SI3211-E-GM - 38-QFN ProSLIC Telecom Interface | Skyworks
MPN: SI3211-E-GM ✗ 停產SI3211-E-GM 概覽
A subscriber line interface circuit, or SLIC, is the analog front end used to connect a telecommunications line to a digital voice codec. A ProSLIC integrates these traditionally separate functions into one low-voltage CMOS device. Within the semiconductor hierarchy, the SI3211-E-GM belongs to the telephone interface IC family, combining analog line driving, voice conversion, battery generation, and signaling control.
The SI3211-E-GM supports one telephone channel and features software-configurable internal ringing up to 90 VPK. Its telephone signaling capabilities include DTMF generation and decoding and Caller ID generation. These integrated functions reduce the need for separate line-interface circuitry while giving the host processor control over configurable line behavior.
The device operates from either 3.3 V or 5 V and has a typical supply current of 88 mA. A typical power consumption of 700 mW is specified for this operating condition. The exposed-pad QFN construction also provides a direct thermal path from the die to the PCB, allowing thermal performance to be managed through the ground-plane and copper area beneath the package.
Typical uses include analog telephone adapters, voice-over-IP terminal equipment, digital PBX line cards, Caller ID equipment, and other single-line telecom products. Its integration is especially useful when a compact design needs ringing, DTMF, Caller ID, voice conversion, and battery generation in one low-voltage package.
PCB design should follow the manufacturer’s pin and land-pattern instructions, with particular attention to the exposed pad and analog line connections. Decoupling capacitors should be placed close to their supply pins, while high-current and sensitive signal paths should use short, appropriately routed copper. Thermal review is necessary when the device operates near the maximum ambient temperature or inside a sealed terminal enclosure.
This page combines the manufacturer’s device description, package information, electrical characteristics, application guidance, sourcing structure, and verified replacement analysis. It also highlights where package, temperature-range, or regulatory differences can affect a substitution decision and helps engineers distinguish a true drop-in replacement from a merely related member of the Si321x family.
直接替換替代品,適用於 SI3211-E-GM — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
此產品無可直接替換的替代品。
申請替代品SI3211-E-GM 規格
| Device Type | ProSLIC Subscriber Line Interface Circuit and CODEC |
| Number of Channels | 1 channel |
| Supply Voltage Options | 3.3 V or 5 V |
| Typical Supply Current | 88 mA |
| Typical Power Consumption | 700 mW |
| Internal Ringing Voltage | Up to 90 VPK |
| Ringing Configuration | Software-configurable internal ringing |
| DTMF Support | Generation and decoding |
| Caller ID Support | Generation |
| Battery Generation | Integrated |
| Process Technology | Low-voltage CMOS |
| Package Type | 38-QFN with exposed pad |
| Package Dimensions | 5 x 7 mm |
| 腳位數 | 38 pins |
| 安裝類型 | Surface mount |
SI3211-E-GM 5 x 7 mm 腳位配置指南
SI3211-E-GM(5 x 7 mm 封裝)的腳位配置。 腳位編號、功能與連接圖定義於製造商資料手冊中。請參閱該手冊以取得確切的封裝尺寸與焊接指引。
無詳細腳位定義資料: SI3211-E-GM.
請參閱 資料表 以查看完整腳位配置。
典型應用
SI3211-E-GM 適用於 6 應用s: Voice-over-IP Telephone Adapter, Digital PBX Line Card, Analog Caller ID Terminal, Digital Add-On Telephone, Embedded Voice Messaging Gateway, Industrial Telephone Intercom.
Voice-over-IP Telephone Adapter
The SI3211-E-GM is suited to a single-line voice-over-IP adapter because it consolidates the analog subscriber line interface, voice codec, and battery-generation functions into one low-voltage CMOS device. Its 3.3 V or 5 V supply support accommodates common embedded telecom platforms, while software-configurable ringing up to 90 VPK reduces the need for a separate ringing circuit. DTMF generation and decoding plus Caller ID generation can be handled locally before voice samples reach the network processor, helping simplify firmware and board partitioning.
Digital PBX Line Card
A digital PBX line card can use the SI3211-E-GM as the per-channel analog termination and signaling device. The integrated codec creates a defined conversion boundary between the telephone line and the card’s digital voice engine, while the battery generator supports line-state control without a discrete battery supply. Operating from 3.3 V or 5 V gives designers flexibility when the line card includes processors with different rail requirements, and the exposed-pad QFN assists heat removal through the PCB.
Analog Caller ID Terminal
The SI3211-E-GM fits an analog Caller ID terminal because Caller ID generation is integrated with the SLIC, codec, and battery-generation circuitry. This consolidated arrangement lowers the number of separate analog interface blocks required for a compact telephone design. Software-configurable internal ringing up to 90 VPK supports programmable ring cadence and voltage behavior, while DTMF generation and decoding provides keypad signaling without a separate tone-processing package.
Digital Add-On Telephone
A digital add-on telephone can place the SI3211-E-GM at the line-facing end of the product, where the device manages the analog subscriber line, codec, and battery generation. The integrated architecture is valuable in tabletop and wall-mounted products where component count and board area matter. Its 3.3 V or 5 V operation allows alignment with the telephone’s digital and analog subcircuits, and DTMF handling provides a direct path for local keypad signaling.
Embedded Voice Messaging Gateway
The SI3211-E-GM can serve as the analog line interface within an embedded voice messaging gateway that connects one PSTN line to embedded voice-processing electronics. Combining the subscriber line interface and codec limits conversion boundaries and reduces external glue logic. The 90 VPK maximum internal ringing capability supports line ringing requirements, while Caller ID and DTMF functions give the gateway access to signaling that can be decoded or generated under host-software control.
Industrial Telephone Intercom
An industrial telephone intercom can use the SI3211-E-GM when the unit requires one analog line, integrated line power, ringing, and dial-tone signaling. The device’s 88 mA typical supply current and 700 mW typical consumption identify power handling as an important design consideration in compact embedded equipment. The exposed-pad QFN should be connected to the PCB thermal plane as directed by the manufacturer package information, with analog routing kept separate from sensitive processor and clock paths.
工程參考資料,適用於 SI3211-E-GM — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 |
|---|---|
| Package | 38-QFN with exposed pad, 5 x 7 mm |
| Brand | Skyworks Solutions Inc. |
| Product Type | ProSLIC subscriber line interface circuit and CODEC |
| Number of Channels | 1 channel |
| Supply Voltage | 3.3 V or 5 V |
| Typical Supply Current | 88 mA |
| Typical Power Consumption | 700 mW |
| Internal Ringing Capability | Software-configurable, up to 90 VPK |
| DTMF Functions | Generation and decoding |
| Caller ID Function | Generation |
主要差異化特點
- Comprehensive single-channel telephone interface integration (對比Discrete SLIC and codec implementation)
- Programmable high-voltage internal ringing (對比External ringing-generator architecture)
- Flexible low-voltage supply support (對比Single-rail-only interface design)
設計說明
Follow the manufacturer’s 38-QFN land-pattern and exposed-pad instructions exactly. Place input and output decoupling capacitors close to the corresponding device pins, keep the exposed-pad connection continuous with the intended thermal and ground plane, and avoid interrupting the return path beneath the package. These practices reduce supply disturbance and preserve the intended electrical and thermal behavior of the ProSLIC.
Separate the telephone-line and ringing paths from sensitive clock, audio, and digital signal paths where the board geometry allows. Use short return paths and a solid ground reference, and route high-voltage-capable ringing nodes carefully because the internal ringing feature can operate up to 90 VPK. Review isolation distances against the final product’s applicable telephone-interface safety requirements before releasing the layout.
The SI3211-E-GM has a typical power consumption of 700 mW under the stated operating condition. Estimated from that value, the device converts approximately 700 mW into heat at the nominal operating point. Provide copper area beneath the exposed pad and use the package thermal data to determine whether a dedicated heat-spreading pattern is needed, especially at elevated ambient temperature or in a sealed enclosure.
Do not assume that a related Si3211 suffix is automatically interchangeable. SI3211-E-FTR is documented in a 38-TSSOP package, while SI3211-E-GM uses a 38-QFN exposed-pad package. Confirm the ordering suffix, temperature grade, pin assignments, land pattern, and exposed-pad connection before substitution. A functional match does not remove the need for mechanical and pin-level verification.
合規資訊
The manufacturer datasheet excerpt identifies the device and its integrated telephone-interface functions but does not state the requested compliance classifications. No compliance status has been inferred.