Texas Instruments

SN75159D - Dual RS-422 Driver, 5 V, 14-SOIC | Texas Instruments

MPN: SN75159D ✓ 啟用中
5 V Vdss ANSI EIA/TIA-422-B Rds(on) 14-pin SOIC Package
MOQ: 1 |

SN75159D 概覽

Texas Instruments SN75159D is a dual differential line driver with 3-state outputs, a 5 V single-supply rating, and a 14-pin SOIC package. The device provides two balanced driver channels designed for RS-422 and related differential signaling systems. Its high-impedance output state supports party-line and shared-bus arrangements where multiple transmitters must be connected to the same physical line.

A differential line driver is a digital interface IC that converts a pair of complementary TTL-compatible logic signals into a balanced differential output. This signaling method reduces sensitivity to common-mode noise compared with single-ended transmission. The SN75159 family supports balanced point-to-point and multidrop interfaces associated with ANSI EIA/TIA-422-B and ITU Recommendation V.11 applications, as identified in the manufacturer documentation.

The principal features of the SN75159D are its dual-driver configuration, balanced differential outputs, 3-state output control, single 5 V supply operation, and TTL-compatible inputs. The 3-state behavior allows each driver channel to be disconnected electrically when inactive. This is useful in party-line systems because multiple transmitters can share a bus without preventing other channels from communicating when their output-enable controls are inactive.

The SN75159D is a line-driver rather than a line receiver. Data is driven from the logic side toward a balanced cable or board-level transmission path, while a separate receiver IC converts the differential signal back into logic levels at the destination. Using a transmitter and receiver that implement compatible RS-422 signaling helps maintain consistent voltage thresholds, impedance behavior, and common-mode limits across the link.

Typical uses include industrial data acquisition, test and measurement systems, communications equipment, instrumentation interfaces, computer peripherals, and other systems that transmit digital information over a balanced differential connection. Cable length, data rate, termination, grounding, and receiver selection remain system-level constraints. Differential routing should use a controlled impedance and a grounded reference where practical to preserve signal integrity.

When laying out a circuit using the SN75159D, place the device near the line-driver interface, keep the differential pair tightly matched, and provide a clear return path. Account for connector and cable reflections with the termination strategy recommended for the selected communication standard. Enable and disable sequencing should also ensure that only the intended transmitter drives the shared bus.

This page consolidates the SN75159D interface function, package information, sourcing workflow, application guidance, and engineering checks into a concise selection reference. It also identifies which device details still require confirmation from the manufacturer datasheet before a new layout is released for production.

直接替換替代品,適用於 SN75159D — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。

此產品無可直接替換的替代品。

申請替代品

SN75159D 規格

Product Type Dual differential line driver
Number of Driver Channels 2 channels
Output State 3-state outputs
供應電壓 5 V
Supported Interface RS-422
Input Compatibility TTL compatible
Line Operation Balanced
Standards Reference ANSI EIA/TIA-422-B
Communications Recommendation ITU Recommendation V.11
封裝 14-pin SOIC
安裝類型 Surface mount
High-Impedance Output Yes
Party-Line Support Yes

SN75159D 14-pin soic 腳位配置指南

SN75159D(14-pin soic 封裝)的腳位配置。 腳位編號、功能與連接圖定義於製造商資料手冊中。請參閱該手冊以取得確切的封裝尺寸與焊接指引。

SN75159D 的 14-pin soic 封裝腳位圖

無詳細腳位定義資料: SN75159D.

請參閱 資料表 以查看完整腳位配置。

典型應用

SN75159D 適用於 6 應用s: Industrial Data-Acquisition Systems, Balanced Test and Measurement Interfaces, Party-Line Communication Networks, Communications Equipment, Computer Peripherals and Data Links, Instrumentation and Control Panels.

🏭

Industrial Data-Acquisition Systems

The SN75159D suits measurement and control systems that must move digital commands or status signals over a balanced cable instead of a long single-ended path. Its two differential channels provide a practical way to connect a transmitter to a remote receiver while reducing sensitivity to common-mode voltage present in industrial environments. The device operates from one 5 V supply and accepts TTL-compatible inputs, allowing its outputs to be controlled by ordinary digital logic. Its 3-state outputs are valuable when several instrument modules can share a bus and only one transmitter should be active at a time. Confirm the data rate, cable length, connector, receiver, and termination against the complete interface specification.

🔧

Balanced Test and Measurement Interfaces

The SN75159D can provide the transmit side of a laboratory or industrial test system that distributes clock, command, or status signals over a balanced connection. Differential signaling is useful when the source and destination are separated by cable or when the enclosure environment contains significant electrical noise. Two driver channels allow the design to carry complementary functions on one 14-pin device, while the high-impedance output supports controlled sharing where applicable. The transmitter should be paired with a compatible RS-422 receiver and a termination arrangement selected from the actual line impedance, length, and operating data rate.

🌐

Party-Line Communication Networks

The SN75159D is appropriate for a party-line arrangement in which multiple locations share one balanced communication path and individual transmitters are enabled according to access control. Each of its two output channels can enter a high-impedance state when it is not selected, preventing an inactive driver from opposing the active transmitter. This behavior supports bus-oriented equipment without requiring a separate line driver for every source. Designers must ensure that only one transmitter is active at a time unless the system specification expressly supports another operating mode. Cable impedance, stub length, receiver loading, and termination still determine whether the physical bus meets its required data rate and signal integrity margin.

🌐

Communications Equipment

The SN75159D can serve as the balanced output stage in communications equipment that needs an RS-422-compatible transmitter rather than a single-ended logic output. Its dual channels support independent command and response paths, or two links sharing a common 5 V supply. TTL-compatible inputs simplify interfacing with digital control logic, and the high-impedance output allows controlled bus participation. A system-level RS-422 implementation also needs a compatible receiver, suitable connectors, cable routing with matched differential geometry, and termination that reflects the actual source and load impedances. The interface should be validated at the intended clock rate and maximum cable length.

🖥️

Computer Peripherals and Data Links

The SN75159D is useful in legacy or industrial peripheral interfaces that transmit digital data over a balanced differential connection. The 14-pin SOIC package is compatible with conventional surface-mount assembly, while two driver channels allow one transmitter package to support separate control and data paths. The 5 V supply operation and TTL-compatible inputs align with many digital systems. Because this device transmits rather than receives, the peripheral design must include an appropriate differential receiver and define how the unused transmitter channels are enabled. Review timing, output drive, common-mode range, and thermal conditions in the manufacturer documentation before treating it as a universal RS-422 transmitter.

🏭

Instrumentation and Control Panels

The SN75159D fits instrumentation panels and distributed control modules where command or alarm signals must cross a cable between equipment sections. Balanced differential outputs help preserve data integrity when the two ends of the link have different ground potentials or when conducted interference is present. The device's three-state outputs permit disciplined bus access, and its two channels can serve independent control functions. Engineering validation should include receiver compatibility, input thresholds, propagation timing, maximum load, and cable termination. Panel layouts should keep the balanced pair together and provide an appropriate reference return, especially where long cable runs cross noisy systems.

What is the SN75159D?
The SN75159D is a Texas Instruments dual differential line driver with two balanced transmitter channels and 3-state outputs. According to the manufacturer product page, the SN75159 family is designed for RS-422 interfaces and operates from a single 5 V supply. The SN75159D orderable configuration uses a 14-pin SOIC package, making it suitable for conventional surface-mount PCB assembly and balanced digital-interface designs.
Where can I download the SN75159D datasheet PDF?
The official SN75159D documentation begins at the Texas Instruments SN75159 product page, which links to the manufacturer datasheet and ordering information. The device is described there as a dual differential line driver with 3-state outputs. Use the pin-description table and electrical-characteristics tables in that document when assigning PCB functions, checking voltage limits, and confirming propagation timing before releasing a production design.
Where can I find the SN75159D pinout?
The SN75159D pin assignment is defined by the pin-description table in the Texas Instruments SN75159 manufacturer documentation. The verified package information identifies the SN75159D as a 14-pin SOIC device. Because the complete numbered pin list is not present in the accessible product excerpts, use the manufacturer pin table rather than inferring connections from a generic RS-422 symbol or another suffix of the SN75159 family.
How many driver channels does the SN75159D contain?
The SN75159D contains two differential driver channels, so one device can provide two balanced transmitter outputs. Each channel combines a complementary logic input with a three-state output stage. According to the Texas Instruments product description, the outputs support a high-impedance state for party-line systems in which more than one transmitter may be attached to the same balanced line.
What interface standard does the SN75159D support?
The SN75159D is intended for ANSI EIA/TIA-422-B and ITU Recommendation V.11 balanced differential signaling. Its documentation also identifies support for single 5 V supply operation, TTL-compatible inputs, and a high-impedance output state for party-line use. These features position the device as the transmitting element in an RS-422 link; a compatible differential receiver is still required at the far end.
What can replace the SN75159D?
The SN75159D must be replaced with a 14-pin SOIC dual differential driver that preserves its pin functions, 5 V operation, logic thresholds, 3-state control, and RS-422 output characteristics. The accessible cross-reference results do not identify a specific manufacturer-confirmed drop-in replacement, so no candidate is presented as a drop-in alternative. Validate any proposed substitute against the complete pinout, timing, output-current, and electrical-characteristic tables before using it in an existing layout.
What is the best cross-brand equivalent for the SN75159D?
No cross-brand equivalent can be identified as a verified drop-in replacement for the SN75159D from the available cross-reference information. A valid replacement must use the same 14-pin SOIC footprint and preserve the differential-output and 3-state functions. Review the manufacturer datasheets for voltage thresholds, propagation delay, output current, enable polarity, and power consumption rather than treating a functionally similar driver as automatically pin-compatible.
When should I choose the SN75159D for an RS-422 interface?
Choose the SN75159D when a design needs two balanced differential transmitter channels from a single 5 V supply and benefits from a high-impedance output state for shared or party-line wiring. It is most appropriate when the destination uses a compatible RS-422 receiver and the cable, termination, grounding, and data-rate requirements can be met. The transmitter alone does not complete the link, so receiver and connector selection remain part of the interface design.
Is the SN75159D suitable for industrial data acquisition?
The SN75159D is suitable for differential digital transmission in industrial data-acquisition equipment when the interface operates in accordance with RS-422 limits. Its balanced outputs, TTL-compatible inputs, 3-state capability, and 5 V supply support practical multi-driver instrumentation arrangements. Confirm the operating temperature, supply tolerance, output loading, and timing margins against the manufacturer ratings before using it in a temperature- or safety-critical installation.
How do I design the differential traces for an SN75159D board?
Route the two conductors of each differential pair together with matched spacing and geometry so they experience nearly identical propagation delay and attenuation. Provide a continuous reference plane, minimize stubs, and keep the interface section free of unnecessary test pads and branch traces. The manufacturer documentation should be consulted for output impedance, logic thresholds, and timing; those values determine whether additional source or termination components are needed.
Does the SN75159D need external line termination?
The SN75159D may require external termination when the selected RS-422 topology, cable length, and data rate produce reflections. Termination value and placement depend on the driver impedance, receiver impedance, connector, cable, and transmission rate rather than on the MPN alone. Use the termination scheme described for the complete interface, and account for whether multiple drivers are simultaneously active or only one transmitter is enabled.
What is the difference between a line driver and a line receiver?
A line driver converts logic-level inputs into a balanced differential signal for transmission, while a line receiver converts a differential signal back into logic levels. The SN75159D performs the driver function and provides two channels with 3-state outputs. A receiver is required at the destination, and the two devices should use compatible thresholds, common-mode limits, timing characteristics, and termination arrangements.
Is the SN75159D in stock, and what is its lead time?
Current stock, lot availability, and lead time should be requested through the Request a Quote form on this page. The product listings establish the SN75159D identity and 14-pin SOIC configuration, but they do not provide a qualifying quantity-break table or a confirmed current inventory commitment. For production planning, request the exact MPN, quantity, packaging form, date code, and any required traceability information through that form.
What is the price of the SN75159D?
Use the Request a Quote form on this page for a current SN75159D quotation. The accessible listings do not print a qualifying quantity-break price for the exact MPN, so no price figure is asserted. A complete quotation should confirm unit pricing, minimum order quantity, stock position, expected lead time, and whether the order will ship as a tube or another permitted shipping form.
What are the key specifications of SN75159D that engineers should know?
The SN75159D is a 5 V, dual differential line driver in a 14-pin SOIC package, with 3-state outputs, TTL-compatible inputs, balanced operation, and support for ANSI EIA/TIA-422-B and ITU Recommendation V.11 signaling. According to the Texas Instruments product page, its high-impedance output state supports party-line arrangements. Exact propagation delay, current limits, temperature range, and logic thresholds require confirmation in the manufacturer datasheet.

工程參考資料,適用於 SN75159D — 比較、設計指引及合規資訊。

選型指南

Choose the SN75159D when the design requires two balanced differential transmitter channels, a single 5 V supply, TTL-compatible control inputs, and a high-impedance state for shared-bus operation. It is particularly appropriate for RS-422 systems where the cable topology, receiver, and termination have already been designed around a compatible dual line driver. Do not select it as a receiver or for a single-ended TTL interface. Before committing to a replacement, require the same 14-pin SOIC footprint, matching enable polarity, compatible logic thresholds, equivalent propagation timing, and adequate output-current capability. The available cross-reference information does not confirm a specific drop-in substitute, so the SN75159D should remain the baseline unless a candidate is validated against the complete manufacturer datasheet and the existing PCB layout.

與替代品比較

參數 本產品
Product Type Dual differential line driver
Driver Channels 2
Package 14-pin SOIC
Brand Texas Instruments
Supply Voltage 5 V
Interface RS-422
Output State 3-state
Input Compatibility TTL compatible
Line Configuration Balanced
Party-Line Operation Supported through high-impedance outputs

主要差異化特點

  • Two differential transmitter channels in one package (對比SN75159D)
  • Three-state output capability for party-line use (對比SN75159D)
  • Single 5 V operation with TTL-compatible inputs (對比SN75159D)

設計說明

Route each differential output pair as a matched pair with consistent spacing and a continuous reference plane. Minimize stubs, connector branches, and test-pad discontinuities that can create impedance shifts or reflections. Keep the interface section compact and transition to the external cable through a connector appropriate for the selected RS-422 topology. The accessible product information does not provide the complete electrical tables or a numbered pin map, so use the manufacturer documentation for final pin assignment and trace geometry.

Do not allow two enabled transmitters to actively drive the same balanced node unless the interface specification explicitly permits that condition. The SN75159D's high-impedance state is intended for inactive party-line drivers; it does not remove the need for correct enable sequencing. Review the enable polarity and timing in the manufacturer pin and timing tables before defining control logic, and include a startup state that keeps every transmitter disabled until the intended channel is valid.

Select termination from the complete transmission path rather than applying it automatically. Cable attenuation, connector geometry, receiver loading, data rate, and whether multiple transmitter stubs are present all affect the correct termination strategy. Validate differential voltage and timing at the receiver with the longest intended cable and representative loading. If reflections or excessive loading appear, investigate source and load impedance, stub length, topology, and reference-plane continuity before changing logic levels.

合規資訊

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
無鉛
Unknown
無鹵
Unknown
衝突礦產
Unknown

Compliance status was not stated in the accessible manufacturer and distributor excerpts. Verify RoHS, REACH, automotive qualification, lead-free, halogen-free, and conflict-minerals status using the current manufacturer product documentation before procurement.

資料驗證日期: 2026-11-09 — 資料由 XAIPART 元件工程團隊驗證及整理

相關搜尋

SN75159D datasheet SN75159D pinout SN75159D datasheet pdf SN75159D equivalent SN75159D replacement SN75159D cross reference SN75159D footprint SN75159D application circuit SN75159D price SN75159D stock Texas Instruments SN75159D SN75159D RS-422 driver SN75159D 14-SOIC SN75159D 5 V line driver

相關元件與詞彙

Texas Instruments SN75159D SN75159 dual differential line driver RS-422 RS-422 interface IC differential line driver balanced line 3-state output high-impedance output party-line communication TTL-compatible input 5 V power supply ANSI EIA/TIA-422-B ITU Recommendation V.11 SOIC-14 surface-mount package industrial data acquisition test and measurement communications equipment signal integrity differential pair line termination
快速報價 RFQ
請填寫完整詳細資料 — 我們的業務團隊將於 24 小時內回覆
料號 製造商 封裝 QTY 目標價格 小計
✓
報價已提交!

我們將於 24 小時內回覆您的電子郵件

1
詢價已提交
2
已收到報價
3
已下單
4
付款
5
已出貨
6
已送達
檢視詢價單詳情