TS3022ID - Dual High-Speed Rail-to-Rail Comparator | STMicroelectronics
MPN: TS3022ID ✓ 啟用中TS3022ID 概覽
A comparator is an analog integrated circuit that compares two input voltages and changes its output state when one input becomes higher than the other. The TS3022 belongs to the comparator hierarchy within analog and mixed-signal semiconductors, where its low supply-voltage operation and rail-to-rail inputs help simplify designs operating from 2 V to 5 V rails. Rail-to-rail input behavior is especially useful when the signal range approaches either supply rail, while the high-speed response supports applications requiring rapid threshold decisions.
The TS3022ID is identified as a general-purpose dual comparator with push-pull outputs. Its specified supply range is 2 V to 5 V, and the datasheet describes a high-speed response time. The TS3022 family is designed for micropower operation, with supply consumption described as being as low as a few tens of microamperes. The operating temperature range of -40 °C to +125 °C supports use across industrial, automotive, and consumer temperature conditions when the surrounding system satisfies the device's electrical requirements.
The rail-to-rail input architecture allows sensing of signals close to the positive or negative supply rails. This can reduce the need for artificial input biasing in low-voltage systems, although input common-mode behavior, output timing, and supply decoupling still require careful validation in the final application. Because the device contains two comparators, applications can use the two channels for independent decisions or for upper and lower thresholds that define a monitoring window.
Typical uses include battery-voltage threshold detection, overvoltage and undervoltage indication, signal crossing detection, pulse-width qualification, sensor-level conditioning, and fast logic-level generation. The 8-SOIC package is also convenient for prototypes and through-hole assembly. For battery-powered equipment, the low operating voltage and micropower characteristics can help reduce system energy use, provided the input signals remain within the specified common-mode range.
Designers should place supply bypass capacitance close to the device and use the pin descriptions in the manufacturer datasheet when assigning PCB tracks. Input filtering may be required when noisy signals are compared because propagation delay and input offset can cause repeated output transitions. The TS3022ID is therefore most appropriate when a designer needs two fast, low-voltage, rail-to-rail comparator channels in a conventional SOIC footprint.
直接替換替代品,適用於 TS3022ID — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
TS3022IDT
✅ 直接替換📋 參考替代品(不在目錄中)
TS3022IST
✅ 直接替換📋 參考替代品(不在目錄中)
TS3022IYST
✅ 直接替換📋 參考替代品(不在目錄中)
TS3022ID 最大額定值與電氣特性
| Comparator Type | General-purpose dual comparator |
| Number of Channels | 2 channels |
| Supply Voltage Range | 2 V to 5 V |
| Input Type | Rail-to-rail input |
| 輸出類型 | Push-pull |
| 工作溫度範圍 | -40 °C to +125 °C |
| Input Offset Voltage | 10 mV maximum |
| Average Input Bias Current | 0.3 µA maximum |
| 靜態電流 | A few tens of µA |
| 封裝 | 8-SOIC |
| 安裝類型 | Surface mount |
| Lead-Free / Terminal Finish | Nickel-palladium-gold terminal finish |
TS3022ID 8-soic 腳位配置指南
TS3022ID(8-soic 封裝)的腳位配置。 此類比元件具有輸入、輸出與電源腳位。偏移歸零、補償與致能腳位配置請參閱製造商資料表。適用於訊號調理與放大器電路。
無詳細腳位定義資料: TS3022ID.
請參閱 資料表 以查看完整腳位配置。
典型應用
TS3022ID 適用於 6 應用s: Battery Voltage Monitoring, Overvoltage and Undervoltage Protection, Sensor Signal Conditioning, Fast Signal Crossing Detection, Pulse Width Qualification, Portable Device Level Detection.
Battery Voltage Monitoring
The TS3022ID is well suited to detecting upper and lower battery-voltage thresholds because its two comparator channels operate from a 2 V to 5 V supply and accept rail-to-rail inputs. One channel can monitor the battery against a high threshold while the other detects a low threshold, allowing a controller input to identify an overvoltage or undervoltage condition. The 8-SOIC package simplifies assembly in industrial and portable systems, while rail-to-rail sensing improves utilization of a low-voltage signal range. Hysteresis should be added around the switching thresholds to prevent repeated output transitions when the battery voltage slowly changes. The push-pull outputs can directly drive a digital input or logic gate when voltage-level compatibility is confirmed.
推薦
Overvoltage and Undervoltage Protection
The TS3022ID can implement independent overvoltage and undervoltage supervision with its two rail-to-rail comparator channels. The 2 V minimum supply supports low-energy systems, and the specified -40 °C to +125 °C range provides useful temperature coverage for industrial equipment. Each channel compares an adjusted input against a reference voltage and produces a push-pull logic result for downstream control. Input dividers should be calculated for the full monitored range, with resistor tolerance and input offset voltage included in the threshold error budget. Positive feedback can introduce controlled hysteresis and avoid chatter around the protection boundary. The dual-channel arrangement also reduces the number of separate comparator footprints compared with two discrete single-channel devices.
推薦
Sensor Signal Conditioning
The TS3022ID can convert a sensor or conditioned analog signal into a fast digital threshold event using its rail-to-rail input stage. It is useful when a sensor output crosses a known level and the system needs a clean logic indication rather than continuous analog measurement. The high-speed response supports rapid threshold crossing, while the push-pull output provides a strong driven state suitable for digital inputs or control logic. Place the sensor and comparator paths to minimize coupling from switching nodes, and add filtering only where the required response time permits. With two channels, the same device can monitor one sensor against an upper threshold and another against a lower threshold, reducing board area in compact sensing modules.
推薦
Fast Signal Crossing Detection
The TS3022ID is appropriate for detecting when an analog waveform crosses a threshold, because the family is specified for high-speed response and rail-to-rail input operation. A divided input can be compared with a stable reference, creating a binary transition at a defined crossing point. The push-pull output can then trigger capture logic, interrupt a controller, or inhibit a downstream stage. Keep the reference source low impedance and minimize parasitic capacitance on the input node to preserve edge timing. If noisy or slow-moving signals are compared, intentional hysteresis is necessary to prevent repeated transitions. The dual comparator package can handle two related crossings without requiring two separate IC footprints.
推薦
Pulse Width Qualification
Two TS3022ID channels can support pulse-width qualification by defining a lower crossing and an upper crossing and combining the resulting comparator states in external logic. The rail-to-rail inputs help detect signals that occupy much of the 2 V to 5 V supply range, while the high-speed response supports short events. The design must account for propagation delay and reference timing when pulses approach the qualification window, so validate timing over process, voltage, and temperature. Add hysteresis or use a small amount of controlled feedback to prevent retriggering near each threshold. The 8-SOIC package is convenient for timing and industrial control boards that already use through-hole-compatible assembly methods.
推薦
Portable Device Level Detection
The TS3022ID can supervise a portable device's internal rail or battery condition while consuming only a few tens of microamperes according to the manufacturer family description. Its 2 V minimum supply supports operation from low-energy rails, and the two channels can monitor separate system conditions without requiring two comparator packages. The rail-to-rail input range allows direct sensing near the supply limits when divider scaling is appropriate. For battery systems, output transitions should be interpreted cautiously during supply collapse because dynamic behavior near the lower operating limit can differ from steady-state specifications. A quote request can establish current availability for the exact ordering suffix and required delivery quantity.
推薦
推薦產品摘要
工程參考資料,適用於 TS3022ID — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | TS3022IDT | TS3022IST | TS3022IYST |
|---|---|---|---|---|
| Brand | STMicroelectronics | STMicroelectronics | STMicroelectronics | STMicroelectronics |
| Package | 8-SOIC | 8-SOIC | 8-SOIC | 8-SOIC |
| Comparator Configuration | Dual | Dual | Dual | Dual |
| Supply Voltage Range | 2 V to 5 V | 2 V to 5 V | 2 V to 5 V | 2 V to 5 V |
| Input Type | Rail-to-rail | Rail-to-rail | Rail-to-rail | Rail-to-rail |
| Output Type | Push-pull | Push-pull | Push-pull | Push-pull |
| Operating Temperature Range | -40 °C to +125 °C | -40 °C to +125 °C | -40 °C to +125 °C | -40 °C to +125 °C |
| Ordering Suffix | ID | IDT | IST | IYST |
主要差異化特點
- Two independent comparator channels in one package (對比TS3022IDT)
- Rail-to-rail input operation across a 2 V to 5 V supply (對比TS3022IST)
- Push-pull outputs with a -40 °C to +125 °C operating range (對比TS3022IYST)
設計說明
Route the two comparator inputs as short, guarded traces, especially when the compared signal crosses a threshold rapidly. Keep switching outputs away from reference and high-impedance input nodes to reduce coupling. Place the supply bypass capacitor close to the device's supply and ground pins, and use the pin-description table in the STMicroelectronics datasheet to confirm the 8-SOIC land pattern.
Do not assume that rail-to-rail inputs make every signal condition acceptable. Check common-mode limits across the complete 2 V to 5 V supply range, including startup and transient conditions, and account for the maximum input offset voltage of 10 mV when setting precision thresholds. Add positive-feedback hysteresis when the input can remain near the comparison point, otherwise output chatter may increase system power and propagate false events.
Use a low-impedance reference source and short input routes for fast crossing applications. Filter the input only when the added capacitance will not undermine the required response time. Validate propagation behavior at the lowest expected supply voltage and highest operating temperature, since threshold timing margins can vary across operating conditions even though the TS3022 family is characterized as high speed.
Estimate total power from the 2 V to 5 V supply and the comparator operating current rather than relying only on the few-tens-of-microamperes family description. Account for both channels, output-state current, input bias current, and external load current. Low-power designs should also define behavior during supply ramp-down, when rail-to-rail input and output states may no longer represent valid comparisons.
合規資訊
The cross-reference data identifies a nickel-palladium-gold terminal finish, but it does not explicitly establish RoHS, REACH, AEC-Q100, halogen-free, or conflict-minerals status for TS3022ID.