TS941ILT - RRIO Micropower Op Amp, SOT-23-5 | STMicroelectronics
부품 번호: TS941ILT ✓ 활성TS941ILT 개요
An operational amplifier is an analog integrated circuit that amplifies the voltage difference between its non-inverting and inverting inputs. The TS941 belongs to the operational-amplifier hierarchy, where it serves as a low-power analog signal-conditioning building block for sensor interfaces, voltage buffers, filters, and low-frequency control circuits. Rail-to-rail input and output behavior is particularly useful when the available signal range occupies much of the supply voltage.
The TS941ILT is a single-circuit device, allowing a compact amplifier layout without the extra channel area of dual or quad alternatives. Its 2.5 V to 10 V operating range supports low-voltage battery-powered systems as well as conventional low-voltage analog circuits. The -40°C to +85°C industrial temperature range provides useful margin for industrial, automotive-adjacent, communications, and instrumentation equipment when the complete system requirements permit that temperature range.
STMicroelectronics describes the TS94x series as micropower operational amplifiers, making the family relevant to designs in which amplifier current consumption contributes materially to overall power budget. Rail-to-rail operation should be considered alongside output-current capability, noise, offset, stability, and slew-rate requirements; those detailed electrical limits should be checked in the manufacturer datasheet before selecting external feedback components or driving heavy loads.
Typical applications include buffering sensor outputs, amplifying low-level analog signals, active filters, threshold detection, and low-frequency signal conditioning. The single SOT-23-5 package also supports portable instruments, battery monitoring systems, industrial transducers, and embedded analog front ends where board area and power consumption are both important design constraints.
For implementation, use the manufacturer pin description table to preserve the correct input, output, supply, and offset-null assignments. Place the bypass capacitor close to the supply pin and route the sensitive input and feedback paths away from switching nodes. Verify stability, output swing, input common-mode behavior, and noise performance at the actual supply voltage and operating temperature.
This product page combines manufacturer-family operating limits with practical application guidance, SOT-23-5 implementation considerations, a parameter-focused comparison, and drop-in screening notes. Those engineering details help narrow the design choice while leaving final suitability decisions to the complete circuit requirements.
드롭인 대체품: TS941ILT — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 시리즈의 변형
다음과 드롭인 호환되는 동일 시리즈 모델: TS941ILT (동일 폼 팩터 및 풋프린트) — 차이점: Amplifier Type, Package.
TS941IDT
✅ 드롭인 ⚠️ 사양 미검증가격 문의
데이터시트 보기 →TS941ILT 최대 정격 & 전기적 특성
| Amplifier Type | Single operational amplifier |
| Operating Supply Voltage Range | 2.5 V to 10 V |
| 동작 온도 범위 | -40°C to +85°C |
| Input Common-Mode Range | Rail-to-rail |
| Output Swing | Rail-to-rail |
| Power Category | Micropower operational amplifier |
| Number of Circuits | 1 circuit |
| 패키지 | SOT-23-5, 5 pins |
| 실장 유형 | Surface mount |
TS941ILT sot-23-5, 5 pins 핀 구성 가이드
TS941ILT(sot-23-5, 5 pins 패키지)의 핀 구성입니다. 이 아날로그 부품에는 입력, 출력, 전원 공급 핀이 있습니다. 오프셋 널, 보상, 인에이블 핀 구성은 제조사 데이터시트를 참조하십시오. 신호 컨디셔닝 및 증폭기 회로에 이상적입니다.
다음에 대한 상세 핀아웃 데이터 없음: TS941ILT.
다음을 참조하십시오: 데이터시트 전체 핀 구성은 다음을 참조하십시오.
일반적인 애플리케이션
TS941ILT 적합 용도: 6 애플리케이션s: Battery-Powered Sensor Interfaces, Portable Measurement Instruments, Industrial Transducer Conditioning, Active Audio and Control Filters, Low-Voltage Threshold Detection, Embedded Analog Control Loops.
Battery-Powered Sensor Interfaces
The TS941ILT fits low-voltage sensor front ends that operate from a 2.5 V to 10 V source and need more signal range than a conventional fixed-common-mode amplifier provides. Rail-to-rail input operation helps preserve sensor signals near the supply rails, while the rail-to-rail output stage supports low-swing sensor signals without an external mid-supply reference. The single SOT-23-5 channel also limits board area. Before implementation, verify input bias current against the sensor's source impedance, check offset and noise against the measurement resolution, and confirm that the selected operating voltage remains within the amplifier's stable operating region.
Portable Measurement Instruments
TS941ILT is suitable for portable measurement instruments in which battery life, compactness, and signal-chain flexibility are primary constraints. Its 2.5 V minimum supply supports low-energy operation, while the 5-pin SOT-23-5 package leaves additional board space for the sensor, display interface, or data converter. Rail-to-rail input and output characteristics are valuable when the measured signal occupies much of the available voltage range. Use stable decoupling at the supply pins, keep high-impedance input traces short, and validate gain accuracy, settling time, and output drive at the intended signal frequency before finalizing the analog front end.
Industrial Transducer Conditioning
The TS941ILT can serve as the first active element in a low-level industrial transducer interface, buffering the sensor before additional gain or filtering stages. Its -40°C to +85°C specified operating range is relevant to temperature-controlled industrial equipment, and the single-amplifier SOT-23-5 package simplifies channel isolation. Rail-to-rail behavior increases available input range, but the designer must still check common-mode limits, output swing, offset stability, and noise at the actual bridge or transducer output level. Protective filtering, grounding, and calibrated gain components remain important for repeatable factory measurements.
Active Audio and Control Filters
TS941ILT can implement first-order or higher-order active filtering in low-voltage control and audio-support circuits when its gain-bandwidth, slew-rate, and output-current characteristics satisfy the signal requirements. The rail-to-rail output architecture supports signals approaching the supply limits, which is helpful when the available headroom is limited. Its micropower-oriented family classification is valuable for portable filter blocks. Select resistor and capacitor values using the gain and feedback equations in the manufacturer datasheet, verify noise contribution for high-resolution signals, and probe stability at the target frequency because source loading and capacitive loading can alter closed-loop behavior.
Low-Voltage Threshold Detection
The TS941ILT is applicable to threshold and limit detection where a low-voltage sensor or logic signal must be amplified before comparison. A 2.5 V to 10 V operating range covers common low-voltage rails, and rail-to-rail input behavior improves access to signals near the supply boundaries. The SOT-23-5 package allows several independent detection channels to be placed close to their sources. The amplifier must be configured with suitable positive or negative feedback for the intended switching behavior. Account for input offset, noise, propagation delay through the closed-loop bandwidth, and output saturation margin so the decision threshold remains stable over temperature and supply tolerance.
Embedded Analog Control Loops
TS941ILT can amplify error or feedback signals in embedded analog control loops that require a compact, low-voltage amplifier. Its single-circuit SOT-23-5 footprint is useful when a controller needs one precision conditioning path rather than multiple shared channels. The device can operate across a 2.5 V to 10 V supply range, but loop bandwidth and stability depend on the actual gain network, load, and operating point. Check the amplifier against the controller output range, confirm that the feedback network remains valid over process and temperature variation, and keep sensitive summing nodes compact and shielded from switching-current paths.
엔지니어링 참조 데이터: TS941ILT — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | TS941IDT |
|---|---|---|
| Brand | STMicroelectronics | STMicroelectronics |
| Package | SOT-23-5 | SOT-23-5 |
| Number of Amplifiers | 1 circuit | 1 circuit |
| Operating Supply Voltage Range | 2.5 V to 10 V | 2.5 V to 10 V |
| Operating Temperature Range | -40°C to +85°C | -40°C to +85°C |
| Input Common-Mode Range | Rail-to-rail | Rail-to-rail |
| Output Swing | Rail-to-rail | Rail-to-rail |
| Power Category | Micropower operational amplifier | Micropower operational amplifier |
| Ordering Configuration | TS941ILT | TS941IDT |
주요 차별점
- Single-channel rail-to-rail micropower architecture in a compact package (vs TS941IDT)
- Operation starts at a 2.5 V supply (vs TS941IDT)
- Wide specified operating-temperature range (vs TS941IDT)
설계 노트
Place the supply bypass capacitor directly between the TS941ILT supply pin and ground, with the shortest practical return path. Route the amplifier output away from the capacitor connection point to reduce shared-impedance coupling. Keep the non-inverting and feedback traces short, use a continuous ground reference beneath analog stages, and avoid routing sensitive inputs beneath switching regulators, inductors, or high-current return paths.
Do not assume that rail-to-rail input and output operation permits unlimited input voltage or load current. Check absolute maximum input voltage, common-mode limits, output-current capability, output swing, and short-circuit behavior in the manufacturer datasheet. Also confirm the feedback configuration: the same rail-to-rail output architecture used for positive gain can behave differently when the design attempts operation below the negative supply rail.
Use the gain-bandwidth product and slew-rate limits to define the usable signal bandwidth rather than assuming operation up to the advertised gain. For a noninverting amplifier, the closed-loop bandwidth is approximately gain-bandwidth divided by the closed-loop noise gain. Check capacitive loading at the output and use an isolation resistor if the external load or cable creates stability risk.
The TS941ILT is a micropower amplifier, but real dissipation still depends on supply voltage, output current, and ambient temperature. Keep the SOT-23-5 copper area adequate for heat spreading, avoid enclosing it in a thermally insulating enclosure, and verify the maximum package temperature for the actual board construction. For low-power signal operation, normal board copper is often sufficient, but this must be confirmed rather than assumed.
규정 준수 정보
No explicit environmental or automotive compliance statements were present in the manufacturer product page excerpt. These statuses must be confirmed against the current manufacturer product documentation or declaration for the exact ordering code.