TAS5100DAP - 30W Mono Class-D Audio | Texas Instruments
MPN: TAS5100DAP ✓ 啟用中TAS5100DAP 概覽
A Class-D power stage is a switching audio amplifier topology that controls current through the speaker output according to a pulse-width-modulated signal. Compared with a linear audio amplifier, this approach can achieve power efficiency above 90% into an 8-ohm load, reducing the amount of heat that must be removed from the audio output stage. The TAS5100DAP is a power-output-stage device intended for use with a preceding audio codec, DAC, DSP, or digital audio interface.
Key performance features include 30 W RMS output capability, 0.08% THD+N at 1 kHz into 6 ohms, 93 dB dynamic range in the TDAA system, and greater than 90% power efficiency into an 8-ohm load. Its digital input architecture supports direct reception of digital audio signals, avoiding an analog input stage and associated conversion circuitry in systems where a digital audio source is already available.
The 32-pin HTSSOP package provides a compact surface-mount solution with a PowerPAD for heat dissipation. The commercial temperature range extends from 0°C to 70°C. Because a 30 W output stage can dissipate substantial heat at low supply voltages or into low-impedance speakers, PCB copper area, thermal via layout, and the selected speaker load must be evaluated during system design.
Typical applications include home-theater and multimedia speaker amplification, powered speaker designs, digital audio receiver output stages, compact consumer audio products, and industrial audio systems using a digital signal-processing front end. The device is particularly suitable when low idle dissipation, high conversion efficiency, and direct digital audio control are priorities.
The main design tradeoff is power dissipation at low supply headroom. Output power is constrained by both supply voltage, speaker impedance, and thermal conditions; a nominal 30 W capability does not guarantee 30 W continuously at every input voltage or ambient temperature. Use the manufacturer powerPAD layout guidance and thermal calculations to establish dependable operating limits.
This product page consolidates the principal electrical characteristics, verified package information, application guidance, thermal considerations, and comparison criteria for the TAS5100DAP. It also distinguishes verified drop-in replacements from merely similar devices so engineers can make a footprint-compatible sourcing decision without changing the PCB.
直接替換替代品,適用於 TAS5100DAP — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
TAS5100DCA
✅ 直接替換 ⚠️ 規格未經驗證📋 參考替代品(不在目錄中)
TAS5100DAP 最大額定值與電氣特性
| Product Type | Digital audio power output stage |
| Amplifier Type | Class-D |
| Channel Configuration | 1 channel mono |
| Maximum Output Power | 30 W RMS |
| Dynamic Range | 93 dB in TDAA system |
| Total Harmonic Distortion plus Noise | 0.08% at 1 kHz and 30 W RMS into 6 ohm |
| Power Efficiency | >90% into 8 ohm load |
| 封裝 | 32-pin HTSSOP with PowerPAD |
| Number of Terminals | 32 terminals |
| Package Shape | Rectangular gull-wing |
| 安裝類型 | Surface mount |
| Temperature Grade | Commercial |
| 工作溫度範圍 | 0°C to 70°C |
| Output Load | 6 ohm and 8 ohm loads |
| Audio Input | Digital audio input |
TAS5100DAP rectangular gull-wing 腳位配置指南
TAS5100DAP(rectangular gull-wing 封裝)的腳位配置。 此類比元件具有輸入、輸出與電源腳位。偏移歸零、補償與致能腳位配置請參閱製造商資料表。適用於訊號調理與放大器電路。
無詳細腳位定義資料: TAS5100DAP.
請參閱 資料表 以查看完整腳位配置。
典型應用
TAS5100DAP 適用於 6 應用s: Home-Theater Powered Speakers, Digital Multimedia Speaker, Home-Audio Receiver Output, Industrial Audio Announcement System, Digital Active Speaker Crossover, Digital Audio Reference Monitor.
Home-Theater Powered Speakers
TAS5100DAP fits a powered speaker driven by a digital audio codec or DSP because it accepts digital audio directly and supplies up to 30 W RMS into a 6-ohm load. Its 0.08% THD+N at 1 kHz supports low-distortion reproduction of dialogue and music, while efficiency above 90% into an 8-ohm load limits waste in compact enclosures. The design must provide adequate PowerPAD copper and via area, preserve the exposed-pad ground connection, and verify continuous output against the selected supply voltage and speaker impedance.
Digital Multimedia Speaker
A desktop or multimedia speaker can use TAS5100DAP as the Class-D output stage behind a digital audio interface, eliminating a separate analog power-amplifier path. The device's 30 W RMS capability is appropriate for compact powered speakers, and its greater-than-90-percent efficiency into 8 ohms improves power use compared with a linear output stage. Designers should keep digital audio routing away from the output and PowerPAD region, use a clean low-noise supply, and test the enclosure at sustained playback levels before fixing the output-power target.
Home-Audio Receiver Output
TAS5100DAP can serve as a mono output stage in a home-audio receiver or digital amplifier when upstream circuitry supplies a compatible digital audio stream. The 30 W RMS specification, 93 dB TDAA-system dynamic range, and 0.08% THD+N at 1 kHz into 6 ohms provide useful performance targets for music reproduction. The implementation should confirm signal format, clocking, latency behavior, and mute controls against the manufacturer interface description while sizing the thermal plane for sustained output.
Industrial Audio Announcement System
For industrial announcement and notification equipment, TAS5100DAP can amplify a digital audio stream into a speaker without adding an analog output amplifier. Its Class-D topology offers greater than 90-percent efficiency into an 8-ohm load, which is valuable when sustained speech playback creates a substantial thermal load. The amplifier still requires protection appropriate to the installation, including assessment of speaker impedance, cable length, power-supply tolerance, and fault conditions that could create excessive output current or thermal stress.
Digital Active Speaker Crossover
TAS5100DAP can power the woofer section of a digital active crossover when the DSP supplies the correct channel data and the driver operates within the intended impedance. A 30 W RMS stage and 0.08% THD+N at 1 kHz into 6 ohms can support controlled low-frequency reproduction, but crossover settings must prevent sustained near-limit operation that overheats the output stage. Use the manufacturer filter and modulation guidance, maintain clean grounds, and validate the complete loudspeaker network acoustically.
Digital Audio Reference Monitor
A near-field digital monitor can use TAS5100DAP where a compact 30 W RMS Class-D stage is useful. The specified 0.08% THD+N at 1 kHz into 6 ohms and 93 dB dynamic range in the TDAA system provide concrete baseline metrics, although perceived monitor performance also depends on the DAC, signal chain, crossover, enclosure, and room correction. Keep switching-node and return-current paths controlled, provide low-impedance supply distribution, and verify that the chosen speaker load does not create thermal or current excursions.
工程參考資料,適用於 TAS5100DAP — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 |
|---|---|
| Product Type | Digital audio power output stage |
| Brand | Texas Instruments |
| Package | 32-pin HTSSOP with PowerPAD |
| Channel Configuration | 1 channel mono |
| Maximum Output Power | 30 W RMS |
| Dynamic Range | 93 dB in TDAA system |
| Total Harmonic Distortion plus Noise | 0.08% at 1 kHz and 30 W RMS into 6 ohm |
| Power Efficiency | >90% into 8 ohm load |
設計說明
Estimated: power dissipation equals output power divided by efficiency. At 30 W output and 90% efficiency, the ideal conduction loss is approximately 3.3 W before accounting for additional internal losses. Use the PCB copper area, exposed-PowerPAD connection, and thermal via pattern from the manufacturer layout guidance. Verify that estimated junction temperature remains below the device rating at the highest ambient temperature and intended continuous-output duty cycle.
Connect the exposed PowerPAD to the PCB ground and thermal plane with multiple thermal vias, and keep the exposed-pad footprint free of accidental thermal isolation. Route high-current output and supply paths with copper areas appropriate for 30 W-class output. Place the PowerPAD connection directly beneath the package where the land pattern permits and avoid placing temperature-sensitive or mechanically sensitive components in the hottest region of the board.
Do not equate the 30 W RMS headline rating with guaranteed continuous output at every supply voltage or speaker impedance. Check the manufacturer operating limits, supply headroom, load restrictions, protection behavior, and thermal conditions. A speaker with impedance below the supported load can increase current and heat, while a supply that cannot support the required peak voltage can cause clipping or reduce usable output even though the nominal rating is 30 W RMS.
合規資訊
The commercial-temperature product is not an automotive-grade variant. RoHS, REACH, lead-free, halogen-free, and conflict-minerals declarations should be confirmed against the current manufacturer product documentation before environmental or supply-chain qualification.