THS4021CD - 350 MHz Low-Noise VFA | TI | Imaging
MPN: THS4021CD ✓ 啟用中THS4021CD 概覽
A voltage-feedback amplifier is a feedback-controlled amplifier category that uses voltage-mode feedback to balance gain and bandwidth. Voltage-feedback amplifiers belong to the broader operational-amplifier and analog-signal-processing hierarchy. Compared with current-feedback amplifiers, they offer a conventional differential-input topology and are widely used for precision gain, impedance conversion, waveform shaping, and signal buffering where the required operating bandwidth is compatible with the amplifier's gain-bandwidth behavior.
The THS4021CD combines a 350 MHz small-signal bandwidth with a 470 V/us slew rate, allowing it to reproduce rapidly changing analog signals while limiting slew-rate distortion. Its ultra-low-noise design targets applications in which amplifier-generated noise can obscure the signal under analysis. The single-channel configuration also reduces board area compared with a dual amplifier when only one high-speed signal path is required. The device is available in the compact 8-SOIC surface-mount package identified by the CD ordering code.
Its voltage-feedback architecture supports precise analog signal conditioning in closed-loop systems. The combination of wide bandwidth and high slew rate is important when handling fast edges, pulse-like waveforms, or high-frequency small-signal measurements. Because the component is intended for noise-sensitive paths, PCB layout, grounding, power bypassing, and control of parasitic capacitance can materially affect achieved performance. Signal routing should be short and symmetric, while supply connections should use a low-impedance return path.
Typical applications include communications receivers, medical and industrial imaging, oscilloscope input paths, high-speed instrumentation, active filtering, and general-purpose high-speed buffers. The device is also appropriate wherever a single analog channel must preserve signal fidelity across a substantially wider frequency range than conventional general-purpose amplifiers can support. For very low-amplitude signals, designers should evaluate input-referred noise, source impedance, gain settings, and the bandwidth required by the measurement before finalizing the signal chain.
A critical design consideration is that high-speed operation makes board construction and grounding part of the circuit. Place power-bypass capacitors close to the supply pins, maintain a continuous ground reference, avoid long input and feedback traces, and use controlled-impedance routing when signal rates are high. Gain-setting resistors and compensation components should be positioned close to the relevant amplifier pins to minimize parasitic effects that can alter bandwidth, stability, or pulse response.
This product page combines the exact manufacturer and distributor specifications with a practical THS4021CD pin and footprint assessment, application guidance, design considerations, and a conservative drop-in replacement review. It also distinguishes verified same-footprint ordering variants from alternatives that require a package or functional change, helping engineers make a replacement decision without assuming that a similar high-speed amplifier is electrically interchangeable.
直接替換替代品,適用於 THS4021CD — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
此系列的變體
與下列產品可直接替換的同系列型號: THS4021CD (相同外形與佔位) — 差異在於 Package, Amplifier Type, Slew Rate, Number of Channels, Supply Voltage Range.
THS4021IDG4
✅ 直接替換📋 參考替代品(不在目錄中)
THS4021IDR
✅ 直接替換📋 參考替代品(不在目錄中)
THS4021CDR
✅ 直接替換📋 參考替代品(不在目錄中)
THS4031IDR
✅ 直接替換聯絡詢價
查看資料表 →THS4021IP
✅ 直接替換 ⚠️ 規格未經驗證📋 參考替代品(不在目錄中)
THS4021CD 最大額定值與電氣特性
| Amplifier Type | Voltage-feedback amplifier |
| Channel Count | 1 channel |
| Small-Signal Bandwidth | 350 MHz |
| Slew Rate | 470 V/us |
| Supply Voltage Range | plus or minus 16 V, or 32 V total |
| 封裝 | 8-pin SOIC, 0.154 inch body width, 3.90 mm |
| 安裝類型 | Surface mount |
| Operating Supply Range | plus or minus 16 V |
THS4021CD 8-pin soic, 0.154 inch body width, 3.90 mm 腳位配置指南
THS4021CD(8-pin soic, 0.154 inch body width, 3.90 mm 封裝)的腳位配置。 此類比元件具有輸入、輸出與電源腳位。偏移歸零、補償與致能腳位配置請參閱製造商資料表。適用於訊號調理與放大器電路。
無詳細腳位定義資料: THS4021CD.
請參閱 資料表 以查看完整腳位配置。
典型應用
THS4021CD 適用於 6 應用s: Communications Signal Conditioning, Medical and Industrial Imaging, High-Speed Instrumentation, Oscilloscope and Test Signal Paths, Active Filtering and Waveform Conditioning, High-Speed Signal Buffering.
Communications Signal Conditioning
The THS4021CD fits communications signal-conditioning stages that require a single high-speed analog channel with low voltage noise. Its 350 MHz bandwidth and 470 V/us slew rate provide margin for fast edges and higher-frequency signal content while preserving a conventional voltage-feedback topology. The amplifier can be placed before a downstream converter or receiver input when the required gain, source impedance, and output amplitude are compatible with the closed-loop response. Because high-speed operation magnifies routing and grounding defects, use short traces, a solid ground reference, and close supply bypassing. The key design trade-off is bandwidth versus power and noise: a wider amplifier does not automatically improve the complete receiver if quantization, filtering, or antenna constraints dominate.
推薦
Medical and Industrial Imaging
The THS4021CD is appropriate for imaging front ends that need to amplify rapidly changing sensor or electrode signals without adding excessive voltage noise. Its 350 MHz bandwidth and 470 V/us slew rate support high-bandwidth analog paths, including sensor readout and preamplifier stages operating at moderate or high gain. The single-channel format is useful where only one signal must be conditioned close to the sensor, reducing routing between amplifier stages. Designers should account for sensor capacitance, cable length, gain-bandwidth requirements, and output-swing limits. High-speed layout is essential: return the feedback components close to the pins, avoid long traces around the sensitive input, and provide local bypass capacitance to prevent supply impedance from disturbing the signal.
推薦
High-Speed Instrumentation
The THS4021CD can be used in instrumentation requiring wider bandwidth than conventional precision amplifiers provide. Its 350 MHz bandwidth makes it useful for buffer and active-filter stages handling fast transients, while the 470 V/us slew rate reduces the likelihood of slew-rate limiting on demanding edges. Instrumentation designs should still verify input noise, offset, bias current, and output-current limits against the measurement bandwidth and source resistance. Keep the feedback network compact and terminate unused channels according to the manufacturer guidance rather than leaving high-impedance inputs floating. The performance trade-off is that a high-speed amplifier may consume more power and provide less precision near DC than a dedicated precision op amp.
推薦
Oscilloscope and Test Signal Paths
The THS4021CD is suitable for high-speed test and measurement paths that must amplify pulses, edges, or low-amplitude waveforms without obvious bandwidth limitation. The combination of 350 MHz small-signal bandwidth and 470 V/us slew rate allows it to preserve rapid transitions when operated at a compatible gain and load. In a measurement instrument, the amplifier may buffer a source, drive a converter, or form an active analog filter. Check the source impedance and capacitive loading because they can interact with the feedback network and alter stability or pulse shape. Use short, controlled-impedance interconnects and decouple each supply rail near the device to maintain predictable behavior across the complete measurement bandwidth.
推薦
Active Filtering and Waveform Conditioning
The THS4021CD can implement high-speed active filters or waveform-conditioning stages because its 350 MHz bandwidth and 470 V/us slew rate provide response beyond the range of many general-purpose amplifiers. It is particularly relevant when filtering or shaping fast pulses while keeping rise times and transient behavior predictable. Component tolerances, parasitic capacitance, and amplifier stability become more important as operating frequency increases, so the feedback and compensation parts should be placed directly beside the relevant pins. Evaluate the complete filter response rather than relying only on nominal bandwidth. The device trades low-level precision for speed, making it more appropriate for signal-shape enhancement than for demanding DC or low-frequency measurements.
推薦
High-Speed Signal Buffering
The THS4021CD is useful as a single-channel buffer when driving downstream circuitry through a cable, connector, converter input, or another stage with appreciable capacitive loading. Its 350 MHz bandwidth and 470 V/us slew rate provide more than enough response for many high-speed signals, while the voltage-feedback configuration supports conventional feedback compensation. Output loading and stability must be checked with the actual source and sink, including cable capacitance and connector parasitics. Keep output routing short, provide a nearby return path, and avoid excessive feedback capacitance that can reduce bandwidth or cause peaking. When low-frequency precision dominates and bandwidth is unnecessary, a lower-power precision amplifier may offer a better overall efficiency and accuracy tradeoff.
推薦
工程參考資料,適用於 THS4021CD — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 |
|---|---|
| Brand | Texas Instruments |
| Package | 8-SOIC |
| Amplifier Type | Voltage-feedback amplifier |
| Channel Count | 1 channel |
| Bandwidth | 350 MHz |
| Slew Rate | 470 V/us |
| Supply Voltage | plus or minus 16 V |
| Noise Class | Ultra-low voltage noise |
| Primary Applications | Communications, imaging, instrumentation, and buffering |
主要差異化特點
- High-speed performance combined with ultra-low-noise positioning (對比General-purpose 8-pin SOIC amplifiers)
- Single-channel implementation in a compact 8-SOIC package (對比Dual-channel high-speed amplifier packages)
- Wide high-speed operating capability (對比Lower-bandwidth precision amplifiers)
設計說明
Treat the PCB as part of the high-speed circuit. Place input, feedback, and compensation components directly beside their associated amplifier pins, and avoid routing the sensitive input over split or shared return paths. Keep traces short, use a continuous ground plane, and avoid adding test-point stubs that create unnecessary capacitance. Because the device offers 350 MHz bandwidth and 470 V/us slew rate, interconnect parasitics can affect stability and transient response even when the schematic appears correct.
Use low-impedance local decoupling for each supply connection and keep the bypass capacitor and its return path as close to the device as practical. The verified operating range extends to plus or minus 16 V, but allowable input common-mode and output swing must remain within the manufacturer limits for the selected signal and gain. Confirm the source rails’ impedance at high frequency and use a stable reference or filtering arrangement if the amplifier shares supply infrastructure with fast digital circuitry.
Do not select the amplifier from bandwidth alone. Match the closed-loop gain, feedback impedance, source impedance, capacitive load, and required output amplitude, then verify noise and stability over the intended frequency range. A 470 V/us slew rate cannot compensate for excessive gain, overloaded outputs, or an unsuitable gain-setting network. Confirm the complete signal chain in simulation or measurement before production release.
合規資訊
The verified product information does not provide explicit RoHS, REACH, lead-free, halogen-free, or conflict-minerals statements. The THS4021CD is an operational amplifier rather than an automotive-qualified device, so AEC-Q100 is marked not applicable.