最後購買通知: THS3091DDA 即將停產。最後下單日期: 聯絡我們. 查看可用的替代零件 →
Texas Instruments

THS3091DDA - ±16V 180MHz Current-Feedback Op Amp | Texas Instruments

MPN: THS3091DDA ✗ 停產
32 V Vdss 310 mA Id 8-pin SOIC PowerPAD Package
MOQ: 1 |

THS3091DDA 概覽

Texas Instruments THS3091DDA is a single, high-voltage, low-distortion current-feedback operational amplifier with a 180 MHz bandwidth, a wide 32 V total supply range, a 6000 V/μs slew rate, and up to 310 mA output current. The device is offered in an 8-pin SOIC PowerPAD package for high-voltage arbitrary-waveform-driver, pin-driver, power-FET-driver, and VDSL line-driver applications.

A current-feedback operational amplifier is a voltage-feedback amplifier alternative optimized for high-speed, wide-gain-bandwidth operation. Unlike a conventional voltage-feedback amplifier, its closed-loop bandwidth and stability characteristics vary with gain. In the system hierarchy, the THS3091DDA is a current-feedback amplifier within the broader operational-amplifier, analog-amplifier, and integrated-circuit categories. This topology is particularly useful when driving low-resistance and high-capacitance loads while retaining high output-current capability.

The THS3091DDA combines a wide operating supply range of ±5 V to ±16 V with low-distortion signal handling. Its 6000 V/μs slew rate supports rapid transitions, while the 310 mA output-current capability provides useful drive for test equipment, waveform generators, and communication-line interfaces. The single-amplifier configuration also simplifies designs that require one high-speed output channel rather than a dual or quad amplifier.

The THS309x family uses a current-feedback architecture to achieve strong bandwidth performance and good drive capability. Texas Instruments identifies the devices as suitable for applications requiring large, linear output signals, including pin drivers, power-FET drivers, and arbitrary-waveform generators. The ability to handle large voltage swings into demanding loads while maintaining settling performance makes the amplifier useful in laboratory instrumentation and communication test systems.

Typical uses include ultrasonic test and measurement, high-voltage pin and FET test fixtures, arbitrary waveform generation, and VDSL line-driver interfaces. In each case, the amplifier converts a low-level control waveform into a larger-amplitude output while the current-feedback architecture preserves useful high-speed behavior. Designers should still verify load capacitance, output-current duration, supply headroom, and thermal rise for the complete operating condition.

For layout, follow the manufacturer pin and thermal-pad guidance and place input, feedback, and decoupling connections to minimize parasitic feedback. The integrated PowerPAD requires a low-impedance copper connection to the ground plane for electrical and thermal performance. Use short, direct feedback routing and provide local supply bypassing close to the device rather than relying on distant bulk capacitance.

This product page combines the Texas Instruments product information with a practical focus on supply range, bandwidth, slew rate, output drive, package construction, lifecycle status, and design trade-offs. It also organizes same-footprint alternatives so engineers can evaluate replacement candidates against the original THS3091DDA before approving a PCB or production change.

直接替換替代品,適用於 THS3091DDA — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。

THS3092DDAR

✅ 直接替換
📦 8-SO PowerPAD
Channel-specific electrical ratings differ by

📋 參考替代品(不在目錄中)

THS3062DDAG3

✅ 直接替換
📦 8-SO PowerPAD
Different THS30xx channel characteristics with

📋 參考替代品(不在目錄中)

THS3091DDA 最大額定值與電氣特性

Amplifier Type Single current-feedback operational amplifier
Number of Circuits 1 circuit
Gain-Bandwidth Product 180 MHz
Total Supply Range 32 V
Nominal Operating Supply Range ±5 V to ±16 V
Slew Rate 6000 V/μs
Output Current 310 mA
Amplifier Architecture Current feedback
Signal Type Single-ended
封裝 8-pin SOIC PowerPAD
安裝類型 Surface mount
生命週期狀態 No longer in production

THS3091DDA 8-pin soic powerpad 腳位配置指南

THS3091DDA(8-pin soic powerpad 封裝)的腳位配置。 此類比元件具有輸入、輸出與電源腳位。偏移歸零、補償與致能腳位配置請參閱製造商資料表。適用於訊號調理與放大器電路。

THS3091DDA 的 8-pin soic powerpad 封裝腳位圖

無詳細腳位定義資料: THS3091DDA.

請參閱 資料表 以查看完整腳位配置。

典型應用

THS3091DDA 適用於 6 應用s: Semiconductor Pin Test Drivers, Power-FET Gate Drivers, Arbitrary Waveform Generators, VDSL Line-Driver Interfaces, Ultrasonic Test Instrumentation, Low-Resistance Load Test Equipment.

🧪

Semiconductor Pin Test Drivers

The THS3091DDA fits semiconductor pin-test systems that must generate large, rapidly changing voltage waveforms at a device terminal. Its 6000 V/μs slew rate supports fast edge transitions, while its output current capability of up to 310 mA gives the driver authority for resistive and capacitive fixture loads. The single-amplifier arrangement simplifies one-channel drive stages and reduces board area. Place the feedback components close to the amplifier and validate settling with the actual cable, socket, and probe capacitance because capacitive loading can affect current-feedback stability. The 8-pin SOIC PowerPAD also provides a practical surface-mount construction for multi-channel test equipment.

⚡

Power-FET Gate Drivers

The THS3091DDA is appropriate for power-FET gate-driver circuits requiring a large voltage swing and strong transient current. Its ±5 V to ±16 V supply range supports bipolar drive conditions, and its 6000 V/μs slew rate produces fast gate transitions. The up-to-310-mA output capability helps drive the gate capacitance and minimizes edge distortion. Because FET gate loading is highly dependent on device size and operating frequency, verify peak and continuous current against the selected transistor and the manufacturer datasheet. Keep feedback traces short and provide a low-impedance ground connection beneath the PowerPAD to preserve high-frequency behavior.

📊

Arbitrary Waveform Generators

The THS3091DDA supports the output stage of an arbitrary waveform generator that must produce large linear signals into practical test loads. Its 180 MHz bandwidth and 6000 V/μs slew rate provide a strong combination of signal frequency and transition-rate capability, while the wide supply range increases available output amplitude. The 310 mA drive capability is useful when the generator feeds low-impedance or appreciably capacitive loads. Engineer the feedback network for the target gain because current-feedback amplifiers have gain-dependent bandwidth and stability. Confirm output settling, offset, distortion, and thermal rise with the complete output network rather than a nominal 50-ohm test load alone.

🌐

VDSL Line-Driver Interfaces

The THS3091DDA is suitable for VDSL-related line-driver interfaces where large, low-distortion voltage swings are needed. Texas Instruments identifies VDSL line drivers among the intended THS309x applications. The ±5 V to ±16 V supply range, 180 MHz bandwidth, 6000 V/μs slew rate, and output-current capability provide a useful foundation for short-reach or termination networks. Line-driver performance also depends on transformer or balun characteristics, output impedance, isolation requirements, and allowable distortion. Characterize the complete channel because a fast amplifier alone does not guarantee acceptable mask or return-loss performance.

🔧

Ultrasonic Test Instrumentation

The THS3091DDA can serve as a high-voltage output amplifier in ultrasonic test and measurement equipment. Its 6000 V/μs slew rate supports low-distortion reproduction of high-frequency bursts, while the broad supply range permits larger transducer excitation voltages than conventional low-voltage operational amplifiers. The output-current capability helps drive transducer and cable capacitance, although the actual limit must be checked for each frequency and load combination. Use short feedback routing, local decoupling, and a carefully controlled ground return to minimize high-frequency coupling. Confirm transducer breakdown voltage, allowable duty cycle, and amplifier thermal dissipation before increasing drive amplitude.

🏭

Low-Resistance Load Test Equipment

The THS3091DDA fits measurement equipment that drives low-resistance loads while maintaining large output swings. Its high slew rate limits the transition time needed to reach a commanded voltage, and its current capability provides more drive than a conventional small-signal operational amplifier. These properties make it useful in automated load fixtures and high-speed current or power-device characterization systems. The thermal design must account for sustained voltage and current because dissipation rises with output swing and load. Start with conservative load values, monitor output settling and waveform distortion, and use the manufacturer current-limit and power information to establish safe operating boundaries.

推薦產品摘要

THS3092DDAR Same-package high-voltage amplifier comparison candidate 用於: Semiconductor Pin Test Drivers, Power-FET Gate Drivers, Arbitrary Waveform Generators, VDSL Line-Driver Interfaces, Ultrasonic Test Instrumentation, Low-Resistance Load Test Equipment THS3062DDAG3 Same-package THS30xx amplifier comparison candidate 用於: Semiconductor Pin Test Drivers, Power-FET Gate Drivers, Arbitrary Waveform Generators, VDSL Line-Driver Interfaces, Ultrasonic Test Instrumentation, Low-Resistance Load Test Equipment
What is the THS3091DDA?
The THS3091DDA is a single high-voltage, low-distortion current-feedback operational amplifier designed for large-signal, high-speed output stages. According to the Texas Instruments THS3091 product page, it has a 180 MHz bandwidth, operates across a 32 V total supply range, and is packaged in an 8-pin SOIC PowerPAD. Its intended uses include pin drivers, power-FET drivers, VDSL line drivers, and arbitrary-waveform generators.
What is the supply voltage range of the THS3091DDA?
The THS3091DDA is specified for dual supplies from ±5 V to ±16 V, corresponding to a total supply span of 32 V. According to the Texas Instruments THS3091 product page, this wide range supports high-output-swing applications such as waveform generation and line-driver circuits. The amplifier should be operated within the absolute maximum ratings in the manufacturer datasheet, with suitable supply decoupling and adequate output-voltage headroom for the selected load.
What are the key specifications of THS3091DDA that engineers should know?
The principal THS3091DDA specifications are 180 MHz bandwidth, a 6000 V/μs slew rate, up to 310 mA output current, and operation from ±5 V to ±16 V. Texas Instruments describes the device as a high-voltage, low-distortion current-feedback amplifier for demanding load-driving applications. These figures make it most relevant to high-speed waveform generation, pin and FET testing, and communication equipment where rapid large-signal transitions are required.
Where can I download the THS3091DDA datasheet PDF?
The official THS3091DDA documentation is available through the Texas Instruments THS3091 product page at https://www.ti.com/product/THS3091. That page links the THS309x manufacturer datasheet and provides ordering, quality, lifecycle, and application information. The manufacturer identifies THS3091DDA as no longer in production, so engineers should also use the device documentation to plan a last-time-buy, redesign, or qualified replacement strategy.
Where can I find the THS3091DDA pinout?
The THS3091DDA pinout is shown in the pin-configuration section of the Texas Instruments THS309x manufacturer datasheet. The device uses an 8-pin SOIC PowerPAD package, so the exposed thermal pad is part of the thermal and electrical construction and must be connected according to the manufacturer layout guidance. Use the pin-description table and package drawing to assign supply, input, output, feedback, and thermal-pad connections on the PCB.
Why is the THS3091DDA suitable for a pin driver?
The THS3091DDA suits pin-driver service because it combines a 6000 V/μs slew rate with up to 310 mA output current and operation from ±5 V to ±16 V. These characteristics allow a small control signal to produce a larger, rapidly changing voltage at a device pin. According to Texas Instruments, its ability to handle large voltage swings into low-resistance and high-capacitance loads is particularly valuable in pin-driver and power-FET-driver applications.
Can the THS3091DDA drive a high-capacitance load?
The THS3091DDA can drive high-capacitance loads, although the allowable capacitance and resulting stability depend on gain, output amplitude, frequency, and the external feedback network. Texas Instruments identifies large-signal drive into high-capacitance loads as an intended strength of the THS309x family. Prototype the feedback layout, isolate capacitive loads when necessary, and verify settling at the required bandwidth with an oscilloscope and representative load.
THS3091DDA vs THS3092DDAR - which is better for a power-FET driver?
The THS3091DDA is the better choice when its specified output-drive and distortion characteristics match the power-FET gate requirements, while THS3092DDAR should be selected when its channel-specific electrical limits better fit the design. Both are identified in same-package comparison resources, but the available comparison does not provide a complete quantified parameter matrix. Review both manufacturer datasheets for slew rate, output-current, gain-bandwidth, distortion, and compensation requirements before substitution.
When should I choose THS3091DDA over THS3092DDAR?
Choose THS3091DDA when the original design has already been qualified around its 180 MHz bandwidth, 6000 V/μs slew rate, and 310 mA output-current capability. Choose THS3092DDAR when its channel-specific specifications provide a better match for the intended waveform, load, or gain condition. Because current-feedback amplifiers do not have conventional voltage-feedback gain bandwidth, perform a gain-dependent stability and settling comparison rather than relying only on the headline bandwidth number.
Is THS3091DDA suitable for an arbitrary waveform generator?
Yes, the THS3091DDA is suitable for arbitrary waveform generators requiring large, linear output swings and high slew rate. Texas Instruments specifically identifies arbitrary-waveform-driver applications as a use case for the THS309x family. Its 32 V total supply range, 6000 V/μs slew rate, and up to 310 mA output current support high-amplitude signals, provided the load, bandwidth, thermal conditions, and feedback compensation remain within the manufacturer specifications.
What is the best drop-in replacement for THS3091DDA?
The best drop-in replacement is the candidate that preserves the 8-pin SOIC PowerPAD footprint, pin assignments, supply range, output-drive capability, and gain-dependent stability. THS3092DDAR and THS3062DDAG3 are documented same-package comparison candidates, but no universal drop-in rating should be assigned without checking every operating parameter. Because THS3091DDA is no longer in production, request the current quotation and use a manufacturer-supported cross-reference for the production revision.
What can replace THS3091DDA?
THS3092DDAR and THS3062DDAG3 are documented alternatives that warrant pin, package, and electrical comparison with the THS3091DDA. A valid replacement must also preserve the ±5 V to ±16 V operating class where required, provide suitable slew rate and output current, and maintain stability at the selected gain. Treat these as qualified candidates rather than unconditional replacements, and validate waveform distortion, load drive, temperature, and PCB thermal performance.
Is THS3091DDA the same as THS3091DDAR?
THS3091DDA and THS3091DDAR identify the same THS3091 device family and 8-pin SOIC PowerPAD construction, with the ordering suffix distinguishing the orderable packaging form. They are not distinct amplifier designs. When moving between suffix variants, confirm reel or tape orientation, quantity, exposed-pad construction, and the ordering details shown on the Texas Instruments part-details page. A packaging change does not alter the core amplifier function.
What is the best cross-brand equivalent for THS3091DDA?
No cross-brand equivalent is established here because the available cross-reference material does not demonstrate both an identical 8-pin SOIC PowerPAD footprint and quantified electrical compatibility with the THS3091DDA. A valid cross-brand substitute must match pin assignments, ±5 V to ±16 V supply requirements, current-feedback behavior, output-drive capability, gain-dependent stability, and thermal performance. AD8361ARMZ-REEL appears as a suggested alternative in an aggregator listing, but its package and electrical requirements must be independently confirmed before considering it.
Where to buy THS3091DDA online?
Use the Request a Quote form on this page to request THS3091DDA availability, minimum order quantity, and delivery terms. Texas Instruments identifies THS3091DDA as no longer in production, so availability may depend on remaining inventory, lifecycle status, and approved sourcing conditions. Provide the required quantity, target date, and assembly packaging requirements with the request so procurement can confirm the appropriate supply path.
What is the price of THS3091DDA?
Request a current quotation for THS3091DDA through the Request a Quote form on this page. The part is identified by Texas Instruments as no longer in production, which can make quantity, traceability, and lifecycle terms more important than the original catalog price. Include the required order quantity and reel or tape packaging requirements with the request. Do not rely on an archived unit price for budgeting an active production build.
What is the lead time for THS3091DDA?
The current lead time for THS3091DDA must be confirmed through the Request a Quote form on this page because Texas Instruments marks the device as no longer in production. Lead time can vary with remaining inventory, order quantity, traceability requirements, and shipment destination. For an ongoing design, also request lifecycle-management guidance and consider a second-source qualification so production is not dependent on a single final-channel-of-sale opportunity.

工程參考資料,適用於 THS3091DDA — 比較、設計指引及合規資訊。

選型指南

Choose THS3091DDA when the design needs a single high-voltage current-feedback amplifier with a 32 V total supply range, 180 MHz bandwidth, 6000 V/μs slew rate, and up to 310 mA output current. It is especially appropriate for pin drivers, power-FET drivers, arbitrary waveform generators, and VDSL line-driver stages. Evaluate THS3092DDAR when its channel-specific bandwidth, distortion, output-drive, and compensation characteristics better fit the intended load. Consider THS3062DDAG3 only after verifying its gain-dependent stability, supply requirements, output-current ceiling, and waveform performance. Because the THS3091DDA is no longer in production, use it for compatible repair or inventory-based production while qualifying an alternate for new designs. No cross-brand option should be approved without verifying the footprint, pin assignment, supply range, stability, and thermal behavior.

與替代品比較

參數 本產品 THS3092DDAR THS3062DDAG3
Brand Texas Instruments Texas Instruments Texas Instruments
Package 8-pin SOIC PowerPAD 8-pin SOIC PowerPAD 8-pin SOIC PowerPAD

主要差異化特點

  • High output-drive capability for a single current-feedback amplifier (對比THS3092DDAR)
  • Large bipolar operating range for high-swing output stages (對比THS3062DDAG3)
  • 180 MHz bandwidth combined with current-feedback operation (對比THS3092DDAR)

設計說明

Connect the 8-pin SOIC PowerPAD thermal pad to a low-impedance ground plane using multiple vias and adequate copper area. The amplifier dissipates energy whenever its output voltage and load current are both nonzero, and low-resistance loads can produce substantial heating even though the package supports 310 mA output current. Check worst-case continuous dissipation and junction temperature against the manufacturer power limits. Keep thermal copper away from thermally sensitive analog sections where practical, and avoid concentrating heat around nearby precision components.

Use short, direct routing for the inverting input, feedback resistor, and output. Current-feedback amplifiers can become unstable when parasitic capacitance appears in the feedback node or input path. Place the feedback components adjacent to the amplifier pins, keep the non-inverting input route compact, and avoid long traces parallel to the output. Place supply-bypass capacitors close to the supply pins and follow the manufacturer datasheet grounding and decoupling layout for the PowerPAD construction.

Do not assume that the 180 MHz bandwidth is a fixed gain-bandwidth value like that of a voltage-feedback amplifier. The THS3091DDA is a current-feedback device, so bandwidth and stability vary with closed-loop gain and feedback impedance. Recheck stability and settling at every intended gain with the actual load capacitance, cable, probe, and output network. Also verify that peak output current, supply headroom, and package temperature remain within the manufacturer ratings.

The ±5 V to ±16 V supply capability allows large bipolar output swings, but the available output amplitude still depends on the selected supply, load, output-current direction, and voltage margin. Use separate local bypassing for each supply rail and avoid routing return current through the feedback reference. Check the output-stage dissipation for sustained DC output as well as sine-wave operation, because a centered large-amplitude waveform can consume more average power than an equivalent transient workload.

合規資訊

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
無鉛
Unknown
無鹵
Unknown
衝突礦產
Unknown

No specific RoHS, REACH, lead-free, halogen-free, or conflict-minerals declarations were identified in the manufacturer information represented for this product. The THS3091DDA is an industrial high-voltage operational amplifier rather than an automotive-qualified device.

相關搜尋

THS3091DDA THS3091DDA datasheet THS3091DDA datasheet pdf THS3091DDA pinout THS3091DDA specifications THS3091DDA equivalent THS3091DDA replacement THS3091DDA cross reference THS3091DDA vs THS3092DDAR THS3091DDA price THS3091DDA stock Texas Instruments THS3091DDA THS3091DDA application circuit THS3091DDA footprint

相關元件與詞彙

Texas Instruments THS3091DDA THS3091 THS3092DDAR THS3062DDAG3 current-feedback amplifier current-feedback operational amplifier operational amplifier analog amplifier integrated circuit semiconductor PowerPAD 8-pin SOIC surface mount SMD 180 MHz bandwidth 6000 V/μs slew rate 310 mA output current 32 V supply range pin driver power-FET driver arbitrary waveform generator VDSL line driver ultra-high-voltage
快速報價 RFQ
請填寫完整詳細資料 — 我們的業務團隊將於 24 小時內回覆
料號 製造商 封裝 QTY 目標價格 小計
✓
報價已提交!

我們將於 24 小時內回覆您的電子郵件

1
詢價已提交
2
已收到報價
3
已下單
4
付款
5
已出貨
6
已送達
檢視詢價單詳情