集成电路

子分类

📁 ADC/DAC 2519 产品 📁 放大器IC 797 产品 📁 音频编解码器 16 产品 📁 音频IC 2 产品 📁 时钟与计时 302 产品 📁 DSP 963 产品 📁 数据采集IC 2 产品 📁 数字电位器 4 产品 📁 显示驱动与控制器 1 产品 📁 FPGA与CPLD 6666 产品 📁 接口IC 1586 产品 📁 LED驱动器 1 产品 📁 逻辑IC 305 产品 📁 存储IC 875 产品 📁 微控制器 18733 产品 📁 微处理器 4 产品 📁 电机驱动器 1 产品 📁 其他 1 产品 📁 Sensor and Detector Interfaces 1 产品 📁 专用IC 15 产品 📁 视频IC 13 产品

产品（32809)

PIC32CM5164LS60100-I/PF - 48MHz M23 MCU 512KB Flash | Microchip
PIC32CM5164LS60100-I/PF

PIC32CM5164LS60100-I/PF - 48MHz M23 MCU 512KB Flash | Microchip

The Microchip PIC32CM5164LS60100-I/PF is a 32-bit ARM Cortex-M23 microcontroller from the PIC32CM LS60 family, integrating 512 KB Flash and 64 KB SRAM in a 100-pin TQFP package. Operating up to 48 MHz, the device delivers 2.64 CoreMark/MHz and 1.03 DMIPS/MHz, with a 1.62V-3.63V supply range and industrial -40C to +85C temperature grade. The LS60 variant adds hardened security with an integrated Microchip Trust Platform ATECC608 secure element, Arm TrustZone, immutable secure boot, and crypto acceleration. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (Flash), working memory (SRAM), and a rich set of peripherals (ADC, timers, communication controllers). The PIC32CM LS60 belongs to the ultra-low-power Cortex-M23 class, optimized for battery-powered IoT endpoints that need deterministic real-time response plus cryptographic identity for authentication, secure firmware update, and anti-cloning. Within the hierarchy: MCU -> embedded microcontroller -> 32-bit ARM MCU -> Cortex-M23 -> Microchip PIC32CM family. Key features include the integrated ATECC608 secure element (hardware ECC/NIST P-256, secure key storage, ECDH/ECDSA), hardware touch support for capacitive button/slider interfaces, a 12-bit 1 MSPS ADC, two 16-bit DAC channels, four SERCOM-style serial interfaces configurable as UART/SPI/I2C, and a Smart Analog peripheral block. The on-chip Memory Protection Unit (MPU) and TrustZone combine to enforce firmware isolation between secure and non-secure code regions. The LS60 architecture also embeds a SleepWalking peripheral event system, Event System interconnect, and an ultra-low-power RUN/IDLE/STANDYB/STOP/RETENTION/RESET sleep modes family that enables sub-microamp current consumption during duty-cycled sensing, which is critical for coin-cell IoT nodes. Typical applications include secure IoT sensor nodes with authenticated cloud onboarding, capacitive touch user interfaces for white goods and locks, secure medical wearables with encrypted patient data, smart-metering edge nodes, and asset trackers with secure boot and over-the-air firmware updates. Industrial HMI and home-automation keypads also benefit from the integrated touch engine and ATECC608 identity. Designers should budget enough PCB area for a 100-pin TQFP at 14x14 mm (0.5 mm pitch), plan decoupling (100 nF close to each VDD pair plus bulk 4.7 uF), and reserve I/O for the integrated touch channels to fully leverage the MCU's differentiators. Carefully review the secure-element I2C lines - they must remain reachable from the host controller to provision credentials during manufacturing. This page synthesizes distributor pricing, validated drop-in and same-package alternatives, and practical design notes not aggregated on the manufacturer product page.

询价 联系我们
PIC32CM5164LS60100T-I/PF - 512KB Flash Cortex-M23 MCU | Microchip
PIC32CM5164LS60100T-I/PF

PIC32CM5164LS60100T-I/PF - 512KB Flash Cortex-M23 MCU | Microchip

The Microchip Technology PIC32CM5164LS60100T-I/PF is an ultra-low-power 32-bit microcontroller built on the Arm Cortex-M23 core with 512 KB of Flash and 64 KB of SRAM, packaged in a 100-pin TQFP (PF) footprint with industrial -40C to +85C temperature rating. Key features include an integrated Trust Platform ATECC608 secure element, Arm TrustZone for Cortex-M technology, immutable secure boot, and up to 48 MHz CPU clock with SleepWalking peripherals that keep sensors active while the CPU sleeps. The device also integrates a 12-bit ADC, op-amps, DACs, comparators, and a Cryptographic Accelerator supporting AES, SHA, and RSA operations alongside a true random number generator (TRNG). A microcontroller (MCU) is a compact integrated circuit containing a CPU core, program memory, RAM, and programmable peripherals in a single chip. The PIC32CM LS60 family positions itself within the hierarchy of: microcontroller -> 32-bit MCU -> Cortex-M class MCU -> secure low-power MCU -> IoT/edge security MCU -> semiconductor. Compared to legacy PIC24/PIC32MX parts, Cortex-M23 cores execute the Thumb-2 instruction set and deliver higher code density per MHz. The LS60 family is designed for hardened-security IoT endpoints, smart-home hubs, industrial sensor nodes, and touch-enabled human-machine interfaces. Sleep currents in the microamp range and active mode below 100 uA/MHz make it suitable for battery-powered edge devices that must remain in the field for years. The 100-pin TQFP provides abundant GPIO for parallel displays, capacitive touch matrices, and multiple serial interfaces including SERCOM, I2C, SPI, and CAN-FD. Typical applications include secure IoT nodes with certificate-based authentication, industrial HMI panels with touch and TFT support, low-power wireless sensor nodes, smart meters, and home automation gateways. When designing with this device, reserve adequate PCB area for the TQFP-100 footprint and follow the QSPI/SERCOM routing guidance in the Microchip application notes for best EMC performance.

询价 联系我们
PIC32CM6408MC00032-E/PT - 64KB Flash 32-bit M0+ MCU | Microchip
PIC32CM6408MC00032-E/PT

PIC32CM6408MC00032-E/PT - 64KB Flash 32-bit M0+ MCU | Microchip

The Microchip Technology PIC32CM6408MC00032-E/PT is a 32-bit ARM Cortex-M0+ microcontroller with 64KB Flash, 8KB SRAM, and 2KB EEPROM, running up to 48MHz, housed in a 32-pin TQFP (7x7mm) package. It operates from 2.7V to 5.5V, with 26 general-purpose I/O pins, integrated motor-control peripherals (12-bit ADC, 16-bit Sigma-Delta ADC, 10-bit DAC), SERCOM modules, and LIN support. The device is AEC-Q100 qualified for automotive, consumer, commercial, and industrial motor-control applications in electrically noisy environments. A microcontroller (MCU) is a single-chip computer that integrates a processor core, program memory (Flash), data memory (SRAM), and peripheral interfaces. The PIC32CM family belongs to the Cortex-M0+ class - the most energy-efficient ARM core - optimized for low power, deterministic interrupt response, and simple C programming. It sits within the hierarchy: ARM Cortex-M0+ -> 32-bit MCU -> microcontroller -> semiconductor -> embedded system building block. The PIC32CM MC sub-family is purpose-built for motor control, integrating analog front-ends and PWM timers optimized for field-oriented control (FOC) of BLDC, PMSM, and stepper motors. Key features of the PIC32CM6408MC00032-E/PT include 48MHz core clock, 64KB Flash with ECC, 8KB SRAM with ECC, 2KB EEPROM, and an operating temperature range of -40C to +125C (extended automotive grade). Integrated motor-control peripherals include a 16-bit Sigma-Delta ADC (ideal for shunt current sensing), a 12-bit ADC, and a 10-bit DAC for analog feedback loops. Communication interfaces include SERCOM (configurable as UART/SPI/I2C), LIN, and I2S. The Cortex-M0+ core uses a 2-stage pipeline and single-cycle I/O port, offering high code density and deterministic behavior. Hardware CRC, a 32kHz low-power oscillator, and Event System enable low-power operation. The 32-pin TQFP package (7x7mm body) provides ample thermal dissipation and easy hand-soldering for prototype work, while the AEC-Q100 qualification supports automotive under-hood and industrial applications. Typical applications include BLDC/PMSM motor control (fans, pumps, e-bikes), HVAC compressor control, automotive body electronics, industrial drives, and consumer appliances. The wide 5V-tolerant supply rail and 125C temperature grade also suit solar inverters and battery-management interfaces. When designing with this MCU, ensure the supply rail decoupling follows Microchip's recommended 100nF + 4.7uF pattern near VDD pins, and route the analog and digital ground planes carefully to avoid injecting switching noise into the Sigma-Delta ADC inputs. Use MPLAB X IDE with Harmony or MCC for peripheral configuration to accelerate development. This page synthesizes distributor pricing, drop-in same-package alternatives, and practical design notes that supplement the manufacturer datasheet with selection guidance for motor-control system architects.

询价 联系我们
PIC32CM6408MC00032-E/RTB - 48MHz Cortex-M0+ MCU 64KB Flash VQFN-32 | Microchip
PIC32CM6408MC00032-E/RTB

PIC32CM6408MC00032-E/RTB - 48MHz Cortex-M0+ MCU 64KB Flash VQFN-32 | Microchip

The Microchip Technology PIC32CM6408MC00032-E/RTB is an automotive-grade 32-bit ARM Cortex-M0+ microcontroller with 64 KB Flash and 8 KB SRAM, packaged in a 32-pin VQFN (5x5 mm) with an exposed thermal pad and shipped in Tray packaging. The -E temperature variant supports the -40C to +125C extended automotive range and is AEC-Q100 qualified, with the Cortex-M0+ core clocked at 48 MHz for deterministic real-time control. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (Flash), data memory (SRAM), and programmable peripherals (timers, ADC, communication interfaces) onto one die. The PIC32CM MC00 series is classified within the hierarchy: microcontroller -> 32-bit MCU -> ARM Cortex-M0+ MCU -> motor-control MCU -> automotive AEC-Q100 MCU -> embedded system IC. It sits in Microchip's PIC32CM family of 5V-tolerant Cortex-M0+ parts designed for noisy industrial, commercial and automotive environments. Key features include Cortex-M0+ core running at 48 MHz, 64 KB Flash program memory, 8 KB SRAM, 5V-tolerant I/O, and a rich analog (set of motor-control peripherals such as the Analog Comparator and one toggle among PWM, QEI, and PTC/timer signals), plus SERCOM-configurable USART/SPI/I2C and an LIN-capable UART for automotive networks. The integrated Motor Control PWM, Quadrature Encoder Interface (QEI), and 24-bit signal capture chain along with the 24-bit Analog Comparison and one toggle of the 12-bit ADC provide deterministic field-oriented control of BLDC and PMSM motors in noisy environments. The architecture combines an ARM Cortex-M0+ core with Microchip's SAM-style peripheral bus, giving low interrupt latency (12 cycles typical) and DMA-assisted data movement so the CPU can offload motor-control loop housekeeping. The 5V-tolerant I/O and on-chip LIN transceiver support directly address 12V automotive battery rails when paired with an external transceiver. Typical applications include automotive HVAC blower control, BLDC/PMSM field-oriented motor control (sensored for servo pumps, sensorless for fans), 32V-tolerant I/O and fan pump controller, 24-bit signal capture chain along with 12-bit ADC general-purpose industrial control, and consumer 32V-tolerant I/O and home appliance white-goods motor control. The wide 2.7V to 5.5V supply and 5V I/O are particularly valuable in industrial 24V signal nodes. When designing with this device, ensure the PCB provides a sufficient copper pour under the exposed thermal pad and route the SERCOM lines as impedance-controlled differential pairs if using high-speed SPI. The part is AEC-Q100 qualified so for non-automotive-grade variants the PIC32CM8932LS60100-I/PF counterpart is available. This page synthesizes Microchip distributor pricing, AEC-Q100 automotive-grade variants, drop-in same-package alternatives and 32-pin VQFN same-package microcontrollers, plus practical design notes for 5V Cortex-M0+ motor control systems not collected in the manufacturer datasheet.

询价 联系我们
PIC32CM6408MC00032-I/PT - 48MHz Cortex-M0+ 64KB Flash MCU | Microchip
PIC32CM6408MC00032-I/PT

PIC32CM6408MC00032-I/PT - 48MHz Cortex-M0+ 64KB Flash MCU | Microchip

The Microchip Technology PIC32CM6408MC00032-I/PT is a 32-bit ARM Cortex-M0+ microcontroller designed for motor control and rugged 5V applications, featuring 64 KB Flash, 8 KB SRAM, and 2 KB EEPROM in a 32-pin TQFP (7x7 mm) package. It operates up to 48 MHz with a single-core architecture and provides 26 GPIO pins for peripheral expansion, plus integrated motor control peripherals such as PWM, ADC, and analog comparators. A microcontroller (MCU) is a single-chip computer containing a processor core, program memory (Flash), working memory (RAM), data EEPROM, and a rich set of on-chip peripherals. In the broader taxonomy, the PIC32CM MC00 family sits under 32-bit microcontrollers, then ARM Cortex-M0+ based MCUs, then microcontrollers, then embedded semiconductors. This 5V-tolerant family is engineered for consumer, commercial, industrial, and automotive use in electrically noisy environments where 3.3V-only parts would be unreliable. Key features include a wide 2.7 V to 5.5 V supply range, hardware LIN support, multiple SERCOM-style serial interfaces (I2C, SMBus, IrDA, RS-485), 12-bit ADC, and a powerful motor control PWM with complementary outputs and dead-band insertion. The device also integrates a true random number generator (TRNG) and supports capacitive touch via the Peripheral Touch Controller (PTC), enabling HMI and motor drive combinations on a single die. Architecturally, the PIC32CM MC00 combines an ARM Cortex-M0+ core licensed from Arm with Microchip's proprietary peripheral set and CIP (Core Independent Peripherals) such as the Event System, Configurable Custom Logic (CCL), and motor-control timer/counter. Designers benefit from the dual ecosystem: the ARM toolchain (CMSIS, GCC, IAR, Keil) for code development, plus Microchip's MPLAB X IDE, MCC code generator, and Harmony framework for middleware and motor-control libraries. Typical applications include BLDC and PMSM motor drives (fans, pumps, appliance compressors), HVAC actuators, e-bike controllers, power tools, automotive body and accessory modules, and industrial sensor hubs. The 5V tolerance and LIN bus support make it a strong fit for cost-sensitive nodes that previously relied on 8-bit MCUs but need Cortex-M0+ compute for field-oriented control (FOC). When designing with this part, allocate the 8 KB SRAM carefully - use the 2 KB EEPROM for non-volatile parameter storage to avoid wear-leveling on Flash, and reserve DMA channels for high-speed ADC-to-PWM data paths in motor loops. The 32-pin TQFP leaves limited analog channel count; choose the 48- or 64-pin variants if more ADC inputs or PWMs are required. This page synthesizes distributor pricing, drop-in pin-compatible alternatives across the PIC32CM MC00 family, and practical design notes not found in the manufacturer datasheet.

询价 联系我们
PIC32CM6408MC00032-I/RTB - 48MHz 32-VQFN Motor Control MCU | Microchip
PIC32CM6408MC00032-I/RTB

PIC32CM6408MC00032-I/RTB - 48MHz 32-VQFN Motor Control MCU | Microchip

The Microchip Technology PIC32CM6408MC00032-I/RTB is a 5V ARM Cortex-M0+ microcontroller in the PIC32CM MC00 family, integrating 64KB Flash, 8KB SRAM, and 2KB EEPROM in a 32-pin VQFN (5x5 mm) package. It runs at up to 48 MHz, supports 2.7V to 5.5V operation, and exposes 26 general-purpose I/O for motor-control and industrial front-ends. The -I suffix denotes the industrial -40C to +85C temperature grade; the RTB suffix indicates tape-and-reel packaging on the 32-VQFN (RTB) footprint. A microcontroller (MCU) is an integrated circuit that combines a CPU core, program memory, working RAM, and a rich set of peripherals (ADC, timers, communication interfaces) on a single die. PIC32CM MC00 parts sit inside the broader PIC32CM family (32-bit Cortex-M0+), which itself belongs to Microchip's 32-bit PIC32 MCU portfolio. The MC sub-family adds dedicated peripherals for motor-control loops such as PWM, encoder interfaces, and high-speed ADCs, placing these MCUs in the power-management and motor-drive segment of Microchip's product hierarchy. Key features include the SERCOM-configurable serial engine (USART/SPI/I2C), built-in LIN support for automotive body networks, a 12-bit ADC with up to 1 Msps, and multiple 16-bit timers suitable for field-oriented control (FOC) of brushless DC (BLDC) and permanent-magnet synchronous motors (PMSM). The Cortex-M0+ core delivers deterministic interrupt latency and is supported by Microchip's MPLAB X IDE, MPLAB Harmony, and the XC32 toolchain, plus the open-source Keil MDK-Arm environment for migration projects. Typical applications span consumer appliances (small fans, pumps, vacuum robots), commercial HVAC dampers, industrial low-power motor drives, automotive body modules (seat/door/window, LIN nodes), and general-purpose 5V embedded replacements for legacy PIC16/PIC24 designs. The wide 2.7V-5.5V supply range means the part can be powered directly from a USB rail, a 3.3V LDO, or a 5V switching pre-regulator without level shifters on most signals. When designing with this MCU, allocate one SERCOM instance per communication channel and reserve one ADC channel per phase current shunt for FOC firmware. Program Flash endurance is 10k cycles typical; the integrated EEPROM block eliminates external non-volatile storage for parameter retention tasks.

询价 联系我们
PIC32CM6408MC00032T-I/PT - 48MHz Cortex-M0+ 64KB Flash MCU | Microchip
PIC32CM6408MC00032T-I/PT

PIC32CM6408MC00032T-I/PT - 48MHz Cortex-M0+ 64KB Flash MCU | Microchip

The Microchip PIC32CM6408MC00032T-I/PT is a 32-bit ARM Cortex-M0+ microcontroller from the PIC32CM MC family, integrating 64 KB of Flash, 8 KB of SRAM and 2 KB of EEPROM, and operating at up to 48 MHz core frequency in a 32-pin TQFP (7x7 mm) package with 26 GPIO. The device is fabricated on a 5V-tolerant CMOS process, runs from a 2.7 V to 5.5 V supply, and includes a dedicated motor-control PWM subsystem, making it targeted at brushless DC (BLDC), permanent-magnet synchronous motor (PMSM) and switched reluctance drives. What is a microcontroller (MCU)? A microcontroller is a single-chip computer containing a CPU core, non-volatile program memory, working RAM, and a rich set of on-chip peripherals such as timers, ADCs, communication interfaces and PWM channels. Within the embedded hierarchy, an MCU sits below microprocessors (MPUs) in integration and is the central building block of virtually every embedded product - from consumer appliances and IoT nodes to industrial automation, automotive body and motor-control modules. The PIC32CM series combines an ARM Cortex-M0+ core (a widely adopted 32-bit architecture from ARM) with Microchip's 5V-tolerant peripherals. Key features of the PIC32CM6408MC00032T-I/PT include its motor-control PWM peripheral (designed for 3-phase field-oriented control), 12-bit ADC with up to 12 channels, multiple SERCOM-style USART/SPI/I2C serial interfaces, and 32 KB of user-configurable Flash for boot/option storage. The device's industrial-grade -40C to +85C temperature range and automotive-targeted peripherals allow it to be deployed in harsh-electrical environments where ESD and conducted noise are common. Compared to legacy PIC16/PIC24 parts, the Cortex-M0+ core offers cleaner toolchain support via GCC, IAR and Keil. From an architectural standpoint, the PIC32CM MC family uses a Harvard bus architecture with separate code and data paths to the Flash and SRAM, plus a tightly coupled EEPROM block for non-volatile data. The motor-control PWM unit supports complementary outputs, programmable dead-time, ADC trigger, and fault inputs, allowing direct interface to a 3-phase gate driver such as the Microchip MCP8024 or dsPIC33 companion parts. Typical applications include 3-phase BLDC/PMSM motor drives (fans, pumps, e-bikes, appliances), HVAC damper and compressor control, industrial servo and stepper control front-ends, automotive auxiliary pumps and fans, and low-cost 5V industrial sensor hubs. The wide 2.7 V to 5.5 V supply range also supports 3.3 V and 5 V mixed-signal designs without level shifters. When designing with this MCU, ensure your PWM switching frequency and dead-time are sized to the chosen MOSFET/IGBT driver. Place the ADC sample-and-hold capacitor close to the MCU and use the dedicated analog VDD/VSS pins; the integrated Cortex-M0+ core simplifies firmware migration from other ARM parts. This page synthesizes distributor pricing, drop-in alternatives, and practical motor-control design notes not always collected in the manufacturer datasheet.

询价 联系我们
PIC32CM6408MC00032T-I/RTB - 48MHz Cortex-M0+ MCU, 64KB Flash | Microchip
PIC32CM6408MC00032T-I/RTB

PIC32CM6408MC00032T-I/RTB - 48MHz Cortex-M0+ MCU, 64KB Flash | Microchip

The Microchip Technology PIC32CM6408MC00032T-I/RTB is a 32-bit ARM Cortex-M0+ microcontroller from the PIC32CM MC family, integrating 64KB Flash and 8KB SRAM, operating at up to 48MHz, and housed in a 32-pin VQFN (5x5 mm) package with industrial -40C to +85C temperature rating. Designed for motor control and noisy-environment applications, the part combines a 5V-tolerant core with the Cortex-M0+ instruction set, providing deterministic performance for real-time control loops. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, volatile and non-volatile memory, peripherals, and I/O onto one die; the Cortex-M0+ is an ARM architecture that emphasizes small footprint, low power, and deterministic interrupt latency, while the PIC32CM MC family is Microchip's 5V-tolerant extension of that core aimed at consumer, commercial, industrial, and automotive nodes where higher-voltage signaling is common. The 'MC' suffix indicates the inclusion of motor-control PWMs, fast ADC, and op-amps optimized for field-oriented control of brushed, brushless DC, and stepper motors. Key features include 64KB on-chip Flash, 8KB SRAM, hardware multiplier and divider, a 12-bit ADC with up to 16 channels, multiple SERCOM-configurable serial interfaces, and integrated PWM channels with complementary outputs and dead-band generation. The 5V-tolerant I/O simplifies interfacing to legacy analog signal chains without external level shifters, and the dedicated PWM/ADC synchronization logic supports center-aligned and edge-aligned switching patterns typical of FOC motor loops. On the architectural side, the device pairs the Cortex-M0+ core (Armv6-M, Thumb/Thumb-2 instructions) with Microchip peripheral IP, including the SERCOM module (re-configurable as UART, SPI, or I2C), a 16-bit timer/counter array, and motor-control PWM with fault inputs. The 32-VQFN package exposes a high-pin-count variant suitable for three-phase motor drive boards, while the 5V-tolerant pads ease industrial bus compliance. Typical applications include BLDC/PMSM motor control, ceiling fans and pumps, appliance motor drives, HVAC actuators, automotive body and LIN nodes, and industrial servo controllers. The wide temperature range and 5V tolerance make the family especially well suited to appliances and 12V/24V industrial subsystems. When designing with this device, plan for a stable 5V or 3.3V supply rail, dedicate the motor-control PWM channels to a three-phase H-bridge gate driver, and use the integrated op-amps for current shunt amplification to keep the BOM small.

询价 联系我们
PIC32CM6408MC00048-E/U5B - 64KB Flash Cortex-M0+ MCU w/ Motor Control | Microchip
PIC32CM6408MC00048-E/U5B

PIC32CM6408MC00048-E/U5B - 64KB Flash Cortex-M0+ MCU w/ Motor Control | Microchip

The Microchip PIC32CM6408MC00048-E/U5B is a 32-bit ARM Cortex-M0+ microcontroller engineered for motor control and noisy-environment applications, integrating 64KB of Flash and 8KB of SRAM in a 48-pin VQFN (7x7 mm) package. The part operates at up to 48 MHz with a single-core architecture and is qualified to AEC-Q100 for automotive deployment. An MCU (microcontroller unit) is a single-chip computer containing a CPU core, program memory (Flash), working memory (SRAM), and a rich set of on-chip peripherals. In the product hierarchy it sits inside the broader class of microcontrollers -> embedded processors -> semiconductor ICs. The Cortex-M0+ core is the smallest and most energy-efficient member of the ARM Cortex-M family, designed for deterministic real-time control with a streamlined instruction set and Thumb-2 support. This PIC32CM MC variant extends the core with motor-control PWMs, 5V-tolerant I/O, and CAN-FD capable peripherals. Key features include 64KB on-chip Flash (64K x 8), 8KB SRAM, 48 MHz max CPU clock, integrated motor-control PWM peripherals, SERCOM-style serial interfaces, and LIN support. The 48-VQFN package offers an exposed thermal pad and compact 7x7 mm footprint, making the part suitable for space-constrained BLDC, PMSM, and stepper drive boards. Architecturally, the PIC32CM MC combines an ARM Cortex-M0+ core with Microchip's PIC-style peripheral set, giving designers a familiar MPLAB X IDE workflow with Cortex-M toolchain support. The 5V-tolerant I/O and AEC-Q100 qualification make it robust against electrical noise typical in automotive and industrial environments. Typical applications include BLDC and PMSM motor controllers, automotive body and comfort modules, industrial sensor nodes, and consumer appliances. The combination of motor-control PWMs, CAN/LIN, and 5V I/O lets a single part serve as the system controller without external glue logic. When designing with this device, ensure the PCB provides adequate copper under the exposed pad for thermal dissipation and that the supply rail is decoupled with 100 nF + bulk ceramic per the datasheet. Review the device errata for any pre-silicon silicon revisions before committing to high-volume production. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet, giving engineers a one-stop reference for selection and sourcing decisions.

询价 联系我们
PIC32CM6408MC00048-E/Y8X - 48MHz Cortex-M0+ MCU | Microchip
PIC32CM6408MC00048-E/Y8X

PIC32CM6408MC00048-E/Y8X - 48MHz Cortex-M0+ MCU | Microchip

The Microchip PIC32CM6408MC00048-E/Y8X is a 32-bit ARM Cortex-M0+ microcontroller from the PIC32CM-MC family, featuring 64KB Flash, 8KB SRAM, and a 48MHz core speed in a 48-pin TQFP (7x7 mm) package. It integrates advanced motor control peripherals (PWM, QEI, ADC with hardware triggering) and is AEC-Q100 qualified for automotive, industrial, and commercial applications operating up to 125C. The device is part of Microchip's 5V tolerant PIC32CM series designed for noisy environments. An ARM Cortex-M0+ microcontroller is a low-power, energy-efficient 32-bit processor core featuring a von Neumann architecture with a single-cycle hardware multiplier, Thumb/Thumb-2 instruction support, and tightly coupled peripherals for deterministic embedded control. Within the hierarchy: microcontroller -> MCU -> embedded processor -> semiconductor, the M0+ class is the smallest and most power-efficient ARM core, typically used in cost-sensitive real-time control applications like motor control, sensor hubs, and IoT endpoints. Key features of the PIC32CM6408MC00048 include 64KB Flash program memory, 8KB SRAM, integrated SERCOM configurable as UART/SPI/I2C, a 12-bit ADC with up to 16 channels, multiple 16-bit timer/counters, and motor-control-specific peripherals such as the PWM with complementary outputs and quadrature encoder interface. The 5V tolerant I/O and wide operating voltage range (2.7V-5.5V) make it suitable for industrial and automotive noise environments. Technical depth: the device uses Microchip's proprietary on-chip debug (SWD) and supports MPLAB X IDE plus Harmony 3 framework. The motor-control PWM engine supports edge-aligned, center-aligned, and variable-frequency modes, enabling Field-Oriented Control (FOC) of 3-phase BLDC and PMSM motors. Hardware fault protection (current-limit, over-voltage) integrates without CPU intervention, critical for safety-relevant drives. Typical applications include BLDC/PMSM motor control in appliances and automotive auxiliaries, HVAC fan and pump control, e-bike and small-EV traction, industrial servo drives, and consumer appliances requiring quiet operation. The integrated motor-control peripherals reduce external component count versus discrete MCU + gate-driver architectures. When designing with this MCU, ensure decoupling on VDD/AVDD pairs and provision for the SWD interface to retain in-circuit programming capability. Use the Harmony 3 motor-control framework to accelerate development, but note that core mark-up at 48MHz places performance ceilings on high-end FOC loops. This page synthesizes distributor pricing from LCSC, DigiKey, Mouser, real-time stock indicators, and engineering application notes specific to motor-control design - not found in the manufacturer datasheet alone.

询价 联系我们
PIC32CM6408MC00048-I/Y8X - 48MHz Cortex-M0+ MCU | Microchip
PIC32CM6408MC00048-I/Y8X

PIC32CM6408MC00048-I/Y8X - 48MHz Cortex-M0+ MCU | Microchip

The Microchip Technology PIC32CM6408MC00048-I/Y8X is a 32-bit ARM Cortex-M0+ microcontroller engineered for motor control and robust industrial applications. It integrates 64KB of Flash memory, 8KB of SRAM, and runs at a maximum CPU speed of 48MHz, all housed in a 48-pin TQFP (7x7 mm) package. The device operates across a wide 2.7V to 5.5V supply range and is rated for industrial temperature operation from -40C to +85C. A 32-bit microcontroller is an integrated circuit that combines a 32-bit processor core, program memory (Flash), data memory (SRAM), and a rich set of peripherals on a single silicon die. Within the broader hierarchy, this part is a member of the MCU (microcontroller unit) class of semiconductors, which sits under the Embedded IC family in the larger Power Management and Embedded Systems category. The Cortex-M0+ core used here is instruction-set compatible with the earlier Cortex-M0 and is upward-compatible with Cortex-M3/M4 designs, simplifying software portability. Key features of the PIC32CM6408MC00048-I/Y8X include dedicated motor-control peripherals (PWM, encoder interface, and 12-bit ADC with dedicated sample-and-hold), SERCOM-configurable serial interfaces for UART/SPI/I2C, an on-chip 12-bit ADC, and a Peripheral Touch Controller (PTC). It also features an integrated LIN transceiver interface, making it well suited to automotive body and comfort networks. The architecture combines a deterministic Cortex-M0+ core with Microchip's SAM-style peripheral set, allowing deterministic motor control loops while retaining easy code development in MPLAB X IDE and MPLAB Harmony. The wide 5V-tolerant I/O and 5V supply tolerance simplify interfacing to legacy industrial sensors and actuators without level shifters. Typical applications include BLDC and PMSM motor control (fans, pumps, small appliances), HVAC actuators, industrial sensor nodes, automotive body controllers, consumer appliances with capacitive touch, and LIN-connected slave nodes. According to the PIC32CM MC00 Family Data Sheet, the device family is qualified for consumer, commercial, industrial, and automotive use. When designing with this MCU, ensure adequate decoupling (100nF + 1uF minimum) close to the supply pins, route the analog and digital ground domains separately, and reserve a dedicated trace for the crystal or external clock. The integrated peripherals reduce external BOM cost, but motor-control loops still benefit from a 4-layer PCB with a continuous ground plane. This page synthesizes distributor pricing, same-brand drop-in variants, and practical design notes not found in the manufacturer datasheet alone.

询价 联系我们
PIC32CM6408MC00048T-I/U5B - 48MHz Cortex-M0+ MCU 64KB Flash | Microchip
PIC32CM6408MC00048T-I/U5B

PIC32CM6408MC00048T-I/U5B - 48MHz Cortex-M0+ MCU 64KB Flash | Microchip

The Microchip PIC32CM6408MC00048T-I/U5B is a 32-bit ARM Cortex-M0+ microcontroller from the PIC32CM MC family, featuring 64KB Flash, 8KB SRAM, and a 48MHz core clock in a 48-pin VQFN (7x7 mm) package with wettable flank leads. It is designed for motor control, consumer, commercial, industrial, and automotive applications operating in electrically noisy environments, and integrates dedicated motor-control peripherals alongside the SERCOM serial-communication module and LIN support. What is a Cortex-M0+ microcontroller? An ARM Cortex-M0+ MCU is an ultra-low-power 32-bit microcontroller core built on the ARMv6-M architecture, optimized for deterministic interrupt response, low active-current draw, and minimal die area. It sits below Cortex-M3/M4 cores in the ARM hierarchy and is widely used as the main processor in motor-control, sensor-interface, and battery-powered embedded designs where simple deterministic control loops dominate the workload. Key features of the PIC32CM6408MC00048T-I/U5B include 64KB of on-chip Flash (64K x 8), 8KB SRAM, a 48MHz maximum CPU clock, and an integrated motor-control peripheral set tailored for field-oriented control (FOC) of BLDC and PMSM motors. The 5V-tolerant I/O and LIN transceiver support make it robust for harsh industrial and automotive buses, while the 48-VQFN (U5B) package with wettable flanks enables reliable automated optical inspection (AOI) on high-volume production lines. Architecturally, the device pairs the Cortex-M0+ core with Microchip's PIC32CM MC motor-control IP, multiple 16-bit timers with PWM, a 12-bit analog-to-digital converter (ADC), and SERCOM instances configurable as USART, I2C, or SPI. This integration eliminates the need for an external motor-control coprocessor, reducing both BOM cost and PCB area in compact variable-frequency-drive designs. Typical applications include BLDC and PMSM motor control (fans, pumps, e-bikes, drones), field-oriented-control compressor drives for HVAC, appliance motor boards, small appliance control, automotive body and accessory ECUs, and industrial sensor-actuator nodes. The wide operating temperature range (industrial -40C to +85C) supports outdoor and under-hood deployments. When designing with this part, allocate sufficient copper area beneath the exposed pad for thermal dissipation, especially in continuous high-current PWM drive stages, and follow Microchip AN2520 motor-control layout guidelines to minimize dv/dt-induced noise on the ADC sense paths. This page synthesizes distributor pricing, parametric proximity to drop-in alternatives, and practical motor-control design guidance not consolidated on any single distributor page.

询价 联系我们
PIC32CM6408MC00048T-I/Y8X - 64KB Flash ARM Cortex-M0+ MCU | Microchip
PIC32CM6408MC00048T-I/Y8X

PIC32CM6408MC00048T-I/Y8X - 64KB Flash ARM Cortex-M0+ MCU | Microchip

The Microchip PIC32CM6408MC00048T-I/Y8X is a 32-bit ARM Cortex-M0+ microcontroller in the PIC32CM MC family, integrating 64KB Flash and 8KB SRAM with dedicated motor-control peripherals in a 48-pin TQFP (Y8X) package. The device is built around the Cortex-M0+ core running at up to 48 MHz and is targeted at 5V-tolerant consumer, commercial, industrial and automotive motor-control applications in electrically noisy environments. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (Flash), working memory (SRAM), and a rich set of peripherals such as timers, ADCs, communication interfaces, and - in the MC family - motor-control PWM and quadrature decoder blocks. MCUs sit at the heart of every embedded system, replacing discrete logic and providing configurable, software-defined control. The PIC32CM MC family inherits Microchip's SAM heritage and combines it with PIC ecosystem familiarity. Key features of the PIC32CM6408MC00048T-I/Y8X include 64KB (64K x 8) Flash, 8KB SRAM, a 32-bit single-core Cortex-M0+ CPU at 48 MHz, and an integrated Peripheral Touch Controller (PTC) supporting capacitive touch sensing. The MC variant additionally provides dedicated motor-control peripherals including a 24-bit motor-control PWM, a quadrature encoder interface, and analog comparators with DAC references for current-shunt sensing, making it a single-chip solution for brushless DC (BLDC) and permanent-magnet synchronous motor (PMSM) control. The architecture leverages the Cortex-M0+ v6-M instruction set with a single-cycle IO bus for deterministic GPIO response, and integrates SERCOM-configurable serial interfaces that can be assigned to USART, I2C, or SPI roles. With 5V-tolerant I/O and an operating voltage range of 2.7V to 5.5V, the device interfaces directly to 5V gate drivers and Hall-effect sensors without level shifters. The 48-pin TQFP package provides ample I/O for parallel motor bridges, encoder signals, and CAN/LIN transceivers required for body and industrial control modules. Typical applications include sensorless and sensored BLDC fan and pump controllers, HVAC blower motors, small appliance drives, robotic joint controllers, e-bike traction units, and industrial servo amplifiers. The MC peripherals also suit LED lighting drivers and power-conversion control loops where precise PWM edge placement matters. When designing with this part, designers should add 0.1uF + 10uF decoupling at every supply pin, route the analog AGND and digital GND back to a single star point under the exposed pad, and follow the Microchip AN2685 motor-control layout guide for high-current switching loops to avoid tripping the brown-out detector. This page synthesizes distributor pricing, pin-compatible alternatives, and practical motor-control layout notes not consolidated in the manufacturer datasheet, providing engineers with a one-stop reference for evaluating the PIC32CM6408MC00048T-I/Y8X against competing 48 MHz Cortex-M0+ motor-control MCUs.

询价 联系我们
PIC32MK0256GPG048-E/7MX - 32-bit 80MHz MCU, 256KB Flash, 48-VQFN | Microchip
PIC32MK0256GPG048-E/7MX

PIC32MK0256GPG048-E/7MX - 32-bit 80MHz MCU, 256KB Flash, 48-VQFN | Microchip

The Microchip Technology PIC32MK0256GPG048-E/7MX is a high-performance 32-bit microcontroller built on the MIPS32 microAptiv core, integrating a single-core 80MHz CPU with DSP and FPU capabilities. The device delivers 256KB of ECC-protected Flash and 64KB of SRAM in a compact 48-pin VQFN (6x6 mm) package with wettable flanks for automated optical inspection. A 32-bit microcontroller (MCU) is an integrated circuit that combines a microprocessor core, program memory (Flash), data memory (SRAM), and programmable peripherals on a single silicon die. Within the broader hierarchy, a 32-bit MCU sits above 16-bit MCUs and 8-bit MCUs in computational capability, and below application-specific SoCs and microprocessors (MPU). The PIC32MK family specifically targets motor control, digital power conversion, industrial automation, and IIoT applications requiring deterministic real-time performance and DSP-grade signal processing. Key features include 120MHz maximum MIPS performance, an integrated single-precision FPU and DSP extensions for efficient signal-processing workloads, a 12-bit ADC with up to 18 analog channels, dual 12-bit DACs, and CAN FD connectivity for industrial networking. The integrated DSP instructions accelerate motor-control loops, digital filtering, and field-oriented control (FOC) algorithms without offloading to a companion DSP chip. The architecture combines a 5-stage pipeline MIPS32 microAptiv core with tightly-coupled SRAM, configurable instruction cache, and a peripheral set mapped through a multi-channel DMA engine. ECC protection on Flash improves reliability in safety-critical applications, while the wettable-flank QFN package enhances solder-joint inspection yield on automotive-grade production lines. Typical applications include brushless DC (BLDC) and permanent-magnet synchronous motor (PMSM) control, industrial servo drives, solar micro-inverters, digital power conversion, CAN-FD networked sensors, and IIoT edge nodes. The PIC32MK0256GPG048-E/7MX in particular suits compact designs requiring CAN-FD, dual DAC outputs, and 18-channel ADC sampling. When designing with this part, allocate the 80MHz system clock and DSP pipeline carefully - sustained DSP workloads require deterministic interrupt latency. The wettable-flank QFN footprint simplifies AOI inspection but requires proper pad geometry to ensure reliable solder joints on the 0.4mm pitch. This page synthesizes distributor pricing, drop-in same-family alternatives, and practical design notes beyond the manufacturer datasheet, providing a single reference for engineers evaluating the PIC32MK0256GPG048-E/7MX for motor-control and IIoT designs.

询价 联系我们
PIC32MK0256GPG048T-E/Y8X - 32-bit 80MHz 256KB FLASH MCU | Microchip
PIC32MK0256GPG048T-E/Y8X

PIC32MK0256GPG048T-E/Y8X - 32-bit 80MHz 256KB FLASH MCU | Microchip

The Microchip Technology PIC32MK0256GPG048T-E/Y8X is a 32-bit MIPS32 microAptiv PIC32MK microcontroller featuring 256 KB of ECC-protected Flash program memory, 64 KB of SRAM, and a maximum CPU clock of 80 MHz (the GPG sub-family is the 80 MHz tier, distinct from the 120 MHz MCJ/MCM tiers). It integrates 18 channels of 12-bit Analog-to-Digital Conversion (ADC), 2 channels of 12-bit Digital-to-Analog Conversion (DAC), and a peripheral set targeting general-purpose embedded control. The device is housed in a 48-pin TQFP (7x7 mm) package with an operating voltage range of 2.3 V to 3.6 V and an automotive-grade -40 C to +125 C operating junction temperature window. What is a PIC32MK microcontroller? A PIC32MK MCU is a 32-bit Flash microcontroller built on the MIPS32 microAptiv core from Microchip Technology, positioned within the broader taxonomy as: PIC32MK -> PIC32 family -> 32-bit MCU -> microcontroller -> embedded IC. Compared to traditional 8-bit PIC MCUs, the PIC32MK offers higher computational throughput, larger memory addressing, DSP instructions, and a richer analog/motor-control peripheral set, placing it in the middle of Microchip's 32-bit MCU portfolio between lower-power PIC32MX and higher-end SAM devices. Key features include up to 256 KB Flash with ECC, 64 KB SRAM, 80 MHz core frequency with a 4-stage pipeline MIPS32 core, hardware multipliers for DSP, dual I2C, I2S, SPI, and UART interfaces, and multiple general-purpose timers. The 12-bit ADC supports up to 18 channels with sample-and-hold for multi-channel analog sampling, and the 12-bit DAC provides two channels for waveform generation or bias control without external components. The PIC32MK0256GPG048T-E/Y8X uses the MIPS32 microAptiv core with DSP and microMIPS ISA support, allowing tight C-code density and deterministic interrupt latency. ECC on Flash and SRAM supports functional-safety applications where single-event upsets must be detected, and the integrated dual-bank Flash allows live firmware updates via in-application programming. Internal PLLs and a flexible clock tree support multiple oscillator sources for noise-immune motor-control loops. Typical applications include BLDC/PMSM motor control (FOC), industrial sensor conditioning, building automation, LED lighting control, low-cost HMI panels, USB-to-UART bridges, and automotive body ECUs. The wide temperature range and ECC memory make it especially attractive for automotive body and chassis subsystems and industrial sensor hubs requiring long-term reliability. When designing with this part, allocate adequate decoupling (100 nF + 1 uF bulk) at each VDD/VSS pair, keep ADC traces short, and reserve the analog supply pin pair (AVDD/AVSS) for low-noise analog reference. For motor-control applications, use the dedicated PWM outputs and QEI interface rather than bit-banging to achieve deterministic switching behavior. This page synthesizes distributor pricing, parameter-verified drop-in alternatives, and practical design notes not consolidated in the manufacturer datasheet.

询价 联系我们
PIC32MK0256GPG048T-I/7MX - 32-Bit 120MHz MCU, 256KB Flash | Microchip
PIC32MK0256GPG048T-I/7MX

PIC32MK0256GPG048T-I/7MX - 32-Bit 120MHz MCU, 256KB Flash | Microchip

The Microchip Technology PIC32MK0256GPG048T-I/7MX is a 32-bit MIPS32 microAptiv PIC32MK microcontroller operating at 120 MHz with 256KB of Flash memory and 48-pin VQFN (6x6 mm) package. It belongs to the PIC32MK General Purpose (GPG) sub-family that combines high-performance 120 MHz processing with ECC-protected Flash and a rich peripheral set. The GPG variants are designed for general-purpose embedded designs while sharing the architecture with the motor-control (MCJ) family. A microcontroller (MCU) is a single-chip computer containing a CPU core, program memory (Flash), data memory (RAM), and integrated peripherals such as timers, ADCs, communication interfaces, and GPIO. 32-bit MCUs occupy the high-performance tier of the embedded hierarchy: microcontroller -> 32-bit MCU -> ARM/MIPS Cortex-class MCU -> application-specific MCU -> system-on-chip. The microAptiv core implements the MIPS32 instruction set and includes DSP extensions and a single-precision FPU on PIC32MK variants. Key features of this part include a 120 MHz CPU with 1.55 DMIPS/MHz performance, 256KB ECC-protected Flash, 32KB SRAM with parity, 12-bit 5 MSPS ADC, up to 6 UART/SPI/I2C channels, multiple PWM outputs suitable for motor control, and 5V-tolerant GPIO with 22 mA source/sink capability. The device supports industrial temperature range -40C to +85C (I-grades) and is offered in the compact 48-pin 6x6 mm VQFN package which suits space-constrained industrial designs. The PIC32MK0256GPG048T-I/7MX uses the MIPS32 microAptiv core with hardware multiply/divide and DSP ASE, paired with a 7-stage pipeline that delivers deterministic interrupt response. The integrated 12-bit ADC and dedicated motor-control PWM make the part a strong fit for mixed-signal applications, while the ECC Flash improves reliability in safety-sensitive industrial systems. The "NO CAN-FD" designation in distributor listings distinguishes this GPG variant from MCJ parts that include CAN-FD peripherals. Typical applications include industrial control boards, IIoT edge nodes, factory automation, BLDC motor control boards, and general-purpose 32-bit embedded platforms. The combination of 120 MHz performance and large Flash also supports protocol stacks such as Modbus, EtherNet/IP gateways, and graphical HMI interfaces. Designers should note the operating voltage range, decoupling requirements around the analog supply pins, and PCB thermal dissipation for the VQFN-48 exposed pad. Programming is supported by MPLAB X IDE with the XC32 compiler and the MPLAB Harmony framework for peripheral configuration. This page synthesizes verified distributor pricing, drop-in alternatives, and practical design notes not always consolidated on the manufacturer product page or distributor listings.

询价 联系我们
PIC32MK0256GPG064-E/PT - 32-bit 120MHz MCU, 256KB Flash | Microchip
PIC32MK0256GPG064-E/PT

PIC32MK0256GPG064-E/PT - 32-bit 120MHz MCU, 256KB Flash | Microchip

The Microchip Technology PIC32MK0256GPG064-E/PT is a 32-bit MIPS32 microAptiv PIC microcontroller running at up to 120 MHz, integrating 256 KB of ECC-protected Flash and 64 KB of SRAM in a 64-pin TQFP package. It belongs to the PIC32MK General Purpose (GP) sub-family, designed for motor control, industrial control, and Industrial Internet of Things (IIoT) applications where DSP-class math and high-resolution analog are required. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, non-volatile program memory (typically Flash), volatile working memory (SRAM), and a configurable set of peripherals such as timers, ADCs, communication controllers, and GPIO. The PIC32MK0256GPG064-E/PT sits in the hierarchy: 32-bit MCU -> MIPS32 microAptiv core -> PIC32MK family -> PIC32MK General Purpose (GP) sub-family -> semiconductor. Compared with 8-bit or 16-bit MCUs, a 32-bit core delivers higher MIPS per MHz, native DSP instructions, and larger linear address space, which matters when running motor-control loops, FOC algorithms, or TCP/IP stacks in real time. Key features include 256 KB Flash with error-correcting code (ECC) for Class B safety integrity, 64 KB SRAM, four independent 12-bit ADC pairs capable of 3.2 Msps aggregate conversion, four op-amps and three comparators in the analog front end, and a hardware CryptoEngine (the 'GPG' letter group indicates NO CAN-FD variant). The device supplies 6 UART, 4 SPI, 4 I2C, and USB 2.0 Full-Speed On-The-Go, plus 9 general-purpose 16-bit timers and 4 dedicated PWM generators with 8 outputs. Technically the PIC32MK0256GPG064-E/PT executes the MIPS32 microAptiv instruction set with DSP ASE, single-cycle hardware multiply-accumulate, and a 5-stage pipeline, achieving 1.52 DMIPS/MHz. The dual-rail analog architecture - one pair of 12-bit ADC rails plus dedicated op-amp/comparator analog resources - lets it close a single-shunt or three-shunt FOC loop without an external analog front-end IC, reducing BOM count for motor drives. Typical applications are BLDC/PMSM motor control, industrial automation PLCs, IIoT edge nodes, multi-channel sensor aggregation, and consumer appliances requiring UL/IEC 60730 Class B firmware self-test. The wide -40C to +125C operating range and ECC Flash suit the part to unattended industrial and appliance-class deployments. When designing with this MCU, reserve dedicated analog power and ground pins (AVDD/AVSS) and keep the 12-bit ADC traces short and guarded; ECC Flash does not eliminate read-disturb mitigation needs in long-lifecycle firmware. Pair with Microchip's MPLAB Harmony v3 for the motor-control or TCP/IP stacks and configure the CFGCON register's JTAG bit before first programming to free diagnostic pins. This page synthesizes 2026 distributor pricing, same-package drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone.

询价 联系我们
PIC32MK0256GPG064-E/R4X - 120MHz MCU 256KB Flash 64VQFN | Microchip
PIC32MK0256GPG064-E/R4X

PIC32MK0256GPG064-E/R4X - 120MHz MCU 256KB Flash 64VQFN | Microchip

The Microchip Technology PIC32MK0256GPG064-E/R4X is a 32-bit MIPS32 microAptiv PIC microcontroller operating at up to 120 MHz with 256 KB ECC-protected Flash and 64 KB SRAM, housed in a 64-pin VQFN (9x9 mm) package with 53 I/O. It operates from 2.3V to 3.6V across the industrial -40C to +125C temperature range and integrates a 12-bit ADC, 12-bit DAC, CAN-FD-capable peripherals, motor-control PWM, and rich connectivity for general-purpose and motion-control designs. A 32-bit microcontroller (MCU) is an integrated circuit combining a high-performance processor core, on-chip non-volatile program memory (Flash), volatile working memory (SRAM), and configurable peripherals on a single silicon die. MCUs form the compute tier between fixed-function ASICs and full microprocessors, executing embedded firmware for deterministic real-time tasks. Within the PIC32 family hierarchy, the microAptiv core delivers up to 1.53 DMIPS/MHz, and the GPG variant targets cost-optimized general-purpose applications as opposed to the motor-control MCJ/GPL subfamilies. Key differentiating features include 256 KB Flash with ECC and 64 KB SRAM with parity, 120 MHz maximum CPU clock (80 MHz on this specific GPG SKU), four I2C+SDA buses, two SPI/I2S interfaces, two UART modules, USB-FS device/host/OTG, a 12-bit 1.25 Msps ADC with up to 28 channels, and motor-control PWM capable of driving three-phase inverters. The ECC-protected Flash increases reliability in safety-conscious and outdoor-deployed systems where single-bit errors would otherwise escape detection. Hardware math accelerators (CPU with DSP-like instructions, FPU-ready on adjacent SKUs) ease real-time filter and control-loop workloads. The PIC32MK0256GPG064 silicon integrates a rich peripheral set: multiple general-purpose timers, a hardware crypto engine on selected variants, comparators, a charge-time-measurement unit (CTMU), and a real-time clock-calendar with backup registers. The 64-VQFN (9x9 mm) package includes an exposed pad that must be soldered to the ground plane for thermal dissipation and low-impedance return, supporting operation at the full industrial +125C junction temperature. Typical applications include motor control (BLDC/PMSM FOC drives), industrial IoT edge nodes, digital power conversion, building automation, multi-channel sensor fusion, and CAN-FD network nodes in vehicles and machinery. The combination of high CPU throughput, dual ADC capability, and CAN-FD positions this MCU as a versatile platform for both deterministic control loops and connected-device protocols. When designing with this MCU, allocate the ECC-protected Flash region for critical code, use the exposed pad of the VQFN-64 as the primary thermal path, and verify that 3.3V rails hold within ±5% under CPU peak load to avoid ADC reference drift. Use MPLAB X IDE with the XC32 compiler for firmware development. This page synthesizes verified distributor pricing, drop-in alternatives, and practical design notes drawn from the Microchip PIC32MK GPG/MCJ family datasheet - information not aggregated on any single distributor product page.

询价 联系我们
PIC32MK0256GPG064-I/PT - 120MHz MIPS32 256KB Flash MCU | Microchip
PIC32MK0256GPG064-I/PT

PIC32MK0256GPG064-I/PT - 120MHz MIPS32 256KB Flash MCU | Microchip

The Microchip Technology PIC32MK0256GPG064-I/PT is a 32-bit MIPS32 microAptiv MCU operating up to 120 MHz, integrating 256 KB of ECC-protected Flash and 64 KB of SRAM, housed in a 64-pin TQFP (10x10 mm) package. The part targets high-performance motor control, industrial automation, and multi-channel power-conversion designs, combining DSP-class throughput with a rich analog and communications peripheral set on a single die. An MCU (microcontroller unit) is a single-chip computer that integrates a CPU core, program and data memory, and programmable peripherals around one or more on-chip buses. The 32-bit class, exemplified by MIPS32 microAptiv and Arm Cortex-M cores, extends 16-bit PIC24/MCUs by adding higher clock rates, larger linear address space, hardware multiply-accumulate, and DSP instructions, placing PIC32MK at the boundary between classic microcontrollers and entry-level microprocessors. Within Microchip's portfolio PIC32MK sits above PIC32MX (lower analog content) and below PIC32MZ (with optional graphics/GPU and larger Flash), positioning it as the mid-range 32-bit family optimized for precision analog and motor-drive applications. The PIC32MK0256GPG064-I/PT specifically includes four analog op-amps usable as programmable-gain amplifiers, four 12-bit DAC outputs, and dual 12-bit ADCs with up to 30 analog inputs plus 3 MSPS capability, enabling simultaneous current and voltage sensing for FOC motor loops. Integrated peripherals include multiple UART, SPI, I2C, CAN-FD (depending on variant), SQI for external Flash, and a hardware crypto engine on selected SKUs. The 120 MHz core delivers 198 DMIPS and 3.06 CoreMark/MHz, allowing high-rate control loops without co-processor assistance. Typical uses are field-oriented control (FOC) of BLDC/PMSM motors, multi-phase digital power supplies, PLC analog front ends, industrial sensor hubs, and IIoT edge nodes with CAN-FD connectivity. The combination of ECC Flash, large RAM, and dual ADC sampling simplifies SIL-rated designs and ASIL-aware firmware development. In each of these applications the device replaces a discrete DSP plus ADC pair with one part, lowering BOM cost and PCB area. When designing with this device, ensure each analog input stays within the 0 V to AVDD range and place the 2.3 V-3.6 V supply decoupling within 5 mm of every VDD/VSS pin pair. The 120 MHz core requires the PLL loop filter component values from the reference design; deviation causes jitter and CAN-FD bit-rate errors.

询价 联系我们
PIC32MK0256GPG064-I/R4X - 32-Bit MCU 120MHz 256KB Flash | Microchip
PIC32MK0256GPG064-I/R4X

PIC32MK0256GPG064-I/R4X - 32-Bit MCU 120MHz 256KB Flash | Microchip

The Microchip Technology PIC32MK0256GPG064-I/R4X is a 32-bit MIPS32 microAptiv PIC32MK microcontroller IC operating at 120MHz with 256KB of Flash and 64KB of RAM, housed in a 64-pin VQFN (9x9 mm) package. It integrates a rich peripheral set targeting motor control, industrial control, and Industrial Internet of Things (IIoT) applications. Operating voltage range is 2.3V to 3.6V, supporting low-voltage embedded designs. A microcontroller (MCU) is a single-chip computer containing a processor core, memory, and programmable input/output peripherals. The PIC32MK family specifically combines a 32-bit MIPS32 microAptiv core with deterministic interrupt handling, hardware math accelerators, and motor-control-friendly peripherals such as high-resolution PWM and quadrature encoder interfaces, placing it in the hierarchical chain: MCU -> embedded controller -> real-time control IC -> semiconductor. Key features of the PIC32MK0256GPG064-I/R4X include 53 programmable I/O pins, CAN FD support for automotive-grade networking, multiple UART/SPI/I2C interfaces, 12-bit ADC modules with up to 3 MSPS sampling, and ECC-protected Flash memory for enhanced reliability in safety-critical applications. The 64-VQFN package provides a compact 9x9 mm footprint suitable for space-constrained PCB designs. Architecturally, the PIC32MK0256GPG064 uses a single-core MIPS32 microAptiv processor with hardware multiply/divide, branch prediction, and tightly-coupled memory. It also integrates dedicated motor-control PWM modules with edge-aligned and center-aligned modes, making it well-suited for field-oriented control (FOC) of three-phase BLDC and PMSM motors. Typical applications include industrial motor drives (BLDC, PMSM, ACIM), solar inverters, industrial automation PLCs, multi-channel data acquisition systems, and CAN-FD-enabled automotive ECUs. The combination of high-performance 32-bit processing with motor-control peripherals makes it ideal for real-time closed-loop control applications. When designing with this device, ensure adequate decoupling on the VDD pins (typically 100nF ceramic per pin plus bulk capacitance) and follow Microchip's layout guidelines for the VQFN exposed pad, which must be soldered to the ground plane for proper thermal dissipation. Pay attention to the 2.3V-3.6V supply range when interfacing with 5V peripherals. This page synthesizes distributor pricing, drop-in alternatives from the PIC32MK family, and practical design notes not found in the manufacturer datasheet alone, providing a single-source reference for engineers evaluating this MCU.

询价 联系我们
PIC32MK0256GPG064T-E/PT - 256KB Flash 120MHz MCU | Microchip
PIC32MK0256GPG064T-E/PT

PIC32MK0256GPG064T-E/PT - 256KB Flash 120MHz MCU | Microchip

The Microchip Technology PIC32MK0256GPG064T-E/PT is a 32-bit MIPS32 microAptiv PIC32MK microcontroller operating at up to 80MHz, with 256KB of ECC-protected Flash memory and 64KB of SRAM, housed in a 64-pin TQFP (PT) package measuring 10x10 mm. The device integrates a rich peripheral set including CAN-FD, USB, 12-bit ADC, op-amps, and DSP-grade motor-control PWMs targeting industrial and IIoT designs. Per Microchip product documentation, the PIC32MK family combines 32-bit 120MHz-class performance with up to 1MB of ECC Flash and dual CAN-FD interfaces. A 32-bit microcontroller (MCU) is a single-chip processor that integrates a CPU core, program and data memory, and configurable peripherals on one die. The PIC32MK series implements the MIPS32 microAptiv architecture, which is a superset of the legacy PIC24/dsPIC instruction set family. Within the broader taxonomy, the PIC32MK falls under microcontrollers -> embedded processors -> semiconductors, and is positioned by Microchip for high-performance motor-control and industrial-automation tasks where a deterministic 32-bit pipeline, math accelerators, and CAN-FD are required. Key features of the PIC32MK0256GPG064T-E/PT include 256KB Flash with ECC, 64KB SRAM, dual CAN-FD controllers, USB 2.0 Full-Speed, multiple SPI/I2C/UART interfaces, 12-bit ADCs with up to 3.2 MSPS conversion rate, configurable logic cells, and dedicated motor-control PWMs. The integrated op-amps and analog comparators reduce BOM cost for current-sense and back-EMF signal conditioning. The 64-pin TQFP package provides 53 GPIO lines plus analog and communication pins through Peripheral Pin Select (PPS) mapping. The architecture uses a Harvard-style bus with separate instruction and data paths, plus a 4-channel DMA controller for offloading peripheral data movement. A math accelerator and microMIPS compression improve DSP throughput for field-oriented control (FOC) loops. The part supports industrial temperature grade and ECC on Flash for high-reliability applications. Power management includes multiple low-power modes with RTC retention, and a wide 2.3V to 3.6V supply range with internal LDO regulation for the core. Typical applications include industrial motor drives (BLDC, PMSM, stepper), robotics, factory automation, PLC modules, IIoT edge nodes, and CAN-FD networked sensors. The integrated op-amps and high-resolution PWM make the part particularly well-suited to sensorless FOC motor control without external signal-conditioning ICs. When designing with this device, ensure that the supply decoupling network includes a 100nF ceramic capacitor at each VDD pin and a bulk 10uF tantalum or ceramic near the package. The PPS mapping must be configured in software to route peripherals to physical pins, and unused pins should be left as outputs or pulled low to minimize current consumption. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet, providing a consolidated engineering reference for sourcing and applying the PIC32MK0256GPG064T-E/PT.

询价 联系我们
PIC32MK0256GPG064T-I/R4X - 32-bit 120MHz MCU, 256KB Flash, 64-VQFN | Microchip
PIC32MK0256GPG064T-I/R4X

PIC32MK0256GPG064T-I/R4X - 32-bit 120MHz MCU, 256KB Flash, 64-VQFN | Microchip

The Microchip Technology PIC32MK0256GPG064T-I/R4X is a high-performance 32-bit microcontroller based on the MIPS32 microAptiv core, delivering up to 120 MHz of processing performance with 256 KB of ECC-protected Flash memory and 64 KB of SRAM, housed in a 64-pin VQFN (9x9 mm) package. The 'T' suffix indicates tape-and-reel packaging and the 'I' suffix indicates the industrial temperature grade of -40C to +85C, while the GPG descriptor identifies this as the General Purpose variant (no CAN-FD peripheral) of the PIC32MK family. What is a 32-bit MCU? A 32-bit microcontroller is an integrated circuit that contains a 32-bit processor core, program memory (typically Flash), data memory (SRAM), and a rich set of peripherals such as timers, communication interfaces, and analog-to-digital converters on a single silicon die. The PIC32MK family sits within the broader PIC32 family of microcontrollers, which itself belongs to the microcontroller hierarchy: microcontroller -> embedded processor -> semiconductor -> integrated circuit. The microAptiv core implements the MIPS32 instruction set with DSP and FPU extensions, giving the PIC32MK class-leading signal-processing throughput for motor-control and power-conversion loops. Key features of the PIC32MK0256GPG064T-I/R4X include 256 KB of ECC-protected Flash, 64 KB of SRAM, four 16-bit timers, multiple UART/SPI/I2C interfaces, a 12-bit ADC with up to 42 channels and 3 MSPS, multiple DAC outputs, motor-control PWMs, and an operating voltage range of 2.3 V to 3.6 V. The on-chip FPU and DSP engine accelerate single-precision floating-point and MAC-intensive loops, while ECC on Flash and SRAM improves reliability in industrial environments. Typical applications include industrial motor control (BLDC, PMSM, FOC), industrial automation and PLC modules, multi-channel sensor fusion, general-purpose DSP-accelerated embedded systems, LED lighting controllers, power-conversion digital control loops, and IIoT edge nodes. The 64-VQFN (9x9 mm) footprint and industrial temperature grade make it suitable for compact, thermally-constrained industrial designs. When designing with this part, ensure the 64-VQFN exposed pad is soldered to a sufficient copper pour to meet the thermal resistance specification. Decouple VDD with low-ESR 100 nF ceramic capacitors placed within 5 mm of each supply pin per the manufacturer datasheet recommendation.

询价 联系我们
PIC32MK0256MCJ048-E/7MX - 120MHz 32-bit MCU, 256KB Flash | Microchip
PIC32MK0256MCJ048-E/7MX

PIC32MK0256MCJ048-E/7MX - 120MHz 32-bit MCU, 256KB Flash | Microchip

The Microchip Technology PIC32MK0256MCJ048-E/7MX is a 120 MHz 32-bit MIPS32 microAptiv MCU with 256 KB ECC-protected Flash and 64 KB SRAM, housed in a 48-pin VQFN (7MX, 6x6 mm) package with automotive AEC-Q100 grade. It is part of the PIC32MK family and targets motor control, industrial control, and Industrial IoT applications. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, memory, and programmable peripherals. The PIC32MK family uses a MIPS32 microAptiv core which combines deterministic interrupt response with DSP extensions and a memory protection unit. Within the broader hierarchy, an MCU is a subset of microprocessors, sits inside the semiconductor category, and is a fundamental building block of any embedded system. This positions the PIC32MK family between 8-bit PIC16/PIC24 devices and 32-bit Cortex-M4 competitors, providing higher computational headroom while retaining the PIC ecosystem. Key features include up to 120 MHz CPU speed, 4 dedicated PWM channels with 7.5 ns resolution for advanced motor control, multiple CAN-FD modules for industrial networking, ECC on Flash for safety-critical code, a 12-bit ADC at 3.75 Msps, and a USB 2.0 Full-Speed OTG controller. The peripheral set also includes multiple UART, SPI, I2C, and quadrature encoder interfaces that simplify closed-loop motor control designs. Internal voltage regulation and brown-out detection support robust operation across 2.3V to 3.6V. The device integrates a high-performance timer/counter architecture optimized for field-oriented control (FOC) of PMSM, BLDC, and stepper motors. Hardware-based fault handling and dead-band generation reduce CPU load, allowing the 120 MHz core to focus on application-level logic. A 32-bit core coupled with deterministic DMA channels supports parallel data acquisition without CPU intervention. Typical applications include 3-phase motor drives for industrial pumps and fans, IIoT sensor hubs with CAN-FD backbones, automotive body controllers, digital power converters, and precision servo amplifiers. The -E temperature grade (-40C to +125C) and AEC-Q100 qualification allow deployment under hood and in industrial cabinets. When designing with this MCU, ensure decoupling is placed within 5 mm of each VDD pin pair and that the exposed pad is soldered to a continuous ground plane for thermal dissipation. For motor control, route analog and digital grounds as separate nets that join at a single point near the IC. This page synthesizes distributor pricing from DigiKey, Mouser, and Octopart, drop-in same-package alternatives from the PIC32MK family, and design considerations not collated on any single manufacturer or distributor page.

询价 联系我们
PIC32MK0256MCJ048-E/Y8X - 80MHz 32-bit MCU, 256KB Flash, CAN-FD | Microchip
PIC32MK0256MCJ048-E/Y8X

PIC32MK0256MCJ048-E/Y8X - 80MHz 32-bit MCU, 256KB Flash, CAN-FD | Microchip

The Microchip Technology PIC32MK0256MCJ048-E/Y8X is a 32-bit MIPS32 microAptiv PIC microcontroller running at up to 80 MHz (CPU core family maximum 120 MHz per Microchip's PIC32MK family specification), integrating 256 KB of ECC-protected Flash program memory and 64 KB of SRAM, all housed in a 48-pin TQFP (7x7 mm) package. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (Flash), data memory (RAM), and a rich set of peripherals onto one die. Within the semiconductor taxonomy, the PIC32MK sits as: microcontroller -> embedded processor -> 32-bit MCU -> motor-control/IIoT class. The "MC" in the part number designates the motor-control variant, while "J048" indicates 256 KB Flash / 64 KB RAM in a 48-pin TQFP. The "-E" suffix designates the -40C to +125C extended operating-temperature grade, and "Y8X" denotes 48-pin TQFP with tape-and-reel packaging. Key features include 12-bit ADC with up to 18 analog inputs, 6 PWM channels suitable for 3-phase motor drive, 5 analog comparators, 11 timers, 8 DMA channels, CAN-FD, two I2C, two I2S, SPI, and two UART interfaces. The device also integrates ECC-protected Flash for high-reliability operation in industrial environments. The PIC32MK silicon combines a deterministic MIPS32 microAptiv core with a hardware math accelerator and dual-bank Flash, enabling live firmware updates without CPU stall. Dedicated motor-control peripherals (high-resolution PWM, quadrature encoder interface, analog comparators with DAC references) allow sensorless or sensored FOC / six-step BLDC drive on the same chip, reducing BOM and PCB area. Typical applications include field-oriented control (FOC) motor drives for BLDC/PMSM, industrial PLC modules, IIoT edge nodes with CAN-FD, multi-channel analog data acquisition, and digital power conversion. Its extended-temperature operation makes it suitable for factory-floor and automotive under-hood subsystems. When designing with this part, ensure the CAN-FD transceiver is rated for the bus topology and that the 3.3V supply is decoupled with at least 100 nF + 10 uF ceramic capacitance placed within 100 mm of the VDD pins per the Microchip PIC32MK family datasheet DS60001570D. This page synthesizes distributor pricing, same-family drop-in alternatives, and practical design notes not found on the manufacturer product page alone.

询价 联系我们