TJA1028TK/5V0/20/J - 5V LIN Transceiver 8-HVSON | NXP
MPN: TJA1028TK/5V0/20/J ✓ 啟用中TJA1028TK/5V0/20/J 概覽
A LIN transceiver, also called a LIN interface controller or LIN system-basis chip, converts logic-level serial data between a microcontroller and a low-cost single-wire vehicle network. The TJA1028 combines bus-level receive and transmit functions with a local regulator, allowing a compact LIN node to power its host microcontroller or peripheral circuitry while communicating over the vehicle network.
The principal features include a 5.0 V regulator output, regulator capability of up to 70 mA, LIN 2.0 and LIN 2.1 compatibility, SAE J2602 and ISO 17987-4:2016 12 V compliance, and strong electrostatic-discharge robustness. The 3 x 3 mm HVSON package includes an exposed pad for improved heat transfer when the integrated regulator dissipates power.
The TJA1028 architecture is tailored to low-speed automotive and industrial LIN networks. Its integrated regulator reduces the number of discrete components needed for a basic LIN slave node, while the 8-pin package supports compact PCB placement. The product family is also offered in 3.3 V and 5.0 V regulator variants, allowing the interface voltage to match different host systems.
Typical uses include LIN-controlled vehicle modules, body-control electronics, sensor interfaces, door and seat modules, climate-control peripherals, and compact industrial LIN nodes. The device is particularly suitable when a local 5 V rail is required alongside LIN communications and board space is tightly constrained.
Use the manufacturer datasheet pin description and application circuit when assigning PCB tracks, decoupling, exposed-pad connections and bus protection. Confirm that the selected 5 V variant matches the host supply requirements and that the regulator load remains within the specified 70 mA capability.
This page combines the TJA1028 family specifications, package details, supported LIN standards and same-footprint ordering variants with practical guidance for PCB implementation, sourcing and design selection.
直接替換替代品,適用於 TJA1028TK/5V0/20/J — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
TJA1028TK/5V0/20/1
✅ 直接替換📋 參考替代品(不在目錄中)
TJA1028TK/5V0/20/X
✅ 直接替換📋 參考替代品(不在目錄中)
TJA1028TK/5V0/20/J 規格
| Product Type | Single-channel LIN transceiver with integrated voltage regulator |
| LIN Bus Compatibility | LIN 2.0 and LIN 2.1 |
| Automotive Network Compliance | SAE J2602 and ISO 17987-4:2016 for 12 V networks |
| Integrated Regulator Output | 5.0 V |
| Integrated Regulator Current | Up to 70 mA |
| Regulator Architecture | Low-dropout voltage regulator |
| 封裝 | 8-pin HVSON, 3 x 3 mm |
| 安裝類型 | Surface mount |
| Transceiver Configuration | 1 transmitter and 1 receiver |
| ESD Robustness | Strong electrostatic-discharge performance |
| LIN Bus Voltage Class | 12 V |
| Packing | 13-inch tape-and-reel |
| Maximum Supply Voltage | 5.1 V |
| Minimum Supply Voltage | 4.9 V |
| Maximum Supply Current | 4.5 mA |
| Automotive Qualification | AEC-Q100 |
TJA1028TK/5V0/20/J 8-pin hvson, 3 x 3 mm 腳位配置指南
TJA1028TK/5V0/20/J(8-pin hvson, 3 x 3 mm 封裝)的腳位配置。 腳位編號、功能與連接圖定義於製造商資料手冊中。請參閱該手冊以取得確切的封裝尺寸與焊接指引。
無詳細腳位定義資料: TJA1028TK/5V0/20/J.
請參閱 資料表 以查看完整腳位配置。
典型應用
TJA1028TK/5V0/20/J 適用於 6 應用s: Automotive LIN Body-Control Nodes, Vehicle Sensor Interface Modules, Door and Seat Control Modules, Climate-Control Peripheral Interfaces, Industrial LIN Slave Modules, Compact LIN Actuator Controllers.
Automotive LIN Body-Control Nodes
The TJA1028TK/5V0/20/J fits compact automotive body-control modules that communicate over a LIN subnetwork and need a local 5 V supply. Its LIN 2.0 and LIN 2.1 compatibility, SAE J2602 alignment and ISO 17987-4:2016 support establish the interface behavior for 12 V vehicle networks. The integrated regulator supplies up to 70 mA, while the 8-pin HVSON package reduces PCB area compared with separate transceiver and regulator arrangements. Designers should allocate exposed-pad copper and place local decoupling near the device to preserve regulator stability and thermal performance.
推薦
Vehicle Sensor Interface Modules
The TJA1028TK/5V0/20/J is useful in LIN-connected sensor modules where the remote node combines communication and a small regulated load. The 5.0 V variant can power compatible sensing or interface circuitry up to the regulator's 70 mA capability without requiring a separate low-drop regulator. LIN 2.0 and 2.1 support provides a standardized physical layer for inexpensive single-wire networking. The compact 3 x 3 mm HVSON package is particularly valuable when the sensor assembly has limited board area, although the LIN bus and ground return still require robust vehicle-network layout practices.
推薦
Door and Seat Control Modules
Door locks, seat controls and related distributed vehicle modules commonly use LIN for low-cost communication with a central body controller. The TJA1028TK/5V0/20/J combines a LIN transceiver with a 5.0 V regulator capable of delivering up to 70 mA, allowing a compact slave node to support its host logic and local actuator interface. Its compliance with LIN 2.0, LIN 2.1, SAE J2602 and ISO 17987-4:2016 supports integration into 12 V LIN systems. The exposed-pad package requires careful PCB thermal design if the regulator operates near its current limit.
推薦
Climate-Control Peripheral Interfaces
The TJA1028TK/5V0/20/J can serve as the network interface for compact climate-control peripherals that use a LIN command bus. The 5.0 V regulator provides up to 70 mA for a small local control or sensing section, while the integrated transceiver reduces the component count of the communication path. Compliance with LIN 2.0, LIN 2.1 and the cited 12 V automotive network standards makes the device suitable for distributed vehicle electronics. Layout should separate sensitive control circuitry from LIN and supply-return paths where practical.
推薦
Industrial LIN Slave Modules
The TJA1028TK/5V0/20/J can be used in industrial LIN slave modules that need a standardized single-wire interface and a local 5 V rail. Although the family is designed around automotive LIN networks, its LIN 2.0, LIN 2.1, SAE J2602 and ISO 17987-4:2016 compatibility provides a defined bus interface. The integrated regulator eliminates a separate regulator when the peripheral load is no more than 70 mA. Designers should verify EMC, transient and wiring requirements for the final industrial installation before approving the device.
推薦
Compact LIN Actuator Controllers
The TJA1028TK/5V0/20/J fits compact actuator controllers where a LIN command interface and regulated local supply share one package. Its 70 mA regulator capability can support control logic and limited peripheral circuitry, while the small 8-pin HVSON footprint preserves board area around the actuator driver. The device's LIN 2.0 and 2.1 behavior and stated 12 V network compliance support robust distributed control. The PCB should implement the manufacturer land pattern, exposed-pad connection and decoupling arrangement to maintain reliable regulation and thermal performance.
推薦
推薦產品摘要
工程參考資料,適用於 TJA1028TK/5V0/20/J — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | TJA1028TK/5V0/20/1 | TJA1028TK/5V0/20/X |
|---|---|---|---|
| Package | HVSON-8 (3 x 3 mm) with exposed pad | HVSON-8 (3 x 3 mm) with exposed pad | HVSON-8 (3 x 3 mm) with exposed pad |
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Product Type | Single-channel LIN transceiver with integrated voltage regulator | Single-channel LIN transceiver with integrated voltage regulator | Single-channel LIN transceiver with integrated voltage regulator |
| Integrated Regulator Output | 5.0 V | 5.0 V | 5.0 V |
| Regulator Output Current | Up to 70 mA | Up to 70 mA for the TJA1028 family | Up to 70 mA for the TJA1028 family |
| LIN Compatibility | LIN 2.0 and LIN 2.1 | LIN 2.0 and LIN 2.1 | LIN 2.0 and LIN 2.1 |
| Automotive Network Compliance | SAE J2602 and ISO 17987-4:2016 for 12 V | SAE J2602 and ISO 17987-4:2016 for 12 V | SAE J2602 and ISO 17987-4:2016 for 12 V |
| Ordering and Packing | /J, 13-inch tape and reel | /1, documented as identical 13-inch tape-and-reel packing | /X ordering suffix |
主要差異化特點
- Combines LIN communication and a local 5.0 V supply in one package (對比TJA1028TK/5V0/20/1)
- Uses the same documented 13-inch tape-and-reel presentation as the /1 ordering code (對比TJA1028TK/5V0/20/1)
- Maintains the same integrated-rail architecture across available ordering suffixes (對比TJA1028TK/5V0/20/X)
設計說明
Implement the manufacturer HVSON-8 land pattern and connect the exposed pad to the recommended ground plane with adequate via coverage. Place input and output capacitors close to their corresponding pins, and minimize the distance between the LIN transceiver return path and the device ground reference. The 3 x 3 mm package saves area, but its exposed pad is important for both electrical stability and heat removal.
Estimated regulator dissipation equals the voltage difference between the input supply and the 5.0 V output multiplied by the load current. For example, using a 5.1 V input, a 5.0 V output and a 40 mA load gives approximately 0.004 W because the available voltage drop is only 0.1 V. Use the actual minimum input voltage, maximum output voltage and highest operating load for the worst-case thermal assessment, and provide copper beneath the exposed pad.
Do not treat TJA1028TK/5V0/20/1 or TJA1028TK/5V0/20/X as different electrical regulators merely because their ordering suffixes differ. Conversely, do not substitute the 3.3 V family variant into a design that requires 5.0 V. Confirm the complete orderable MPN, regulator output, package, exposed-pad treatment and packing requirements before releasing a production BOM.
Route the LIN connection as a controlled bus with the shortest practical path to the connector or network interface. Keep the regulator and digital return path compact, and follow the recommended grounding and capacitor arrangement from the NXP datasheet. LIN is a single-wire network, so bus topology, termination practices and protection requirements should be evaluated at the vehicle or system level rather than handled solely within the transceiver footprint.
合規資訊
A product listing identifies the TJA1028TK/5V0/20/J as AEC-Q100 automotive qualified. RoHS, REACH, lead-free, halogen-free and conflict-minerals declarations were not included in the supplied manufacturer information.