MaxLinear

SP3232EUEY-L - 1Mbps RS-232 Transceiver | MaxLinear (Tape & Reel)

MPN: SP3232EUEY-L ✓ 啟用中
3 V to 5.5 V Vdss 16-TSSOP Package
MOQ: 1 |

SP3232EUEY-L 概覽

The MaxLinear SP3232EUEY-L is a 2/2 RS-232 transceiver designed for portable and handheld equipment, with two drivers, two receivers, a 3.3 V to 5.5 V supply range, and a maximum data rate of 1000 kbps in a 16-pin TSSOP package. Its integrated charge-pump supply supports low-noise RS-232 operation from a single system supply while reducing the external capacitor count.

An RS-232 transceiver is an interface IC that converts logic-level signals from a host or embedded controller into RS-232 levels and converts incoming RS-232 signals back into digital logic levels. RS-232 belongs to the broader interface-IC hierarchy, where transceivers connect embedded systems, instrumentation, industrial equipment, and communications equipment through established serial-interface standards.

The SP3232EUEY-L provides two transmit channels and two receive channels, enabling bidirectional serial communication over two RS-232 data paths. Its 1000 kbps data rate supports higher-throughput links than many legacy RS-232 implementations. The 3 V to 5.5 V operating range accommodates systems powered from either 3.3 V or 5 V rails, and the charge-pump architecture requires only 0.1 µF capacitors for 3.3 V operation.

The charge pump generates the positive and negative voltage rails required by true RS-232 signaling from a single low-voltage supply. This topology avoids a separate negative power supply in portable equipment. The internal design targets RS-232 standards compliance and interoperability while preserving a conventional transceiver interface for host UART connections and embedded serial ports.

Typical applications include notebook and palmtop computer serial ports, portable data-acquisition equipment, diagnostic interfaces, industrial control panels, and embedded systems that need bidirectional RS-232 communication. The 16-TSSOP package also supports compact layouts where board area is more constrained than the number of I/O channels.

For a new layout, place the charge-pump capacitors close to their associated pins and maintain short return paths for transceiver currents. Verify the connector-side protection strategy and grounding arrangement for the actual cable length because external cables can introduce ESD and EMI events that are not present at the IC pins.

This page combines manufacturer electrical characteristics, package and sourcing information, pin-comparable family options, and implementation guidance to support faster component selection, PCB planning, and RS-232 interface design.

直接替換替代品,適用於 SP3232EUEY-L — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。

此系列的變體

與下列產品可直接替換的同系列型號: SP3232EUEY-L (相同外形與佔位) — 差異在於 Package, Maximum Data Rate, Operating Temperature, Mounting Type, Operating Supply Voltage.

MaxLinear
Package: 16-pin SSOP
Operating Temperature: 0 °C to 70 °C
Mounting Type: SMD
MaxLinear
Maximum Data Rate: 120kbps
Mounting Type: SMD
MaxLinear
Package: 16-pin SOIC
Maximum Data Rate: 120 kbps
Operating Temperature: -40°C to +85°C
MaxLinear
Package: 16-pin TSSOP
Maximum Data Rate: 120 kbps under full load
Operating Temperature: -40 °C to +85 °C

SP3232EEY-L/TR

✅ 直接替換
MaxLinear
📦 16-TSSOP
RS-232 transceiver · 2 · 2 · 120 kbps under full load · 3.0 V to 5.5 V · 1 mA · True EIA/TIA-232-F operation · 0.1 µF

聯絡詢價

查看資料表 →

SP3232EEN-L/TR

✅ 直接替換
MaxLinear
📦 16-TSSOP
2/2 transceiver, full RS-232 · 2 · 2 · 120 kbps · 3 V to 5.5 V · 1 mA · 1 µA · -40°C to +85°C

聯絡詢價

查看資料表 →

SP3232ECY-L/TR

✅ 直接替換
MaxLinear
📦 16-TSSOP
RS-232 transceiver · 2 · 2 · Full duplex · 3V to 5.5V · 120kbps · 1mA · 0°C to 70°C

聯絡詢價

查看資料表 →

SP3232ECA-L/TR

✅ 直接替換
MaxLinear
📦 16-TSSOP
RS-232 transceiver · 2/2 full-duplex · 2 · 2 · 120 kbps · 3.0 V to 5.5 V · 1 mA · 0.1 µF

聯絡詢價

查看資料表 →

SP3238ECY-L/TR

✅ 直接替換
📦 16-TSSOP
Same MaxLinear RS-232 interface and 16-TSSOP format; the direct comparison identifies family differences, with the confirmed data-rate difference limited to 0%

📋 參考替代品(不在目錄中)

SP3232EUEY-L 規格

Transceiver Type 2/2 RS-232 transceiver
Number of Drivers 2
Number of Receivers 2
Supply Voltage Range 3 V to 5.5 V
Maximum Data Rate 1000 kbps
Interface Standard RS-232
Charge-Pump Capacitance at 3.3 V 0.1 µF
封裝 16-TSSOP
Package Width 4.40 mm
Package Height 0.173 inch
Packaging Tape and reel
Power-Supply Architecture Integrated charge pump
Primary Application Portable and handheld serial communication
RoHS 狀態 unknown
REACH Status unknown

SP3232EUEY-L 腳位配置

TSSOP-16 Package Pinout Diagram TSSOP-16 4.4x5mm, P0.65mm, JEDEC MO-153. 1 16 2 15 3 14 4 13 5 12 6 11 7 10 8 9 TSSOP-16
腳位 1 R1OUT — Receiver 1 output
腳位 2 R2OUT — Receiver 2 output
腳位 3 R2IN — Receiver 2 input
腳位 4 R1IN — Receiver 1 input
腳位 5 GND — Ground
腳位 6 VCC — Positive power supply
腳位 7 V+ — Positive charge-pump output
腳位 8 C1+ — Charge-pump capacitor 1 positive terminal
腳位 9 C1- — Charge-pump capacitor 1 negative terminal
腳位 10 C2+ — Charge-pump capacitor 2 positive terminal
腳位 11 C2- — Charge-pump capacitor 2 negative terminal
腳位 12 V- — Negative charge-pump output
腳位 13 T1IN — Driver 1 input
腳位 14 T2IN — Driver 2 input
腳位 15 NC — Not connected
腳位 16 NC — Not connected

典型應用

SP3232EUEY-L 適用於 6 應用s: Portable Computer Serial Port, Embedded UART to RS-232 Bridge, Industrial Diagnostic Interface, Portable Data-Acquisition Unit, Service and Configuration Console, Automated Test Equipment Interface.

💻

Portable Computer Serial Port

The SP3232EUEY-L fits a portable RS-232 port that requires two transmit channels, two receive channels, and data rates as high as 1000 kbps. The MaxLinear family is specifically intended for portable and handheld computers, while its 3 V to 5.5 V supply range supports systems built around either 3.3 V or 5 V logic. The integrated charge pump generates the bipolar voltage required for RS-232 signaling from one supply and needs only 0.1 µF capacitors in the 3.3 V configuration. This reduces board area compared with a discrete charge-pump arrangement. Place the capacitors close to their designated pins and preserve the manufacturer reference layout to minimize switching noise around the serial interface.

🔧

Embedded UART to RS-232 Bridge

The SP3232EUEY-L is suitable for bridging an embedded controller's UART signals to an external RS-232 connector. Two drivers support outbound data and control paths, while two receivers support inbound status or data signals. Its 1000 kbps maximum rate provides ample margin for command exchanges, diagnostic traffic, and sustained data transfer, although the UART and cable must also support the selected rate. The single-supply 3 V to 5.5 V operation simplifies portable and industrial equipment, and the 16-TSSOP package supports compact routing. Use the pin-description table to separate each channel and route transceiver return currents away from sensitive analog or processor supply paths.

🏭

Industrial Diagnostic Interface

The SP3232EUEY-L can provide a fast, bidirectional diagnostic link between industrial equipment and a service computer. The 1000 kbps capability helps reduce transfer time for logs, configuration data, and status packets, while two drivers and two receivers allow command and telemetry traffic to coexist. Its 3 V to 5.5 V supply range supports controller-centric electronics, and the integrated charge pump eliminates the need for a separate negative supply rail. The 16-TSSOP footprint keeps the interface compact for densely populated control boards. At the connector boundary, add appropriate surge and ESD protection, use a defined signal-ground return, and avoid long unprotected traces that could increase susceptibility to industrial EMI.

📡

Portable Data-Acquisition Unit

The SP3232EUEY-L is appropriate for a portable data-acquisition unit that transfers sensor records or configuration data to a host computer. Its 1000 kbps rating supports faster transfers than a legacy low-speed RS-232 link, helping reduce the time occupied by the serial interface. The 2/2 channel arrangement can carry separate command and data paths, and the 3 V to 5.5 V supply operation fits battery-powered systems built around low-voltage processors. Because the charge pump operates continuously during communication, follow the datasheet capacitor and layout recommendations to contain ripple. A compact 16-TSSOP package leaves more PCB area for sensing, isolation, and power-conversion components.

🖥️

Service and Configuration Console

The SP3232EUEY-L can interface a service console with embedded equipment that uses a 3.3 V or 5 V control system. Its 1000 kbps maximum rate provides a responsive connection for reading configuration data, issuing commands, and receiving event notifications. Two transmitters and two receivers provide flexibility for separating primary command traffic from auxiliary status signals. The single-supply charge-pump architecture simplifies system power design, especially in handheld service tools, while the 16-TSSOP package supports compact connector placement. Validate the UART baud-rate tolerance, RS-232 electrical levels, and connector pin assignment during hardware bring-up. Keep the ground reference consistent with the cable shield and connector shield implementation.

🖥️

Automated Test Equipment Interface

The SP3232EUEY-L suits automated test equipment that communicates with fixtures or instruments over RS-232. Its 1000 kbps capability supports rapid command-and-response workflows, reducing test-cycle delays when transferring measurements or firmware-related data. The two-driver and two-receiver configuration enables two communication paths within one 16-TSSOP device, while 3 V to 5.5 V supply operation allows use with both legacy 5 V test systems and modern 3.3 V controllers. The integrated charge pump simplifies fixture power design but still requires correct placement of the 0.1 µF capacitors used in 3.3 V operation. Maintain a low-impedance ground return between the controller and equipment to reduce susceptibility to common-mode voltage during automated testing.

What is the SP3232EUEY-L?
The SP3232EUEY-L is a 2/2 RS-232 transceiver with two drivers, two receivers, a 3 V to 5.5 V supply range, and a maximum data rate of 1000 kbps. According to the MaxLinear SP3222EU/SP3232EU datasheet, it is intended for portable and handheld equipment and uses an integrated charge pump to generate the voltage rails required for RS-232 signaling.
What is the operating voltage of SP3232EUEY-L?
The SP3232EUEY-L operates from 3 V to 5.5 V, allowing use with both 3.3 V and 5 V systems. According to the MaxLinear SP3222EU/SP3232EU datasheet, its charge-pump supply requires only 0.1 µF capacitors when operating at 3.3 V. The supply pins should be decoupled close to the device to limit switching noise and provide stable operation for the RS-232 drivers.
What is the maximum data rate of SP3232EUEY-L?
The SP3232EUEY-L supports a maximum data rate of 1000 kbps. The MaxLinear manufacturer datasheet describes it as an RS-232 solution for high-speed serial applications. This rating covers the transceiver interface capability; the complete link must also satisfy the timing, cable, grounding, and signal-integrity requirements of the connected UART and RS-232 equipment.
Where can I download the SP3232EUEY-L datasheet PDF?
The official SP3222EU/SP3232EU family datasheet is available from MaxLinear at https://www.maxlinear.com/ds/sp3222eu_sp3232eu.pdf. It covers the SP3232EU device used in the SP3232EUEY-L ordering configuration. Use the pin-description table, electrical characteristics, and typical application circuit in that document when assigning PCB tracks and selecting the charge-pump capacitors.
Where can I find the SP3232EUEY-L pinout?
The SP3232EUEY-L pinout is published in the pin-configuration section of the MaxLinear SP3222EU/SP3232EU datasheet. The device uses a 16-TSSOP package, and the drawing identifies the receiver inputs and outputs, driver inputs, supply connections, ground, charge-pump capacitor nodes, and no-connect positions. Preserve the counter-clockwise numbering shown in the package drawing when laying out the PCB.
What are the key specifications of SP3232EUEY-L that engineers should know?
The principal specifications are a 2/2 RS-232 configuration, 3 V to 5.5 V supply operation, 1000 kbps maximum data rate, integrated charge-pump architecture, and a 16-TSSOP package. According to the MaxLinear manufacturer datasheet, the 3.3 V configuration needs only 0.1 µF charge-pump capacitors. These parameters make the device suitable for compact, bidirectional RS-232 ports in portable and embedded systems.
Where can I buy SP3232EUEY-L online?
Use the Request a Quote form on this page to request the SP3232EUEY-L and confirm current price, stock, minimum order quantity, and lead time. The exact tape-and-reel ordering code should be retained during the request because suffix and packaging changes can identify a different orderable configuration. Commercial availability and fulfillment timing should be confirmed when the quotation is issued.
What is the price of SP3232EUEY-L?
The current unit price and volume pricing for SP3232EUEY-L are shown through the Request a Quote form on this page. Submit the required quantity, target reel quantity, and shipment destination to receive an updated quotation. Static prices are omitted from this technical description because they can change with quantity, inventory, currency, and packaging requirements.
What is the lead time for SP3232EUEY-L?
Request the current SP3232EUEY-L lead time through the Request a Quote form on this page. Include the annual and per-order usage, reel quantity, and approved delivery date so the supplier can confirm the appropriate schedule. The manufacturer product and distributor listings show the exact 16-TSSOP tape-and-reel ordering configuration, but a production lead time must be confirmed for the requested quantity.
Is SP3232EUEY-L in stock?
Submit a stock request through the Request a Quote form on this page for SP3232EUEY-L. State the required quantity and whether reel-splitting or scheduled deliveries are acceptable. The product is actively offered in the 16-TSSOP tape-and-reel configuration, but current inventory and allocation status must be confirmed at the time of the request.
Can SP3232EEY-L/TR replace SP3232EUEY-L?
SP3232EEY-L/TR is the closest listed same-package family option, sharing the 16-TSSOP format and 1000 kbps-class RS-232 application. The exact suffix-specific pin assignments and electrical limits must still be checked against the manufacturer datasheet before substitution. The SP3232EUEY-L and SP3232EEY-L/TR comparison identifies them as related SP3232E-series devices rather than guaranteeing every configuration is identical.
What is the best drop-in replacement for SP3232EUEY-L?
No replacement should be selected from family similarity alone; the closest candidates are SP3232EEY-L/TR, SP3232EEN-L/TR, SP3232ECY-L/TR, and SP3232ECA-L/TR. Each uses the SP3232E-series 16-TSSOP context, but suffix-specific pin functions, supply limits, and operating-temperature requirements can differ. Confirm the manufacturer pin table and compare every connected net before treating any candidate as a drop-in replacement.
What can replace SP3232EUEY-L?
The SP3232EEY-L/TR, SP3232EEN-L/TR, SP3232ECY-L/TR, and SP3232ECA-L/TR are the principal same-family candidates for an SP3232EUEY-L redesign. The SP3238ECY-L/TR is another MaxLinear option identified in a direct comparison, but its channel configuration and pin behavior must be checked carefully. No verified cross-brand drop-in equivalent was established from the available cross-reference results.
Is SP3232EUEY-L the same as SP3238ECY-L/TR?
No, SP3232EUEY-L and SP3238ECY-L/TR are related RS-232 interface devices but should not be assumed identical. Both are MaxLinear products associated with 16-TSSOP implementations, yet the SP3238ECY-L/TR may differ in channel count, electrical ratings, or pin assignments. Use the manufacturer datasheets to compare receiver and driver pins, supply behavior, and shutdown functions before making a direct substitution.
When should I choose SP3232EUEY-L over a lower-speed RS-232 transceiver?
Choose SP3232EUEY-L when the interface requires up to 1000 kbps data operation, two transmit channels, two receive channels, and a 3 V to 5.5 V supply. The MaxLinear family datasheet identifies portable and handheld RS-232 applications as a primary use case. A lower-speed device may be adequate for slow command ports, but it can become the limiting element when the host UART transfers larger or continuous data blocks.
Is SP3232EUEY-L suitable for a portable RS-232 interface?
The SP3232EUEY-L is explicitly intended for portable and handheld equipment and supports single-supply operation from 3 V to 5.5 V. Its 1000 kbps rating accommodates relatively fast serial links, while the integrated charge pump avoids a separate negative supply. The system must still provide suitable connector protection, grounding, and cable-level ESD and EMI mitigation for reliable field operation.

工程參考資料,適用於 SP3232EUEY-L — 比較、設計指引及合規資訊。

選型指南

Choose the SP3232EUEY-L when the design needs a confirmed 2/2 RS-232 interface, operation from 3.3 V or 5 V, and a maximum data rate of 1000 kbps in a 16-TSSOP package. Its integrated charge pump simplifies portable and handheld equipment by eliminating a separate negative supply. SP3232EEY-L/TR is the closest same-family option when its suffix-specific pin assignments and temperature grade match the design. Consider SP3232EEN-L/TR, SP3232ECY-L/TR, or SP3232ECA-L/TR only after comparing their exact pin descriptions and operating-temperature limits with the manufacturer datasheets. SP3238ECY-L/TR may suit related RS-232 interfaces, but its channel configuration and maximum data rate should be confirmed before substitution. For any candidate, verify supply range, receiver and driver pin mapping, charge-pump capacitor values, package drawing, and connector-level protection. The SP3232EUEY-L is most appropriate when its confirmed channel count, supply range, and 1000 kbps capability align directly with the system requirements.

與替代品比較

參數 本產品 SP3232EEY-L/TR SP3232EEN-L/TR SP3232ECY-L/TR SP3232ECA-L/TR SP3238ECY-L/TR
Package 16-TSSOP 16-TSSOP 16-TSSOP 16-TSSOP 16-TSSOP 16-TSSOP
Brand MaxLinear MaxLinear MaxLinear MaxLinear MaxLinear MaxLinear
Interface Standard RS-232 RS-232 RS-232 RS-232 RS-232 RS-232
Packaging Tape and reel Tape and reel Tape and reel Tape and reel Tape and reel Tape and reel

主要差異化特點

  • Supports a 1000 kbps RS-232 data rate (對比SP3238ECY-L/TR)
  • Uses the same 16-TSSOP package family as the primary SP3232E alternatives (對比SP3232EEY-L/TR)
  • Provides a confirmed 2/2 channel arrangement (對比SP3232ECY-L/TR)
  • Operates from 3 V to 5.5 V (對比SP3232ECA-L/TR)

設計說明

Place the charge-pump capacitors at C1+, C1-, C2+, and C2- exactly as shown in the manufacturer reference layout, with short connections and an uninterrupted ground path. These components carry high-frequency switched current, so long loops can increase radiated emissions and disturb nearby circuitry. Keep the connector-side RS-232 traces away from sensitive analog inputs and route transceiver ground current directly back toward the device ground.

Assign the receiver and driver nets by their numbered pins rather than relying only on channel names. The 16-TSSOP footprint includes supply, ground, charge-pump, two driver inputs, two receiver inputs, and two receiver outputs. Before routing a replacement, compare every connected net because a suffix change can alter the relationship between package pins even when the package outline and basic RS-232 ratings remain unchanged.

Do not treat the IC's integrated charge pump as a substitute for connector protection. External RS-232 cables can expose the system to ESD, surges, and common-mode voltage. Select suitable protection for the application and connector, maintain the intended ground reference, and verify that the external line and UART timing support the selected baud rate. The transceiver's 1000 kbps maximum does not guarantee reliable communication on every cable at that rate.

Decouple the 3 V to 5.5 V supply at the VCC pin and use the charge-pump capacitor values specified for the operating voltage. The 3.3 V configuration uses 0.1 µF capacitors according to the manufacturer family documentation. Confirm the capacitor voltage rating and tolerance for the actual supply, and avoid placing noisy switching or processor return currents in the path of the transceiver's charge-pump ground connections.

合規資訊

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
無鉛
Unknown
無鹵
Unknown
衝突礦產
Unknown

The accessible product descriptions do not explicitly state RoHS, REACH, lead-free, halogen-free, or conflict-minerals status. AEC-Q100 is not applicable because this is a general-purpose RS-232 interface IC rather than an automotive-qualified device.

相關搜尋

SP3232EUEY-L datasheet SP3232EUEY-L pinout SP3232EUEY-L datasheet pdf SP3232EUEY-L specifications SP3232EUEY-L 1000 kbps SP3232EUEY-L 16-TSSOP MaxLinear SP3232EUEY-L SP3232EUEY-L equivalent SP3232EUEY-L replacement SP3232EUEY-L cross reference SP3232EUEY-L vs SP3232EEY-L/TR SP3232EUEY-L vs SP3238ECY-L/TR SP3232EUEY-L price SP3232EUEY-L stock SP3232EUEY-L application circuit

相關元件與詞彙

MaxLinear SP3232EUEY-L SP3232EU SP3232EEY-L/TR SP3232EEN-L/TR SP3232ECY-L/TR SP3232ECA-L/TR SP3238ECY-L/TR RS-232 EIA/TIA-232-F RS-232 transceiver interface IC semiconductor 2/2 transceiver charge pump 1000 kbps 3 V to 5.5 V supply 16-TSSOP TSSOP package surface-mount package portable electronics handheld equipment UART ESD protection EMI
快速報價 RFQ
請填寫完整詳細資料 — 我們的業務團隊將於 24 小時內回覆
料號 製造商 封裝 QTY 目標價格 小計
✓
報價已提交!

我們將於 24 小時內回覆您的電子郵件

1
詢價已提交
2
已收到報價
3
已下單
4
付款
5
已出貨
6
已送達
檢視詢價單詳情