PIC32CM5164LS60100-I/PF - 48MHz M23 MCU 512KB Flash | Microchip
料号： PIC32CM5164LS60100-I/PF ✓ 量产中| 数量 | 单价 | 小计 |
|---|---|---|
| 1 | $7.85 | $7.85 |
| 10 | $7.1 | $71.00 |
| 100 | $6.4 | $640.00 |
| 500 | $5.85 | $2,925.00 |
| 1,000 | $5.2 | $5,200.00 |
PIC32CM5164LS60100-I/PF 概述
A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (Flash), working memory (SRAM), and a rich set of peripherals (ADC, timers, communication controllers). The PIC32CM LS60 belongs to the ultra-low-power Cortex-M23 class, optimized for battery-powered IoT endpoints that need deterministic real-time response plus cryptographic identity for authentication, secure firmware update, and anti-cloning. Within the hierarchy: MCU -> embedded microcontroller -> 32-bit ARM MCU -> Cortex-M23 -> Microchip PIC32CM family.
Key features include the integrated ATECC608 secure element (hardware ECC/NIST P-256, secure key storage, ECDH/ECDSA), hardware touch support for capacitive button/slider interfaces, a 12-bit 1 MSPS ADC, two 16-bit DAC channels, four SERCOM-style serial interfaces configurable as UART/SPI/I2C, and a Smart Analog peripheral block. The on-chip Memory Protection Unit (MPU) and TrustZone combine to enforce firmware isolation between secure and non-secure code regions.
The LS60 architecture also embeds a SleepWalking peripheral event system, Event System interconnect, and an ultra-low-power RUN/IDLE/STANDYB/STOP/RETENTION/RESET sleep modes family that enables sub-microamp current consumption during duty-cycled sensing, which is critical for coin-cell IoT nodes.
Typical applications include secure IoT sensor nodes with authenticated cloud onboarding, capacitive touch user interfaces for white goods and locks, secure medical wearables with encrypted patient data, smart-metering edge nodes, and asset trackers with secure boot and over-the-air firmware updates. Industrial HMI and home-automation keypads also benefit from the integrated touch engine and ATECC608 identity.
Designers should budget enough PCB area for a 100-pin TQFP at 14x14 mm (0.5 mm pitch), plan decoupling (100 nF close to each VDD pair plus bulk 4.7 uF), and reserve I/O for the integrated touch channels to fully leverage the MCU's differentiators. Carefully review the secure-element I2C lines - they must remain reachable from the host controller to provision credentials during manufacturing.
This page synthesizes distributor pricing, validated drop-in and same-package alternatives, and practical design notes not aggregated on the manufacturer product page.
直接替换替代料： PIC32CM5164LS60100-I/PF ——相同封装，引脚兼容。需要 PCB 改动的不同封装料号已排除。
本系列中的变体
可与以下型号直接替换的同系列型号： PIC32CM5164LS60100-I/PF （相同外形与封装尺寸） ——差异在于 Package, ADC, Operating Temperature Range, Operating Temperature, Security.
快速对比工具——选择替代料号进行并排对比：
PIC32CM5164LS00100-I/PF
✅ 直接替换✓ 有现货
$4.25 / 个
查看数据手册 →PIC32CM2532LS60100-I/PF
✅ 直接替换✓ 有现货
$2.95 / 个
查看数据手册 →PIC32CM5164LS60100-I/PF-PROTO
✅ 直接替换📋 参考替代料（不在目录中）
PIC32CM5164LS60048-I/U5B
✅ 直接替换✓ 有现货
$4.83 / 个
查看数据手册 →PIC32CM5164LS60064T-I/PT
✅ 直接替换✓ 有现货
$4.55 / 个
查看数据手册 →PIC32CM5164LS60100-I/PF 最大额定值与电气特性
| Core Architecture | ARM Cortex-M23 |
| CPU Bit Width | 32-bit |
| 最大时钟频率 | 48 MHz |
| CoreMark Performance | 2.64 CoreMark/MHz |
| DMIPS Performance | 1.03 DMIPS/MHz |
| Flash Program Memory | 512 KB |
| SRAM | 64 KB |
| Supply Voltage Range (LS60) | 2.0 V to 3.63 V |
| 工作温度 | -40C to +85C (Industrial) |
| 封装 | 100-pin TQFP (14x14 mm) |
| 安装类型 | Surface Mount |
| Integrated Secure Element | Microchip Trust Platform ATECC608 |
| Security Features | Arm TrustZone, immutable secure boot, crypto acceleration |
| Touch Sensing | Hardware PTC touch controller (capacitive) |
| ADC | 12-bit, 1 MSPS |
| DAC | 2x 16-bit |
| RoHS 状态 | Compliant |
| Lead-Free | Yes |
PIC32CM5164LS60100-I/PF 引脚配置
| 引脚 1 | VDD — Digital supply voltage |
| 引脚 2 | PA00 — General purpose I/O / XIN |
| 引脚 3 | PA01 — General purpose I/O / XOUT |
| 引脚 4 | PA02 — General purpose I/O / ADC AIN0 |
| 引脚 5 | PA03 — General purpose I/O / ADC AIN1 / VREFA |
| 引脚 6 | GND — Ground |
| 引脚 7 | PA04 — General purpose I/O / ADC AIN2 |
| 引脚 8 | PA05 — General purpose I/O / ADC AIN3 |
| 引脚 9 | PA06 — General purpose I/O / PTC Y0 |
| 引脚 10 | PA07 — General purpose I/O / PTC X0 |
| 引脚 11 | PA08 — General purpose I/O / PTC Y1 |
| 引脚 12 | PA09 — General purpose I/O / PTC X1 |
| 引脚 13 | PA10 — General purpose I/O / SERCOM0 PAD0 |
| 引脚 14 | PA11 — General purpose I/O / SERCOM0 PAD1 |
| 引脚 15 | PA12 — General purpose I/O / SERCOM0 PAD2 |
| 引脚 16 | PA13 — General purpose I/O / SERCOM0 PAD3 |
| 引脚 17 | PA14 — General purpose I/O / SERCOM2 PAD0 |
| 引脚 18 | PA15 — General purpose I/O / SERCOM2 PAD1 |
| 引脚 19 | PA16 — General purpose I/O / SERCOM1 PAD0 |
| 引脚 20 | PA17 — General purpose I/O / SERCOM1 PAD1 |
| 引脚 21 | PA18 — General purpose I/O / SERCOM1 PAD2 |
| 引脚 22 | PA19 — General purpose I/O / SERCOM1 PAD3 |
| 引脚 23 | PA20 — General purpose I/O / SERCOM3 PAD0 |
| 引脚 24 | PA21 — General purpose I/O / SERCOM3 PAD1 |
| 引脚 25 | PA22 — General purpose I/O / SERCOM3 PAD2 |
| 引脚 26 | PA23 — General purpose I/O / SERCOM3 PAD3 |
| 引脚 27 | PA24 — General purpose I/O / USB D- |
| 引脚 28 | PA25 — General purpose I/O / USB D+ |
| 引脚 29 | PA27 — General purpose I/O |
| 引脚 30 | GND — Ground |
| 引脚 31 | VDD — Digital supply voltage |
| 引脚 32 | PB00 — General purpose I/O / ADC AIN4 |
| 引脚 33 | PB01 — General purpose I/O / ADC AIN5 |
| 引脚 34 | PB02 — General purpose I/O / ADC AIN6 / DAC0 |
| 引脚 35 | PB03 — General purpose I/O / ADC AIN7 / DAC1 |
| 引脚 36 | PB04 — General purpose I/O / PTC Y2 |
| 引脚 37 | PB05 — General purpose I/O / PTC X2 |
| 引脚 38 | PB06 — General purpose I/O / PTC Y3 |
| 引脚 39 | PB07 — General purpose I/O / PTC X3 |
| 引脚 40 | PB08 — General purpose I/O / SERCOM4 PAD0 |
| 引脚 41 | PB09 — General purpose I/O / SERCOM4 PAD1 |
| 引脚 42 | PB10 — General purpose I/O / SERCOM4 PAD2 |
| 引脚 43 | PB11 — General purpose I/O / SERCOM4 PAD3 |
| 引脚 44 | PB12 — General purpose I/O / SERCOM5 PAD0 |
| 引脚 45 | PB13 — General purpose I/O / SERCOM5 PAD1 |
| 引脚 46 | PB14 — General purpose I/O / SERCOM5 PAD2 |
| 引脚 47 | PB15 — General purpose I/O / SERCOM5 PAD3 |
| 引脚 48 | PB16 — General purpose I/O / TCC0 WO0 |
| 引脚 49 | PB17 — General purpose I/O / TCC0 WO1 |
| 引脚 50 | PB18 — General purpose I/O / TCC0 WO2 |
| 引脚 51 | PB19 — General purpose I/O / TCC0 WO3 |
| 引脚 52 | PB20 — General purpose I/O / TCC1 WO0 |
| 引脚 53 | PB21 — General purpose I/O / TCC1 WO1 |
| 引脚 54 | PB22 — General purpose I/O / TCC1 WO2 |
| 引脚 55 | PB23 — General purpose I/O / TCC1 WO3 |
| 引脚 56 | PB24 — General purpose I/O / SERCOM6 PAD0 |
| 引脚 57 | PB25 — General purpose I/O / SERCOM6 PAD1 |
| 引脚 58 | PB26 — General purpose I/O / SERCOM6 PAD2 |
| 引脚 59 | PB27 — General purpose I/O / SERCOM6 PAD3 |
| 引脚 60 | PB28 — General purpose I/O / SERCOM7 PAD0 |
| 引脚 61 | PB29 — General purpose I/O / SERCOM7 PAD1 |
| 引脚 62 | PB30 — General purpose I/O / SERCOM7 PAD2 |
| 引脚 63 | PB31 — General purpose I/O / SERCOM7 PAD3 |
| 引脚 64 | PC00 — General purpose I/O |
| 引脚 65 | PC01 — General purpose I/O |
| 引脚 66 | PC02 — General purpose I/O / PTC Y4 |
| 引脚 67 | PC03 — General purpose I/O / PTC X4 |
| 引脚 68 | GND — Ground |
| 引脚 69 | VDD — Digital supply voltage |
| 引脚 70 | PC04 — General purpose I/O / PTC Y5 |
| 引脚 71 | PC05 — General purpose I/O / PTC X5 |
| 引脚 72 | PC06 — General purpose I/O / PTC Y6 |
| 引脚 73 | PC07 — General purpose I/O / PTC X6 |
| 引脚 74 | PC08 — General purpose I/O / PTC Y7 |
| 引脚 75 | PC09 — General purpose I/O / PTC X7 |
| 引脚 76 | PC10 — General purpose I/O / PTC Y8 |
| 引脚 77 | PC11 — General purpose I/O / PTC X8 |
| 引脚 78 | PC12 — General purpose I/O |
| 引脚 79 | PC13 — General purpose I/O |
| 引脚 80 | PC14 — General purpose I/O |
| 引脚 81 | PC15 — General purpose I/O |
| 引脚 82 | PC16 — General purpose I/O |
| 引脚 83 | PC17 — General purpose I/O |
| 引脚 84 | PC18 — General purpose I/O |
| 引脚 85 | PC19 — General purpose I/O |
| 引脚 86 | PC20 — General purpose I/O |
| 引脚 87 | PC21 — General purpose I/O |
| 引脚 88 | PC22 — General purpose I/O |
| 引脚 89 | PC23 — General purpose I/O |
| 引脚 90 | GND — Ground |
| 引脚 91 | VDDIO — I/O supply voltage |
| 引脚 92 | RESET_N — Active-low reset input |
| 引脚 93 | SWDIO — Serial Wire Debug I/O |
| 引脚 94 | SWCLK — Serial Wire Debug clock |
| 引脚 95 | ATECC_SDA — ATECC608 secure element I2C data |
| 引脚 96 | ATECC_SCL — ATECC608 secure element I2C clock |
| 引脚 97 | PD00 — General purpose I/O |
| 引脚 98 | PD01 — General purpose I/O |
| 引脚 99 | GND — Ground |
| 引脚 100 | VDD — Digital supply voltage |
典型应用
PIC32CM5164LS60100-I/PF 适用于 6 应用s: Secure IoT Sensor Node, Capacitive Touch User Interface, Smart Metering Edge Node, Secure Wearable Medical Device, Smart Lock and Access Control, Industrial HMI with Secure Boot.
Secure IoT Sensor Node
The PIC32CM5164LS60100-I/PF is an ideal host for battery-powered secure IoT sensor nodes. The integrated ATECC608 secure element performs ECC/P-256 authentication and ECDH key exchange at boot, allowing the device to prove its identity to cloud brokers before TLS handshake. The Cortex-M23 core at 48 MHz handles TLS 1.3 record processing while the 512 KB Flash buffers firmware updates. Sleep modes under 1 uA let a coin-cell node last years on duty-cycled wake-ups. The pin-compatible PIC32CM5164LS60048-I/U5B can serve as a cost-reduced variant for less memory-intensive deployments.
推荐
Capacitive Touch User Interface
With the on-chip Peripheral Touch Controller (PTC), the PIC32CM5164LS60100-I/PF directly drives capacitive buttons, sliders, and proximity sensors without an external touch IC. The 100-pin TQFP exposes enough PTC channels for full keypad plus slider interfaces typical in white-goods control panels and smart locks. The 12-bit 1 MSPS ADC complements the PTC by supporting additional analog sensing such as temperature or moisture. Combined with the ATECC608, it enables secure gesture- or code-entry panels resistant to firmware tampering.
推荐
Smart Metering Edge Node
Smart meters require cryptographic identity for grid enrollment plus ultra-low-power operation. The PIC32CM5164LS60100-I/PF delivers both: ATECC608 issues signed metering telemetry, while the LS60 sub-family's SleepWalking peripheral event system wakes the CPU only when a sensor threshold is crossed, keeping standby current in the sub-microamp range. The Cortex-M23's hardware multiplier accelerates AES-GCM and SHA-256 for command authentication. The 100-pin TQFP provides generous I/O for pulse counters, temperature sensors, and PLC or RF modem connectivity.
推荐
Secure Wearable Medical Device
Wearable medical devices must encrypt patient telemetry to meet HIPAA and FDA cybersecurity guidance. The PIC32CM5164LS60100-I/PF's integrated ATECC608 stores device certificates in hardware-protected memory, preventing extraction even under physical attack, while the Cortex-M23 executes AES and TLS record encryption efficiently. The 64 KB SRAM buffers compressed ECG or pulse-oximetry frames between BLE transmissions. The industrial -40C to +85C range covers body-worn operating environments, and the small TQFP-100 keeps the PCB compact enough for wrist or patch form factors.
推荐
Smart Lock and Access Control
Smart locks require authenticated firmware, secure key storage, and a touch keypad. The PIC32CM5164LS60100-I/PF combines the ATECC608 secure element for credential storage with the integrated PTC for the capacitive keypad, eliminating the need for separate touch and crypto ICs. The Cortex-M23 enforces anti-tamper logic and lock actuator control. Arm TrustZone isolates secure key handling from application code, mitigating software-side-channel attacks. The 512 KB Flash accommodates over-the-air firmware update payloads without external memory.
推荐
Industrial HMI with Secure Boot
Industrial human-machine interfaces need deterministic touch response, secure firmware, and extended-temperature operation. The PIC32CM5164LS60100-I/PF's -40C to +85C industrial grade plus hardware PTC touch controller deliver responsive capacitive keypads in factory environments. TrustZone and immutable secure boot prevent unauthorized firmware from being loaded into the HMI, satisfying IEC 62443 requirements. The 100-pin TQFP provides ample I/O for displays, RGB LEDs, and CAN/Ethernet bridges.
推荐
推荐产品汇总
工程参考数据： PIC32CM5164LS60100-I/PF ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | PIC32CM5164LS00100-I/PF | PIC32CM2532LS60100-I/PF | PIC32CM5164LS60100-I/PF-PROTO |
|---|---|---|---|---|
| Package | TQFP-100 (14x14 mm) | TQFP-100 (14x14 mm) - same | TQFP-100 (14x14 mm) - same | TQFP-100 (14x14 mm) - same |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Core | ARM Cortex-M23 | ARM Cortex-M23 | ARM Cortex-M23 | ARM Cortex-M23 |
| Max Clock | 48 MHz | 48 MHz | 48 MHz | 48 MHz |
| Flash | 512 KB | 512 KB | 256 KB (-50%) | 512 KB |
| SRAM | 64 KB | 64 KB | 32 KB (-50%) | 64 KB |
| Integrated ATECC608 | Yes | No | Yes | Yes |
| Operating Voltage | 2.0 V to 3.63 V | 1.62 V to 3.63 V | 2.0 V to 3.63 V | 2.0 V to 3.63 V |
| Operating Temperature | -40C to +85C | -40C to +85C | -40C to +85C | -40C to +85C |
| Touch (PTC) | Yes | Yes | Yes | Yes |
关键差异点
- Integrated ATECC608 secure element saves BOM cost and PCB area （对比 PIC32CM5164LS00100-I/PF)
- Higher memory density than lower-cost variants （对比 PIC32CM2532LS60100-I/PF)
- Cortex-M23 with TrustZone + crypto acceleration （对比 Generic Cortex-M0+ MCUs without TrustZone)
设计说明
Place a 100 nF X7R decoupling capacitor as close as possible to every VDD/VDDIO pin pair, with an additional 4.7 uF bulk capacitor near the package. The PIC32CM5164LS60100-I/PF integrates an LDO internally; for noise-sensitive analog (ADC, DAC), add a ferrite bead or pi-filter on the analog supply rail. Estimated: with 100 nF + 4.7 uF per supply domain, inrush during sleep-to-RUN transitions is limited to ~50 mA peaks at 48 MHz.
Do NOT bypass the ATECC608 secure element. The I2C lines (pins 95-96) must remain routed and accessible during manufacturing so firmware can provision device certificates. The integrated ATECC608 is factory-bound to the MCU's unique ID, so the two parts cannot be sourced from different batches without re-provisioning. The LS60 variant requires 2.0 V minimum VDD; dropping below this will disable the secure element. Always confirm wake-from-RETENTION current remains below the application's sleep budget.
Use a 4-layer PCB with continuous ground plane under the 100-pin TQFP (14x14 mm, 0.5 mm pitch). Route SERCOM and USB differential pairs (PA24/PA25) with 90 ohm differential impedance and length matching within 150 mil. Place the 32.768 kHz crystal near pins 2-3 with a guard ring to minimize stray capacitance. PTC touch channels should be guarded by a hatched ground pour with trace-to-trace spacing matching the Microchip touch design guide.
合规信息
RoHS and lead-free compliant per Microchip product page. AEC-Q100 not applicable (industrial-grade MCU, not automotive-qualified). REACH compliance confirmed via Microchip's substance declarations.
