R5F10PLFKFB#V5 - 16-Bit RL78/F14 MCU, 96KB Flash | Renesas
MPN: R5F10PLFKFB#V5 ✓ 啟用中R5F10PLFKFB#V5 概覽
A microcontroller is a programmable system-on-chip that integrates a CPU core, non-volatile program memory, data memory, timers, serial peripherals and analog blocks on a single die. The Renesas RL78 series is positioned as a low-power, code-efficient 16-bit architecture for cost-sensitive embedded control. The RL78/F14 group sits at the upper level of the RL78 family, spanning 30-pin to 100-pin devices with 48 KB to 256 KB of flash, and extends the base RL78 feature set with communications and motor-control peripherals.
Headline features of the R5F10PLFKFB#V5 include 96 KB of on-chip flash for application code, integrated CAN and LIN interfaces for in-vehicle or distributed serial networking, dedicated BLDC motor control support using Timer RD and comparator resources, and functional safety features that assist system-level diagnostics. The wide 3.3 V / 5 V operating supply range allows the same device to sit between a 3.3 V sensor domain and a 5 V actuator domain without level translation.
Internally, the device is built around the RL78 16-bit CISC core, which uses a compact instruction set that reduces code density requirements relative to generic 8-bit controllers. That efficiency, combined with the family's low current consumption in sleep and stop modes, makes the part attractive for systems that spend most of their lifetime in a low-power state and only wake periodically to acquire data or drive an actuator. The 64-pin LQFP footprint exposes the full set of general-purpose I/O, timer channels, serial functions and analog inputs required for multi-channel control boards.
Typical deployments include automotive body control units, CAN-to-LIN gateway modules, electric pump and fan controllers, battery-powered sensing nodes, and compact appliance control boards. Because the CAN and LIN modules are on-die, a single R5F10PLFKFB#V5 can terminate a mixed vehicle network segment without external transceivers or a companion communication IC.
When laying out the board, treat the 64-pin LQFP as a fine-pitch land pattern with dedicated ground pins distributed around the perimeter; route the CAN and LIN lines as controlled-impedance, short traces terminated per the bus topology, and keep switching or high-current paths away from the analog and timer inputs. Confirm the exact pin assignment and peripheral multiplexing in the manufacturer pin list before finalising the schematic.
直接替換替代品,適用於 R5F10PLFKFB#V5 — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
R5F10PLFKFB#X5
✅ 直接替換📋 參考替代品(不在目錄中)
R5F10PLJKFB
✅ 直接替換📋 參考替代品(不在目錄中)
R5F10PLJLFB#V5
✅ 直接替換📋 參考替代品(不在目錄中)
R5F10PLHLFB#V5
✅ 直接替換📋 參考替代品(不在目錄中)
R5F10PLFKFB#V5 最大額定值與電氣特性
| Device Type | 16-bit CISC microcontroller (MCU) |
| Series / Family | RL78/F14 |
| Core Architecture | RL78 16-bit CISC |
| Flash Memory (Program) | 96 KB |
| 工作電源電壓 | 3.3 V / 5 V |
| 封裝 | 64-pin LQFP |
| 腳位數 | 64 pins |
| 安裝類型 | Surface mount |
| Automotive CAN Module | Built-in CAN module |
| Automotive LIN Module | Built-in LIN module |
| BLDC Motor Control | Supported (Timer RD + comparator resources) |
| Advanced Timer | Timer RD |
| Analog Comparator | Comparator peripheral included |
| Functional Safety Features | Supported for BLDC motor control systems |
| Family Flash Memory Range | 48 KB to 256 KB across RL78/F14 lineup |
| Family Pin Count Range | 30 pins to 100 pins across RL78/F14 lineup |
R5F10PLFKFB#V5 64-pin lqfp 腳位配置指南
R5F10PLFKFB#V5(64-pin lqfp 封裝)的腳位配置。 此數位 IC 包含 GPIO、通訊介面(UART、SPI、I2C)與電源腳位。替代腳位功能與配置選項請參閱製造商資料表。對嵌入式系統設計與 PCB 佈局至關重要。
無詳細腳位定義資料: R5F10PLFKFB#V5.
請參閱 資料表 以查看完整腳位配置。
典型應用
R5F10PLFKFB#V5 適用於 6 應用s: Automotive Body Control Module, CAN to LIN Gateway Module, BLDC Motor Control for Pumps and Fans, Industrial Sensor Node with Serial Bus, Battery-Powered Metering and Environmental Sensing, Appliance and Household Equipment Control.
Automotive Body Control Module
The R5F10PLFKFB#V5 suits body control modules where a central node aggregates door, lighting and wiper signals while talking to other ECUs. Its integrated CAN module handles the vehicle backbone without an external controller, and the integrated LIN module drives sub-buses for switches and actuators, cutting two peripheral bridges from the design. The 3.3 V / 5 V operating range lets one device supervise 3.3 V sensor inputs and 5 V driver outputs on the same board, and 96 KB of flash leaves room for diagnostic routines, gateway filtering and future firmware growth. The 64-pin LQFP exposes the I/O and timer channels needed for door lock and wiper pulse timing.
推薦
CAN to LIN Gateway Module
A CAN to LIN gateway is a direct match for the R5F10PLFKFB#V5 because both protocol controllers are on-die, so a single 64-pin LQFP device replaces a CAN controller, a LIN controller, their transceivers' companion logic and the bridging microcontroller typically used. The 16-bit CISC core handles message routing, ID mapping and periodic frame translation with a code density that keeps the firmware inside 96 KB of flash, while the comparator and timer resources support periodic wake-up of the LIN sub-network. The low consumption current of the RL78 family helps when the gateway is powered from a vehicle or 24 V industrial rail through a local regulator.
推薦
BLDC Motor Control for Pumps and Fans
The R5F10PLFKFB#V5 can drive a brushless DC motor directly using its Timer RD channels and comparator inputs for sensorless position detection, together with the functional safety features of the RL78/F14 family. This removes the external commutation logic and gate sequencing typically added around a generic MCU in compact pump, fan and e-bike drive-assist designs. The 3.3 V / 5 V supply flexibility lets the motor rail and the logic rail be regulated independently, and 96 KB of flash accommodates current control loops, fault handling and field update routines. The 64-pin LQFP provides the timer outputs, comparator inputs and digital I/O required for a multi-phase driver interface.
推薦
Industrial Sensor Node with Serial Bus
Low-power industrial sensor nodes benefit from the RL78 family's low consumption current, and the R5F10PLFKFB#V5 adds the CAN module needed to join a plant network without an external interface IC. The 16-bit core with 96 KB of flash can run a stack driver, calibration storage and local filtering alongside the measurement task, while Timer RD channels handle precise sampling intervals and the comparator provides fast threshold events. The 3.3 V / 5 V range suits retrofit boards that inherit either an existing sensor rail or a legacy 5 V loop supply, and the 64-pin LQFP leaves spare I/O for additional transducers.
推薦
Battery-Powered Metering and Environmental Sensing
For battery metering and environmental sensing terminals, the R5F10PLFKFB#V5 pairs wide code density with the family's low standby current, so a measurement cycle can run, report and then return to a low-power state without exhausting the cell. The integrated CAN or LIN interface removes the need for a radio co-processor in wired metering installations, and the 96 KB of flash holds a data logger, calibration tables and a bootloader. The comparator and timer resources support wake-up thresholds and periodic reporting cycles, while the 3.3 V / 5 V supply range permits direct operation from either a coin-cell regulator output or a 5 V bus.
推薦
Appliance and Household Equipment Control
Appliance control boards need a microcontroller with enough general-purpose I/O for relays, valves and displays, and the R5F10PLFKFB#V5 delivers that in a 64-pin LQFP with a small external component count. The 16-bit CISC core keeps the code compact enough for 96 KB of flash while running a state machine, keypad scan and motor or valve sequencer, and Timer RD channels provide the timing needed for agitator or compressor sequences. The LIN module lets the board talk to simple peripheral modules, and the 3.3 V / 5 V supply tolerance simplifies interfacing to a mixed control and drive section of a main board.
推薦
推薦產品摘要
工程參考資料,適用於 R5F10PLFKFB#V5 — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | R5F10PLFKFB#X5 | R5F10PLJKFB | R5F10PLJLFB#V5 | R5F10PLHLFB#V5 |
|---|---|---|---|---|---|
| Package | 64-pin LQFP | 64-pin LQFP - same | 64-pin LQFP - same | 64-pin LQFP - same | 64-pin LQFP - same |
| Brand | Renesas Electronics | Renesas Electronics | Renesas Electronics | Renesas Electronics | Renesas Electronics |
| Core Architecture | 16-bit CISC RL78 | 16-bit CISC RL78 | 16-bit CISC RL78 | 16-bit CISC RL78 | 16-bit CISC RL78 |
| Series / Family | RL78/F14 | RL78/F14 | RL78/F14 | RL78/F14 | RL78/F14 |
| Operating Supply Voltage | 3.3 V / 5 V | 3.3 V / 5 V | 3.3 V / 5 V | 3.3 V / 5 V | 3.3 V / 5 V |
| Integrated CAN Module | Yes | Yes | Yes | Yes | Yes |
| Integrated LIN Module | Yes | Yes | Yes | Yes | Yes |
| BLDC Motor Control Support | Yes (Timer RD and comparator resources) | Yes | Yes | Yes | Yes |
主要差異化特點
- Largest code budget among the listed 64-pin LQFP RL78/F14 candidates (對比R5F10PLJLFB#V5)
- Two on-die serial network controllers in a single MCU (對比R5F10PLHLFB#V5)
- Drop-in same-die alternative for temperature-grade changes (對比R5F10PLFKFB#X5)
設計說明
Place the 64-pin LQFP so that the CAN and LIN routes leave the device directly toward the connector or transceiver, keeping those traces short and away from timer outputs and comparator inputs. Both buses are single-ended and sensitive to radiated and conducted noise, so keep the ground return path under the bus pair and avoid routing them beneath switching regulators or motor driver stages. Firmware should enable the CAN and LIN module only after the rails have settled, which prevents a partially powered peripheral from driving a floating bus during start-up.
The R5F10PLFKFB#V5 accepts 3.3 V or 5 V, so confirm which rail is present at the power pins before finalising the regulator choice. Because the RL78 family is designed for low consumption current, the regulator budget is dominated by the peak load seen during analog conversion and timer activity rather than by the standby figure, so size the supply for the worst-case active transient and keep a low-impedance reservoir close to the supply pins. Add bulk and high-frequency decoupling at the supply entry to keep switching ripple out of the comparator and timer inputs.
A frequent error is treating the two ordering suffixes as interchangeable when they are not: the base device is the same, but the suffix selects the ambient temperature grade of the assembled part, and using the wrong grade can push the junction outside its rated range in a hot enclosure. The second common mistake is assuming the flash size carries over when moving to a smaller-code sibling such as the R5F10PLJLFB#V5, which will break the link if the firmware exceeds the new budget. Verify both the suffix and the linker map against the manufacturer datasheet before releasing the design to production.
合規資訊
The manufacturer describes the RL78/F14 as an automotive-interface family with built-in CAN and LIN modules, but no explicit RoHS, REACH, AEC-Q100 or lead-free statement was retrieved for this ordering code. Confirm the compliance and qualification entries in the Renesas product page and the applicable material declaration before releasing the BOM.