TS941ILT - RRIO Micropower Op Amp, SOT-23-5 | STMicroelectronics
MPN: TS941ILT ✓ 啟用中TS941ILT 概覽
An operational amplifier is an analog integrated circuit that amplifies the voltage difference between its non-inverting and inverting inputs. The TS941 belongs to the operational-amplifier hierarchy, where it serves as a low-power analog signal-conditioning building block for sensor interfaces, voltage buffers, filters, and low-frequency control circuits. Rail-to-rail input and output behavior is particularly useful when the available signal range occupies much of the supply voltage.
The TS941ILT is a single-circuit device, allowing a compact amplifier layout without the extra channel area of dual or quad alternatives. Its 2.5 V to 10 V operating range supports low-voltage battery-powered systems as well as conventional low-voltage analog circuits. The -40°C to +85°C industrial temperature range provides useful margin for industrial, automotive-adjacent, communications, and instrumentation equipment when the complete system requirements permit that temperature range.
STMicroelectronics describes the TS94x series as micropower operational amplifiers, making the family relevant to designs in which amplifier current consumption contributes materially to overall power budget. Rail-to-rail operation should be considered alongside output-current capability, noise, offset, stability, and slew-rate requirements; those detailed electrical limits should be checked in the manufacturer datasheet before selecting external feedback components or driving heavy loads.
Typical applications include buffering sensor outputs, amplifying low-level analog signals, active filters, threshold detection, and low-frequency signal conditioning. The single SOT-23-5 package also supports portable instruments, battery monitoring systems, industrial transducers, and embedded analog front ends where board area and power consumption are both important design constraints.
For implementation, use the manufacturer pin description table to preserve the correct input, output, supply, and offset-null assignments. Place the bypass capacitor close to the supply pin and route the sensitive input and feedback paths away from switching nodes. Verify stability, output swing, input common-mode behavior, and noise performance at the actual supply voltage and operating temperature.
This product page combines manufacturer-family operating limits with practical application guidance, SOT-23-5 implementation considerations, a parameter-focused comparison, and drop-in screening notes. Those engineering details help narrow the design choice while leaving final suitability decisions to the complete circuit requirements.
直接替換替代品,適用於 TS941ILT — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
此系列的變體
與下列產品可直接替換的同系列型號: TS941ILT (相同外形與佔位) — 差異在於 Amplifier Type, Package.
TS941ILT 最大額定值與電氣特性
| Amplifier Type | Single operational amplifier |
| Operating Supply Voltage Range | 2.5 V to 10 V |
| 工作溫度範圍 | -40°C to +85°C |
| Input Common-Mode Range | Rail-to-rail |
| Output Swing | Rail-to-rail |
| Power Category | Micropower operational amplifier |
| Number of Circuits | 1 circuit |
| 封裝 | SOT-23-5, 5 pins |
| 安裝類型 | Surface mount |
TS941ILT sot-23-5, 5 pins 腳位配置指南
TS941ILT(sot-23-5, 5 pins 封裝)的腳位配置。 此類比元件具有輸入、輸出與電源腳位。偏移歸零、補償與致能腳位配置請參閱製造商資料表。適用於訊號調理與放大器電路。
無詳細腳位定義資料: TS941ILT.
請參閱 資料表 以查看完整腳位配置。
典型應用
TS941ILT 適用於 6 應用s: Battery-Powered Sensor Interfaces, Portable Measurement Instruments, Industrial Transducer Conditioning, Active Audio and Control Filters, Low-Voltage Threshold Detection, Embedded Analog Control Loops.
Battery-Powered Sensor Interfaces
The TS941ILT fits low-voltage sensor front ends that operate from a 2.5 V to 10 V source and need more signal range than a conventional fixed-common-mode amplifier provides. Rail-to-rail input operation helps preserve sensor signals near the supply rails, while the rail-to-rail output stage supports low-swing sensor signals without an external mid-supply reference. The single SOT-23-5 channel also limits board area. Before implementation, verify input bias current against the sensor's source impedance, check offset and noise against the measurement resolution, and confirm that the selected operating voltage remains within the amplifier's stable operating region.
Portable Measurement Instruments
TS941ILT is suitable for portable measurement instruments in which battery life, compactness, and signal-chain flexibility are primary constraints. Its 2.5 V minimum supply supports low-energy operation, while the 5-pin SOT-23-5 package leaves additional board space for the sensor, display interface, or data converter. Rail-to-rail input and output characteristics are valuable when the measured signal occupies much of the available voltage range. Use stable decoupling at the supply pins, keep high-impedance input traces short, and validate gain accuracy, settling time, and output drive at the intended signal frequency before finalizing the analog front end.
Industrial Transducer Conditioning
The TS941ILT can serve as the first active element in a low-level industrial transducer interface, buffering the sensor before additional gain or filtering stages. Its -40°C to +85°C specified operating range is relevant to temperature-controlled industrial equipment, and the single-amplifier SOT-23-5 package simplifies channel isolation. Rail-to-rail behavior increases available input range, but the designer must still check common-mode limits, output swing, offset stability, and noise at the actual bridge or transducer output level. Protective filtering, grounding, and calibrated gain components remain important for repeatable factory measurements.
Active Audio and Control Filters
TS941ILT can implement first-order or higher-order active filtering in low-voltage control and audio-support circuits when its gain-bandwidth, slew-rate, and output-current characteristics satisfy the signal requirements. The rail-to-rail output architecture supports signals approaching the supply limits, which is helpful when the available headroom is limited. Its micropower-oriented family classification is valuable for portable filter blocks. Select resistor and capacitor values using the gain and feedback equations in the manufacturer datasheet, verify noise contribution for high-resolution signals, and probe stability at the target frequency because source loading and capacitive loading can alter closed-loop behavior.
Low-Voltage Threshold Detection
The TS941ILT is applicable to threshold and limit detection where a low-voltage sensor or logic signal must be amplified before comparison. A 2.5 V to 10 V operating range covers common low-voltage rails, and rail-to-rail input behavior improves access to signals near the supply boundaries. The SOT-23-5 package allows several independent detection channels to be placed close to their sources. The amplifier must be configured with suitable positive or negative feedback for the intended switching behavior. Account for input offset, noise, propagation delay through the closed-loop bandwidth, and output saturation margin so the decision threshold remains stable over temperature and supply tolerance.
Embedded Analog Control Loops
TS941ILT can amplify error or feedback signals in embedded analog control loops that require a compact, low-voltage amplifier. Its single-circuit SOT-23-5 footprint is useful when a controller needs one precision conditioning path rather than multiple shared channels. The device can operate across a 2.5 V to 10 V supply range, but loop bandwidth and stability depend on the actual gain network, load, and operating point. Check the amplifier against the controller output range, confirm that the feedback network remains valid over process and temperature variation, and keep sensitive summing nodes compact and shielded from switching-current paths.
工程參考資料,適用於 TS941ILT — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | TS941IDT |
|---|---|---|
| Brand | STMicroelectronics | STMicroelectronics |
| Package | SOT-23-5 | SOT-23-5 |
| Number of Amplifiers | 1 circuit | 1 circuit |
| Operating Supply Voltage Range | 2.5 V to 10 V | 2.5 V to 10 V |
| Operating Temperature Range | -40°C to +85°C | -40°C to +85°C |
| Input Common-Mode Range | Rail-to-rail | Rail-to-rail |
| Output Swing | Rail-to-rail | Rail-to-rail |
| Power Category | Micropower operational amplifier | Micropower operational amplifier |
| Ordering Configuration | TS941ILT | TS941IDT |
主要差異化特點
- Single-channel rail-to-rail micropower architecture in a compact package (對比TS941IDT)
- Operation starts at a 2.5 V supply (對比TS941IDT)
- Wide specified operating-temperature range (對比TS941IDT)
設計說明
Place the supply bypass capacitor directly between the TS941ILT supply pin and ground, with the shortest practical return path. Route the amplifier output away from the capacitor connection point to reduce shared-impedance coupling. Keep the non-inverting and feedback traces short, use a continuous ground reference beneath analog stages, and avoid routing sensitive inputs beneath switching regulators, inductors, or high-current return paths.
Do not assume that rail-to-rail input and output operation permits unlimited input voltage or load current. Check absolute maximum input voltage, common-mode limits, output-current capability, output swing, and short-circuit behavior in the manufacturer datasheet. Also confirm the feedback configuration: the same rail-to-rail output architecture used for positive gain can behave differently when the design attempts operation below the negative supply rail.
Use the gain-bandwidth product and slew-rate limits to define the usable signal bandwidth rather than assuming operation up to the advertised gain. For a noninverting amplifier, the closed-loop bandwidth is approximately gain-bandwidth divided by the closed-loop noise gain. Check capacitive loading at the output and use an isolation resistor if the external load or cable creates stability risk.
The TS941ILT is a micropower amplifier, but real dissipation still depends on supply voltage, output current, and ambient temperature. Keep the SOT-23-5 copper area adequate for heat spreading, avoid enclosing it in a thermally insulating enclosure, and verify the maximum package temperature for the actual board construction. For low-power signal operation, normal board copper is often sufficient, but this must be confirmed rather than assumed.
合規資訊
No explicit environmental or automotive compliance statements were present in the manufacturer product page excerpt. These statuses must be confirmed against the current manufacturer product documentation or declaration for the exact ordering code.