THS3091DDA - ±16V 180MHz Current-Feedback Op Amp | Texas Instruments
MPN: THS3091DDA ✗ סוף ייצורTHS3091DDA סקירה
A current-feedback operational amplifier is a voltage-feedback amplifier alternative optimized for high-speed, wide-gain-bandwidth operation. Unlike a conventional voltage-feedback amplifier, its closed-loop bandwidth and stability characteristics vary with gain. In the system hierarchy, the THS3091DDA is a current-feedback amplifier within the broader operational-amplifier, analog-amplifier, and integrated-circuit categories. This topology is particularly useful when driving low-resistance and high-capacitance loads while retaining high output-current capability.
The THS3091DDA combines a wide operating supply range of ±5 V to ±16 V with low-distortion signal handling. Its 6000 V/μs slew rate supports rapid transitions, while the 310 mA output-current capability provides useful drive for test equipment, waveform generators, and communication-line interfaces. The single-amplifier configuration also simplifies designs that require one high-speed output channel rather than a dual or quad amplifier.
The THS309x family uses a current-feedback architecture to achieve strong bandwidth performance and good drive capability. Texas Instruments identifies the devices as suitable for applications requiring large, linear output signals, including pin drivers, power-FET drivers, and arbitrary-waveform generators. The ability to handle large voltage swings into demanding loads while maintaining settling performance makes the amplifier useful in laboratory instrumentation and communication test systems.
Typical uses include ultrasonic test and measurement, high-voltage pin and FET test fixtures, arbitrary waveform generation, and VDSL line-driver interfaces. In each case, the amplifier converts a low-level control waveform into a larger-amplitude output while the current-feedback architecture preserves useful high-speed behavior. Designers should still verify load capacitance, output-current duration, supply headroom, and thermal rise for the complete operating condition.
For layout, follow the manufacturer pin and thermal-pad guidance and place input, feedback, and decoupling connections to minimize parasitic feedback. The integrated PowerPAD requires a low-impedance copper connection to the ground plane for electrical and thermal performance. Use short, direct feedback routing and provide local supply bypassing close to the device rather than relying on distant bulk capacitance.
This product page combines the Texas Instruments product information with a practical focus on supply range, bandwidth, slew rate, output drive, package construction, lifecycle status, and design trade-offs. It also organizes same-footprint alternatives so engineers can evaluate replacement candidates against the original THS3091DDA before approving a PCB or production change.
חלופות תחליף ישיר עבור THS3091DDA — אותו מארז, תואם פין-לפין. חלקים במארז שונה הדורשים עיבוד מחדש של ה-PCB אינם נכללים.
THS3092DDAR
✅ Drop-In📋 חלופה להתייחסות (לא בקטלוג)
THS3062DDAG3
✅ Drop-In📋 חלופה להתייחסות (לא בקטלוג)
THS3091DDA דירוגים מרביים ומאפיינים חשמליים
| Amplifier Type | Single current-feedback operational amplifier |
| Number of Circuits | 1 circuit |
| Gain-Bandwidth Product | 180 MHz |
| Total Supply Range | 32 V |
| Nominal Operating Supply Range | ±5 V to ±16 V |
| Slew Rate | 6000 V/μs |
| Output Current | 310 mA |
| Amplifier Architecture | Current feedback |
| Signal Type | Single-ended |
| מארז | 8-pin SOIC PowerPAD |
| סוג הרכבה | Surface mount |
| סטטוס מחזור חיים | No longer in production |
מדריך תצורת פינים של THS3091DDA 8-pin soic powerpad
תצורת פינים עבור THS3091DDA (מארזת 8-pin soic powerpad). רכיב אנלוגי זה כולל פיני כניסה, יציאה ואספקת מתח. יש לעיין בגיליון הנתונים של היצרן לתצורות פיני איפוס היסט, פיצוי והפעלה. אידיאלי למעגלי עיצוב אותות ומגברים.
אין נתוני פריסת פינים מפורטים עבור THS3091DDA.
עיינו ב- גיליון נתונים עבור תצורת פינים מלאה.
יישומים טיפוסיים
THS3091DDA מתאים עבור 6 יישוםs: Semiconductor Pin Test Drivers, Power-FET Gate Drivers, Arbitrary Waveform Generators, VDSL Line-Driver Interfaces, Ultrasonic Test Instrumentation, Low-Resistance Load Test Equipment.
Semiconductor Pin Test Drivers
The THS3091DDA fits semiconductor pin-test systems that must generate large, rapidly changing voltage waveforms at a device terminal. Its 6000 V/μs slew rate supports fast edge transitions, while its output current capability of up to 310 mA gives the driver authority for resistive and capacitive fixture loads. The single-amplifier arrangement simplifies one-channel drive stages and reduces board area. Place the feedback components close to the amplifier and validate settling with the actual cable, socket, and probe capacitance because capacitive loading can affect current-feedback stability. The 8-pin SOIC PowerPAD also provides a practical surface-mount construction for multi-channel test equipment.
מומלץ
Power-FET Gate Drivers
The THS3091DDA is appropriate for power-FET gate-driver circuits requiring a large voltage swing and strong transient current. Its ±5 V to ±16 V supply range supports bipolar drive conditions, and its 6000 V/μs slew rate produces fast gate transitions. The up-to-310-mA output capability helps drive the gate capacitance and minimizes edge distortion. Because FET gate loading is highly dependent on device size and operating frequency, verify peak and continuous current against the selected transistor and the manufacturer datasheet. Keep feedback traces short and provide a low-impedance ground connection beneath the PowerPAD to preserve high-frequency behavior.
מומלץ
Arbitrary Waveform Generators
The THS3091DDA supports the output stage of an arbitrary waveform generator that must produce large linear signals into practical test loads. Its 180 MHz bandwidth and 6000 V/μs slew rate provide a strong combination of signal frequency and transition-rate capability, while the wide supply range increases available output amplitude. The 310 mA drive capability is useful when the generator feeds low-impedance or appreciably capacitive loads. Engineer the feedback network for the target gain because current-feedback amplifiers have gain-dependent bandwidth and stability. Confirm output settling, offset, distortion, and thermal rise with the complete output network rather than a nominal 50-ohm test load alone.
מומלץ
VDSL Line-Driver Interfaces
The THS3091DDA is suitable for VDSL-related line-driver interfaces where large, low-distortion voltage swings are needed. Texas Instruments identifies VDSL line drivers among the intended THS309x applications. The ±5 V to ±16 V supply range, 180 MHz bandwidth, 6000 V/μs slew rate, and output-current capability provide a useful foundation for short-reach or termination networks. Line-driver performance also depends on transformer or balun characteristics, output impedance, isolation requirements, and allowable distortion. Characterize the complete channel because a fast amplifier alone does not guarantee acceptable mask or return-loss performance.
מומלץ
Ultrasonic Test Instrumentation
The THS3091DDA can serve as a high-voltage output amplifier in ultrasonic test and measurement equipment. Its 6000 V/μs slew rate supports low-distortion reproduction of high-frequency bursts, while the broad supply range permits larger transducer excitation voltages than conventional low-voltage operational amplifiers. The output-current capability helps drive transducer and cable capacitance, although the actual limit must be checked for each frequency and load combination. Use short feedback routing, local decoupling, and a carefully controlled ground return to minimize high-frequency coupling. Confirm transducer breakdown voltage, allowable duty cycle, and amplifier thermal dissipation before increasing drive amplitude.
מומלץ
Low-Resistance Load Test Equipment
The THS3091DDA fits measurement equipment that drives low-resistance loads while maintaining large output swings. Its high slew rate limits the transition time needed to reach a commanded voltage, and its current capability provides more drive than a conventional small-signal operational amplifier. These properties make it useful in automated load fixtures and high-speed current or power-device characterization systems. The thermal design must account for sustained voltage and current because dissipation rises with output swing and load. Start with conservative load values, monitor output settling and waveform distortion, and use the manufacturer current-limit and power information to establish safe operating boundaries.
מומלץ
סיכום מוצרים מומלצים
נתוני עזר הנדסיים עבור THS3091DDA — השוואה, הנחיות תכנון ומידע על תאימות.
מדריך בחירה
השוואה עם חלופות
| פרמטר | מוצר זה | THS3092DDAR | THS3062DDAG3 |
|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | 8-pin SOIC PowerPAD | 8-pin SOIC PowerPAD | 8-pin SOIC PowerPAD |
מבדילים עיקריים
- High output-drive capability for a single current-feedback amplifier (לעומתTHS3092DDAR)
- Large bipolar operating range for high-swing output stages (לעומתTHS3062DDAG3)
- 180 MHz bandwidth combined with current-feedback operation (לעומתTHS3092DDAR)
הערות תכנון
Connect the 8-pin SOIC PowerPAD thermal pad to a low-impedance ground plane using multiple vias and adequate copper area. The amplifier dissipates energy whenever its output voltage and load current are both nonzero, and low-resistance loads can produce substantial heating even though the package supports 310 mA output current. Check worst-case continuous dissipation and junction temperature against the manufacturer power limits. Keep thermal copper away from thermally sensitive analog sections where practical, and avoid concentrating heat around nearby precision components.
Use short, direct routing for the inverting input, feedback resistor, and output. Current-feedback amplifiers can become unstable when parasitic capacitance appears in the feedback node or input path. Place the feedback components adjacent to the amplifier pins, keep the non-inverting input route compact, and avoid long traces parallel to the output. Place supply-bypass capacitors close to the supply pins and follow the manufacturer datasheet grounding and decoupling layout for the PowerPAD construction.
Do not assume that the 180 MHz bandwidth is a fixed gain-bandwidth value like that of a voltage-feedback amplifier. The THS3091DDA is a current-feedback device, so bandwidth and stability vary with closed-loop gain and feedback impedance. Recheck stability and settling at every intended gain with the actual load capacitance, cable, probe, and output network. Also verify that peak output current, supply headroom, and package temperature remain within the manufacturer ratings.
The ±5 V to ±16 V supply capability allows large bipolar output swings, but the available output amplitude still depends on the selected supply, load, output-current direction, and voltage margin. Use separate local bypassing for each supply rail and avoid routing return current through the feedback reference. Check the output-stage dissipation for sustained DC output as well as sine-wave operation, because a centered large-amplitude waveform can consume more average power than an equivalent transient workload.
מידע על תאימות
No specific RoHS, REACH, lead-free, halogen-free, or conflict-minerals declarations were identified in the manufacturer information represented for this product. The THS3091DDA is an industrial high-voltage operational amplifier rather than an automotive-qualified device.