TLV2472CD - Dual 6V 2.8MHz RRIO Op Amp | Texas Instruments
MPN: TLV2472CD ✓ 啟用中TLV2472CD 概覽
A rail-to-rail operational amplifier is an amplifier whose input common-mode range and output swing can extend toward the positive and negative supply rails. The TLV2472 belongs to the CMOS operational-amplifier hierarchy within the broader analog and semiconductor categories. Its rail-to-rail input stage accepts signals near the supply limits, while the rail-to-rail output stage increases dynamic range in low-voltage systems where conventional amplifier outputs cannot approach the rails.
The TLV2472CD's principal features include a 2.8 MHz gain-bandwidth product, 1.4 V/µs slew rate, 600 µA supply current per channel, and low 2.5 pA input bias current. According to the Texas Instruments TLV2472 family documentation, the amplifier provides 78 dB common-mode rejection and operates across a supply range suitable for low-voltage, battery-powered systems. These characteristics balance signal fidelity against the power budget better than a high-bandwidth amplifier operating continuously at substantially higher quiescent current.
The two amplifiers share a common supply arrangement but can operate independently for filtering, amplification, buffering, or level conversion. Rail-to-rail input capability is especially useful when sensing sensor outputs close to ground or near a positive rail. Rail-to-rail output behavior helps preserve signal amplitude in portable instrumentation, while the 2.8 MHz gain-bandwidth product supports moderate-frequency closed-loop amplifiers and active filters. Exact offset, output-current, and supply-current limits should be confirmed against the manufacturer datasheet for the selected operating conditions.
Typical applications include low-power sensor interfaces, battery-operated instrumentation, audio signal conditioning, active analog filters, transducer amplification, and low-voltage data acquisition. The 8-pin SOIC footprint is also convenient for industrial control, portable medical equipment, and consumer accessories where two independent amplifier channels reduce component count. Design effort should focus on input common-mode limits, output swing, capacitive-load stability, noise bandwidth, and the power consumed by both channels.
For battery-powered operation, calculate total supply consumption from both channels and account for output-current demand across the expected signal range. Place decoupling capacitors close to the supply pins, use short feedback paths, and verify stability with the source and load impedances used in the finished board. The SOIC package also requires adequate copper area and thermal planning when either channel drives a load near the device's output-current limit.
This product record combines the manufacturer's device specifications, package and ordering information, commercial availability details, same-family replacement analysis, and practical circuit-design guidance. It also distinguishes verified TLV2472-family options from broader amplifier types, helping engineers evaluate drop-in compatibility, power consumption, noise, temperature range, and application fit before finalizing a PCB design.
直接替換替代品,適用於 TLV2472CD — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
TLV2472ID
✅ 直接替換📋 參考替代品(不在目錄中)
TLV2472CD 最大額定值與電氣特性
| Amplifier Type | Dual CMOS operational amplifier |
| Number of Channels | 2 channels |
| Maximum Supply Voltage | 6 V |
| Gain-Bandwidth Product | 2.8 MHz |
| Slew Rate | 1.4 V/µs |
| Supply Current per Channel | 600 µA |
| Input Bias Current | 2.5 pA |
| Input Voltage Noise Density | 15 nV/√Hz |
| Common-Mode Rejection Ratio | 78 dB |
| Input Common-Mode Range | Rail-to-rail |
| Output Swing | Rail-to-rail |
| Minimum Operating Temperature | -40 °C |
| Maximum Operating Temperature | +125 °C |
| 封裝 | 8-pin SOIC (D) |
| 安裝類型 | Surface-mount |
TLV2472CD 腳位配置
| 腳位 1 | OUTA — Output of amplifier A |
| 腳位 2 | IN A- — Inverting input of amplifier A |
| 腳位 3 | IN A+ — Non-inverting input of amplifier A |
| 腳位 4 | V+ — Positive supply connection |
| 腳位 5 | IN B+ — Non-inverting input of amplifier B |
| 腳位 6 | IN B- — Inverting input of amplifier B |
| 腳位 7 | OUTB — Output of amplifier B |
| 腳位 8 | V- — Negative supply connection, or ground in a single-supply circuit |
典型應用
TLV2472CD 適用於 6 應用s: Battery-Powered Sensor Conditioning, Low-Noise Instrumentation Amplification, Active Analog Filtering, Audio and Microphone Preamplification, Portable Data Acquisition, Industrial Control and Transducer Interfaces.
Battery-Powered Sensor Conditioning
The TLV2472CD suits battery-powered sensor interfaces because each channel consumes approximately 600 µA while providing a 2.8 MHz gain-bandwidth product and 2.5 pA input bias current. Place the dual amplifier around a high-impedance sensor stage to amplify a small bipolar or unipolar signal without bias-current error dominating the measurement. Rail-to-rail input operation is useful when the sensor output approaches either supply rail, and rail-to-rail output preserves more of the conditioned signal swing in a compact, low-voltage system.
推薦
Low-Noise Instrumentation Amplification
The TLV2472CD is appropriate for low-level instrumentation stages requiring 15 nV/√Hz input-voltage noise density and 78 dB common-mode rejection. Its dual architecture can implement a differential or noninverting conditioning stage, followed by filtering and output buffering within the same 8-pin SOIC. The 2.8 MHz gain-bandwidth product supports moderate-bandwidth closed-loop gains, while the 600 µA per-channel supply current limits power consumption in portable measurement equipment. Input and output headroom must still be checked across the complete signal range.
推薦
Active Analog Filtering
Both TLV2472CD channels can implement active low-pass, high-pass, or band-pass sections where a 2.8 MHz gain-bandwidth product and approximately 600 µA per channel are useful. The operational amplifier's rail-to-rail input and output characteristics support filters operating near low supply voltages, and the SOIC package allows the two sections to be placed close together. Select resistor and capacitor values against the desired gain and bandwidth, then verify closed-loop stability, capacitor tolerances, and output swing in the manufacturer datasheet.
推薦
Audio and Microphone Preamplification
The TLV2472CD can provide two channels of low-level audio or microphone amplification when low supply current is more important than wideband frequency response. Its rail-to-rail input stage accepts microphone-bias and source signals across nearly the full supply range, while 15 nV/√Hz noise density supports low-level acoustic measurements. The 1.4 V/µs slew rate allows small-signal waveform reproduction within the useful bandwidth. Confirm input capacitance, output drive, and the required gain-bandwidth relationship for the microphone impedance and line level.
推薦
Portable Data Acquisition
The TLV2472CD supports compact data-acquisition front ends that need two independently configurable analog channels without a high-power amplifier. A typical arrangement uses one channel for signal conditioning and the other for buffering or an additional conversion input. The 600 µA per-channel current helps preserve battery life, while 2.8 MHz bandwidth accommodates sensors and control signals beyond the audio range. Rail-to-rail operation reduces lost signal range in low-voltage systems, and the 8-pin SOIC simplifies assembly compared with separate single-channel packages.
推薦
Industrial Control and Transducer Interfaces
The TLV2472CD can amplify and filter control-board sensor signals where the 2.8 MHz gain-bandwidth product is adequate for moderate-bandwidth feedback and data conversion. Its dual-channel configuration reduces the number of packages needed for input conditioning and auxiliary buffering, while low input bias current limits loading on high-impedance transducers. Because the CD grade is rated from 0 °C to +70 °C, industrial equipment with wider internal temperature variation should evaluate TLV2472ID or another explicitly temperature-rated device before production release.
推薦
推薦產品摘要
工程參考資料,適用於 TLV2472CD — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | TLV2472ID |
|---|---|---|
| Package | 8-pin SOIC (D) | 8-pin SOIC (D) |
| Brand | Texas Instruments | Texas Instruments |
| Amplifier Configuration | Dual operational amplifier | Dual operational amplifier |
| Maximum Supply Voltage | 6 V | 6 V |
| Gain-Bandwidth Product | 2.8 MHz | 2.8 MHz |
| Slew Rate | 1.4 V/µs | 1.4 V/µs |
| Supply Current per Channel | 600 µA | 600 µA |
| Input Voltage Noise Density | 15 nV/√Hz | 15 nV/√Hz |
| Operating Temperature | 0 °C to +70 °C | -40 °C to +125 °C |
| Input and Output Common Mode | Rail-to-rail input and output | Rail-to-rail input and output |
主要差異化特點
- Low-power dual-channel architecture (對比TLV2472ID)
- Rail-to-rail signal range (對比TLV2472ID)
- Commercial-temperature operating range (對比TLV2472ID)
設計說明
Estimated: at the stated typical supply current of 600 µA per channel, two channels drawing from a 5 V rail dissipate approximately 5 V × 1.2 mA = 6 mW under no-load conditions. Actual consumption rises with output current and operating frequency. Use the lower operating voltage permitted by the complete signal chain, disable unused channels where supported by the system design, and confirm the final dissipation using the manufacturer's maximum-current electrical characteristics.
Place the supply-bypass capacitor immediately adjacent to the positive and negative supply pins, with a short, low-impedance connection to the ground plane. Route the two channels separately when one handles a sensitive input and the other drives a capacitive or high-current load. Keep feedback resistors close to their associated input and output pins, and maintain continuous ground-plane area beneath the SOIC to reduce loop area and susceptibility to coupled noise.
Do not select the TLV2472CD solely from the 2.8 MHz gain-bandwidth figure. The usable closed-loop bandwidth also depends on noise gain, feedback topology, load capacitance, output-current demand, and input common-mode position. Check the output-swing limits against the required signal, verify capacitive-load stability with the actual source and load impedances, and use the TLV2472ID temperature grade when the enclosure may exceed the CD part's 0 °C to +70 °C range.
For a 1% feedback resistor and an amplifier gain-bandwidth product of 2.8 MHz, the approximate small-signal closed-loop bandwidth is 2.8 MHz divided by the noise gain. This estimate does not include slew-rate limitation, load effects, or the exact gain-bandwidth curve. Use the manufacturer's AC characteristic plots to confirm attenuation and phase margin, and preserve ground-return paths around both input channels to minimize common-mode pickup.
合規資訊
The component is identified by Texas Instruments as the TLV2472CD in an 8-pin SOIC (D) package. Explicit RoHS, REACH, AEC-Q100, lead-free, halogen-free, and conflict-minerals statements were not present in the cited product information.