SN75159D - Dual RS-422 Driver, 5 V, 14-SOIC | Texas Instruments
MPN: SN75159D ✓ פעילSN75159D סקירה
A differential line driver is a digital interface IC that converts a pair of complementary TTL-compatible logic signals into a balanced differential output. This signaling method reduces sensitivity to common-mode noise compared with single-ended transmission. The SN75159 family supports balanced point-to-point and multidrop interfaces associated with ANSI EIA/TIA-422-B and ITU Recommendation V.11 applications, as identified in the manufacturer documentation.
The principal features of the SN75159D are its dual-driver configuration, balanced differential outputs, 3-state output control, single 5 V supply operation, and TTL-compatible inputs. The 3-state behavior allows each driver channel to be disconnected electrically when inactive. This is useful in party-line systems because multiple transmitters can share a bus without preventing other channels from communicating when their output-enable controls are inactive.
The SN75159D is a line-driver rather than a line receiver. Data is driven from the logic side toward a balanced cable or board-level transmission path, while a separate receiver IC converts the differential signal back into logic levels at the destination. Using a transmitter and receiver that implement compatible RS-422 signaling helps maintain consistent voltage thresholds, impedance behavior, and common-mode limits across the link.
Typical uses include industrial data acquisition, test and measurement systems, communications equipment, instrumentation interfaces, computer peripherals, and other systems that transmit digital information over a balanced differential connection. Cable length, data rate, termination, grounding, and receiver selection remain system-level constraints. Differential routing should use a controlled impedance and a grounded reference where practical to preserve signal integrity.
When laying out a circuit using the SN75159D, place the device near the line-driver interface, keep the differential pair tightly matched, and provide a clear return path. Account for connector and cable reflections with the termination strategy recommended for the selected communication standard. Enable and disable sequencing should also ensure that only the intended transmitter drives the shared bus.
This page consolidates the SN75159D interface function, package information, sourcing workflow, application guidance, and engineering checks into a concise selection reference. It also identifies which device details still require confirmation from the manufacturer datasheet before a new layout is released for production.
חלופות תחליף ישיר עבור SN75159D — אותו מארז, תואם פין-לפין. חלקים במארז שונה הדורשים עיבוד מחדש של ה-PCB אינם נכללים.
אין חלופות תואמות Drop-in עבור מוצר זה.
בקשת חלופותSN75159D מפרטים
| Product Type | Dual differential line driver |
| Number of Driver Channels | 2 channels |
| Output State | 3-state outputs |
| מתח אספקה | 5 V |
| Supported Interface | RS-422 |
| Input Compatibility | TTL compatible |
| Line Operation | Balanced |
| Standards Reference | ANSI EIA/TIA-422-B |
| Communications Recommendation | ITU Recommendation V.11 |
| מארז | 14-pin SOIC |
| סוג הרכבה | Surface mount |
| High-Impedance Output | Yes |
| Party-Line Support | Yes |
מדריך תצורת פינים של SN75159D 14-pin soic
תצורת פינים עבור SN75159D (מארזת 14-pin soic). מספרי פינים, פונקציות ותרשימי חיבורים מוגדרים ב-Datasheet של היצרן. יש לעיין בו לקבלת ה-footprint המדויק והנחיות הלחמה.
אין נתוני פריסת פינים מפורטים עבור SN75159D.
עיינו ב- גיליון נתונים עבור תצורת פינים מלאה.
יישומים טיפוסיים
SN75159D מתאים עבור 6 יישוםs: Industrial Data-Acquisition Systems, Balanced Test and Measurement Interfaces, Party-Line Communication Networks, Communications Equipment, Computer Peripherals and Data Links, Instrumentation and Control Panels.
Industrial Data-Acquisition Systems
The SN75159D suits measurement and control systems that must move digital commands or status signals over a balanced cable instead of a long single-ended path. Its two differential channels provide a practical way to connect a transmitter to a remote receiver while reducing sensitivity to common-mode voltage present in industrial environments. The device operates from one 5 V supply and accepts TTL-compatible inputs, allowing its outputs to be controlled by ordinary digital logic. Its 3-state outputs are valuable when several instrument modules can share a bus and only one transmitter should be active at a time. Confirm the data rate, cable length, connector, receiver, and termination against the complete interface specification.
מומלץ
Balanced Test and Measurement Interfaces
The SN75159D can provide the transmit side of a laboratory or industrial test system that distributes clock, command, or status signals over a balanced connection. Differential signaling is useful when the source and destination are separated by cable or when the enclosure environment contains significant electrical noise. Two driver channels allow the design to carry complementary functions on one 14-pin device, while the high-impedance output supports controlled sharing where applicable. The transmitter should be paired with a compatible RS-422 receiver and a termination arrangement selected from the actual line impedance, length, and operating data rate.
מומלץ
Party-Line Communication Networks
The SN75159D is appropriate for a party-line arrangement in which multiple locations share one balanced communication path and individual transmitters are enabled according to access control. Each of its two output channels can enter a high-impedance state when it is not selected, preventing an inactive driver from opposing the active transmitter. This behavior supports bus-oriented equipment without requiring a separate line driver for every source. Designers must ensure that only one transmitter is active at a time unless the system specification expressly supports another operating mode. Cable impedance, stub length, receiver loading, and termination still determine whether the physical bus meets its required data rate and signal integrity margin.
מומלץ
Communications Equipment
The SN75159D can serve as the balanced output stage in communications equipment that needs an RS-422-compatible transmitter rather than a single-ended logic output. Its dual channels support independent command and response paths, or two links sharing a common 5 V supply. TTL-compatible inputs simplify interfacing with digital control logic, and the high-impedance output allows controlled bus participation. A system-level RS-422 implementation also needs a compatible receiver, suitable connectors, cable routing with matched differential geometry, and termination that reflects the actual source and load impedances. The interface should be validated at the intended clock rate and maximum cable length.
מומלץ
Computer Peripherals and Data Links
The SN75159D is useful in legacy or industrial peripheral interfaces that transmit digital data over a balanced differential connection. The 14-pin SOIC package is compatible with conventional surface-mount assembly, while two driver channels allow one transmitter package to support separate control and data paths. The 5 V supply operation and TTL-compatible inputs align with many digital systems. Because this device transmits rather than receives, the peripheral design must include an appropriate differential receiver and define how the unused transmitter channels are enabled. Review timing, output drive, common-mode range, and thermal conditions in the manufacturer documentation before treating it as a universal RS-422 transmitter.
מומלץ
Instrumentation and Control Panels
The SN75159D fits instrumentation panels and distributed control modules where command or alarm signals must cross a cable between equipment sections. Balanced differential outputs help preserve data integrity when the two ends of the link have different ground potentials or when conducted interference is present. The device's three-state outputs permit disciplined bus access, and its two channels can serve independent control functions. Engineering validation should include receiver compatibility, input thresholds, propagation timing, maximum load, and cable termination. Panel layouts should keep the balanced pair together and provide an appropriate reference return, especially where long cable runs cross noisy systems.
מומלץ
נתוני עזר הנדסיים עבור SN75159D — השוואה, הנחיות תכנון ומידע על תאימות.
מדריך בחירה
השוואה עם חלופות
| פרמטר | מוצר זה |
|---|---|
| Product Type | Dual differential line driver |
| Driver Channels | 2 |
| Package | 14-pin SOIC |
| Brand | Texas Instruments |
| Supply Voltage | 5 V |
| Interface | RS-422 |
| Output State | 3-state |
| Input Compatibility | TTL compatible |
| Line Configuration | Balanced |
| Party-Line Operation | Supported through high-impedance outputs |
מבדילים עיקריים
- Two differential transmitter channels in one package (לעומתSN75159D)
- Three-state output capability for party-line use (לעומתSN75159D)
- Single 5 V operation with TTL-compatible inputs (לעומתSN75159D)
הערות תכנון
Route each differential output pair as a matched pair with consistent spacing and a continuous reference plane. Minimize stubs, connector branches, and test-pad discontinuities that can create impedance shifts or reflections. Keep the interface section compact and transition to the external cable through a connector appropriate for the selected RS-422 topology. The accessible product information does not provide the complete electrical tables or a numbered pin map, so use the manufacturer documentation for final pin assignment and trace geometry.
Do not allow two enabled transmitters to actively drive the same balanced node unless the interface specification explicitly permits that condition. The SN75159D's high-impedance state is intended for inactive party-line drivers; it does not remove the need for correct enable sequencing. Review the enable polarity and timing in the manufacturer pin and timing tables before defining control logic, and include a startup state that keeps every transmitter disabled until the intended channel is valid.
Select termination from the complete transmission path rather than applying it automatically. Cable attenuation, connector geometry, receiver loading, data rate, and whether multiple transmitter stubs are present all affect the correct termination strategy. Validate differential voltage and timing at the receiver with the longest intended cable and representative loading. If reflections or excessive loading appear, investigate source and load impedance, stub length, topology, and reference-plane continuity before changing logic levels.
מידע על תאימות
Compliance status was not stated in the accessible manufacturer and distributor excerpts. Verify RoHS, REACH, automotive qualification, lead-free, halogen-free, and conflict-minerals status using the current manufacturer product documentation before procurement.