin SSOP (DB) | 24-pin SSOP (DB) |
| Brand | Texas Instruments | Texas Instruments |
| Codec Function | Mono voice/modem codec | Mono voice/modem codec |
| Resolution | 16 bit | 16 bit |
| Supply Voltage Range | 2.7 V to 3.6 V | 2.7 V to 3.6 V |
| Digital Interface | 16-bit serial PCM | 16-bit serial PCM |
| Signal Class | SoundPlus voice/modem codec | SoundPlus voice/modem codec |
| Delivery Format | Tape and reel, 2,000 devices per reel | Tube |
| Pin Compatibility | 24-pin SSOP footprint | Consistent terminals and package |
| Power Class | Low power | Low power |
主要差異化特點
- Production-friendly 2,000-piece reel format (對比PCM3501E)
- Direct pin-compatible reuse of an existing codec footprint (對比PCM3501E)
- Equivalent single-channel voice conversion (對比PCM3501E)
設計說明
Treat the analog and digital sections as separate return paths even though both operate from the same low-voltage supply. Place the required bypass capacitors at the supply pins, keep analog input and output traces short, and avoid routing serial clock or data lines beneath the analog signal area. The 24-pin SSOP footprint should follow the land pattern and pin-one orientation in the Texas Instruments package drawing.
Do not interchange PCM3501E/2K and PCM3501E without recording the delivery requirement. The electrical codec functions and 24-pin SSOP package are consistent, but /2K specifies a 2,000-piece tape-and-reel order while PCM3501E is identified as a tube configuration. Confirm the assembler, incoming-inspection process, quantity planning, and moisture-handling requirements before changing the order code.
Use a continuous ground plane and keep high-current switching or digital return currents away from the codec analog pins. Follow the manufacturer reference configuration for clock generation, analog bias, input and output filtering, and decoupling. Because the codec converts one analog voice channel while sending serial PCM data, clock-edge timing and analog settling must both be satisfied before increasing system volume or operating rate.
合規資訊
No specific RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals declarations are stated in the cited product information.