TLV2473CD - Dual 2.8MHz RRIO Op Amp | Texas Instruments
MPN: TLV2473CD ✓ 啟用中TLV2473CD 概覽
An operational amplifier is an amplifier IC that uses negative feedback to control gain and accurately amplify small input signals. The TLV2473 belongs to the CMOS operational-amplifier hierarchy, which includes rail-to-rail input/output amplifiers, low-power amplifiers, and general-purpose precision amplifiers. Rail-to-rail input operation supports signals near the supply rails, while rail-to-rail output capability allows the output to approach either rail under suitable load conditions.
The family provides rail-to-rail input and output stages, a 2.8 MHz gain-bandwidth product, approximately 600 uA of supply current per channel, and a shutdown function for reducing power consumption when the amplifier is not needed. These characteristics support applications where a conventional amplifier would consume excessive power or lack useful bandwidth for filtering and signal-conditioning tasks. The dual configuration also reduces board area by integrating two amplifier channels in one package.
The CMOS architecture targets a favorable combination of low power and moderate dynamic performance. A 2.8 MHz gain-bandwidth product is suitable for low-frequency active filters, sensor conditioning, audio preamplification, and general signal amplification. The approximately 600 uA-per-channel supply current helps reduce total system power in battery-operated or multi-channel equipment. Designers must still verify output swing, input range, noise, settling behavior, and shutdown logic against the operating conditions of their specific circuit.
Typical uses include industrial sensor interfaces, portable measurement instruments, low-frequency filter stages, audio signal chains, power-sequencing control, and general-purpose analog buffers. The shutdown pin can disable the amplifiers to reduce power use when a subsystem is inactive. Because both channels share the same device supply and shutdown control, applications requiring independently controlled channels may need separate devices.
For PCB design, place input, output, supply, and bypass connections close to their corresponding pins. Use a short ground return and decouple the supply near the package to reduce supply-noise coupling into the signal path. The common-mode input range, output load capability, and stability requirements should be checked directly in the manufacturer datasheet for the selected supply voltage and gain configuration.
This product page combines the manufacturer’s device description, ordering information, package details, and technical guidance with practical application, comparison, and design information. It helps engineers distinguish the TLV2473CD from nearby dual RRIO amplifier options while emphasizing shutdown capability, 2.8 MHz bandwidth, low supply current, and the 14-pin SOIC footprint.
直接替換替代品,適用於 TLV2473CD — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
TLV2473AIDR
✅ 直接替換📋 參考替代品(不在目錄中)
TLV2473IDR
✅ 直接替換📋 參考替代品(不在目錄中)
TLV2473ID
✅ 直接替換 ⚠️ 規格未經驗證📋 參考替代品(不在目錄中)
TLV2472IDR
✅ 直接替換 ⚠️ 規格未經驗證📋 參考替代品(不在目錄中)
TLV2471IDR
✅ 直接替換 ⚠️ 規格未經驗證📋 參考替代品(不在目錄中)
TLV2473CD 最大額定值與電氣特性
| Number of Amplifier Channels | 2 channels |
| Supply Voltage Range | 2.8 V to 6 V |
| Gain-Bandwidth Product | 2.8 MHz |
| Supply Current per Channel | Approximately 600 uA |
| Slew Rate | 1.5 V/us |
| Shutdown Function | Yes |
| 工作溫度範圍 | 0 C to +70 C |
| 封裝 | 14-pin SOIC (D) |
| 安裝類型 | Surface mount |
TLV2473CD 腳位配置
| 腳位 1 | OUTA — Amplifier A output |
| 腳位 2 | IN A- — Inverting input for amplifier A |
| 腳位 3 | IN A+ — Noninverting input for amplifier A |
| 腳位 4 | V- — Negative supply connection |
| 腳位 5 | SHUTDOWN — Shutdown control |
| 腳位 6 | IN B+ — Noninverting input for amplifier B |
| 腳位 7 | IN B- — Inverting input for amplifier B |
| 腳位 8 | OUTB — Amplifier B output |
| 腳位 9 | V+ — Positive supply connection |
| 腳位 10 | NC — Not connected |
| 腳位 11 | NC — Not connected |
| 腳位 12 | NC — Not connected |
| 腳位 13 | NC — Not connected |
| 腳位 14 | NC — Not connected |
典型應用
TLV2473CD 適用於 6 應用s: Industrial Sensor Signal Conditioning, Portable Measurement Instrumentation, Low-Frequency Active Filtering, Audio Preamplification, Power-Sequenced Analog Control, General-Purpose Analog Buffering.
Industrial Sensor Signal Conditioning
The TLV2473CD suits low-power sensor-conditioning stages that require amplification close to the source. Its dual 2.8 MHz channels can form cascaded gain stages or independent channels for a sensor and a reference signal, while approximately 600 uA of supply current per channel limits the power burden. Rail-to-rail input operation is useful when sensor outputs approach the supply rails. Designers must still check input bias current, offset voltage, common-mode limits, and output drive against the sensor impedance and operating temperature.
推薦
Portable Measurement Instrumentation
The TLV2473CD fits battery-powered instruments where amplifier power can materially affect operating time. The dual amplifier shares one 14-pin SOIC package, while its approximately 600 uA-per-channel supply current supports low-energy acquisition paths. A 2.8 MHz gain-bandwidth product is ample for many sensor, buffer, and active-filter stages operating below hundreds of kilohertz. The shutdown function is especially useful during idle measurement intervals, although its electrical timing should be confirmed before sequencing sensitive loads.
推薦
Low-Frequency Active Filtering
The TLV2473CD can implement low-frequency active filters using either channel independently. Its 2.8 MHz gain-bandwidth product provides more than enough loop bandwidth for many audio-band, control, or sensor-filter applications, and the 1.5 V/us slew rate helps preserve large-signal behavior. The dual arrangement allows a two-pole or higher-order filter in one package. Component tolerances, noise, output loading, and stability must be evaluated for the selected topology and closed-loop gain.
推薦
Audio Preamplification
The TLV2473CD is suitable for line-level audio preamplification when the design operates within the amplifier’s bandwidth and output-drive limits. Rail-to-rail input and output stages support signals near the supply rails, while the 2.8 MHz gain-bandwidth product comfortably covers conventional audio-band amplification. The dual package can handle two channels for stereo or provide gain and buffering stages in a mono circuit. Headroom, slew rate, distortion, noise, and shutdown behavior should be checked at the intended signal level and load.
推薦
Power-Sequenced Analog Control
The TLV2473CD shutdown function allows an analog subsystem to be disabled when it is not required, helping reduce current consumption in mixed-signal systems. Its dual channels can control or buffer two related analog nodes, provided both channels are intended to share the same shutdown state. The 2.8 V to 6 V supply range permits use in several low-voltage systems. Firmware and hardware sequencing should account for shutdown thresholds, startup timing, and the time required for outputs to become valid.
推薦
General-Purpose Analog Buffering
The TLV2473CD can buffer high-impedance sources or drive downstream circuitry when a unity-gain buffer provides useful isolation. Its 2.8 MHz bandwidth supports moderate-frequency signals, and the dual configuration provides two independent buffer paths in one package. Rail-to-rail operation is advantageous in compact systems where the signal can occupy much of the available supply range. Before loading the output, verify capacitive-drive limits, output-current capability, settling time, and stability with the chosen feedback network.
推薦
推薦產品摘要
工程參考資料,適用於 TLV2473CD — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | TLV2473AIDR | TLV2473IDR | TLV2473ID | TLV2472IDR | TLV2471IDR |
|---|---|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | 14-pin SOIC (D) | 14-pin SOIC (D) | 14-pin SOIC (D) | 14-pin SOIC (D) | 14-pin SOIC (D) | 14-pin SOIC (D) |
| Number of Channels | 2 | 2 | 2 | 2 | 2 | 2 |
主要差異化特點
- Closest web-identified direct replacement (對比TLV2473AIDR)
- Provides dual-channel integration in a compact SOIC (對比OPA828ID)
- Higher nominal bandwidth than lower-bandwidth family alternatives (對比TLV2472IDR)
設計說明
Place a supply bypass capacitor immediately beside the V+ and V- pins and connect it to a low-impedance ground plane. Because the TLV2473CD consumes approximately 600 uA per channel, supply noise and ground bounce can become significant relative to the signal being amplified. Use short, symmetric routing and avoid routing output currents through the input-reference ground path.
Keep the two input networks, feedback components, and output traces as compact as practical. Place input and feedback resistors close to the corresponding input pins to minimize parasitic capacitance and susceptibility to interference. Do not place long signal traces between the amplifier pins and their associated passive components, particularly around high-impedance sources where input bias current can create measurable voltage error.
Confirm output stability and drive capability for the intended load, including cable capacitance, sensor capacitance, and the input capacitance of the following stage. The 2.8 MHz gain-bandwidth product is suitable for many moderate-frequency applications, but closed-loop gain and load can affect usable bandwidth. Add an isolation resistor near the output when driving difficult capacitive loads and verify the resulting response on hardware.
Do not assume the shutdown control can tolerate arbitrary logic levels or that both channels can be disabled independently. Review the manufacturer pin description and timing characteristics, then define a startup sequence that keeps downstream nodes in a defined state. Also account for the 0 C to +70 C ordering range of the TLV2473CD when planning industrial or outdoor equipment.
合規資訊
The product page and ordering information identify the device and package, but no explicit environmental or material-compliance declarations are present in the cited records. The standard commercial 0 C to +70 C TLV2473CD option is not presented as an automotive-qualified device.