TLV2785ID - Quad 8MHz RRIO Op Amp with Shutdown | TI
MPN: TLV2785ID ✓ 啟用中TLV2785ID 概覽
An operational amplifier is a voltage-gain component used to amplify small input signals while buffering sources from subsequent circuit stages. The TLV2785 belongs to the rail-to-rail operational-amplifier family and operates as a general-purpose amplifier within the broader semiconductor and analog-signal-processing hierarchy. Rail-to-rail input capability permits operation near the supply rails, while rail-to-rail output capability increases usable output voltage range in low-voltage systems.
The principal features of the TLV2785ID include a 3.6 V maximum supply, 8 MHz gain-bandwidth, rail-to-rail input and output, and shutdown capability. Its low-voltage operation is suitable for systems powered from 1.8 V, 2.5 V, 3.0 V, or 3.3 V rails. A maximum input offset voltage of 4.5 mV and input bias current of 0.3 nA support applications where moderate DC precision and very low input leakage are useful.
The common-mode rejection ratio is specified at 80 dB, helping reject equal-magnitude signals appearing at both inputs. This characteristic is relevant to sensor interfaces and differential measurements where common-mode noise originates from power supplies, adjacent digital circuits, or long cable connections. The 8 MHz bandwidth also makes the amplifier useful for higher-frequency analog filtering, waveform conditioning, and low-level signal conversion.
Typical applications include portable measurement systems, industrial sensor conditioning, battery-powered instrumentation, communications equipment, and analog-to-digital converter input stages. The shutdown function can reduce supply current when the analog section is not required, although system design must ensure that shutdown sequencing does not disturb active downstream circuits.
When designing around the TLV2785ID, preserve the input common-mode range and output-swing limits under the actual supply voltage and load. Place the bypass capacitor close to the supply pins, route sensitive input traces away from switching nodes, and use short ground returns to preserve the device's low-noise and high-speed performance.
This product page combines the manufacturer specifications, package details, practical design guidance, comparison information, and traceable replacement options for engineers evaluating the TLV2785ID in compact 16-pin SOIC analog circuits.
直接替換替代品,適用於 TLV2785ID — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
TLV2785AID
✅ 直接替換📋 參考替代品(不在目錄中)
TLV2785ID 最大額定值與電氣特性
| Amplifier Count | 4 circuits |
| Product Type | Operational amplifier |
| Maximum Supply Voltage | 3.6 V |
| Minimum Single-Supply Voltage | 1.8 V |
| Single-Supply Voltage Range | 1.8 V to 3.6 V |
| Dual-Supply Voltage Range | +/-0.9 V to +/-1.8 V |
| Gain-Bandwidth Product | 8 MHz |
| Input Common-Mode Range | Rail-to-rail |
| Output Swing | Rail-to-rail |
| Maximum Input Offset Voltage | 4.5 mV |
| Input Bias Current | 0.3 nA |
| Common-Mode Rejection Ratio | 80 dB |
| Shutdown Control | Yes |
| 工作溫度範圍 | -40°C to +125°C |
| 封裝 | 16-pin SOIC, SO-16 |
| 安裝類型 | Surface mount |
TLV2785ID 腳位配置
| 腳位 1 | OUTA — Amplifier A output |
| 腳位 2 | IN-A — Amplifier A inverting input |
| 腳位 3 | IN+A — Amplifier A noninverting input |
| 腳位 4 | V+ — Positive supply voltage |
| 腳位 5 | IN+B — Amplifier B noninverting input |
| 腳位 6 | IN-B — Amplifier B inverting input |
| 腳位 7 | OUTB — Amplifier B output |
| 腳位 8 | OUTC — Amplifier C output |
| 腳位 9 | IN-C — Amplifier C inverting input |
| 腳位 10 | IN+C — Amplifier C noninverting input |
| 腳位 11 | V- — Negative supply voltage |
| 腳位 12 | IN+D — Amplifier D noninverting input |
| 腳位 13 | IN-D — Amplifier D inverting input |
| 腳位 14 | OUTD — Amplifier D output |
| 腳位 15 | SHDN — Shutdown control |
| 腳位 16 | V+ — Positive supply voltage |
典型應用
TLV2785ID 適用於 6 應用s: Portable Sensor Signal Conditioning, Industrial Data Acquisition, Low-Voltage ADC Input Driver, Battery-Powered Monitoring, Communications Interface Circuitry, Active Filtering and Waveform Conditioning.
Portable Sensor Signal Conditioning
The TLV2785ID is well suited to conditioning outputs from low-voltage sensors in portable instruments because its four amplifiers support multiple channels in one 16-pin SOIC and its input bias current is only 0.3 nA. Operation from 1.8 V to 3.6 V permits direct use with low-power sensor systems, while rail-to-rail input and output preserve signal range near the supply limits. The 80 dB common-mode rejection helps suppress noise shared by both inputs. Designers should include the 4.5 mV maximum input offset voltage in the accuracy budget and provide local supply bypassing for stable low-voltage operation.
推薦
Industrial Data Acquisition
The TLV2785ID can condition several analog measurement channels in compact industrial data-acquisition equipment because it combines four operational amplifiers with an 8 MHz gain-bandwidth product in a 16-pin SOIC package. Rail-to-rail input and output operation supports low-voltage sensor ranges, and the 80 dB common-mode rejection ratio helps reduce disturbance coupled into sensor lines. The device operates from 1.8 V to 3.6 V for embedded systems with constrained power budgets. For reliable measurements, use short guarded input routes, solid grounding, and decoupling capacitors positioned close to the supply pins.
推薦
Low-Voltage ADC Input Driver
The TLV2785ID provides a practical multi-channel drive stage for low-voltage analog-to-digital converter inputs because rail-to-rail operation maximizes the usable signal range between 1.8 V and 3.6 V supplies. An 8 MHz gain-bandwidth product gives sufficient bandwidth for many moderate-rate acquisition paths, while the quad configuration reduces the number of amplifier packages required on the PCB. The 4.5 mV maximum offset voltage must be considered at the system level. Confirm the ADC settling requirements and use short, low-capacitance routes from each amplifier output to minimize conversion-dependent errors.
推薦
Battery-Powered Monitoring
The TLV2785ID is useful in battery-powered monitoring systems where low-voltage operation and channel density are priorities. Its 1.8 V minimum supply allows operation from low-energy rails, and four amplifier channels can handle sensing, filtering, and level conditioning within one 16-pin SOIC. Rail-to-rail output behavior increases usable signal swing at low supply voltages, while shutdown control can disable the analog section during inactive periods. Power-budget calculations should include both active and shutdown behavior, and sensor leakage should remain low enough for the 0.3 nA input bias current not to dominate the measurement.
推薦
Communications Interface Circuitry
The TLV2785ID can support low-level communications-interface circuitry in compact equipment because it combines 8 MHz bandwidth, rail-to-rail signal handling, and four amplifiers per package. The high bandwidth is useful for gain stages, active filters, and receive-path conditioning around low-voltage digital systems. Its 80 dB common-mode rejection helps reject supply-related and coupled common-mode noise in differential signaling arrangements. Board implementation remains important: isolate the amplifier from switching-node energy, use continuous ground planes, and verify output settling with the actual cable, connector, and downstream input load.
推薦
Active Filtering and Waveform Conditioning
The TLV2785ID is appropriate for active filters and waveform-conditioning stages requiring more bandwidth than precision-only amplifiers usually provide. Its 8 MHz gain-bandwidth product supports signal paths from sensors, transducers, and low-level waveform sources, while the quad arrangement permits multiple filter sections or conditioning channels in one 16-pin SOIC. Rail-to-rail input and output improve headroom at low supply voltages. Component tolerances and amplifier stability determine the achievable filter response, so prototype the selected topology and check phase margin with realistic source and load impedances.
推薦
推薦產品摘要
工程參考資料,適用於 TLV2785ID — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | TLV2785AID |
|---|---|---|
| Package | 16-pin SOIC, SO-16 | 16-pin SOIC, SO-16 - same package |
| Brand | Texas Instruments | Texas Instruments |
| Amplifier Count | 4 circuits | 4 circuits |
| Product Type | Operational amplifier with shutdown | Operational amplifier with shutdown |
| Minimum Supply Voltage | 1.8 V | 1.8 V |
| Maximum Supply Voltage | 3.6 V | 3.6 V |
| Gain-Bandwidth Product | 8 MHz | 8 MHz |
| Input Common-Mode Range | Rail-to-rail | Rail-to-rail |
| Output Swing | Rail-to-rail | Rail-to-rail |
| Shutdown Control | Yes | Yes |
主要差異化特點
- Combines four high-speed amplifiers with shutdown in one low-voltage package (對比TLV2785AID)
- Supports very low-voltage signal-chain designs (對比TLV2785AID)
- Low input loading and useful common-mode rejection (對比TLV2785AID)
設計說明
Place the supply bypass capacitor directly between the positive and negative supply pins of the SOIC, with a short, low-inductance connection to the ground plane. Keep amplifier input and output traces away from switching nodes and digital return currents. Because the TLV2785ID has an 8 MHz gain-bandwidth product, even short PCB traces can acquire parasitic capacitance; use compact routing and verify sensitive outputs for oscillation with the intended load.
Account for the 4.5 mV maximum input offset voltage when setting the resolution of low-level sensor measurements. A practical approach is to use the amplifier's common-mode rejection and low input bias current without overstating its DC accuracy, then include offset, noise, and reference error in the complete measurement budget. For very low-level signals, evaluate trim, calibration, or a more precise amplifier rather than relying on nominal balance alone.
The shutdown pin can reduce consumption when the analog channels are idle, but its voltage thresholds and timing should be checked against the control signals in the system. Avoid allowing the shutdown node to float, and ensure every amplifier output is placed in a defined state when shutdown is asserted. The normal operating supply range is 1.8 V to 3.6 V, so verify rail sequencing and do not exceed the 3.6 V maximum supply rating.
Do not treat another low-voltage quad amplifier as a drop-in part solely because it uses a 16-pin SOIC. Confirm pin names, shutdown polarity, supply limits, input common-mode range, output swing, gain-bandwidth, stability, and operating temperature. The TLV2785AID is the closest same-family option, while reel or tape-and-reel ordering codes do not add a distinct engineering alternative and should not be listed as separate replacements.
合規資訊
Complete compliance declarations are not stated in the available manufacturer and distributor product information. Confirm current RoHS, REACH, AEC-Q100, lead-free, halogen-free, and conflict-minerals status from Texas Instruments before production release.