Texas Instruments

TLV2785ID - Quad 8MHz RRIO Op Amp with Shutdown | TI

料号: TLV2785ID ✓ 量产中
3.6 V Vdss 0.3 nA Id 16-pin SOIC, SO-16 Package
最小起订量: 1 |

TLV2785ID 概述

Texas Instruments TLV2785ID is a quad operational amplifier designed for low-voltage, high-speed signal conditioning, with 8 MHz gain-bandwidth, rail-to-rail input and output operation, and a minimum 1.8 V supply in a 16-pin SOIC package. The four amplifiers include shutdown control, making the device suitable for portable instrumentation, sensor interfaces, data acquisition, and low-voltage industrial systems.

An operational amplifier is a voltage-gain component used to amplify small input signals while buffering sources from subsequent circuit stages. The TLV2785 belongs to the rail-to-rail operational-amplifier family and operates as a general-purpose amplifier within the broader semiconductor and analog-signal-processing hierarchy. Rail-to-rail input capability permits operation near the supply rails, while rail-to-rail output capability increases usable output voltage range in low-voltage systems.

The principal features of the TLV2785ID include a 3.6 V maximum supply, 8 MHz gain-bandwidth, rail-to-rail input and output, and shutdown capability. Its low-voltage operation is suitable for systems powered from 1.8 V, 2.5 V, 3.0 V, or 3.3 V rails. A maximum input offset voltage of 4.5 mV and input bias current of 0.3 nA support applications where moderate DC precision and very low input leakage are useful.

The common-mode rejection ratio is specified at 80 dB, helping reject equal-magnitude signals appearing at both inputs. This characteristic is relevant to sensor interfaces and differential measurements where common-mode noise originates from power supplies, adjacent digital circuits, or long cable connections. The 8 MHz bandwidth also makes the amplifier useful for higher-frequency analog filtering, waveform conditioning, and low-level signal conversion.

Typical applications include portable measurement systems, industrial sensor conditioning, battery-powered instrumentation, communications equipment, and analog-to-digital converter input stages. The shutdown function can reduce supply current when the analog section is not required, although system design must ensure that shutdown sequencing does not disturb active downstream circuits.

When designing around the TLV2785ID, preserve the input common-mode range and output-swing limits under the actual supply voltage and load. Place the bypass capacitor close to the supply pins, route sensitive input traces away from switching nodes, and use short ground returns to preserve the device's low-noise and high-speed performance.

This product page combines the manufacturer specifications, package details, practical design guidance, comparison information, and traceable replacement options for engineers evaluating the TLV2785ID in compact 16-pin SOIC analog circuits.

直接替换替代料: TLV2785ID ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。

TLV2785AID

✅ 直接替换
📦 16-pin SOIC, SO-16
Revised A-series family option; supply rating is 3.6 V and gain-bandwidth is 8 MHz, a 0% difference on those two documented ratings, while revision-specific DC limits require verification

📋 参考替代料(不在目录中)

TLV2785ID 最大额定值与电气特性

Amplifier Count 4 circuits
Product Type Operational amplifier
Maximum Supply Voltage 3.6 V
Minimum Single-Supply Voltage 1.8 V
Single-Supply Voltage Range 1.8 V to 3.6 V
Dual-Supply Voltage Range +/-0.9 V to +/-1.8 V
Gain-Bandwidth Product 8 MHz
Input Common-Mode Range Rail-to-rail
Output Swing Rail-to-rail
Maximum Input Offset Voltage 4.5 mV
Input Bias Current 0.3 nA
Common-Mode Rejection Ratio 80 dB
Shutdown Control Yes
工作温度范围 -40°C to +125°C
封装 16-pin SOIC, SO-16
安装类型 Surface mount

TLV2785ID 引脚配置

SOIC-16 Package Pinout Diagram SOIC-16 16-pin, 3.9x9.9mm, P1.27mm, JEDEC MS-012. 1 16 2 15 3 14 4 13 5 12 6 11 7 10 8 9 SOIC-16
引脚 1 OUTA — Amplifier A output
引脚 2 IN-A — Amplifier A inverting input
引脚 3 IN+A — Amplifier A noninverting input
引脚 4 V+ — Positive supply voltage
引脚 5 IN+B — Amplifier B noninverting input
引脚 6 IN-B — Amplifier B inverting input
引脚 7 OUTB — Amplifier B output
引脚 8 OUTC — Amplifier C output
引脚 9 IN-C — Amplifier C inverting input
引脚 10 IN+C — Amplifier C noninverting input
引脚 11 V- — Negative supply voltage
引脚 12 IN+D — Amplifier D noninverting input
引脚 13 IN-D — Amplifier D inverting input
引脚 14 OUTD — Amplifier D output
引脚 15 SHDN — Shutdown control
引脚 16 V+ — Positive supply voltage

典型应用

TLV2785ID 适用于 6 应用s: Portable Sensor Signal Conditioning, Industrial Data Acquisition, Low-Voltage ADC Input Driver, Battery-Powered Monitoring, Communications Interface Circuitry, Active Filtering and Waveform Conditioning.

📱

Portable Sensor Signal Conditioning

The TLV2785ID is well suited to conditioning outputs from low-voltage sensors in portable instruments because its four amplifiers support multiple channels in one 16-pin SOIC and its input bias current is only 0.3 nA. Operation from 1.8 V to 3.6 V permits direct use with low-power sensor systems, while rail-to-rail input and output preserve signal range near the supply limits. The 80 dB common-mode rejection helps suppress noise shared by both inputs. Designers should include the 4.5 mV maximum input offset voltage in the accuracy budget and provide local supply bypassing for stable low-voltage operation.

🏭

Industrial Data Acquisition

The TLV2785ID can condition several analog measurement channels in compact industrial data-acquisition equipment because it combines four operational amplifiers with an 8 MHz gain-bandwidth product in a 16-pin SOIC package. Rail-to-rail input and output operation supports low-voltage sensor ranges, and the 80 dB common-mode rejection ratio helps reduce disturbance coupled into sensor lines. The device operates from 1.8 V to 3.6 V for embedded systems with constrained power budgets. For reliable measurements, use short guarded input routes, solid grounding, and decoupling capacitors positioned close to the supply pins.

📊

Low-Voltage ADC Input Driver

The TLV2785ID provides a practical multi-channel drive stage for low-voltage analog-to-digital converter inputs because rail-to-rail operation maximizes the usable signal range between 1.8 V and 3.6 V supplies. An 8 MHz gain-bandwidth product gives sufficient bandwidth for many moderate-rate acquisition paths, while the quad configuration reduces the number of amplifier packages required on the PCB. The 4.5 mV maximum offset voltage must be considered at the system level. Confirm the ADC settling requirements and use short, low-capacitance routes from each amplifier output to minimize conversion-dependent errors.

🔋

Battery-Powered Monitoring

The TLV2785ID is useful in battery-powered monitoring systems where low-voltage operation and channel density are priorities. Its 1.8 V minimum supply allows operation from low-energy rails, and four amplifier channels can handle sensing, filtering, and level conditioning within one 16-pin SOIC. Rail-to-rail output behavior increases usable signal swing at low supply voltages, while shutdown control can disable the analog section during inactive periods. Power-budget calculations should include both active and shutdown behavior, and sensor leakage should remain low enough for the 0.3 nA input bias current not to dominate the measurement.

🌐

Communications Interface Circuitry

The TLV2785ID can support low-level communications-interface circuitry in compact equipment because it combines 8 MHz bandwidth, rail-to-rail signal handling, and four amplifiers per package. The high bandwidth is useful for gain stages, active filters, and receive-path conditioning around low-voltage digital systems. Its 80 dB common-mode rejection helps reject supply-related and coupled common-mode noise in differential signaling arrangements. Board implementation remains important: isolate the amplifier from switching-node energy, use continuous ground planes, and verify output settling with the actual cable, connector, and downstream input load.

〰️

Active Filtering and Waveform Conditioning

The TLV2785ID is appropriate for active filters and waveform-conditioning stages requiring more bandwidth than precision-only amplifiers usually provide. Its 8 MHz gain-bandwidth product supports signal paths from sensors, transducers, and low-level waveform sources, while the quad arrangement permits multiple filter sections or conditioning channels in one 16-pin SOIC. Rail-to-rail input and output improve headroom at low supply voltages. Component tolerances and amplifier stability determine the achievable filter response, so prototype the selected topology and check phase margin with realistic source and load impedances.

推荐产品汇总

TLV2785ID Texas Instruments 用于: Portable Sensor Signal Conditioning, Industrial Data Acquisition, Low-Voltage ADC Input Driver, Battery-Powered Monitoring, Communications Interface Circuitry, Active Filtering and Waveform Conditioning TLV2785AID Same-family revised quad amplifier option 用于: Portable Sensor Signal Conditioning, Industrial Data Acquisition, Low-Voltage ADC Input Driver, Battery-Powered Monitoring, Communications Interface Circuitry, Active Filtering and Waveform Conditioning
What is the TLV2785ID?
The TLV2785ID is a quad, 8 MHz operational amplifier with rail-to-rail input and output, shutdown control, and operation from 1.8 V to 3.6 V. According to the Texas Instruments manufacturer datasheet, it is intended for low-voltage, high-speed signal conditioning. The four amplifiers are integrated in a 16-pin SOIC package, allowing multiple analog channels to be placed in a compact footprint.
What are the key specifications of TLV2785ID that engineers should know?
The TLV2785ID combines four operational amplifiers, an 8 MHz gain-bandwidth product, rail-to-rail input and output, and shutdown control in one 16-pin SOIC. Its documented supply range is 1.8 V to 3.6 V, maximum input offset voltage is 4.5 mV, input bias current is 0.3 nA, and common-mode rejection is 80 dB. These characteristics make it relevant to low-voltage sensor, filtering, and data-conversion interfaces.
What is the operating voltage range of TLV2785ID?
The TLV2785ID operates from 1.8 V to 3.6 V on a single supply and from +/-0.9 V to +/-1.8 V on dual supplies. According to the Texas Instruments manufacturer datasheet, this low-voltage range supports 1.8 V, 2.5 V, 3.0 V, and 3.3 V systems. The output-swing and common-mode limits should still be checked against the actual supply voltage and load.
Where can I download the TLV2785ID datasheet PDF?
Download the TLV2785ID documentation from the Texas Instruments product page at https://www.ti.com/product/TLV2785 or use the manufacturer PDF link listed on this page. The document contains the electrical characteristics, pin configuration, typical performance curves, application information, and ordering information needed to evaluate the quad amplifier and its shutdown function.
Where can I find the TLV2785ID pinout?
The TLV2785ID pin configuration is shown in the pin-configuration section of the Texas Instruments manufacturer datasheet. The device uses a 16-pin SOIC with four amplifier channels, positive and negative supply pins, and a shutdown-control pin. Assign PCB nets from that table rather than inferring connections solely from amplifier-channel numbering.
Is the TLV2785ID suitable for low-voltage sensor interfaces?
Yes, the TLV2785ID is suitable for low-voltage sensor interfaces because it operates down to 1.8 V and supports rail-to-rail input and output. Its 80 dB common-mode rejection helps reduce common-mode disturbance, while the 0.3 nA input bias current limits loading from high-impedance sensors. Its 4.5 mV maximum input offset voltage should be included in the system error budget.
What can replace the TLV2785ID?
The TLV2785AID is a documented same-manufacturer candidate in the 16-pin SOIC family, but it represents a revised device rather than an exact ordering-code match. According to the Texas Instruments family information, both devices provide a quad, low-voltage, rail-to-rail amplifier with shutdown. Confirm the revised device's electrical limits, lifecycle status, and production configuration before treating it as a drop-in replacement.
Can TLV2785AID replace TLV2785ID without changing the PCB?
The TLV2785AID uses the same 16-pin SOIC configuration and belongs to the same TLV2785 amplifier family, making it the closest documented replacement candidate. Its core role remains a quad, 1.8 V-to-3.6 V, 8 MHz rail-to-rail amplifier with shutdown. Before substitution, verify revision-specific DC accuracy, limits, qualification, and availability against the current manufacturer datasheet.
TLV2785ID vs TLV2785AID: which is better for a new design?
Choose TLV2785AID for a new design only after comparing the current revision-specific specifications and qualification requirements. Both devices are quad, 8 MHz, rail-to-rail operational amplifiers with shutdown in a 16-pin SOIC. The TLV2785ID is the exact target ordering option, while TLV2785AID belongs to the revised family; the correct choice depends on required electrical limits and lifecycle needs.
When should I choose TLV2785ID over another low-voltage quad op amp?
Choose the TLV2785ID when a design requires four amplifiers, a 1.8 V minimum supply, an 8 MHz gain-bandwidth product, rail-to-rail input and output, and a shutdown pin in one 16-pin SOIC. It is especially useful when board area is constrained and multiple low-voltage channels must be handled. If a candidate lacks shutdown or uses a different package, it is not a direct footprint replacement.
What is the best operational-amplifier equivalent for TLV2785ID?
No cross-manufacturer equivalent can be identified as a confirmed drop-in replacement from the available documentation. The TLV2785AID is the closest same-manufacturer candidate because it retains the 16-pin SOIC, quad-channel, low-voltage, rail-to-rail, shutdown architecture. A competitor part should be considered only after its pinout, supply limits, bandwidth, offset, bias current, shutdown polarity, and stability characteristics have been verified.
Is TLV2785ID in stock and what is its lead time?
Use the Request a Quote form on this page for current stock, minimum-order quantity, lead time, and order confirmation. The TLV2785ID is identified as an active Texas Instruments product, but live inventory and delivery schedules can change by package, quantity, and supply conditions. The distributor listing confirms the part is offered for ordering but does not provide a stable stock quantity for quotation.
Where can I buy TLV2785ID online?
Request a quote for the TLV2785ID through the Request a Quote form on this page. The form allows procurement teams to confirm current availability, lead time, quantity breaks, and packaging requirements for the 16-pin SOIC device. The manufacturer part number is TLV2785ID, and the order code should be checked against the required temperature and packaging configuration before placement.
How much does TLV2785ID cost?
Current commercial terms for the TLV2785ID are available through the Request a Quote form on this page. The form can provide quantity-based pricing for production quantities and identify any minimum-order or packaging constraints. Pricing should be confirmed for the exact 16-pin SOIC ordering code because commercial terms can change with volume, availability, and market conditions.
What design considerations apply when using TLV2785ID at high speed?
Keep the bypass capacitor close to the supply pins, route input and output traces away from switching nodes, and maintain a low-impedance ground return. The 8 MHz gain-bandwidth provides substantial bandwidth, so small parasitic capacitances and long board traces can affect stability or channel-to-channel timing. Use short traces, clean grounding, and appropriate output-load isolation when driving capacitive loads.
Does TLV2785ID meet RoHS and REACH requirements?
Confirm the current compliance declarations from the manufacturer product page and the applicable regulatory material before releasing a production BOM. The available product information identifies the manufacturer, active family, electrical characteristics, and package, but it does not state the complete RoHS, REACH, lead-free, halogen-free, or conflict-minerals status. Use those manufacturer declarations for final compliance qualification.

工程参考数据: TLV2785ID ——对比、设计指导和合规信息。

选型指南

Choose the TLV2785ID when the design needs four rail-to-rail operational amplifiers, an 8 MHz gain-bandwidth product, shutdown control, and operation from 1.8 V to 3.6 V in a 16-pin SOIC. It is particularly effective for portable measurement, sensor conditioning, low-voltage ADC interfaces, and compact multi-channel analog systems. Select the TLV2785AID when its revised electrical characteristics provide a lifecycle or production advantage, but verify revision-specific offset and bias-current limits before substitution. Avoid candidates that merely use a quad SOIC package; they must also match pin assignments, shutdown polarity, common-mode range, output swing, bandwidth, and stability behavior. If an alternative lacks shutdown or requires a different footprint, it is not a direct replacement and would require PCB redesign.

与替代料对比

参数 本产品 TLV2785AID
Package 16-pin SOIC, SO-16 16-pin SOIC, SO-16 - same package
Brand Texas Instruments Texas Instruments
Amplifier Count 4 circuits 4 circuits
Product Type Operational amplifier with shutdown Operational amplifier with shutdown
Minimum Supply Voltage 1.8 V 1.8 V
Maximum Supply Voltage 3.6 V 3.6 V
Gain-Bandwidth Product 8 MHz 8 MHz
Input Common-Mode Range Rail-to-rail Rail-to-rail
Output Swing Rail-to-rail Rail-to-rail
Shutdown Control Yes Yes

关键差异点

  • Combines four high-speed amplifiers with shutdown in one low-voltage package (对比 TLV2785AID)
  • Supports very low-voltage signal-chain designs (对比 TLV2785AID)
  • Low input loading and useful common-mode rejection (对比 TLV2785AID)

设计说明

Place the supply bypass capacitor directly between the positive and negative supply pins of the SOIC, with a short, low-inductance connection to the ground plane. Keep amplifier input and output traces away from switching nodes and digital return currents. Because the TLV2785ID has an 8 MHz gain-bandwidth product, even short PCB traces can acquire parasitic capacitance; use compact routing and verify sensitive outputs for oscillation with the intended load.

Account for the 4.5 mV maximum input offset voltage when setting the resolution of low-level sensor measurements. A practical approach is to use the amplifier's common-mode rejection and low input bias current without overstating its DC accuracy, then include offset, noise, and reference error in the complete measurement budget. For very low-level signals, evaluate trim, calibration, or a more precise amplifier rather than relying on nominal balance alone.

The shutdown pin can reduce consumption when the analog channels are idle, but its voltage thresholds and timing should be checked against the control signals in the system. Avoid allowing the shutdown node to float, and ensure every amplifier output is placed in a defined state when shutdown is asserted. The normal operating supply range is 1.8 V to 3.6 V, so verify rail sequencing and do not exceed the 3.6 V maximum supply rating.

Do not treat another low-voltage quad amplifier as a drop-in part solely because it uses a 16-pin SOIC. Confirm pin names, shutdown polarity, supply limits, input common-mode range, output swing, gain-bandwidth, stability, and operating temperature. The TLV2785AID is the closest same-family option, while reel or tape-and-reel ordering codes do not add a distinct engineering alternative and should not be listed as separate replacements.

合规信息

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
无铅
Unknown
无卤
Unknown
冲突矿物
Unknown

Complete compliance declarations are not stated in the available manufacturer and distributor product information. Confirm current RoHS, REACH, AEC-Q100, lead-free, halogen-free, and conflict-minerals status from Texas Instruments before production release.

相关搜索

TLV2785ID TLV2785ID datasheet TLV2785ID datasheet pdf TLV2785ID pinout TLV2785ID specifications TLV2785ID equivalent TLV2785ID replacement TLV2785ID cross reference TLV2785ID vs TLV2785AID TLV2785ID price TLV2785ID stock Texas Instruments TLV2785ID TLV2785ID application circuit TLV2785ID SOIC-16 amplifier

相关元器件 & 术语

Texas Instruments TLV2785ID TLV2785AID TLV2785 quad operational amplifier operational amplifier analog amplifier amplifier IC low-dropout rail-to-rail input rail-to-rail output RRIO gain-bandwidth product GBW common-mode rejection ratio CMRR input offset voltage input bias current shutdown control 16-pin SOIC SO-16 surface-mount package low-voltage instrumentation sensor signal conditioning industrial data acquisition
快速报价
填写完整信息——我们的销售团队将在 24 小时内回复
料号 制造商 封装 QTY 目标价 小计
✓
报价已提交!

我们将在 24 小时内回复您的邮件

1
询价已提交
2
已收到报价
3
已下单
4
支付
5
已发货
6
已送达
查看询价详情