Texas Instruments

TAS5100DAP - 30W Mono Class-D Audio | Texas Instruments

料号: TAS5100DAP ✓ 量产中
32-pin HTSSOP with PowerPAD Package
最小起订量: 1 |

TAS5100DAP 概述

The Texas Instruments TAS5100DAP is a mono Class-D digital audio power output stage rated for 30 W RMS power, with a 93 dB dynamic range in the TDAA system and THD+N of 0.08% at 1 kHz into a 6-ohm load. The device is packaged in a low-profile 32-pin HTSSOP with an exposed PowerPAD thermal pad.

A Class-D power stage is a switching audio amplifier topology that controls current through the speaker output according to a pulse-width-modulated signal. Compared with a linear audio amplifier, this approach can achieve power efficiency above 90% into an 8-ohm load, reducing the amount of heat that must be removed from the audio output stage. The TAS5100DAP is a power-output-stage device intended for use with a preceding audio codec, DAC, DSP, or digital audio interface.

Key performance features include 30 W RMS output capability, 0.08% THD+N at 1 kHz into 6 ohms, 93 dB dynamic range in the TDAA system, and greater than 90% power efficiency into an 8-ohm load. Its digital input architecture supports direct reception of digital audio signals, avoiding an analog input stage and associated conversion circuitry in systems where a digital audio source is already available.

The 32-pin HTSSOP package provides a compact surface-mount solution with a PowerPAD for heat dissipation. The commercial temperature range extends from 0°C to 70°C. Because a 30 W output stage can dissipate substantial heat at low supply voltages or into low-impedance speakers, PCB copper area, thermal via layout, and the selected speaker load must be evaluated during system design.

Typical applications include home-theater and multimedia speaker amplification, powered speaker designs, digital audio receiver output stages, compact consumer audio products, and industrial audio systems using a digital signal-processing front end. The device is particularly suitable when low idle dissipation, high conversion efficiency, and direct digital audio control are priorities.

The main design tradeoff is power dissipation at low supply headroom. Output power is constrained by both supply voltage, speaker impedance, and thermal conditions; a nominal 30 W capability does not guarantee 30 W continuously at every input voltage or ambient temperature. Use the manufacturer powerPAD layout guidance and thermal calculations to establish dependable operating limits.

This product page consolidates the principal electrical characteristics, verified package information, application guidance, thermal considerations, and comparison criteria for the TAS5100DAP. It also distinguishes verified drop-in replacements from merely similar devices so engineers can make a footprint-compatible sourcing decision without changing the PCB.

直接替换替代料: TAS5100DAP ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。

TAS5100DCA

✅ 直接替换 ⚠️ 规格未核验
📦 32-terminal HTSSOP with PowerPAD
Same TAS5100A family and 30 W output class; package-code and thermal details must be verified because the exact terminal and pad differences are not quantified in the available cross-reference records.

📋 参考替代料(不在目录中)

TAS5100DAP 最大额定值与电气特性

Product Type Digital audio power output stage
Amplifier Type Class-D
Channel Configuration 1 channel mono
Maximum Output Power 30 W RMS
Dynamic Range 93 dB in TDAA system
Total Harmonic Distortion plus Noise 0.08% at 1 kHz and 30 W RMS into 6 ohm
Power Efficiency >90% into 8 ohm load
封装 32-pin HTSSOP with PowerPAD
Number of Terminals 32 terminals
Package Shape Rectangular gull-wing
安装类型 Surface mount
Temperature Grade Commercial
工作温度范围 0°C to 70°C
Output Load 6 ohm and 8 ohm loads
Audio Input Digital audio input

TAS5100DAP rectangular gull-wing 引脚配置指南

TAS5100DAP(rectangular gull-wing 封装)的引脚配置。 该模拟元件具有输入、输出和电源引脚。请参阅制造商数据手册以了解失调调零、补偿和使能引脚配置。适用于信号调理和放大器电路。

TAS5100DAP 的 rectangular gull-wing 封装引脚图

暂无详细引脚数据: TAS5100DAP.

请参阅 数据手册 以查看完整引脚配置。

典型应用

TAS5100DAP 适用于 6 应用s: Home-Theater Powered Speakers, Digital Multimedia Speaker, Home-Audio Receiver Output, Industrial Audio Announcement System, Digital Active Speaker Crossover, Digital Audio Reference Monitor.

🎧

Home-Theater Powered Speakers

TAS5100DAP fits a powered speaker driven by a digital audio codec or DSP because it accepts digital audio directly and supplies up to 30 W RMS into a 6-ohm load. Its 0.08% THD+N at 1 kHz supports low-distortion reproduction of dialogue and music, while efficiency above 90% into an 8-ohm load limits waste in compact enclosures. The design must provide adequate PowerPAD copper and via area, preserve the exposed-pad ground connection, and verify continuous output against the selected supply voltage and speaker impedance.

🔊

Digital Multimedia Speaker

A desktop or multimedia speaker can use TAS5100DAP as the Class-D output stage behind a digital audio interface, eliminating a separate analog power-amplifier path. The device's 30 W RMS capability is appropriate for compact powered speakers, and its greater-than-90-percent efficiency into 8 ohms improves power use compared with a linear output stage. Designers should keep digital audio routing away from the output and PowerPAD region, use a clean low-noise supply, and test the enclosure at sustained playback levels before fixing the output-power target.

📺

Home-Audio Receiver Output

TAS5100DAP can serve as a mono output stage in a home-audio receiver or digital amplifier when upstream circuitry supplies a compatible digital audio stream. The 30 W RMS specification, 93 dB TDAA-system dynamic range, and 0.08% THD+N at 1 kHz into 6 ohms provide useful performance targets for music reproduction. The implementation should confirm signal format, clocking, latency behavior, and mute controls against the manufacturer interface description while sizing the thermal plane for sustained output.

🏭

Industrial Audio Announcement System

For industrial announcement and notification equipment, TAS5100DAP can amplify a digital audio stream into a speaker without adding an analog output amplifier. Its Class-D topology offers greater than 90-percent efficiency into an 8-ohm load, which is valuable when sustained speech playback creates a substantial thermal load. The amplifier still requires protection appropriate to the installation, including assessment of speaker impedance, cable length, power-supply tolerance, and fault conditions that could create excessive output current or thermal stress.

🔊

Digital Active Speaker Crossover

TAS5100DAP can power the woofer section of a digital active crossover when the DSP supplies the correct channel data and the driver operates within the intended impedance. A 30 W RMS stage and 0.08% THD+N at 1 kHz into 6 ohms can support controlled low-frequency reproduction, but crossover settings must prevent sustained near-limit operation that overheats the output stage. Use the manufacturer filter and modulation guidance, maintain clean grounds, and validate the complete loudspeaker network acoustically.

🖥️

Digital Audio Reference Monitor

A near-field digital monitor can use TAS5100DAP where a compact 30 W RMS Class-D stage is useful. The specified 0.08% THD+N at 1 kHz into 6 ohms and 93 dB dynamic range in the TDAA system provide concrete baseline metrics, although perceived monitor performance also depends on the DAC, signal chain, crossover, enclosure, and room correction. Keep switching-node and return-current paths controlled, provide low-impedance supply distribution, and verify that the chosen speaker load does not create thermal or current excursions.

What is the Texas Instruments TAS5100DAP?
The Texas Instruments TAS5100DAP is a mono Class-D digital audio power output stage designed for 30 W RMS output and supplied in a 32-pin HTSSOP package. According to the Texas Instruments datasheet, it provides 93 dB dynamic range in the TDAA system, 0.08% THD+N at 1 kHz into 6 ohms, and power efficiency above 90% into an 8-ohm load. It accepts digital audio information and is intended to operate with an upstream codec, DAC, DSP, or audio interface.
What are the key specifications of TAS5100DAP that engineers should know?
The TAS5100DAP combines a 30 W RMS Class-D output rating with digital audio input and a 32-pin HTSSOP package. The Texas Instruments datasheet lists 0.08% THD+N at 1 kHz when delivering 30 W RMS into 6 ohms, greater than 90% efficiency into an 8-ohm load, and 93 dB dynamic range in the TDAA system. Its commercial operating range is 0°C to 70°C, and the exposed PowerPAD must be connected to the PCB thermal plane.
Where can I download the TAS5100DAP datasheet PDF?
The TAS5100DAP datasheet PDF can be accessed through the datasheet archive link listed on this page or through Texas Instruments' product-search resources. The archived document is 16 pages and describes the true digital audio amplifier TAS5100A PWM power output stage, including its applications, electrical characteristics, and package information. Use the manufacturer's pin-description and PowerPAD layout sections when assigning PCB connections or planning thermal-via placement.
Where can I find the TAS5100DAP pinout?
The TAS5100DAP pinout is presented in the 16-page Texas Instruments datasheet linked from this page. The component uses a 32-terminal HTSSOP package and includes a PowerPAD thermal connection. Because a complete terminal-name table is not published in the product-indexed material used for this page, assign signals by using the numbered pin-description table and land-pattern drawing in the manufacturer datasheet rather than inferring connections from the distributor package summary.
How much power can TAS5100DAP deliver to a speaker?
TAS5100DAP is specified for 30 W RMS output, with the headline performance figure measured at 1 kHz into a 6-ohm load. Actual continuous output depends on the power-supply voltage, load impedance, signal level, thermal design, and ambient temperature. The speaker must also tolerate the available output. Use conservative thermal analysis when operating near the 30 W limit because lower supply headroom or a lower-impedance load can increase internal dissipation.
Is TAS5100DAP suitable for a digital powered speaker?
Yes, TAS5100DAP is suitable for a digital powered speaker because it is a digital Class-D power output stage rather than an analog audio amplifier. The upstream codec, DAC, or DSP can provide the digital audio stream directly, avoiding an unnecessary analog-to-digital conversion path. The device provides 30 W RMS capability and greater than 90% efficiency into an 8-ohm load, making it useful for compact home-theater, multimedia, and consumer powered-speaker designs.
What is the difference between TAS5100DAP and TAS5110DAD?
TAS5100DAP and TAS5110DAD are both Texas Instruments digital audio amplifier products, but the indexed comparison identifies them as different device variants rather than confirmed pin-to-pin equivalents. TAS5100DAP is a 30 W mono Class-D stage in a 32-pin HTSSOP, while the full electrical and package differences for TAS5110DAD must be checked before interchangeability is claimed. Use the manufacturer datasheets and PCB footprint comparison rather than treating the shared family name as proof of drop-in compatibility.
When should I choose TAS5100DAP over another digital audio power stage?
Choose TAS5100DAP when the design requires a 30 W RMS mono Class-D stage, a digital audio interface, and a 32-pin HTSSOP PowerPAD implementation. It is a strong fit when efficiency above 90% into 8 ohms and THD+N of 0.08% at 1 kHz into 6 ohms are important. Select a different amplifier if the required load, supply voltage, channel count, thermal envelope, input format, or automotive qualification differs from those design targets.
Is TAS5100DAP suitable for home theater audio amplification?
TAS5100DAP is suitable for a home-theater or multimedia power-output stage that consumes digital audio from a codec or DSP. Its 30 W RMS rating can suit powered speakers, compact soundbars, and compact home-audio enclosures, while greater than 90% efficiency into an 8-ohm load reduces output-stage heat. The enclosure still requires adequate ventilation, and the PowerPAD thermal design must be tied to the PCB copper area for reliable operation near rated power.
What can replace TAS5100DAP?
No verified drop-in replacement for TAS5100DAP is established by the available manufacturer and cross-reference information. A valid replacement must use the same 32-pin HTSSOP land pattern, maintain pin-to-pin signal compatibility, support the same digital-audio format and clocking, and provide adequate output current, heat spreading, and power handling. Similar power ratings alone are insufficient because the input interface, control pins, exposed-pad connection, and protection behavior must also match.
What is the best drop-in replacement for TAS5100DAP?
The best drop-in replacement is the part that matches the TAS5100DAP pinout, package, digital input interface, supply limits, output configuration, and 30 W-class thermal capability. No candidate in the verified cross-reference results meets all of those conditions, so none can be responsibly labeled drop-in. For an existing PCB, retain TAS5100DAP or obtain a manufacturer-confirmed equivalent; for a new design, compare the complete datasheets and application circuits before changing the footprint.
Where to buy TAS5100DAP online?
Use the Request a Quote form on this page to request TAS5100DAP availability, current lead time, and order handling from XAIPART. The form is the appropriate purchasing route because stock and commercial terms can change independently of technical documentation. Provide the exact TAS5100DAP MPN, required quantity, and delivery location so the request can be matched to the correct 32-pin HTSSOP device without confusing it with related amplifier families.
What is the price of TAS5100DAP?
Submit a TAS5100DAP request through the Request a Quote form on this page for current commercial pricing. The listed distributor summaries include a Marketplace entry, but they do not expose a qualifying quantity-break price table for the exact MPN in the material available for this page. The quote form allows the requested quantity and delivery terms to be evaluated against current availability without presenting stale commercial information.
What is the lead time for TAS5100DAP?
The current lead time for TAS5100DAP should be requested through the Request a Quote form on this page. Lead time can vary with order quantity, procurement conditions, and the manufacturer's available supply, so a historical distributor indication should not be treated as a current manufacturing commitment. Include the required quantity and target delivery date in the request to obtain an actionable scheduling response for the exact 32-pin HTSSOP MPN.
Is TAS5100DAP in stock?
Current TAS5100DAP stock should be confirmed through the Request a Quote form on this page. The product index identifies the MPN as a 30 W mono Class-D amplifier in a 32-pin HTSSOP, but live inventory can change quickly and differs by contract and shipment destination. Submit the exact quantity and required date so XAIPART can check current availability and provide an order response for the part.
How should the TAS5100DAP PowerPAD be connected?
Connect the TAS5100DAP exposed PowerPAD to the PCB ground and thermal plane according to the manufacturer land-pattern and thermal guidance, then use multiple thermal vias to transfer heat into the board. Keep the exposed-pad connection and via pattern compatible with the 32-pin HTSSOP footprint. The power stage can dissipate substantial heat near its output limit, so copper area, via count, enclosure ventilation, and ambient temperature must be considered together.

工程参考数据: TAS5100DAP ——对比、设计指导和合规信息。

选型指南

TAS5100DAP is appropriate when a system already has digital audio and needs a compact mono Class-D output stage with up to 30 W RMS capability. Its direct digital input can simplify the signal path, while 0.08% THD+N at 1 kHz into 6 ohms and greater than 90-percent efficiency into 8 ohms make it useful for powered speakers and multimedia audio equipment. Choose it over an analog power amplifier when avoiding a digital-to-analog conversion stage is a priority. No verified drop-in alternatives are available, so do not substitute a merely similar amplifier without checking the complete pinout, digital interface, clocking, supplies, protection, and PowerPAD layout. For new designs, compare the required output level, speaker impedance, thermal environment, and enclosure constraints against the manufacturer operating limits before committing the 32-pin HTSSOP footprint.

与替代料对比

参数 本产品
Product Type Digital audio power output stage
Brand Texas Instruments
Package 32-pin HTSSOP with PowerPAD
Channel Configuration 1 channel mono
Maximum Output Power 30 W RMS
Dynamic Range 93 dB in TDAA system
Total Harmonic Distortion plus Noise 0.08% at 1 kHz and 30 W RMS into 6 ohm
Power Efficiency >90% into 8 ohm load

设计说明

Estimated: power dissipation equals output power divided by efficiency. At 30 W output and 90% efficiency, the ideal conduction loss is approximately 3.3 W before accounting for additional internal losses. Use the PCB copper area, exposed-PowerPAD connection, and thermal via pattern from the manufacturer layout guidance. Verify that estimated junction temperature remains below the device rating at the highest ambient temperature and intended continuous-output duty cycle.

Connect the exposed PowerPAD to the PCB ground and thermal plane with multiple thermal vias, and keep the exposed-pad footprint free of accidental thermal isolation. Route high-current output and supply paths with copper areas appropriate for 30 W-class output. Place the PowerPAD connection directly beneath the package where the land pattern permits and avoid placing temperature-sensitive or mechanically sensitive components in the hottest region of the board.

Do not equate the 30 W RMS headline rating with guaranteed continuous output at every supply voltage or speaker impedance. Check the manufacturer operating limits, supply headroom, load restrictions, protection behavior, and thermal conditions. A speaker with impedance below the supported load can increase current and heat, while a supply that cannot support the required peak voltage can cause clipping or reduce usable output even though the nominal rating is 30 W RMS.

合规信息

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
无铅
Unknown
无卤
Unknown
冲突矿物
Unknown

The commercial-temperature product is not an automotive-grade variant. RoHS, REACH, lead-free, halogen-free, and conflict-minerals declarations should be confirmed against the current manufacturer product documentation before environmental or supply-chain qualification.

数据核验日期: 2026-11-10 ——数据由 XAIPART 元器件工程团队核验和整理

相关搜索

TAS5100DAP datasheet TAS5100DAP datasheet pdf TAS5100DAP pinout TAS5100DAP specifications TAS5100DAP 30W Class-D TAS5100DAP 32 HTSSOP TAS5100DAP equivalent TAS5100DAP replacement TAS5100DAP vs TAS5110DAD TAS5100DAP application circuit TAS5100DAP price TAS5100DAP stock Texas Instruments TAS5100DAP

相关元器件 & 术语

Texas Instruments TAS5100DAP TAS5100A TAS5110DAD Class-D amplifier digital audio power output stage PWM TDAA THD+N dynamic range power efficiency mono amplifier 32-pin HTSSOP PowerPAD surface-mount package digital audio input 6 ohm speaker 8 ohm speaker powered speaker home theater audio RoHS REACH AEC-Q100 Texas Instruments cross-reference search
快速报价
填写完整信息——我们的销售团队将在 24 小时内回复
料号 制造商 封装 QTY 目标价 小计
✓
报价已提交!

我们将在 24 小时内回复您的邮件

1
询价已提交
2
已收到报价
3
已下单
4
支付
5
已发货
6
已送达
查看询价详情