TLV2460CP - 6.4MHz RRIO Op Amp with Shutdown | TI
MPN: TLV2460CP ✓ 啟用中TLV2460CP 概覽
An operational amplifier is an analog integrated circuit that uses high-gain feedback to amplify a differential input voltage. The TLV2460CP belongs to the rail-to-rail input/output amplifier category, allowing its input and output operation to extend toward the supply rails. Within the broader hierarchy, it is an operational amplifier, analog amplifier IC, and signal-conditioning semiconductor designed for low-voltage systems.
The TLV2460CP combines a single amplifier with rail-to-rail input and output capability, a 6.4 MHz gain-bandwidth product, and shutdown support. Its shutdown control can place the amplifier in a low-power state when signal processing is not required, helping reduce system consumption in portable equipment. The device is identified as a single 6 V, 6.4 MHz RRIO amplifier with shutdown by the Texas Instruments product page.
Its rail-to-rail input characteristic is important for signal sources whose voltage swings approach either supply rail, while rail-to-rail output improves voltage headroom when driving a load at low supply voltages. The 6.4 MHz bandwidth supports applications requiring higher closed-loop bandwidth than a general-purpose low-frequency amplifier, although stable operation still depends on the selected feedback topology, noise gain, output loading, and compensation network.
Typical uses include low-voltage sensor conditioning, portable test equipment, audio and communication signal paths, instrumentation buffering, and active filtering. The shutdown function is useful in battery-powered or intermittently operated systems where the amplifier must be disabled between measurement intervals. Rail-to-rail operation also makes the device applicable to systems in which the signal range occupies a substantial portion of the available supply voltage.
Designers should verify the shutdown-pin polarity, input common-mode limits, output swing, stability requirements, and recommended capacitor values in the manufacturer datasheet before finalizing a PCB. Because this is an 8-pin PDIP rather than a surface-mount package, it is best suited to designs that prioritize easy inspection, prototyping, or through-hole assembly over compact board area.
This page organizes the TLV2460CP identity, package, verified electrical highlights, sourcing questions, compatible family options, comparison parameters, and practical design guidance into one engineering reference. It also distinguishes confirmed manufacturer information from characteristics that require confirmation in the complete datasheet before production release.
直接替換替代品,適用於 TLV2460CP — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
TLV2460CPE4
✅ 直接替換📋 參考替代品(不在目錄中)
TLV2460IPE4
✅ 直接替換📋 參考替代品(不在目錄中)
TLV2460CP 最大額定值與電氣特性
| Amplifier Type | Single operational amplifier |
| Technology | CMOS |
| Maximum Supply Voltage | 6 V |
| Gain-Bandwidth Product | 6.4 MHz |
| Input Common-Mode Behavior | Rail-to-rail input |
| Output Swing Behavior | Rail-to-rail output |
| Shutdown Support | Yes |
| Low-Power Classification | Low-power operational amplifier |
| Number of Circuits | 1 circuit |
| Package Type | 8-pin PDIP |
| 腳位數 | 8 pins |
| 安裝方式 | Through-hole |
| Product Classification | General-purpose amplifier |
TLV2460CP 8-pin pdip 腳位配置指南
TLV2460CP(8-pin pdip 封裝)的腳位配置。 此類比元件具有輸入、輸出與電源腳位。偏移歸零、補償與致能腳位配置請參閱製造商資料表。適用於訊號調理與放大器電路。
無詳細腳位定義資料: TLV2460CP.
請參閱 資料表 以查看完整腳位配置。
典型應用
TLV2460CP 適用於 6 應用s: Portable Sensor Signal Conditioning, Low-Voltage Instrumentation Buffering, Battery-Powered Monitoring System, Active Filter and Frequency Response Circuit, Audio and Communication Interface, Test and Measurement Front End.
Portable Sensor Signal Conditioning
The TLV2460CP is suitable for conditioning low-voltage sensor signals in portable measurement equipment because its rail-to-rail input and output behavior reduces signal loss near the supply rails. With a 6.4 MHz gain-bandwidth product, the amplifier can support higher-bandwidth sensing paths than a low-frequency general-purpose device while remaining classified as low-power. The shutdown pin can disable the amplifier between acquisition intervals, reducing system activity when measurements are not continuously required. Place the signal source close to the amplifier input, maintain short feedback paths, and verify the complete common-mode range for the selected supply voltage. The 8-pin PDIP package also simplifies probing and rework in prototype instrumentation.
推薦
Low-Voltage Instrumentation Buffering
The TLV2460CP can buffer sensor, transducer, or divider outputs in low-voltage instrumentation where the signal needs to drive a following measurement stage. Rail-to-rail input operation preserves available dynamic range, while rail-to-rail output maximizes swing into the next amplifier or converter stage. Its 6.4 MHz gain-bandwidth product gives the design more closed-loop bandwidth potential than a unity-gain-stable low-frequency op amp. The single-amplifier configuration also permits a dedicated signal channel where noise and layout isolation matter. Designers should check output loading, input bias-current error, noise gain, and stability with the specific feedback network before release, particularly when driving capacitive inputs or long routed signals.
推薦
Battery-Powered Monitoring System
The TLV2460CP fits battery-powered monitoring systems that require rail-to-rail signal operation and controlled amplifier activity. Its low-power design is complemented by a shutdown function, allowing the amplifier to be disabled when the system is idle and enabled for measurement or alarm evaluation. Rail-to-rail input and output characteristics are useful because low-voltage battery systems often operate signals close to their available supply range. The 6 V maximum supply rating permits use in sub-6 V systems, although the actual minimum and maximum operating voltages must be confirmed. A practical implementation should account for shutdown timing, input transients during wake-up, and the quiescent-current contribution of the complete analog signal chain.
推薦
Active Filter and Frequency Response Circuit
The TLV2460CP can serve as the active element in a low-voltage filter or frequency-response circuit because its 6.4 MHz gain-bandwidth product provides substantial bandwidth for signal shaping. Rail-to-rail operation helps preserve signal range in compact systems, and shutdown can disable the active path when filtering is unnecessary. The actual usable bandwidth depends on the closed-loop topology, noise gain, component tolerances, and the stability recommendations in the manufacturer datasheet. Use short PCB traces around the feedback network, keep sensitive input nodes away from switching nodes, and include suitable input and output bypassing. Prototype the frequency response across the intended load because capacitive loading can alter stability and attenuation.
推薦
Audio and Communication Interface
The TLV2460CP can amplify low-level signals in portable audio or communication interfaces where rail-to-rail operation is valuable. Its 6.4 MHz gain-bandwidth product is suitable for signal paths extending well beyond baseband audio frequencies, while the shutdown pin can control amplifier state in intermittently active systems. The through-hole PDIP package is convenient for bench prototypes and educational equipment where component accessibility and straightforward rework are important. Confirm input and output swing at the intended load, check distortion and output-current capability, and ensure the selected gain and feedback network remain stable. A ground-return path directly under the device should be used to reduce noise pickup and maintain predictable analog performance.
推薦
Test and Measurement Front End
The TLV2460CP is applicable to the input front end of low-voltage test and measurement equipment where a general-purpose rail-to-rail amplifier is needed. The single amplifier can condition a probe, attenuator, or diagnostic signal before conversion or comparison, while the 6.4 MHz gain-bandwidth product supports higher-frequency measurements than a slow precision amplifier. Rail-to-rail input and output operation helps use the available signal range, and shutdown is useful in repeated or gated measurement architectures. Designers should establish probe capacitance, source impedance, noise gain, and settling requirements before selecting compensation values. Keep the input path short, use a quiet ground reference, and verify that shutdown transitions do not create unacceptable settling time for the test sequence.
推薦
推薦產品摘要
工程參考資料,適用於 TLV2460CP — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | TLV2460CPE4 | TLV2460IPE4 | TLV2460IP |
|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | 8-pin PDIP | 8-pin PDIP | 8-pin PDIP | 8-pin PDIP |
| Amplifier Type | Single operational amplifier | Single operational amplifier | Single operational amplifier | Single operational amplifier |
主要差異化特點
- Confirmed single-amplifier RRIO configuration (對比TLV2460CPE4)
- Shutdown-capable low-voltage signal conditioning (對比TLV2460IPE4)
- Through-hole package supports accessible prototyping (對比TLV2460AIDR)
設計說明
Route input, feedback, output, and shutdown connections as short as practical, especially when the closed-loop gain is high. Place the input and output bypass capacitors at their corresponding supply pins rather than at a distant common capacitor. For the 8-pin PDIP, use a ground plane beneath the device and minimize copper-trace resistance between the amplifier and its bypass network. This is particularly important for rail-to-rail designs because supply and ground paths carry signal currents.
Treat the amplifier input as a high-impedance, high-gain node: avoid long parallel traces, test pads, and nearby switching signals unless their effects have been evaluated. If driving a cable, ADC input, or other capacitive load, confirm stability using the manufacturer recommendations and the actual load capacitance. The 6.4 MHz gain-bandwidth product provides response capability, but stable closed-loop operation still depends on noise gain and output loading.
Verify the shutdown-control polarity and state timing in the manufacturer datasheet before connecting it to a system enable signal. A floating or incorrectly driven shutdown node could leave the amplifier enabled or prevent normal operation. During startup, allow the analog supply to stabilize before sampling the output, and determine whether the sensor or source impedance can inject a transient during wake-up. The complete analog chain should be evaluated for quiescent-current and active-current impact.
Do not select a replacement solely from the 6.4 MHz bandwidth or 6 V supply rating. Compare the complete pin description, shutdown polarity, input common-mode range, output swing, offset voltage, bias current, noise, slew rate, output-current capability, operating-temperature range, and package-specific recommendations. When changing from TLV2460CP to another family ordering code, preserve the PCB footprint and verify that the revised grade covers the required environmental conditions.
合規資訊
Compliance attributes were not stated in the manufacturer or distributor page excerpts. The 8-pin PDIP package is leaded in construction, but lead-free and halogen-free status require confirmation from the manufacturer ordering information.