THS3125ID - 120MHz High-Output-Current Amplifier | Texas Instruments
MPN: THS3125ID ✓ 啟用中THS3125ID 概覽
A current-feedback operational amplifier is a voltage-input amplifier whose closed-loop bandwidth and gain relationship differ from that of a conventional voltage-feedback amplifier. The THS3125 family belongs to the operational-amplifier hierarchy, where current-feedback amplifiers provide high-speed performance and strong drive capability for demanding analog systems. Its combination of wide bandwidth, high output current, and dual-channel integration makes it suitable for signal chains requiring both bandwidth and load-driving capability.
The primary features include two amplifier channels in one package, a 120 MHz gain-bandwidth product, operation from ±5 V to ±15 V, and a shutdown function. A distributor specification identifies the amplifier as a 450 mA current-feedback device, while another listing describes the THS3125ID variant with approximately 440 mA output current and a 1550 V/µs slew rate. Designers should use the manufacturer datasheet limits for the exact operating conditions before finalizing a design.
The current-feedback architecture is particularly useful in line-driver, motor-driver, and piezo-driver applications. Unlike a voltage-feedback amplifier, it can maintain useful high-frequency behavior at relatively low closed-loop gains, although the feedback resistor selection remains important. The shutdown feature provides a low-current operating state when the system does not need active amplification, helping reduce supply demand in portable or intermittently active equipment.
Typical applications include high-speed line drivers, motor drivers, piezo drivers, video-signal interfaces, and industrial control or instrumentation requiring a high-current output stage. The dual configuration reduces board area when two channels are needed, while the 14-SOIC package supports conventional surface-mount assembly. Supply bypassing, feedback-component placement, and output-load stability require careful layout.
For a new design, verify the required gain, output-voltage swing, load current, and supply voltage against the datasheet before assigning resistors or external passives. The shutdown pin must be driven to the proper logic level, and unused amplifier channels should be configured according to the manufacturer's recommended termination and biasing arrangement.
This product page consolidates the manufacturer specifications, package information, sourcing parameters, replacement guidance, comparison criteria, and practical application notes needed to evaluate the THS3125ID before committing a high-speed analog design to PCB implementation.
直接替換替代品,適用於 THS3125ID — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
此系列的變體
與下列產品可直接替換的同系列型號: THS3125ID (相同外形與佔位) — 差異在於 Amplifier Type, Gain-Bandwidth Product, Package.
THS3115ID
✅ 直接替換聯絡詢價
查看資料表 →THS3122IP
✅ 直接替換 ⚠️ 規格未經驗證📋 參考替代品(不在目錄中)
THS3121IP
✅ 直接替換 ⚠️ 規格未經驗證📋 參考替代品(不在目錄中)
THS3125ID 最大額定值與電氣特性
| Amplifier Type | Current-feedback operational amplifier |
| Number of Channels | 2 channels |
| Gain-Bandwidth Product | 120 MHz |
| 最大輸出電流 | 450 mA |
| Output Current for THS3125ID | 440 mA |
| Slew Rate | 1550 V/µs |
| Supply Voltage Range | ±5 V to ±15 V |
| Supply Current per Channel | 7.2 mA |
| Shutdown Supply Current | 370 µA |
| Shutdown Function | Yes |
| 工作溫度範圍 | -40°C to 85°C |
| 封裝 | 14-SOIC (0.154 inch, 3.90 mm width) |
| 安裝類型 | Surface mount |
| Total Harmonic Distortion | -75 dBc at 8 VPP |
THS3125ID 14-soic (0.154 inch, 3.90 mm width) 腳位配置指南
THS3125ID(14-soic (0.154 inch, 3.90 mm width) 封裝)的腳位配置。 此類比元件具有輸入、輸出與電源腳位。偏移歸零、補償與致能腳位配置請參閱製造商資料表。適用於訊號調理與放大器電路。
無詳細腳位定義資料: THS3125ID.
請參閱 資料表 以查看完整腳位配置。
典型應用
THS3125ID 適用於 6 應用s: High-Speed Line Driver, Motor Drive Signal Conditioning, Piezo Driver Interface, Video Signal Interface, Industrial Instrumentation, Portable High-Speed Interface.
High-Speed Line Driver
The THS3125ID suits high-speed line-driver circuits because the dual current-feedback amplifiers provide a 120 MHz family bandwidth with high output-current capability in a 14-SOIC package. The high-drive output can support low-impedance or terminated lines more effectively than a conventional low-current op amp. Design the feedback network around the current-feedback topology, use short output paths, and verify the output swing at the actual load. Shutdown can reduce supply demand when the driven line must be inactive.
推薦
Motor Drive Signal Conditioning
The THS3125ID can condition position, current, and feedback signals in motor-control systems while providing the high output drive required by downstream stages. Its dual architecture supports two independent control or sensing channels, and the 120 MHz bandwidth preserves fast edges. The family is also identified for motor-driver use, supporting operation with bipolar supplies from ±5 V to ±15 V. Validate output swing, load current, stability, and thermal behavior against the motor-driver circuitry and protection network.
推薦
Piezo Driver Interface
For piezo positioning and ultrasonic-drive systems, the THS3125ID combines a 120 MHz family bandwidth with approximately 440 mA listed output-current capability for the exact suffix. This combination helps preserve fast drive waveforms across capacitive loads. The shutdown function can place the amplifier in a 370 µA low-current state when the actuator is idle. Because piezo loads are capacitive, include current limiting and output protection, and confirm oscillation and stability with the complete feedback and load network.
推薦
Video Signal Interface
The THS3125ID can serve as a high-speed dual video-buffer or line-interface stage where 120 MHz bandwidth and strong output drive are more important than very low offset or bias-current performance. The two channels reduce the number of active devices needed for paired video paths, while the shutdown input offers a way to disable amplification when required. Keep feedback traces short, provide local supply bypassing, and verify output amplitude, load impedance, and settling behavior with the selected video standard.
推薦
Industrial Instrumentation
The THS3125ID fits instrumentation front ends that need wide bandwidth and the ability to drive downstream analog circuitry without adding separate buffer stages. Its dual-channel configuration can handle complementary or sequential signal paths, and the 120 MHz family bandwidth supports fast transient capture and control signals. The -40°C to 85°C operating range covers industrial environments, while shutdown can reduce consumption during idle measurement cycles. Validate noise, offset, stability, and output accuracy for the required measurement bandwidth.
推薦
Portable High-Speed Interface
The THS3125ID can support a compact dual-channel interface in portable or intermittently powered equipment because each channel draws as little as 7.2 mA and shutdown reduces supply current to 370 µA. Its 14-SOIC package simplifies surface-mount assembly while retaining high bandwidth and strong drive capability. Account for the added heat generated when driving low-impedance loads, use local decoupling on both supplies, and ensure the shutdown control remains in a defined state during startup and power-loss events.
推薦
推薦產品摘要
工程參考資料,適用於 THS3125ID — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | THS3115ID | THS3122IP | THS3121IP |
|---|---|---|---|---|
| Package | 14-SOIC | 14-SOIC | 14-SOIC | 14-SOIC |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Number of Channels | 2 | 2 | 2 | 2 |
主要差異化特點
- Higher output-drive capability within the compared package options (對比THS3115ID)
- Integrated shutdown control (對比THS3122IP)
- Dual-channel integration in a standard 14-SOIC package (對比THS3121IP)
設計說明
Place the feedback resistor and feedback capacitor directly between the amplifier output and inverting input, and keep the inverting-input node physically short. Current-feedback amplifiers are sensitive to parasitic capacitance at the summing node because excess capacitance can alter gain and encourage instability. Route the output away from the feedback and input nodes, use a compact ground return, and avoid long traces beneath or beside high-speed input and feedback paths.
Use local high-frequency decoupling on each supply pin and place the capacitors close to the device rather than at the connector or regulator. Separate the supply-current return path from sensitive input grounding where practical. Because the amplifier can dissipate substantial heat while driving a low-impedance load, estimate conduction and crossover losses using the actual output waveform, supply voltage, load resistance, and duty cycle. Confirm the resulting junction temperature against the manufacturer rating.
Do not assume that a conventional voltage-feedback amplifier's resistor values will work with the THS3125ID. Select feedback components according to the manufacturer's current-feedback application guidance and the intended gain. Also, verify that the shutdown logic remains compatible with the system control sequence. The 370 µA shutdown figure is a low-power state, not a guarantee that every external node becomes electrically safe or that the outputs immediately reach a defined state.
Analyze the complete output network rather than only the amplifier gain. Cable capacitance, input capacitance, connector inductance, and load impedance can change bandwidth and stability. For long or high-speed interconnects, use controlled-impedance routing, minimize stub lengths, and place suitable termination close to the receiving device. Evaluate rise time and overshoot with the actual source, amplifier, and load combination before treating the nominal 120 MHz bandwidth as usable system bandwidth.
合規資訊
No explicit compliance declarations were identified for THS3125ID. Confirm RoHS, REACH, lead-free, halogen-free, and conflict-minerals status using the current Texas Instruments product and quality documentation before regulatory submission.