TS941AID - Rail-to-Rail Micropower Op Amp | STMicroelectronics
MPN: TS941AID ✓ 啟用中TS941AID 概覽
Operational amplifiers are analog signal-processing devices that amplify the difference between two input voltages. A rail-to-rail output amplifier can approach its positive and negative supply rails more closely than a conventional amplifier, which helps preserve signal amplitude in low-voltage applications. The micropower operating class of the TS941AID makes it suitable for battery-operated and portable equipment where supply current must remain controlled.
The TS941AID is a single amplifier in an 8-SOIC package, allowing designers to add analog conditioning without using a higher-channel-count package. Its rail-to-rail output characteristic is useful for sensor interfaces, low-voltage signal buffers, transducers and portable instrumentation. The manufacturer describes the family as output rail-to-rail micropower operational amplifiers.
The TS941AID is intended for standard general-purpose analog designs rather than high-voltage or high-power applications. Its SOIC package is suitable for conventional PCB assembly, and its small footprint helps reduce board area compared with larger through-hole packages. Because the exact electrical limits depend on the supply voltage and operating conditions, the manufacturer datasheet should be used for input range, output swing, supply current, bandwidth, noise, stability and absolute-maximum-rating checks.
Typical applications include low-voltage sensor interfaces, portable measurement systems, analog signal conditioning, battery-powered instrumentation and small embedded control systems. The single-amplifier arrangement also makes the TS941AID suitable when one channel is sufficient and a larger quad or dual amplifier would add unnecessary board area or cost.
When designing a circuit around the TS941AID, check the datasheet pin description, input common-mode range, output swing, capacitive-load behavior and recommended operating region. Place bypass capacitors close to the supply pins and keep sensitive input routing short to reduce noise pickup and instability.
This page combines manufacturer and distributor information with a practical focus on low-voltage analog design, package reuse, sourcing questions, pinout verification and drop-in replacement planning.
直接替換替代品,適用於 TS941AID — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
此系列的變體
與下列產品可直接替換的同系列型號: TS941AID (相同外形與佔位) — 差異在於 Number of Channels, Package.
TS941AIDT
✅ 直接替換📋 參考替代品(不在目錄中)
MAX4322ESA-T
✅ 直接替換📋 參考替代品(不在目錄中)
OPA343UAG4
✅ 直接替換📋 參考替代品(不在目錄中)
MCP6001-I/SN
✅ 直接替換📋 參考替代品(不在目錄中)
TLV9001IDBVR
✅ 直接替換聯絡詢價
查看資料表 →TS941AID 最大額定值與電氣特性
| Product Type | Operational amplifier |
| Amplifier Type | Single-circuit rail-to-rail operational amplifier |
| Number of Channels | 1 channel |
| Output Topology | Rail-to-rail output |
| Power Class | Micropower operational amplifier |
| Application Category | Instrumentation, operational amplifier and buffer amplifier |
| 封裝 | 8-pin SOIC |
| 安裝類型 | Surface mount |
| Manufacturer | STMicroelectronics |
TS941AID 8-pin soic 腳位配置指南
TS941AID(8-pin soic 封裝)的腳位配置。 此類比元件具有輸入、輸出與電源腳位。偏移歸零、補償與致能腳位配置請參閱製造商資料表。適用於訊號調理與放大器電路。
無詳細腳位定義資料: TS941AID.
請參閱 資料表 以查看完整腳位配置。
典型應用
TS941AID 適用於 6 應用s: Low-Voltage Sensor Interfaces, Portable Measurement Systems, Battery-Powered Industrial Sensors, Embedded Analog Signal Conditioning, Precision Buffering and Level Interfaces, Low-Voltage Audio and Communication Front Ends.
Low-Voltage Sensor Interfaces
The TS941AID fits sensor-conditioning circuits where the sensed output must be amplified while the system operates from a compact supply. Its rail-to-rail output characteristic helps retain signal amplitude near the supply limits, and its micropower classification is appropriate for battery-powered sensing. Place the amplifier close to the sensor or connector, use the manufacturer-recommended supply decoupling and confirm the input common-mode range against the sensor output. The datasheet is required to verify offset, bias current, noise and settling behavior for the selected gain and signal bandwidth.
推薦
Portable Measurement Systems
TS941AID is suitable for portable measurement front ends that need a single rail-to-rail amplifier in a small surface-mount package. The SOIC footprint is easy to assemble and occupies less PCB area than a larger through-hole package. A low-power supply is important for handheld instruments, while the amplifier buffers the source before an ADC or display. Check the TS941AID operating supply range, output swing and gain-bandwidth product in the datasheet, and use short input traces to reduce pickup in the sensitive analog section.
推薦
Battery-Powered Industrial Sensors
The TS941AID can amplify low-level industrial sensor outputs when system power is limited and board space is constrained. Its micropower operational-amplifier designation supports efficient signal conditioning, while rail-to-rail output provides useful headroom in low-voltage signal chains. The design should include local bypass capacitance, a stable reference for any downstream conversion and adequate grounding between the sensor and amplifier. Validate the exact supply current and operating temperature limits against the manufacturer datasheet before using the device in a field-deployed system.
推薦
Embedded Analog Signal Conditioning
TS941AID is useful in embedded control systems that require one buffered analog channel rather than a multi-amplifier package. It can condition a potentiometer, thermistor or other resistive sensor before a controller samples the signal. The single-amplifier configuration simplifies routing and reduces unused circuitry. Confirm the amplifier's input and output ranges for the chosen supply, account for offset and bias-current errors in high-impedance sensor designs, and use the pin-description table in the datasheet to make the final PCB assignments.
推薦
Precision Buffering and Level Interfaces
The TS941AID can buffer a source when the next stage requires a low-impedance drive and the source cannot directly provide the necessary current. Rail-to-rail output makes it useful in low-voltage level-interface arrangements where the output must move close to the supply rails. The op amp is a single amplifier, so a second channel would require another device or a dual-amplifier family member. Verify capacitive-load stability and output-swing limits in the datasheet, especially when driving long PCB traces, ADC inputs or downstream cables.
推薦
Low-Voltage Audio and Communication Front Ends
TS941AID can serve as a general-purpose amplifier stage in low-voltage audio or communication signal paths when the operating conditions remain within the family ratings. Rail-to-rail output helps preserve amplitude in compact systems, and the micropower architecture supports portable equipment. For audio or RF-adjacent circuits, check noise, slew rate, gain stability and bandwidth rather than assuming that a general-purpose op amp is adequate. Use a clean supply, short feedback routing and controlled grounding, and compare the measured performance with the application requirements before production release.
推薦
推薦產品摘要
工程參考資料,適用於 TS941AID — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | TS941AIDT | MAX4322ESA-T | OPA343UAG4 |
|---|---|---|---|---|
| Package | 8-pin SOIC | 8-pin SOIC | SOIC-8 | SOIC-8 |
| Brand | STMicroelectronics | STMicroelectronics | Maxim Integrated | Texas Instruments |
| Amplifier Channels | 1 channel | 1 channel | 1 channel | 1 channel |
| Mounting Type | Surface mount | Surface mount | Surface mount | Surface mount |
主要差異化特點
- Single STMicroelectronics micropower rail-to-rail amplifier (對比MAX4322ESA-T)
- Same-family SOIC alternative (對比TS941AIDT)
- Compact single-channel architecture (對比OPA343UAG4)
- Rail-to-rail output positioning (對比MCP6001-I/SN)
設計說明
Use the manufacturer-recommended supply-bypass capacitors and place them immediately adjacent to the supply pins. The TS941AID is identified as a micropower amplifier, so the actual supply current and the quiescent-current contribution of the complete circuit should be included in battery-life calculations. Confirm the selected supply voltage against the operating and absolute-maximum limits in the datasheet.
Keep the input, feedback and ground paths short and continuous on the 8-SOIC layout. Route sensitive input nets away from switching nodes and high-current return paths, and provide a low-impedance ground reference close to the device. Before layout release, use the manufacturer pin table to assign every pin and confirm that the package orientation matches the PCB footprint.
Do not assume that a rail-to-rail output device can accept every input voltage near the supply rails. Check the input common-mode range, output swing, capacitive-load behavior and stability requirements for the actual operating point. Also verify the exact suffix and temperature grade when using TS941AIDT or another listed candidate as a replacement.
For sensor interfaces, compare the amplifier input bias current and offset voltage with the source impedance. High-impedance sources can amplify offset and leakage errors, so a low-level sensor may require a different input-device family despite the TS941AID's general-purpose positioning. Use the datasheet's typical and maximum characteristics to calculate the resulting error budget.
合規資訊
The current product information confirms the manufacturer, package and amplifier category but does not explicitly state compliance status. Confirm RoHS, REACH, lead-free, halogen-free, conflict-minerals and automotive qualification documentation for the exact ordering code before release.