TLV2455IN - 4-Channel 6V 220kHz RRIO Op Amp | Texas Instruments
MPN: TLV2455IN ✓ 啟用中TLV2455IN 概覽
An operational amplifier is an analog signal-processing IC that compares its inverting and non-inverting inputs and amplifies the voltage difference between them. The TLV2455IN belongs to the low-dropout linear-amplifier family of voltage-feedback operational amplifiers, combining rail-to-rail input and output operation with low supply current. Rail-to-rail input capability supports sensing signals near the supply rails, while rail-to-rail output allows the output voltage to approach either supply limit within the device's operating limits.
The principal electrical characteristics are a 220 kHz gain-bandwidth product, 23 µA typical quiescent current per channel, a 6 V supply rating, rail-to-rail input and output operation, a shutdown function, and 20 µV typical input offset voltage. The 220 kHz bandwidth supports moderate-frequency amplification and active filtering, while the four-channel configuration is useful for sensor buffers, differential stages, and multi-axis signal processing.
Each amplifier can be configured with external resistors for noninverting, inverting, differential, filtering, or gain-control circuits. The low quiescent current is particularly valuable in battery-powered equipment where every amplifier channel contributes continuously to system power consumption. The shutdown feature can also reduce consumption when the analog section is not required, provided the enable logic and supply states meet the manufacturer's operating requirements.
Typical uses include portable instrumentation, low-voltage sensor interfaces, audio and control-signal conditioning, active filters, and four-channel acquisition front ends. When designing the board, place each amplifier's feedback components close to its pins, keep input and output traces short, provide suitable bypassing at the supply pins, and avoid placing sensitive high-impedance inputs next to switching or high-current return paths.
This product page combines manufacturer specifications, an electrically equivalent same-package option, application guidance, and package-aware design considerations. It helps engineers distinguish the TLV2455IN's shutdown-enabled function from other quad amplifier variants and plan a direct replacement without changing the 16-pin DIP footprint.
直接替換替代品,適用於 TLV2455IN — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
此系列的變體
與下列產品可直接替換的同系列型號: TLV2455IN (相同外形與佔位) — 差異在於 Amplifier Type.
TLV2455IN 最大額定值與電氣特性
| Number of Amplifier Channels | 4 channels |
| Amplifier Type | General-purpose operational amplifier |
| Supply Voltage Rating | 6 V |
| Gain-Bandwidth Product | 220 kHz |
| Quiescent Current per Channel | 23 µA typical |
| Input Offset Voltage | 20 µV typical |
| Input Common-Mode Range | Rail-to-rail |
| Output Swing | Rail-to-rail |
| Shutdown Function | Yes |
| 封裝 | 16-pin DIP (16-PDIP) |
| 安裝類型 | Through-hole |
TLV2455IN 16-pin dip (16-pdip) 腳位配置指南
TLV2455IN(16-pin dip (16-pdip) 封裝)的腳位配置。 此類比元件具有輸入、輸出與電源腳位。偏移歸零、補償與致能腳位配置請參閱製造商資料表。適用於訊號調理與放大器電路。
無詳細腳位定義資料: TLV2455IN.
請參閱 資料表 以查看完整腳位配置。
典型應用
TLV2455IN 適用於 6 應用s: Portable Sensor Signal Conditioning, Low-Voltage Active Filters, Multi-Axis Instrumentation, Battery-Powered Data Acquisition, Audio and Control Signal Conditioning, Industrial Process Measurement.
Portable Sensor Signal Conditioning
The TLV2455IN fits portable sensor front ends because its four channels provide rail-to-rail input and output operation while each amplifier consumes 23 µA typical quiescent current. Place the device close to the sensor interface and use one channel for buffering, another for gain, and the remaining channels for filtering or reference conditioning. Its 220 kHz gain-bandwidth product handles moderate-bandwidth sensor signals, but engineers should confirm input bias current and offset behavior against the sensor's source impedance. The 16-PDIP package also makes the part suitable for through-hole prototypes and industrial assembly fixtures.
推薦
Low-Voltage Active Filters
The TLV2455IN is useful for multiple active-filter stages because four independent amplifiers are integrated into one 16-pin DIP package. Its 220 kHz gain-bandwidth product supports filter sections operating well below the device's upper small-signal bandwidth, while rail-to-rail input and output behavior improves dynamic range in low-voltage systems. Designers can implement cascaded single-pole, multiple-feedback, or state-variable filters, subject to the final gain and stability requirements. External resistor accuracy and the amplifier's offset, slew rate, and output-drive limits should be evaluated during simulation.
推薦
Multi-Axis Instrumentation
The TLV2455IN suits multi-axis instrumentation where several low-bandwidth analog channels must be amplified near the system supply rails. Four channels in one package reduce the number of separate amplifier components and simplify power-distribution design. The rail-to-rail input range supports sensing close to the supply limits, and the 220 kHz gain-bandwidth product is suitable for many position, force, and motion-sensor signals after appropriate filtering. Use matched resistors when channel gain consistency matters, and verify bias-current effects for high-impedance sensor sources before finalizing the input network.
推薦
Battery-Powered Data Acquisition
The TLV2455IN supports battery-powered data-acquisition systems by combining four amplifier channels with 23 µA typical quiescent current per channel. Rail-to-rail input and output operation allows the circuit to use a limited supply range efficiently, and the shutdown feature can lower consumption when acquisition stops. Use the channels to amplify and filter several inputs without distributing power across four separate packages. Account for load current and output activity in the overall battery budget, and consult the manufacturer datasheet for the exact enable-state behavior and supply conditions before sequencing the analog system.
推薦
Audio and Control Signal Conditioning
The TLV2455IN can condition low-frequency audio, control, or feedback signals in compact multi-channel analog circuits. Its rail-to-rail I/O operation helps preserve signal range in low-voltage equipment, while four channels allow simultaneous handling of monitoring, drive, and feedback paths. The 220 kHz gain-bandwidth product is appropriate for many control and audio-bandwidth signals rather than high-frequency line audio. Validate output swing into the intended load, confirm slew-rate requirements during large-signal transitions, and keep the shutdown state inactive whenever the monitored signals must remain continuous.
推薦
Industrial Process Measurement
The TLV2455IN fits industrial process-measurement modules that acquire several low-bandwidth sensor channels from a common low-voltage supply. Four channels in one 16-PDIP package support channel buffering, differential conversion, filtering, and scaling while retaining rail-to-rail signal range. The 23 µA typical quiescent current per channel supports low-power distributed measurement nodes, and shutdown can assist duty-cycled operation. Validate the production temperature grade, common-mode limits, input bias current, and output capability against the specific transducer and process-control requirements before deployment.
推薦
推薦產品摘要
工程參考資料,適用於 TLV2455IN — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | TLV2455CN |
|---|---|---|
| Brand | Texas Instruments | Texas Instruments |
| Package | 16-pin DIP (16-PDIP) | 16-DIP - same package |
| Number of Amplifier Channels | 4 channels | 4 channels |
| Supply Voltage Rating | 6 V | 6 V |
| Gain-Bandwidth Product | 220 kHz | 220 kHz |
| Quiescent Current per Channel | 23 µA typical | 23 µA typical |
| Input Common-Mode Range | Rail-to-rail | Rail-to-rail |
| Output Swing | Rail-to-rail | Rail-to-rail |
| Shutdown Function | Yes | Yes |
主要差異化特點
- Four channels in one low-power amplifier package (對比TLV2455CN)
- Rail-to-rail signal range in a 16-pin DIP (對比TLV2455CN)
- Shutdown-capable low-power operation (對比TLV2455CN)
設計說明
Route each amplifier's high-impedance input directly to its pin and place feedback resistors close to the corresponding amplifier inputs and outputs. Keep the 16-PDIP footprint free of unintended copper keepouts around the shutdown and supply pins, and provide a clean ground reference for all four channels. Because the device is intended for low-voltage instrumentation, long parallel input traces can increase coupling from adjacent digital or switching nodes.
Decouple the supply pins with local high-frequency bypass capacitance and add bulk capacitance near the power entry according to the manufacturer's recommended circuit. The family is specified at 23 µA typical quiescent current per channel, but the actual supply current also rises with output activity and load. Do not infer the absolute maximum supply voltage from the 6 V family rating; use the datasheet electrical limits when designing transient protection and power-source headroom.
Confirm the exact shutdown polarity, enable thresholds, and permitted supply states before using the shutdown function in a power-sequencing scheme. A shutdown command does not guarantee that every output will reach a defined state in every circuit. Maintain the required logic levels throughout startup and verify output behavior with the actual feedback network, especially when the amplifier drives a load that can back-power the output during shutdown.
Check the selected closed-loop gain against the 220 kHz gain-bandwidth product and use the manufacturer's stability guidance when operating near unity gain or driving capacitive loads. For sensor inputs, compare the sensor impedance with the amplifier's input-bias-current requirement and add filtering only where its added noise and phase impact remain acceptable. Simulate the complete signal path rather than evaluating each amplifier channel in isolation.
合規資訊
The manufacturer product page identifies the TLV2455 family and ordering information, but the verified excerpts do not explicitly state RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals status.