STMicroelectronics

TS941AID - Rail-to-Rail Micropower Op Amp | STMicroelectronics

N.º de pieza: TS941AID ✓ Activo
8-pin SOIC Package
MOQ: 1 |

TS941AID Descripción general

The STMicroelectronics TS941AID is a single-circuit, rail-to-rail micropower operational amplifier packaged in an 8-pin SOIC. It is designed for general-purpose signal conditioning in low-voltage systems where output swing, low-power operation and compact surface-mount construction are important. The device is identified as an instrumentation, operational-amplifier and buffer-amplifier IC.

Operational amplifiers are analog signal-processing devices that amplify the difference between two input voltages. A rail-to-rail output amplifier can approach its positive and negative supply rails more closely than a conventional amplifier, which helps preserve signal amplitude in low-voltage applications. The micropower operating class of the TS941AID makes it suitable for battery-operated and portable equipment where supply current must remain controlled.

The TS941AID is a single amplifier in an 8-SOIC package, allowing designers to add analog conditioning without using a higher-channel-count package. Its rail-to-rail output characteristic is useful for sensor interfaces, low-voltage signal buffers, transducers and portable instrumentation. The manufacturer describes the family as output rail-to-rail micropower operational amplifiers.

The TS941AID is intended for standard general-purpose analog designs rather than high-voltage or high-power applications. Its SOIC package is suitable for conventional PCB assembly, and its small footprint helps reduce board area compared with larger through-hole packages. Because the exact electrical limits depend on the supply voltage and operating conditions, the manufacturer datasheet should be used for input range, output swing, supply current, bandwidth, noise, stability and absolute-maximum-rating checks.

Typical applications include low-voltage sensor interfaces, portable measurement systems, analog signal conditioning, battery-powered instrumentation and small embedded control systems. The single-amplifier arrangement also makes the TS941AID suitable when one channel is sufficient and a larger quad or dual amplifier would add unnecessary board area or cost.

When designing a circuit around the TS941AID, check the datasheet pin description, input common-mode range, output swing, capacitive-load behavior and recommended operating region. Place bypass capacitors close to the supply pins and keep sensitive input routing short to reduce noise pickup and instability.

This page combines manufacturer and distributor information with a practical focus on low-voltage analog design, package reuse, sourcing questions, pinout verification and drop-in replacement planning.

Alternativas directas para TS941AID — mismo encapsulado, compatible pin a pin. Se excluyen las piezas de otro encapsulado que requieren retrabajo de la PCB.

Variantes de esta serie

Modelos de la misma serie compatibles directamente con TS941AID (mismo factor de forma y huella) — difiere en Number of Channels, Package.

Texas Instruments
Number of Channels: 1
Package: SOT-23-5 (DBV) 2.90 mm x 1.60 mm
Comparar con TS941AID →

TS941AIDT

✅ Sustitución directa
📦 8-pin SOIC
Same TS941 amplifier family and SOIC footprint; the exact ordering suffix and electrical differences are .

📋 Alternativa de referencia (no en el catálogo)

MAX4322ESA-T

✅ Sustitución directa
📦 SOIC-8
Cross-brand rail-to-rail micropower-class SOIC-8 candidate; supply range, offset, bandwidth and stability differences are .

📋 Alternativa de referencia (no en el catálogo)

OPA343UAG4

✅ Sustitución directa
📦 SOIC-8
Cross-brand single-op-amp candidate with an SOIC-8 footprint; input range, bandwidth and supply-current differences are .

📋 Alternativa de referencia (no en el catálogo)

MCP6001-I/SN

✅ Sustitución directa
📦 SOIC-8
Single-amplifier SOIC-8 candidate for low-voltage general-purpose designs; verified electrical differences versus TS941AID are .

📋 Alternativa de referencia (no en el catálogo)

TLV9001IDBVR

✅ Sustitución directa
Texas Instruments
📦 SOT-23-5
1 · CMOS, Rail-to-Rail In/Out · 1.8 V to 5.5 V · 60 uA (typical) · 1 MHz · 2 V/us · 1.6 mV · 2 pA

Consulte el precio

Ver hoja de datos →

TS941AID Valores máximos y características eléctricas

Product Type Operational amplifier
Amplifier Type Single-circuit rail-to-rail operational amplifier
Number of Channels 1 channel
Output Topology Rail-to-rail output
Power Class Micropower operational amplifier
Application Category Instrumentation, operational amplifier and buffer amplifier
Encapsulado 8-pin SOIC
Tipo de montaje Surface mount
Manufacturer STMicroelectronics

Guía de configuración de pines de TS941AID 8-pin soic

Configuración de pines para TS941AID (encapsulado 8-pin soic). Este componente analógico presenta pines de entrada, salida y alimentación. Consulte la hoja de datos del fabricante para conocer las configuraciones de los pines de ajuste de offset, compensación y habilitación. Ideal para circuitos de acondicionamiento de señal y amplificadores.

Diagrama de patillaje del encapsulado 8-pin soic para TS941AID

No hay datos detallados de patillaje disponibles para TS941AID.

Consulte la hoja de datos para ver la configuración completa de patillas.

Aplicaciones típicas

TS941AID es adecuado para 6 aplicacións: Low-Voltage Sensor Interfaces, Portable Measurement Systems, Battery-Powered Industrial Sensors, Embedded Analog Signal Conditioning, Precision Buffering and Level Interfaces, Low-Voltage Audio and Communication Front Ends.

🧩

Low-Voltage Sensor Interfaces

The TS941AID fits sensor-conditioning circuits where the sensed output must be amplified while the system operates from a compact supply. Its rail-to-rail output characteristic helps retain signal amplitude near the supply limits, and its micropower classification is appropriate for battery-powered sensing. Place the amplifier close to the sensor or connector, use the manufacturer-recommended supply decoupling and confirm the input common-mode range against the sensor output. The datasheet is required to verify offset, bias current, noise and settling behavior for the selected gain and signal bandwidth.

📱

Portable Measurement Systems

TS941AID is suitable for portable measurement front ends that need a single rail-to-rail amplifier in a small surface-mount package. The SOIC footprint is easy to assemble and occupies less PCB area than a larger through-hole package. A low-power supply is important for handheld instruments, while the amplifier buffers the source before an ADC or display. Check the TS941AID operating supply range, output swing and gain-bandwidth product in the datasheet, and use short input traces to reduce pickup in the sensitive analog section.

🏭

Battery-Powered Industrial Sensors

The TS941AID can amplify low-level industrial sensor outputs when system power is limited and board space is constrained. Its micropower operational-amplifier designation supports efficient signal conditioning, while rail-to-rail output provides useful headroom in low-voltage signal chains. The design should include local bypass capacitance, a stable reference for any downstream conversion and adequate grounding between the sensor and amplifier. Validate the exact supply current and operating temperature limits against the manufacturer datasheet before using the device in a field-deployed system.

🔧

Embedded Analog Signal Conditioning

TS941AID is useful in embedded control systems that require one buffered analog channel rather than a multi-amplifier package. It can condition a potentiometer, thermistor or other resistive sensor before a controller samples the signal. The single-amplifier configuration simplifies routing and reduces unused circuitry. Confirm the amplifier's input and output ranges for the chosen supply, account for offset and bias-current errors in high-impedance sensor designs, and use the pin-description table in the datasheet to make the final PCB assignments.

⚡

Precision Buffering and Level Interfaces

The TS941AID can buffer a source when the next stage requires a low-impedance drive and the source cannot directly provide the necessary current. Rail-to-rail output makes it useful in low-voltage level-interface arrangements where the output must move close to the supply rails. The op amp is a single amplifier, so a second channel would require another device or a dual-amplifier family member. Verify capacitive-load stability and output-swing limits in the datasheet, especially when driving long PCB traces, ADC inputs or downstream cables.

🌐

Low-Voltage Audio and Communication Front Ends

TS941AID can serve as a general-purpose amplifier stage in low-voltage audio or communication signal paths when the operating conditions remain within the family ratings. Rail-to-rail output helps preserve amplitude in compact systems, and the micropower architecture supports portable equipment. For audio or RF-adjacent circuits, check noise, slew rate, gain stability and bandwidth rather than assuming that a general-purpose op amp is adequate. Use a clean supply, short feedback routing and controlled grounding, and compare the measured performance with the application requirements before production release.

What is the TS941AID?
The TS941AID is a single-circuit, rail-to-rail micropower operational amplifier from STMicroelectronics in an 8-pin SOIC package. According to the manufacturer datasheet, the TS941 family consists of output rail-to-rail micropower operational amplifiers. It is intended for general-purpose low-voltage analog signal conditioning, buffering and instrumentation.
What is the operating voltage range of TS941AID?
The exact TS941AID operating voltage range is [DATA_NEEDED: supply voltage range] and should be confirmed in the manufacturer datasheet before design work begins. The device is identified as a micropower rail-to-rail operational amplifier, but the available product information does not state the minimum and maximum supply voltages. Use the datasheet absolute-maximum and recommended operating sections for those limits.
Where can I download the TS941AID datasheet PDF?
The TS941AID datasheet PDF is available from the linked manufacturer-data source and the product documentation references identify the TS941 as an output rail-to-rail micropower operational amplifier. Use the TS941AID datasheet for the definitive pin description, electrical characteristics, recommended operating conditions and application information.
Where can I find the TS941AID pinout?
The TS941AID uses an 8-pin SOIC, and its pin assignment is documented in the manufacturer datasheet. The available product listings confirm the 8-SOIC package and single-amplifier configuration. Use the datasheet pin-description table when assigning supply, input and output nets, especially before assigning unused or reserved pins.
Is the TS941AID rail-to-rail?
Yes, the TS941AID is identified as an output rail-to-rail micropower operational amplifier. Rail-to-rail output means the output can operate closer to the positive and negative supply limits than a conventional non-rail-to-rail amplifier. The exact output swing, input range and usable frequency-dependent limits are specified in the manufacturer datasheet.
What is the TS941AID used for?
The TS941AID is used for general-purpose low-voltage analog signal conditioning, including sensor interfaces, portable instrumentation, signal buffers and small embedded systems. Its rail-to-rail output is useful when signal swing must be preserved near the supply rails, while its micropower classification supports power-conscious designs.
What is the best drop-in replacement for TS941AID?
The TS941AIDT is the closest documented same-family option because it is associated with the same TS941 amplifier family and SOIC footprint. However, the available cross-reference information does not establish a complete five-part drop-in set with verified electrical equivalence. Confirm pinout, supply range, input range, output swing, bandwidth and stability requirements before substituting any part.
Can MAX4322ESA-T replace TS941AID?
MAX4322ESA-T is a candidate for engineering review because it appears in a comparison against TS941AID, but the available information does not prove that it is a drop-in replacement. The comparison page should be checked for SOIC package, pin assignment, supply voltage, common-mode range, output swing, quiescent current and stability. Do not substitute it without those checks.
Can OPA343UAG4 replace TS941AID?
OPA343UAG4 is a candidate for review because it is listed in a direct comparison with TS941AID, but it cannot be classified as a verified drop-in replacement from the available comparison snippet alone. Confirm whether the package and pinout match the TS941AID and whether the operating voltage, input range, output swing and bandwidth meet the circuit requirements.
When should I choose TS941AID over an alternative op amp?
Choose the TS941AID when you need a single STMicroelectronics rail-to-rail micropower amplifier in an 8-SOIC package and its datasheet limits fit the design. A dual or quad amplifier may be preferable when multiple channels are needed, while another single amplifier may be preferable when its measured noise, bandwidth or supply-current specifications better match the application.
Is TS941AID suitable for low-voltage sensor interfaces?
Yes, TS941AID is suitable for many low-voltage sensor-interface designs because it is a rail-to-rail micropower operational amplifier with a compact SOIC package. Verify the sensor output range against the amplifier input common-mode range and confirm the required settling behavior and noise performance in the manufacturer datasheet.
How much power does TS941AID consume?
The exact TS941AID supply current is [DATA_NEEDED: supply current]. The device is classified as a micropower operational amplifier, so its supply current should be considered in battery and energy-harvesting designs. The datasheet operating table and typical-performance curves provide the appropriate value for the selected supply voltage and output condition.
What is the TS941AID lifecycle status?
The TS941AID is currently listed as active based on the current product and distributor information. For production planning, confirm the lifecycle status and orderable suffixes with the manufacturer or through the Request a Quote form on this page, particularly when designing a long-lived industrial or automotive product.
Is TS941AID compliant with RoHS and REACH?
The RoHS and REACH statuses are [DATA_NEEDED: RoHS status] and [DATA_NEEDED: REACH status] because the current product information does not state them explicitly. For a released production BOM, obtain the manufacturer declaration or product-compliance documentation and confirm the exact ordering code.
Where can I buy TS941AID and what is its lead time?
The TS941AID is available through normal component sourcing channels, and the current distributor results show the exact 8-SOIC ordering code. Use the Request a Quote form on this page for current commercial terms, available quantity and lead time. The quoted commercial response should be used for procurement rather than a historical unit price.

Datos de referencia de ingeniería para TS941AID — comparación, orientación de diseño e información de cumplimiento.

Guía de selección

Choose the TS941AID when the design needs a single STMicroelectronics operational amplifier with rail-to-rail output, micropower characteristics and an 8-SOIC footprint. It is a sensible starting point for low-voltage sensor interfaces, portable measurement circuits and general-purpose analog buffering. TS941AIDT is the closest same-family candidate to evaluate when the exact ordering suffix or packaging arrangement needs review. Consider MAX4322ESA-T or OPA343UAG4 only after checking their datasheets for pin compatibility, supply range, input common-mode range, output swing, bandwidth, noise and capacitive-load stability. A different amplifier may be better when the application requires multiple channels, lower offset, higher bandwidth or a specific automotive qualification. The TS941AID should be selected when its manufacturer-rated operating conditions and stability behavior match the complete signal chain.

Comparación con alternativas

Parámetro Este producto TS941AIDT MAX4322ESA-T OPA343UAG4
Package 8-pin SOIC 8-pin SOIC SOIC-8 SOIC-8
Brand STMicroelectronics STMicroelectronics Maxim Integrated Texas Instruments
Amplifier Channels 1 channel 1 channel 1 channel 1 channel
Mounting Type Surface mount Surface mount Surface mount Surface mount

Diferenciadores clave

  • Single STMicroelectronics micropower rail-to-rail amplifier (frente a MAX4322ESA-T)
  • Same-family SOIC alternative (frente a TS941AIDT)
  • Compact single-channel architecture (frente a OPA343UAG4)
  • Rail-to-rail output positioning (frente a MCP6001-I/SN)

Notas de diseño

Use the manufacturer-recommended supply-bypass capacitors and place them immediately adjacent to the supply pins. The TS941AID is identified as a micropower amplifier, so the actual supply current and the quiescent-current contribution of the complete circuit should be included in battery-life calculations. Confirm the selected supply voltage against the operating and absolute-maximum limits in the datasheet.

Keep the input, feedback and ground paths short and continuous on the 8-SOIC layout. Route sensitive input nets away from switching nodes and high-current return paths, and provide a low-impedance ground reference close to the device. Before layout release, use the manufacturer pin table to assign every pin and confirm that the package orientation matches the PCB footprint.

Do not assume that a rail-to-rail output device can accept every input voltage near the supply rails. Check the input common-mode range, output swing, capacitive-load behavior and stability requirements for the actual operating point. Also verify the exact suffix and temperature grade when using TS941AIDT or another listed candidate as a replacement.

For sensor interfaces, compare the amplifier input bias current and offset voltage with the source impedance. High-impedance sources can amplify offset and leakage errors, so a low-level sensor may require a different input-device family despite the TS941AID's general-purpose positioning. Use the datasheet's typical and maximum characteristics to calculate the resulting error budget.

Información de cumplimiento

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
Libre de plomo
Unknown
Libre de halógenos
Unknown
Minerales en conflicto
Unknown

The current product information confirms the manufacturer, package and amplifier category but does not explicitly state compliance status. Confirm RoHS, REACH, lead-free, halogen-free, conflict-minerals and automotive qualification documentation for the exact ordering code before release.

Datos verificados el: 2026-11-16 — datos verificados y seleccionados por el equipo de ingeniería de componentes de XAIPART

Búsquedas relacionadas

TS941AID datasheet TS941AID pinout TS941AID datasheet pdf TS941AID equivalent TS941AID replacement TS941AID drop-in replacement TS941AID cross reference TS941AID vs MAX4322ESA-T TS941AID vs OPA343UAG4 TS941AID price TS941AID stock STMicroelectronics TS941AID TS941AID SOIC-8 op amp rail-to-rail micropower op amp 8-SOIC TS941AID application circuit

Componentes & términos relacionados

STMicroelectronics TS941AID TS941AIDT MAX4322ESA-T OPA343UAG4 MCP6001-I/SN TLV9001IDBVR Operational amplifier Instrumentation amplifier Buffer amplifier Rail-to-rail output Micropower Low-dropout regulator Voltage regulator Power management IC Analog signal conditioning Sensor interface Battery-powered equipment 8-pin SOIC SOIC package Surface mount SMD Input common-mode range Output voltage swing Gain-bandwidth product Supply current Rail-to-rail input
RFQ de presupuesto rápido
Complete los detalles — nuestro equipo de ventas responderá en un plazo de 24 horas
Número de pieza Fabricante Encapsulado QTY Precio objetivo Total
✓
¡Presupuesto enviado!

Responderemos a su correo electrónico en un plazo de 24 horas

1
RFQ enviado
2
Presupuesto recibido
3
Pedido realizado
4
Pago
5
Enviado
6
Entregado
Ver detalles del RFQ