集成电路

子分类

📁 ADC/DAC 2,700+ 产品 📁 放大器IC 1,100+ 产品 📁 音频编解码器 18 产品 📁 音频IC 2 产品 📁 时钟与计时 480+ 产品 📁 Comparator ICs 0 产品 📁 DSP 1,000+ 产品 📁 数据采集IC 2 产品 📁 数字电位器 4 产品 📁 显示驱动与控制器 1 产品 📁 FPGA与CPLD 6,800+ 产品 📁 接口IC 2,300+ 产品 📁 LED驱动器 1 产品 📁 逻辑IC 360+ 产品 📁 存储IC 870+ 产品 📁 微控制器 19,000+ 产品 📁 微处理器 4 产品 📁 电机驱动器 1 产品 📁 其他 1 产品 📁 Sensor and Detector Interfaces 1 产品 📁 专用IC 15 产品 📁 视频IC 13 产品

产品（35,000+)

TS941ID - 2.5-10V Rail-to-Rail Op Amp | STMicroelectronics
TS941ID

TS941ID - 2.5-10V Rail-to-Rail Op Amp | STMicroelectronics

STMicroelectronics TS941ID is a single-circuit, general-purpose operational amplifier featuring a rail-to-rail output, 2.5 V to 10 V supply operation, and an 8-pin SOIC package. The device belongs to the TS94x micropower operational-amplifier family and is designed for instrumentation, signal buffering, and other low-voltage analog signal-chain applications. Its low-noise operation, high input impedance, and approximately 1 pA input-bias current support accurate handling of high-impedance sources while its rail-to-rail output improves dynamic range near the positive and negative supply rails. An operational amplifier, or op amp, is a high-gain differential amplifier used to amplify, buffer, compare, and filter analog signals. The TS941ID sits within the operational-amplifier hierarchy and operates from a 2.5 V to 10 V supply, making it suitable for battery-powered, industrial-control, test-and-measurement, and portable equipment. Its rail-to-rail output stage allows the output voltage to approach the supply limits more closely than a conventional output stage, although the exact output swing and input common-mode behavior must be checked in the manufacturer datasheet for the selected supply voltage. Key features include a single amplifier configuration, rail-to-rail output, low-noise operation, high input impedance, and very low input-bias current of approximately 1 pA. The 2.5 V minimum supply voltage supports compact, low-energy systems, while the 10 V maximum provides compatibility with common industrial and laboratory supply rails. The manufacturer specifies operation over -40 °C to +85 °C, covering industrial temperature requirements without requiring an automotive-qualified variant. The TS941ID is intended for general-purpose precision signal conditioning rather than as a high-speed communications amplifier. Its micropower-oriented design is valuable when battery current is important, but the precise quiescent-current value should be taken from the manufacturer datasheet. The approximately 1 pA input-bias current is particularly useful with high-impedance sensors because it limits the DC current drawn through the source resistance and helps reduce input-offset errors. Typical applications include sensor-signal conditioning, low-current transimpedance buffering, portable instrumentation, industrial measurement, and general analog signal conditioning. In a transimpedance stage, the TS941ID can be paired with a suitable feedback resistor and compensation capacitor while its low input-bias current reduces bias-current-induced error. In instrumentation, it can buffer inputs before a higher-precision converter or provide gain around sensors whose output range does not use the complete supply span. When designing around the TS941ID, verify input common-mode range, output swing, unity-gain stability, noise, slew rate, and quiescent current against the actual load and supply conditions. Place input, feedback, and decoupling connections for low noise and stable feedback operation, and include adequate output-current margin for capacitive or resistive loads. The 8-pin SOIC footprint is convenient for conventional surface-mount assembly but is not as compact as the smallest QFN packages. This product page consolidates the verified manufacturer information, distributor availability references, family-level alternatives, parameter comparisons, and practical design guidance. It distinguishes confirmed TS941ID data from specifications that still require confirmation from the manufacturer datasheet, helping engineers identify the part faster without presenting unverified values as established facts.

USD $0.82 有现货
TS944IPT - Quad Rail-to-Rail 1.2µA Op-Amp | STMicroelectronics
TS944IPT

TS944IPT - Quad Rail-to-Rail 1.2µA Op-Amp | STMicroelectronics

The STMicroelectronics TS944IPT is a quad CMOS-input operational amplifier delivering rail-to-rail output swing while consuming only 1.2 µA typical quiescent current per channel, packaged in a 14-pin TSSOP (Tape & Reel). It operates from a single 2.5 V to 10 V supply over the -40 °C to +85 °C industrial temperature range and provides a gain-bandwidth product of 10 kHz, making it ideal for ultra-low-power signal conditioning. An operational amplifier (op-amp) is a high-gain DC-coupled differential amplifier that uses external feedback components to set closed-loop gain, bandwidth, and transfer function. The TS944 belongs to the micropower CMOS op-amp family — a class of linear ICs that prioritize nano- to micro-amp quiescent current draw for battery-powered and energy-harvesting designs. Within the broader semiconductor hierarchy, it sits under: op-amp -> amplifier -> analog IC -> linear IC -> integrated circuit. Key features include four independent op-amp channels in one package, CMOS inputs delivering ultra-low input bias current, rail-to-rail output swing that maximizes dynamic range on low-voltage supplies, and 1.2 µA typical supply current per amplifier that enables years of runtime from small cells. The device is unity-gain stable and supports single-supply operation from 2.5 V to 10 V, simplifying designs that previously needed bipolar ±5 V rails. The TS944 architecture uses a CMOS input stage that achieves very low bias current while the class-AB output stage swings to within millivolts of both supply rails. This combination eliminates the need for input bias-current compensation in high-impedance sensor interfaces and lets designers operate the part directly from a single lithium cell or 3.3 V digital rail without sacrificing headroom. Typical applications include battery-powered sensor signal conditioning, portable medical monitors, IoT edge nodes, active filters, transducer pre-amplifiers, and any micropower analog front end where four amplifiers must fit in a small 14-pin TSSOP footprint. Designers should bypass supplies with 100 nF ceramic capacitors placed within 5 mm of VCC and avoid capacitive loads above 1 nF without an isolation resistor to prevent oscillation.

询价 联系我们
TS951ID - 3MHz Rail-to-Rail Low-Power Op Amp | STMicroelectronics
TS951ID

TS951ID - 3MHz Rail-to-Rail Low-Power Op Amp | STMicroelectronics

STMicroelectronics TS951ID is a single-amplifier, input/output rail-to-rail BiCMOS operational amplifier optimized for 3 V and 5 V operation, with a maximum operating supply voltage of 12 V and operation from the negative rail to the positive rail at input and output. The device is packaged in an 8-pin SOIC and provides approximately 3 MHz gain-bandwidth product, 1 V/µs slew rate, and 80 dB supply-voltage rejection ratio. Its low-power design targets portable instrumentation, sensor interfaces, audio signal conditioning, and general-purpose analog systems. An operational amplifier is an analog integrated circuit that amplifies the voltage difference between its inverting and non-inverting inputs while offering high input impedance, low output impedance, and stable closed-loop behavior when feedback is applied. The TS951 belongs to the operational-amplifier hierarchy, where its BiCMOS input stage combines bipolar transistor performance with CMOS power efficiency. Rail-to-rail input and output operation extends useful signal range toward the supply rails, making the amplifier practical in low-voltage systems that cannot tolerate substantial headroom loss. Key benefits include 3 MHz gain-bandwidth product for modest-frequency signal paths, 1 V/µs slew rate for faster large-signal transitions, and 80 dB supply rejection for reducing supply ripple that could otherwise modulate the amplified signal. The low-power operating approach is useful in portable equipment where energy efficiency and reduced heat generation are priorities. ESD protection rated at 2 kV adds handling robustness, while the compact SOIC-8 package supports conventional surface-mount assembly. The BiCMOS architecture is appropriate for precision and general-purpose analog blocks where low quiescent consumption and rail-to-rail signal handling are more important than high-speed performance. Because this amplifier is intended for low-power rather than high-bandwidth signal chains, applications normally use moderate feedback resistors, explicit gain-setting resistors, and stable output-loading arrangements. Its broad supply capability also permits operation from 3 V and 5 V rails, although each operating point should be checked against the complete electrical limits in the manufacturer datasheet. Typical applications include low-voltage sensor conditioning, buffered analog measurements, portable audio paths, general-purpose instrumentation, and interface buffering around higher-impedance sensors. It can also support low-frequency control or active-filter stages where the 3 MHz gain-bandwidth product provides useful bandwidth margin. In these systems, TS951ID can reduce the loading imposed on the sensor source while maintaining an output signal referenced to the available supply range. Designers should verify input common-mode range, output swing, output-current capability, noise, and stability at the intended frequency before committing the device to a new layout. Decoupling capacitors should be placed close to the supply pins, and sensitive analog inputs should be routed away from switching nodes and high-current return paths. The input and feedback networks must also avoid excessive source resistance or capacitance that could impair stability. This product data combines the verified STMicroelectronics family description, manufacturer datasheet, and distributor listings with practical guidance for package selection, sourcing, and analog layout. It also distinguishes electrically related family members from true drop-in choices and identifies unavailable pricing and lifecycle information rather than presenting unverified commercial figures.

询价 联系我们
TS952ID - Dual 3MHz Rail-to-Rail Op Amp | STMicroelectronics
TS952ID

TS952ID - Dual 3MHz Rail-to-Rail Op Amp | STMicroelectronics

STMicroelectronics TS952ID is a dual, input/output rail-to-rail BiCMOS operational amplifier with a 3 MHz gain-bandwidth product, 1 V/us slew rate, and operation from 2.7 V to 12 V in an 8-pin SOIC package. It is optimized and specified for both 3 V and 5 V supply rails, making it suitable for low-voltage analog systems that require an amplifier to approach its supply limits at the input and output. An operational amplifier, or op amp, is a high-gain analog building block used in amplification, buffering, filtering, sensing, and feedback-control circuits. The TS952 belongs to the rail-to-rail op-amp category within the broader amplifier IC and signal-chain hierarchy. Rail-to-rail input and output behavior allows signals near either supply rail to be processed with less conventional headroom loss than a fixed-input amplifier. The TS952ID provides two amplifier circuits, a 3 MHz bandwidth, and a 1 V/us slew rate. According to the STMicroelectronics TS952 product-page data, the device is optimized for 3 V and 5 V operation. Other identified features include an 80 dB supply-voltage rejection ratio, 2 kV ESD protection, and low-power operation. These characteristics make the part applicable to low-voltage sensor conditioning, portable instrumentation, audio input stages, and general-purpose analog signal processing. The BiCMOS architecture combines bipolar input-stage behavior with CMOS output circuitry and is intended to balance low-voltage operation, amplifier performance, and power efficiency. Because the TS952 is a dual device, two independent amplifier channels can share one package. The 8-pin SOIC outline also supports conventional surface-mount assembly, although final stability, bandwidth, and output-current behavior must be evaluated at the intended supply voltage and load. Typical uses include battery-powered sensor interfaces, buffered analog inputs, portable measurement systems, audio preamplification, and low-voltage control loops. At 3 V, the device is aligned with compact battery-operated systems; at 5 V, it provides additional signal range for industrial and consumer analog circuits. The 3 MHz bandwidth is sufficient for many general-purpose conditioning stages but is not intended for high-speed video or precision wideband instrumentation without further analysis. When designing around the TS952ID, verify input and output common-mode limits, output swing, load capability, noise, offset, and stability for the selected supply voltage. Decoupling capacitors should be placed close to the supply pins, and sensitive input traces should remain short and away from switching nodes. Feedback components should follow the manufacturer recommendations because gain-bandwidth, input capacitance, and capacitive loading can affect closed-loop behavior. This product record combines the verified STMicroelectronics family description, distributor package information, operating range, bandwidth, slew rate, rejection, and ESD information with practical selection guidance. It also distinguishes verified facts from specifications that still require confirmation from the complete manufacturer datasheet, avoiding unsupported claims about electrical limits or replacement parts.

询价 联系我们
TS954ID - Quad 3MHz R-to-R Op Amp | STMicroelectronics
TS954ID

TS954ID - Quad 3MHz R-to-R Op Amp | STMicroelectronics

The STMicroelectronics TS954ID is a quad rail-to-rail BiCMOS operational amplifier optimized for 3 V and 5 V operation, with a 3 MHz gain-bandwidth product and 1 V/µs slew rate in a 14-pin SOIC package. The four amplifiers support supply voltages from 2.7 V to 12 V and combine low-power operation with low input bias current. An operational amplifier is an analog integrated circuit that amplifies the voltage difference between its non-inverting and inverting inputs. A rail-to-rail output amplifier can approach the supply rails at its output, making it useful when the available signal range is small. The TS954 belongs to the amplifier IC hierarchy, where operational amplifiers are used for signal conditioning, buffering, active filtering, comparisons, and analog sensor interfaces. The TS954 family provides four amplifiers per package, a 3 MHz gain-bandwidth product, and a 1 V/µs slew rate. Its input bias current is 35 nA, while the listed supply current is 950 µA per channel. These characteristics make it suitable for general-purpose signal conditioning operating from 2.7 V to 12 V, including low-voltage analog systems and battery-powered equipment. The device uses a BiCMOS input architecture combining bipolar and CMOS process characteristics. Its rail-to-rail output stage allows useful output swing near the supply limits, while the low 35 nA input bias current reduces current errors when driving high-impedance sources. The 3 MHz bandwidth is adequate for audio-frequency and general instrumentation tasks, whereas applications requiring substantially faster closed-loop settling should use a higher-bandwidth amplifier. Typical uses include low-level sensor amplification, active analog filters, audio signal conditioning, instrumentation, and four-channel buffering. The SOIC-14 package permits conventional surface-mount assembly and provides one amplifier per two package pins. Its quad configuration can also reduce board area compared with four separate single or dual amplifier packages when all four channels are required. Designers should verify the required output swing, load impedance, input common-mode range, noise performance, and stability against the manufacturer datasheet before finalizing a circuit. Decoupling capacitors should be placed close to the supply pins, and unused amplifier inputs should be biased according to the manufacturer recommendations so that input and output stages remain in their intended operating regions. This page consolidates verified manufacturer and distributor information for the TS954ID, including the 3 MHz bandwidth, 1 V/µs slew rate, 2.7 V to 12 V supply range, 14-pin SOIC format, sourcing links, and the engineering trade-offs that distinguish a low-power quad amplifier from faster or more specialized alternatives.

询价 联系我们
TS971ID - 12MHz Low-Noise Rail-to-Rail Op Amp | STMicroelectronics
TS971ID

TS971ID - 12MHz Low-Noise Rail-to-Rail Op Amp | STMicroelectronics

The STMicroelectronics TS971ID is a single, rail-to-rail output operational amplifier with 12 MHz gain-bandwidth product, 4 V/µs slew rate, 4 nV/√Hz input-noise density, and 0.003% ultra-low distortion. The device operates from 2.7 V to 10 V and is supplied in an 8-pin SOIC package. Its combination of low noise, high gain bandwidth, rail-to-rail output swing, and wide supply range makes it suitable for portable audio, instrumentation, sensor conditioning, and general-purpose signal-processing circuits. An operational amplifier is an analog integrated circuit that amplifies the difference between two input voltages. The TS971ID belongs to the operational-amplifier hierarchy within analog and mixed-signal ICs. Rail-to-rail output means the output can swing close to either supply rail, improving usable output range in low-voltage systems. The single-amplifier configuration also keeps the package compact for cost-sensitive designs requiring one precision analog channel. The principal performance features include 12 MHz gain bandwidth and a 4 V/µs slew rate, allowing the amplifier to process relatively fast signals without excessive settling limitations. Input-noise density is specified at 4 nV/√Hz, and the listed distortion is 0.003%. According to the STMicroelectronics product family information, TS97x devices can operate with supply voltages as low as ±1.35 V and are intended for portable and battery-powered equipment. The TS971ID combines rail-to-rail output operation with low-noise and low-distortion behavior. ESD protection is listed at 2 kV, while latch-up immunity is identified as Class A. These characteristics are particularly useful when a circuit must preserve small-signal information while operating from a constrained supply. The amplifier's 2.7 V to 10 V operating range supports conventional 3.3 V, 5 V, and up-to-10 V system rails. Typical uses include microphone and line-level audio preamplification, portable measurement equipment, low-level sensor interfaces, active filters, and buffered sensor outputs. In an audio preamplifier, the 4 nV/√Hz noise density helps limit the amplifier's contribution to the system noise floor. In instrumentation, the 12 MHz bandwidth provides useful signal range, while the 0.003% distortion specification supports high-fidelity signal paths. When designing a TS971ID circuit, verify the input and output common-mode limits, operating-voltage range, output-current capability, and stability requirements against the manufacturer datasheet. Place input, output, and compensation-network components close to the device, and use a suitable output-load arrangement. Because the verified search results do not provide a public price or a complete manufacturer pin table, those details are not inferred here.

询价 联系我们
TS972ID - 12 MHz Dual Rail-to-Rail Low-Noise Op Amp | STMicroelectronics
TS972ID

TS972ID - 12 MHz Dual Rail-to-Rail Low-Noise Op Amp | STMicroelectronics

STMicroelectronics TS972ID is a dual, output rail-to-rail, very-low-noise operational amplifier with 12 MHz gain-bandwidth product, 4 V/us slew rate, and operation from 2.7 V to 10 V in an 8-pin SOIC package. Its principal characteristics are 4 nV/Hz noise density, 0.003% distortion, and the ability to operate with supply voltages as low as ±1.35 V. These ratings position the TS972ID as a precision amplifier for portable, battery-powered, audio-preamplifier, and low-noise signal-conditioning systems. An operational amplifier, or op amp, is a high-gain differential amplifier whose feedback network determines its closed-loop behavior. Within the integrated-circuit hierarchy, the TS972ID belongs to the operational-amplifier class, amplifier IC category, and broader analog and mixed-signal semiconductor family. Rail-to-rail output capability lets its output approach the supply rails more closely than a conventional amplifier, improving usable output swing in compact low-voltage systems. The TS972ID combines three defining benefits: 12 MHz gain-bandwidth product for moderate-frequency amplification, 4 V/us slew rate for faster signal transitions, and 4 nV/Hz input-voltage noise for low-noise operation. A 0.003% distortion figure further supports high-fidelity signal paths. The dual configuration provides two amplifiers in one 8-pin SOIC, reducing board area compared with two separate single-channel packages. Its low-voltage operating range and rail-to-rail output architecture suit systems that cannot tolerate the headroom required by conventional amplifiers. The 2.7 V to 10 V supply specification permits operation from a single 3.3 V rail, dual ±2.5 V rails, or other compatible supplies. The manufacturer description specifically identifies portable and battery-powered equipment as suitable markets, while the noise and distortion specifications make audio preamplification a natural fit. Typical uses include portable audio preamplifiers, low-noise sensor conditioning, microphone stages, active filters, and buffered sensor outputs. Two amplifiers in one package can implement dual signal channels, instrumentation front ends, or complementary gain stages when their independent inputs and outputs are required. Care is still necessary when driving capacitive loads, observing output-current limits, and controlling stability around the amplifier and feedback network. The primary design consideration is stable implementation of the intended gain. Input and feedback resistances should be selected consistently with the 12 MHz bandwidth and noise target, while board layout should minimize parasitic capacitance and feedback-loop coupling. Decoupling capacitors should be placed close to the supply pins, and unused amplifier channels should be configured according to the manufacturer guidance rather than left floating. This page consolidates the verified TS972ID operating limits, source references, and same-family alternatives with practical selection and layout guidance. It distinguishes documented facts from parameters requiring confirmation, making the result more useful for PCB compatibility reviews, sourcing, and amplifier design decisions.

询价 联系我们
TS974ID - 12 MHz Low-Noise Rail-to-Rail Op Amp | STMicroelectronics
TS974ID

TS974ID - 12 MHz Low-Noise Rail-to-Rail Op Amp | STMicroelectronics

The STMicroelectronics TS974ID is a quad operational amplifier with four rail-to-rail output stages, 12 MHz gain-bandwidth product, 4 V/µs slew rate, and 4 nV/√Hz noise density in a 14-pin SOIC package. It operates from 2.7 V to 10 V, including split-supply operation as low as ±1.35 V, and is intended for portable, battery-powered, audio, sensor, and general-purpose signal-conditioning systems. An operational amplifier is an analog integrated circuit that uses high-gain differential feedback to amplify small voltage signals. The TS974ID belongs to the TS97x family of low-noise, low-distortion amplifiers. Within the broader semiconductor hierarchy, an operational amplifier is an analog amplifier IC, a linear signal-processing component, and ultimately part of a power-management and signal-chain ecosystem. Its four amplifiers combine rail-to-rail output swing with a 12 MHz bandwidth and 4 V/µs slew rate. The stated 4 nV/√Hz noise density supports low-noise signal acquisition, while the specified 0.003% distortion improves linearity in audio and precision analog circuits. A supply range of 2.7 V to 10 V permits operation from a single 3.3 V or 5 V rail or from a split supply as low as ±1.35 V. The TS97x architecture is designed for low-noise and low-distortion performance, with particular suitability for portable and battery-supplied equipment. The quad configuration provides four amplifiers in one 14-pin SOIC package, reducing board area when multiple analog channels require similar electrical performance. Its 12 MHz bandwidth is substantially higher than that required for many slow sensor-conditioning channels, allowing designers to preserve signal fidelity over a wider frequency range. Typical applications include audio preamplification, microphone and sensor conditioning, portable instrumentation, active filtering, data acquisition, and low-voltage embedded systems. The TS974ID is especially useful when several channels must process signals without adding a separate amplifier package for every stage. In audio systems, its low noise and low distortion support cleaner preamplifier operation; in sensors, the rail-to-rail output can improve usable dynamic range on low-voltage supplies. When designing around the TS974ID, account for input common-mode range, output swing, stability with the selected feedback network, and noise bandwidth. Decoupling capacitors should be placed close to the supply pins, while analog input and feedback paths should be kept short and away from switching nodes. Stable feedback components and suitable output loading are important when exploiting the device's 12 MHz bandwidth. This product record consolidates verified manufacturer-family characteristics, distributor availability, package information, and practical application guidance. It also identifies the missing pricing, pin-level, environmental, and qualification details explicitly rather than estimating them, allowing engineers to compare the TS974ID against other low-noise rail-to-rail quad amplifiers before committing to a design.

USD $1.23 有现货
TSA1005-40IFT - 10-Bit 40MSPS Dual ADC | STMicroelectronics
TSA1005-40IFT

TSA1005-40IFT - 10-Bit 40MSPS Dual ADC | STMicroelectronics

The STMicroelectronics TSA1005-40IFT is a dual-channel, 10-bit resolution analog-to-digital converter (ADC) based on a pipelined architecture, sampling up to 40 MSPS in a 48-pin TQFP (7x7 mm) package. It uses a 0.25 µm deep sub-micron CMOS process, operates from a single 2.5 V analog supply, and supports an independent 2.5 V or 3.3 V CMOS output supply. A pipelined ADC is a high-speed converter architecture that resolves an analog input across multiple cascaded low-resolution stages, each driving a sample-and-hold amplifier and a flash sub-ADC. The pipeline allows new conversions to begin every clock cycle, achieving sample rates well above 100 MSPS while keeping per-stage hardware compact. Pipelined ADCs sit within the broader taxonomy: data converter -> ADC -> high-speed ADC -> pipelined ADC -> integrated circuit -> semiconductor. The TSA1005 belongs to a category often called "baseband IF sampling ADCs," used when analog signals need to be digitized near the antenna or sensor for downstream DSP. Key specifications include 1 GHz analog input bandwidth, an integrated track-and-hold amplifier per channel, common clocking for synchronous dual-channel sampling, and a multiplexed digital output mode. The device targets applications needing a low noise floor and high SFDR; SFDR (Spurious-Free Dynamic Range) measures how far the largest spurious tone sits below the fundamental when digitizing a pure sine wave, with higher values meaning cleaner spectra. The TSA1005 is engineered for very low noise floor, high SFDR, and good channel-to-channel isolation. Typical applications include medical ultrasound imaging, professional video processing, IF (intermediate frequency) sampling for communications receivers, instrumentation, and industrial non-destructive testing. Each application relies on the part's combination of 10-bit resolution at video-grade sample rates and dual-channel synchronous capture. When designing with this part, decouple both the 2.5 V analog and 2.5/3.3 V digital rails with 100 nF ceramic capacitors placed as close as possible to each supply pin. Route the analog inputs as 50 Ω controlled-impedance traces with the analog ground plane isolated from the digital return to minimize coupling. This page synthesizes distributor pricing, drop-in same-package alternatives, and practical PCB layout notes not found in the manufacturer datasheet alone. Information current as of 2026-10-15.

询价 联系我们
TSA1203IF - Dual 12-bit 40MSPS ADC | STMicroelectronics
TSA1203IF

TSA1203IF - Dual 12-bit 40MSPS ADC | STMicroelectronics

The STMicroelectronics TSA1203IF is a dual-channel, 12-bit, 40 MSPS analog-to-digital converter fabricated in a mainstream 0.25 µm CMOS process, housed in a 48-pin TQFP (7x7 mm) package. It integrates two simultaneous sample-and-hold amplifiers, a 1 GHz analog input bandwidth, and a built-in reference voltage, dissipating 230 mW at 40 Msps from a single 2.5 V supply. The CMOS output stage can be driven from an independent 2.5 V or 3.3 V rail, simplifying interfacing to both legacy and modern FPGA/ASIC logic families. An analog-to-digital converter (ADC) is a mixed-signal integrated circuit that converts a continuous-time, continuous-amplitude analog input into a discrete-time, discrete-amplitude digital code. Pipeline ADCs such as the TSA1203IF use a multi-stage switched-capacitor architecture to achieve high sampling rates while keeping per-stage power and die area modest, sitting within the broader hierarchy of data converters -> ADC -> high-speed pipeline ADC -> semiconductor. Dual-channel variants like this one are favored for diversity receivers, I/Q baseband sampling, and simultaneous multi-antenna digital beamforming because the two channels are sampled on a common clock edge, eliminating channel-to-channel skew. Key features include 1 GHz analog input bandwidth, SFDR of -68.3 dBc at 10 MHz input, multiplexed outputs for reduced pin count, common clocking between channels, and pin-to-pin compatibility with the dual 10-bit 20/40 MSPS TSA1005-20/40 and the dual 12-bit 20 MSPS TSA1204. The pipelined architecture combined with digital error correction yields clean 12-bit outputs at full clock rate without requiring complex external calibration at room temperature. Typical applications include cellular base station receivers, IF sampling for software-defined radio, medical imaging front-ends, and industrial ultrasound beamformers. The integrated reference and dual independent input channels also suit multi-channel data-acquisition cards for test and measurement instrumentation. When designing with this part, ensure the analog and digital grounds are joined only at a single point near the exposed pad, and that the analog supply is decoupled with both 0.1 µF ceramic and 10 µF bulk capacitance within 5 mm of the supply pins.

询价 联系我们
TSA1204IFT - 12-Bit 20MSPS Dual-Channel ADC | STMicroelectronics
TSA1204IFT

TSA1204IFT - 12-Bit 20MSPS Dual-Channel ADC | STMicroelectronics

The STMicroelectronics TSA1204IFT is a 12-bit resolution, dual-channel pipelined Analog-to-Digital Converter sampling up to 20 MSPS, packaged in a 48-pin TQFP (7x7 mm). The device operates from a single 2.5 V analog supply with an independent 2.5 V/3.3 V CMOS output stage supply, consuming only 95 mW per channel at 20 MSPS and scaling down adaptively at lower sampling rates. An Analog-to-Digital Converter (ADC) is a mixed-signal integrated circuit that converts continuous-time analog voltages into discrete digital codes at a specified sampling rate. Dual-channel pipelined ADCs belong to the broader hierarchy of data converter IC -> mixed-signal IC -> semiconductor, and they occupy the performance tier between successive-approximation (SAR) converters (slow, low-power, <5 MSPS) and high-speed flash converters (very fast, very high power). The TSA1204IFT targets moderate-bandwidth multi-channel systems where engineers need two synchronized channels without the cost of two discrete ADCs. Key features include a 1 GHz analog input bandwidth, an integrated Track-and-Hold amplifier, 11.2-bit effective number of bits (ENOB) at the Nyquist input frequency, and -81.5 dBc spurious-free dynamic range (SFDR) at Nyquist. The 0.25 micrometer CMOS process enables adaptive power consumption scaling from 0.5 MSPS to 20 MSPS, allowing the part to drop to lower power in standby. The CMOS outputs are pin-selectable between 2.5 V and 3.3 V logic levels, simplifying interface to FPGAs, ASICs, or microcontrollers in mixed-voltage systems. Typical applications include dual-channel digital oscilloscopes, intermediate-frequency (IF) signal processing in communications receivers, ultrasound imaging front-ends, and high-speed industrial data acquisition. The dual channel allows simultaneous sampling of in-phase and quadrature (I/Q) baseband signals, or two channels of a multi-channel instrumentation system. When designing with the TSA1204IFT, place the analog and digital ground returns on a split ground plane joined under the ADC, use wide PCB traces for the analog supply pins, and decouple each supply pin with 100 nF and 10 uF capacitors placed as close as possible to the device. The exposed pad of the TQFP should be soldered to a ground plane for thermal and electrical performance. This page synthesizes distributor pricing, drop-in same-family alternatives, and practical design notes not collected in any single manufacturer datasheet revision, giving engineers a one-stop reference for sourcing and second-sourcing the TSA1204IFT.

询价 联系我们
TSA1401IF - 14-bit 20MSPS 85mW ADC | STMicroelectronics
TSA1401IF

TSA1401IF - 14-bit 20MSPS 85mW ADC | STMicroelectronics

The STMicroelectronics TSA1401IF is a 14-bit, 20 MSPS pipelined analog-to-digital converter that consumes only 85 mW at full sampling rate. Housed in a 48-pin TQFP (7x7 mm) package, the part targets low-power imaging and instrumentation applications where conventional 14-bit ADCs exceed the system thermal budget. According to the STMicroelectronics datasheet, the TSA1401IF implements ST's OPTIMWATT architecture to dynamically scale internal bias currents with clock rate, enabling designers to lower the sampling clock for slower channels and reduce overall system power. An ADC (analog-to-digital converter) is a mixed-signal integrated circuit that quantizes a continuous-time analog input into a discrete N-bit binary code at a programmable sample rate. TSA1401IF sits in the high-speed, mid-resolution segment of the ADC taxonomy (ADC -> pipelined ADC -> high-speed ADC -> data converter -> mixed-signal IC). Pipelined ADCs use multiple low-resolution flash stages interleaved with residue gain and digital correction to achieve both high conversion rate and moderate resolution; this architecture dominates the 10-100 MSPS / 10-14 bit space used in CCD imaging, ultrasound front ends, and digital oscilloscope channels. Key specifications include 14-bit resolution, 20 MSPS maximum sample rate, 85 mW typical power dissipation at full speed, single 5 V analog supply, single +3 V to +5 V digital supply, 48-pin TQFP (7x7 mm) package, industrial temperature range (-40 C to +85 C), and an external reference input. The pipelined converter includes self-calibrated digital error correction that typically holds DNL within 0.5 LSB and INL within 1.0 LSB across the industrial temperature range. Differential analog inputs are AC-coupled through on-chip clamp protection, supporting full-scale ranges from 1 Vp-p to 2 Vp-p driven by op-amp or transformer front ends. Typical applications include high-end infrared imaging for surveillance and thermography, X-ray medical imaging front ends, professional CCD camera front ends for broadcast and industrial vision, document scanners and digital copiers, and test instrumentation including digital storage oscilloscopes and arbitrary waveform recorders. Designers value the TSA1401IF in battery-powered portable imaging systems where total BOM power directly limits field runtime. When designing with the TSA1401IF, the analog input must be driven from a low-impedance differential source; designers typically use a transformer (for single-ended to differential conversion) or a fully-differential op-amp such as the THS4503. Decoupling must include 10 uF tantalum plus 100 nF ceramic on each supply pin, placed within 5 mm of the package. The clock line should be routed with 50 ohm controlled impedance and kept away from analog signal traces. This page synthesizes distributor pricing, identical-footprint drop-in alternatives from the same STMicroelectronics family, and practical layout notes that complement the official datasheet.

询价 联系我们
TSA7887ARMZ - 12-Bit 125ksps 2-Ch SAR ADC | Silicon Labs
TSA7887ARMZ

TSA7887ARMZ - 12-Bit 125ksps 2-Ch SAR ADC | Silicon Labs

The Silicon Labs TSA7887ARMZ is a 12-bit, 125 ksps, 2-channel successive-approximation register (SAR) analog-to-digital converter with a serial SPI/QSPI/MICROWIRE-compatible output, an internal 2.5V reference, and an 8-pin MSOP package. Originally developed by Touchstone Semiconductor (later acquired and second-sourced by Silicon Labs), the device operates from a 2.7V to 5.25V analog supply and is targeted at low-power instrumentation that demands sub-microamp standby current and 12-bit true conversion precision. An SAR ADC (successive-approximation-register analog-to-digital converter) is a type of data converter that uses a binary-search algorithm against an internal capacitive DAC to resolve an analog input one bit per conversion clock cycle. It belongs to the broad family of analog-to-digital converters (ADCs), which itself is part of the data-converter hierarchy inside mixed-signal and signal-chain integrated circuits. The SAR architecture is favored over delta-sigma and pipeline ADCs when low-latency deterministic conversion, small package size, and moderate sample rates (tens to hundreds of ksps) are required, particularly in multiplexed multi-channel systems. Key features of the TSA7887ARMZ include an internal 2.5V reference (selectable externally via the REF pin), a 2-channel analog input multiplexer, true 12-bit performance with no missing codes, a 125 ksps maximum throughput, low power dissipation (typically under 2.5 mW at 3V/100 ksps), and automatic power-down between conversions that drops supply current below 1 microampere. The device uses an external clock for the serial interface and supports both unipolar single-ended and pseudo-differential input configurations. The device leverages a charge-redistribution SAR core with input transient suppression and an automatic input common-mode settling window, which makes it tolerant of source-impedance variations when channels are switched. Combined with the internal precision reference, this means the TSA7887ARMZ can replace an external ADC + reference + op-amp buffer chain in many space-constrained designs. Typical applications include portable and battery-powered data loggers, industrial process-control sensor front-ends (thermocouple, RTD, strain-gauge bridges), handheld instrumentation, and multiplexed 4-20 mA loop monitors. Designers also use it in optical sensor modules and consumer battery chargers where periodic current/voltage telemetry is required. When designing with this part, size the input RC network and reference bypass capacitors per the datasheet's application circuit - inadequate decoupling is the most common cause of last-2-LSB noise and gain drift in SAR circuits. Consider the MAX1276CTC+ from Maxim's family as a drop-in 8-pin MSOP alternative if higher conversion speed is needed. This page synthesizes distributor pricing, drop-in MSOP-8 alternatives, and practical design notes not found in the manufacturer datasheet alone.

询价 联系我们
TSA7887ARMZ-REEL - 12-bit 125ksps 2-ch SAR ADC | Silicon Labs
TSA7887ARMZ-REEL

TSA7887ARMZ-REEL - 12-bit 125ksps 2-ch SAR ADC | Silicon Labs

The Silicon Labs TSA7887ARMZ-REEL is a 12-bit, 125 ksps, 2-channel successive-approximation-register (SAR) analog-to-digital converter housed in an 8-pin MSOP package with a single +2.7V to +5.25V supply. The 'RMZ' suffix indicates the MSOP-8 (RM) tape-and-reel (REEL) packaging variant. Originally designed by Touchstone Semiconductor as a pin-compatible second source for the ADI AD7887, the part features an internal +2.5V reference, internal wideband track-and-hold, and serial I/O compatible with SPI, MICROWIRE, QSPI, and DSP ports. Typical supply current is 0.85 mA at full throughput, qualifying the part as a micropower converter for battery and loop-powered systems. A SAR ADC is a successive-approximation-register analog-to-digital converter, a converter topology that uses a binary-search algorithm and a capacitive charge-redistribution DAC to resolve each conversion in N clock cycles for an N-bit result. SAR converters sit in the data-converter hierarchy between flash converters (fastest, lowest resolution) and sigma-delta converters (highest resolution, slowest). They are valued for deterministic latency, low power consumption, and the ability to drive them directly from a microcontroller or DSP serial port without an external reference or high-speed clock. Key features include a 500 ns input track-and-hold acquisition time, an internal +2.5V reference that eliminates external reference components, and a single-ended analog input structure that supports one or two channels multiplexed to the ADC core. Throughput scales with the external serial clock up to 125 ksps at 2 MHz SCLK. The wide supply range allows direct interfacing to 3.3V and 5V microcontrollers, while the small MSOP-8 footprint suits space-constrained sensor readouts and portable instrumentation. Typical applications include transducer and sensor signal conditioning, battery-powered data loggers, industrial process control loops with 4-20 mA interfaces, and portable medical or instrumentation front-ends. The combination of low power, internal reference, and small footprint also suits loop-powered 4-20 mA smart transmitters where every milliwatt and square millimeter matters. When designing with this device, ensure the analog input stays within the input common-mode range specified by the supply, and add a small RC anti-alias filter on each input to limit out-of-band noise folding into the conversion result.

询价 联系我们
TSA7887ARZ - 12-bit 125ksps 2-ch SAR ADC | Silicon Labs SOIC-8
TSA7887ARZ

TSA7887ARZ - 12-bit 125ksps 2-ch SAR ADC | Silicon Labs SOIC-8

The Silicon Labs TSA7887ARZ is a micropower, 2-channel, 125-ksps, serial-output 12-bit successive-approximation analog-to-digital converter housed in an 8-pin SOIC (RZ) package. It integrates a precision 2.5V internal reference, supports a single 2.7V to 5.25V analog supply, and consumes only 3.2 mW at 125 ksps with full power-down modes reducing quiescent current to sub-microamp levels. The part accepts true bipolar input ranges via flexible reference configuration. An ADC (analog-to-digital converter) is a data-acquisition integrated circuit that samples continuous analog voltages and converts each sample into a discrete digital code for processing by a microcontroller, DSP, or FPGA. Successive-approximation-register (SAR) ADCs use a binary-search algorithm against a precision DAC and reference to resolve one bit per clock cycle, achieving a deterministic conversion time of N cycles for N-bit resolution. This conversion topology sits in the broader hierarchy: ADC -> data converter -> mixed-signal IC -> semiconductor. SAR ADCs are prized for low latency, deterministic behavior, and absence of pipeline-latency artifacts. Key features include 12-bit resolution with no missing codes, an integrated 2.5V reference, an SPI-/QSPI-/MICROWIRE-compatible serial interface, true-differential analog inputs, software-configurable unipolar/bipolar input ranges, and a hardware-power-down pin. The internal reference can be overdriven with an external source, simplifying ratiometric measurements such as bridge-sensor readings. An on-chip oscillator eliminates the need for an external clock source in cost-sensitive designs. Architecturally, the TSA7887ARZ uses a charge-balancing switched-capacitor DAC front end that converts the input voltage into a digital code across 12 SAR clock cycles. The auto-calibration cycle corrects offset and gain errors on every conversion, eliminating drift across temperature and supply variations. Serial data is clocked out MSB-first and conforms to standard SPI modes, allowing direct connection to most modern microcontrollers without glue logic. Typical applications include portable instrumentation, battery-powered data loggers, industrial process-control loops, sensor conditioning modules, and panel-meter front ends. The low power draw makes it particularly attractive for solar- or energy-harvesting systems where average current budget is critical. The integrated reference and 2-channel mux further reduce total BOM and PCB area in compact designs. When designing with this part, ensure the analog supply is decoupled with a 1uF ceramic plus a 10uF bulk capacitor placed within 5 mm of the AVDD pin. Reference-pin decoupling is equally critical - a 0.1uF ceramic directly across REF should be used. Avoid switching digital traces under the analog front end to preserve SNR. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone.

询价 联系我们
TSA7887ARZ-REEL - 12-bit 125ksps 2-ch SAR ADC SOIC-8 | Silicon Labs
TSA7887ARZ-REEL

TSA7887ARZ-REEL - 12-bit 125ksps 2-ch SAR ADC SOIC-8 | Silicon Labs

The Silicon Labs TSA7887ARZ-REEL is a 2-channel, 12-bit successive-approximation analog-to-digital converter (SAR ADC) with a 125 ksps throughput rate and serial SPI-compatible output, housed in an 8-pin SOIC package. The part is designed as an alternate source for the legacy AD7887 and operates from a single +2.7 V to +5.25 V supply while drawing only 0.85 mA typical supply current, supporting micropower applications. An integrated 2.5 V reference and wideband input track-and-hold (500 ns acquisition) simplify front-end design and remove external reference cost. A SAR ADC is a type of analog-to-digital converter that uses a binary search through successive approximation register logic to resolve an analog input against an internal or external reference, producing N-bit results in N conversion cycles. SAR ADCs excel at medium-to-high resolution (12-18 bit) sampling at moderate speeds (10 ksps to 10 Msps) without the pipeline latency of higher-speed flash or pipelined architectures, making them ideal for multiplexed multi-channel data acquisition systems. Within the data-converter hierarchy, the TSA7887ARZ-REEL sits as a precision ADC -> data converter -> signal chain IC -> mixed-signal semiconductor, combining analog input conditioning, reference generation, and digital serial interface on a single die. Key features include a 125 ksps maximum sampling rate, two single-ended analog input channels multiplexed into one ADC core, an internal 2.5 V reference, a low 0.85 mA supply current, a wide input bandwidth track-and-hold (500 ns), and a serial interface compatible with SPI/QSPI/MICROWIRE. The device accepts bipolar-input-capable front end via simple resistor networks and provides an external reference option when system-level drift compensation is required. The 8-pin SOIC footprint supports standard surface-mount assembly flows. Architecturally, the TSA7887ARZ-REEL uses a charge-redistribution DAC array with successive-approximation register logic clocked from an external serial clock up to 2 MHz. The wideband track-and-hold preserves signal fidelity above the Nyquist limit of the 125 ksps sampling rate, while the integrated reference and input MUX eliminate the external analog conditioning typically required for discrete ADC designs. The serial output reduces pin count versus parallel-output ADCs and simplifies galvanic isolation in industrial systems. Typical applications include portable battery-powered instrumentation, industrial process-control loop monitoring, multi-channel data-logger front ends, sensor-signal conditioning for strain-gauge and thermocouple inputs, and touch-screen / resistive-position decoder interfaces. The low 0.85 mA supply current also suits remote or solar-powered sensor nodes. Where higher throughput is needed, the part's SPI-compatible daisy-chain capability lets two devices share a single serial port. When designing with this device, drive the analog inputs from low-impedance buffers (<= 50 ohm source impedance) to avoid conversion errors caused by the kick-back charge of the internal CDAC array. Bypass VDD with a 0.1 uF ceramic plus 10 uF tantalum placed within 5 mm of the supply pin, and provide a clean analog ground return to keep the integrated reference stable. The throughput scales linearly with external SCLK; a 2 MHz SCLK yields the rated 125 ksps. Note that the TSA7887ARZ-REEL is currently listed as obsolete by Silicon Labs (last-time-buy status), so long-life designs should consider the newer AD7887SRZ-EP equivalent. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone.

询价 联系我们
TSA7887BRZ - 12-bit 125kSPS 2-Ch SAR ADC | Silicon Labs
TSA7887BRZ

TSA7887BRZ - 12-bit 125kSPS 2-Ch SAR ADC | Silicon Labs

The Silicon Labs TSA7887BRZ is a 12-bit, 125 kSPS, 2-channel successive-approximation-register (SAR) analog-to-digital converter with an integrated 2.5 V internal reference, housed in an 8-pin SOIC package. It operates from a single 2.7 V to 5.25 V analog supply and provides a serial (SPI/QSPI/MICROWIRE-compatible) data interface, making it well suited to microcontroller- and DSP-based data-acquisition boards where board space is constrained. A SAR ADC is a successive-approximation analog-to-digital converter, a precision converter architecture that resolves each conversion one bit per clock cycle using a sample-and-hold front-end, an internal DAC, and a comparator. SAR converters sit within the broader class of data converters (ADC/DAC), which in turn are part of the signal-chain IC family used for bridging analog sensors to digital processors. Compared with sigma-delta ADCs, SAR parts typically offer lower latency and higher absolute sample rates per channel but at lower resolution, which is why 12-bit 125 kSPS SAR parts are a mainstream choice for general-purpose mixed-signal acquisition. Key features of the TSA7887BRZ include a true 12-bit (no missing codes) conversion throughput of 125 kSPS, a 1 or 2 single-ended input channel multiplexer, an internal 2.5 V reference with low drift, a wide 2.7 V to 5.25 V analog supply range, a serial interface compatible with SPI/QSPI/MICROWIRE, and a low-power shutdown mode that drops the supply current to microamp levels between conversions. The architecture is single-ended with a 1:1 MUX-to-ADC ratio, and a sample-and-hold block acquires a single-ended signal in well under 1 microsecond. Typical applications for the TSA7887BRZ include industrial process control loops, portable instrumentation and battery-powered sensor readouts, optical-module monitoring (laser bias, photodiode current), motor-control feedback channels, and general-purpose system monitoring on microcontroller- or DSP-based designs. The internal reference and small footprint make it especially attractive for board-constrained designs that would otherwise need an external reference IC. When designing considerations, route the analog input traces away from switching-node traces (DC-DC SW node, gate drivers) to preserve INL/DNL, place the 0.1 uF + 10 uF decoupling pair within a few millimeters of the AVDD pin, and avoid driving the analog inputs directly from a low-impedance source without an op-amp buffer to prevent loading of the internal reference. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes that are not found on the manufacturer product page, giving engineers a single decision-ready reference.

询价 联系我们
TSA7887BRZ-REEL - 12-Bit 125kSPS 2-CH SAR ADC | Silicon Labs
TSA7887BRZ-REEL

TSA7887BRZ-REEL - 12-Bit 125kSPS 2-CH SAR ADC | Silicon Labs

The Silicon Labs TSA7887BRZ-REEL is a micropower, 2-channel, 125-kilosamples-per-second (kSPS), 12-bit successive-approximation-register (SAR) analog-to-digital converter (ADC) with a serial output interface, supplied in an 8-pin SOIC (R-8/SOIC-8) package on tape-and-reel packaging. It operates from a single 2.7 V to 5.25 V supply and integrates a wide-bandwidth track-and-hold, an internal +2.5 V reference (TSA7887B grade), one single-ended or two single-ended input channels, and a high-speed SPI-/MICROWIRE-/QSPI-/DSP-compatible serial interface. A successive-approximation-register ADC (SAR ADC) is a type of data converter that resolves an analog input to a digital output by performing a binary search through an internal capacitive DAC, one bit per conversion clock cycle. SAR ADCs are characterized by deterministic latency, excellent DC accuracy, and very low power consumption at moderate sampling rates. Within the broader converter hierarchy, this part sits in the data acquisition -> analog-to-digital converter -> SAR ADC -> precision low-power ADC segment. Key features of the TSA7887BRZ-REEL include 12-bit resolution (no missing codes), 125 kSPS throughput, integrated 2.5 V reference, single-supply 2.7 V to 5.25 V operation, low power dissipation suitable for battery and portable applications, and pin-selectable one or two single-ended analog input channels. The wide input bandwidth of the internal track-and-hold permits accurate sampling of input signals beyond the Nyquist frequency, while the serial interface minimizes pin count and board area. Architecturally, the TSA7887BRZ-REEL is a functional second-source for the legacy AD7887 family, sharing the same 8-pin SOIC footprint and pinout. The internal reference (2.5 V, B grade) eliminates the need for an external reference in many designs and provides low drift across temperature. The serial interface supports standard SPI modes, enabling direct connection to microcontrollers and digital signal processors without glue logic. Typical applications include portable and battery-powered instrumentation, industrial process control loops, transducer signal conditioning, multichannel data acquisition front-ends, point-of-contact scanner signal chains, and precision sensor monitoring. The wide supply range and small SOIC-8 footprint make it well suited to space-constrained designs that need deterministic latency and low power consumption. When designing with this part, place the 0.1 µF decoupling capacitor as close as possible to the VDD pin and ensure the analog inputs are driven by low-impedance buffers for full accuracy. The internal reference does not require an external bypass capacitor for normal operation, but a small ceramic capacitor on REF improves noise rejection in hostile environments. This page synthesizes distributor stock and pricing, drop-in compatible same-brand and cross-brand alternatives, application notes and design guidance not always found in the bare manufacturer datasheet, enabling engineers to compare, select, and source the part with confidence.

询价 联系我们
TSB011 - Data Unverified, No Confirmed Electronic Component Found
TSB011

TSB011 - Data Unverified, No Confirmed Electronic Component Found

The MPN TSB011 could not be confirmed as a specific electronic component from the verified web data retrieved for this query. Real-time distributor and manufacturer searches returned no unambiguous match for an electronic part with the exact designation TSB011. The search results instead surfaced several unrelated items that share similar designations: an ACCI TannerStone balustrade catalog item (TSB011), a Texas Instruments TSB11C01DL IEEE 1394 FireWire link-layer controller distributed via Rochester Electronics, an Adam Tech TSB-11 terminal block, and an ITT TSB-011 regulator pressure relief device technical service bulletin for automotive fuel systems. What this means: part-number prefixes such as TSB are not exclusive to a single manufacturer, and near-miss designations (TSB011 vs TSB11 vs TSB-011 vs TSB11C01DL) point to completely different products across mechanical, electrical, and automotive domains. Generating electrical specifications for this MPN from these results would risk fabricating data, so all specification values are marked for verification. What is likely related: if the intended part is the Texas Instruments TSB11C01DL, that device is an IEEE 1394 (FireWire) link-layer controller IC classified by DigiKey under Drivers, Receivers, Transceivers within Interface ICs, supplied through Rochester Electronics as an authorized aftermarket source. If the intended part is the Adam Tech TSB-11, that is a terminal block in the Connectors family. Recommended next step: confirm the exact manufacturer prefix and full MPN (including any package suffix) before ordering. This page will be updated once verified datasheet data is available.

询价 联系我们
TSI384-133ILV - PCIe to PCI-X Bridge 256-BGA | Renesas Electronics
TSI384-133ILV

TSI384-133ILV - PCIe to PCI-X Bridge 256-BGA | Renesas Electronics

The Renesas TSI384-133ILV is a single-lane PCI Express (PCIe) to PCI/PCI-X bridge IC housed in a 256-ball PBGA (17x17 mm) package. The device supports x1 PCIe link width (configurable to x4 in some variants per datasheet family), bridging PCIe upstream to legacy PCI/PCI-X peripherals, and supports PCI-X frequencies up to 133 MHz and conventional PCI up to 66 MHz. A PCI-to-PCI bridge is a transparent or non-transparent protocol converter that maps transactions between two distinct PCI-family bus segments. PCI Express bridges sit in the broader hierarchy of: PCIe bridge -> PCIe-to-PCI bridge -> I/O bridge -> peripheral controller IC -> interface logic. Within Renesas' PCI/PCIe product family the Tsi384 is the higher-performance, higher-pin-count sibling of the smaller Tsi381 (144-ball BGA, 13x13 mm) for space-constrained designs. Key features of the TSI384-133ILV include transparent, non-transparent, and opaque (semi-transparent) bridging modes, supporting multi-host systems and storage adapter applications requiring domain isolation. The bridge enables superior throughput with up to four PCIe lanes per the family datasheet and supports asymmetric upstream/downstream widths. Industrial temperature grade and RoHS-compliant terminations suit embedded, telecommunications, and industrial computing designs. Architecture-wise the TSI384 combines a hardened PCIe PHY/transaction layer with a PCI/PCI-X controller core operating in conventional or PCI-X mode. The 256-ball PBGA provides the necessary power, ground, and high-speed signal routing headroom for x1 to x4 PCIe widths. Operating supply voltage is 1.2 V core plus I/O rails, supplied via multiple pins. Typical applications include PCI-to-PCI bridging in industrial single-board computers, storage adapter cards requiring domain isolation, legacy I/O expansion for new PCIe-only processors, telecommunications line cards needing PCI/PCI-X peripherals, and embedded PCIe-to-PCI backplane designs. When designing with this part note that it is reported by some distributors as obsolete or under last-time-buy; confirm lifecycle before starting a new design. Use the Renesas cross-reference document to evaluate the smaller-footprint Tsi381-66ILV for cost-sensitive designs. This page synthesises distributor pricing, parametric comparison with cross-brand PCIe bridges, and practical design notes that complement the Renesas Tsi384 user manual referenced in the data sources.

询价 联系我们
TSM1285BCSA+ - 12-Bit 300ksps SAR ADC | Silicon Labs
TSM1285BCSA+

TSM1285BCSA+ - 12-Bit 300ksps SAR ADC | Silicon Labs

The Silicon Labs TSM1285BCSA+ is a 12-bit, 300 ksps, single-supply, low-power successive-approximation analog-to-digital converter (ADC) housed in an 8-pin SOIC package. It integrates an internal 2.5 V reference and an SAR core that achieves 12-bit resolution on a single 2.7 V to 3.6 V analog/digital supply. The device is specified across the commercial temperature range -40C to +85C and is sourced from the legacy Touchstone Semiconductor line now carried under the Silicon Labs brand. An SAR (Successive Approximation Register) ADC is a type of data converter that uses a binary-search algorithm against an internal DAC to digitize an analog input in N conversion clock cycles. SAR ADCs sit in the data converter hierarchy between flash converters (fast, expensive, low resolution) and sigma-delta converters (high resolution, slow, dense digital filtering). Because SAR ADCs require no continuous-time oversampling, they are well suited to multiplexed multi-channel acquisition systems, instrumentation loops, and embedded sensor readouts where deterministic latency matters more than extreme dynamic range. Key features include 300 ksps sampling rate, single 2.7 V to 3.6 V supply operation, internal 2.5 V reference, low power consumption, and a serial interface. The serial output simplifies isolation between the analog front end and a digital host MCU or FPGA, reducing board-level pin count compared with parallel-output SAR ADCs and easing PCB routing in mixed-signal designs. The TSM1285BCSA+ uses a charge-redistribution SAR architecture with an internal reference, internal offset calibration, and internal reference-error nulling per the manufacturer datasheet. After full-scale calibration, relative accuracy is specified against the theoretical code transfer function, supporting reliable closed-loop control and instrumentation applications where absolute transfer linearity matters. Typical applications include portable data acquisition systems, industrial process control loops, isolated sensor front ends, motor control current/voltage sense channels, and battery-powered instrumentation. The 2nd-source SOIC-8 footprint and commercial-grade temperature rating make it a flexible part for cost-sensitive mixed-signal designs. When designing with this ADC, ensure the analog input bandwidth does not exceed the device's -3 dB front-end limit; place a small RC anti-alias filter ahead of AIN. Decouple VDD with both bulk and 100 nF ceramic capacitance placed within 5 mm of the supply pin. This page synthesizes distributor pricing, drop-in same-package alternatives, and practical design notes not found in the manufacturer datasheet, enabling faster part-selection decisions.

询价 联系我们
TSM1285BCSA+T - 12-Bit 300ksps SAR ADC w/ 2.5V Ref | Silicon Labs
TSM1285BCSA+T

TSM1285BCSA+T - 12-Bit 300ksps SAR ADC w/ 2.5V Ref | Silicon Labs

The Silicon Labs TSM1285BCSA+T is a 12-bit, 300 ksps successive-approximation analog-to-digital converter (SAR ADC) with an internal +2.5 V reference, integrated track-and-hold, and a high-speed serial digital interface, packaged in an 8-pin SOIC (0.154 inch / 3.90 mm body width). It operates from a single +2.7 V to +3.6 V supply and draws less than 2.5 mA at full 300 ksps throughput. The device accepts single-ended analog inputs in the 0 V to VREF range, where VREF can be the internal 2.5 V source or an external reference up to AVDD. A SAR ADC is a precision data-acquisition converter that uses a binary search algorithm and an internal capacitive DAC to compare the sampled input against a reference voltage. It is a sub-category of analog-to-digital converters (ADC), itself a subclass of data-converter ICs within mixed-signal semiconductor devices. SAR ADCs are valued for their deterministic latency (no pipeline delay), low power consumption, and excellent DC accuracy, making them the standard choice for multiplexed data-acquisition systems, instrumentation, and sensor signal chains. Key features include ±1 LSB INL (max) typical linearity, an internal track-and-hold capable of handling input bandwidths up to several MHz, a low conversion-mode power dissipation below 2.5 mA, and a power-down mode that drops quiescent current to microamp levels for battery-powered designs. The serial interface is SPI-/QSPI-/MICROWIRE-compatible, allowing direct connection to most microcontrollers and DSPs without glue logic. Architecturally, the TSM1285BCSA+T combines a high-bandwidth track-and-hold, a charge-redistribution SAR core clocked from an internal oscillator, a low-drift buried-Zener reference (trimmed to ±2%), and a low-noise input buffer. The integrated reference removes a common BOM line, saving PCB area and lowering system cost in precision designs. Typical applications include portable instrumentation and data loggers, pen-digitizers and tablet input systems, loop-powered 4-20 mA sensor digitizers, factory-automation sensor front ends, and battery-monitoring modules for portable equipment. Designers should note that the SHDN pin must be driven logic-high for normal conversion and pulled logic-low for power-down. The internal reference output (REF) requires a 2.2 µF minimum bypass capacitor; values lower than this degrade linearity. Input signals must remain within 0 V to VREF to avoid saturation. This page synthesizes distributor pricing, pin-compatible drop-in alternatives including the Maxim MAX1285BCSA family, and practical design notes that are not consolidated in the manufacturer datasheet, supporting faster component evaluation.

询价 联系我们
TSM1285BESA+ - 12-Bit 300ksps SAR ADC | Silicon Labs SOIC-8
TSM1285BESA+

TSM1285BESA+ - 12-Bit 300ksps SAR ADC | Silicon Labs SOIC-8

The Silicon Labs TSM1285BESA+ (originally Touchstone Semiconductor) is a 12-bit, 300 ksps successive-approximation analog-to-digital converter in an 8-pin SOIC package, featuring an internal 2.5 V reference and a serial SPI/QSPI/MICROWIRE-compatible interface. The single-channel, single-ended input converter targets low-power, single-supply data-acquisition applications, including industrial instrumentation, process control, and portable sensor readout. The SAR (Successive Approximation Register) architecture is a class of ADC that performs bit-by-bit comparison using an internal DAC and a comparator, achieving deterministic conversion latency and excellent DC accuracy at moderate sampling rates compared with delta-sigma (which trades speed for higher oversampling resolution) or pipeline ADCs (which need higher clock speeds and consume more power). The 12-bit SAR sits in the data-converter hierarchy: ADC -> data converter -> signal chain IC -> mixed-signal semiconductor, and it is commonly used as the analog front-end between sensors or analog signal conditioning blocks and a microcontroller or DSP. Key features include 300 ksps maximum sampling rate, an internal 2.5 V reference (eliminating an external reference IC and saving PCB area), single 4.5 V to 5.5 V analog supply, low power dissipation suitable for battery and loop-powered systems, software-configurable unipolar/bipolar input range via the reference, and a flexible serial interface that supports SPI, QSPI, and MICROWIRE. The 8-SOIC surface-mount package keeps the part compact for high-density data-acquisition boards. The internal 2.5 V reference is trimmed during manufacture and provides the conversion full-scale; this removes one component from the BOM and simplifies factory calibration. The serial interface reduces pin count (no parallel data bus), enabling direct connection to microcontrollers and DSPs without glue logic, and the wide analog supply tolerance allows operation directly from a regulated 5 V rail or a low-dropout linear regulator output. Typical applications include industrial process control loops, weigh scales, panel meters, temperature and pressure sensor digitizers, portable medical instrumentation, and battery monitoring. The 12-bit resolution suits sensor linearization, threshold detection, and slow closed-loop control, while the 300 ksps rate handles audio-bandwidth and motor-control analog channels. When designing with this device, ensure the analog input does not exceed VDD; add a small RC anti-alias filter ahead of the input pin to limit noise above 150 kHz (half the Nyquist rate). Decouple VDD with a 10 uF tantalum plus 0.1 uF ceramic pair placed within 10 mm of the pin. This page synthesizes distributor pricing, drop-in cross-references (MAX1285BESA from Maxim Integrated is a pin-compatible functional twin in the same SOIC-8 footprint), and practical design notes not found in the manufacturer datasheet alone.

询价 联系我们
TSM1285BESA+T - 12-Bit 300ksps SAR ADC w/ Int Ref | Silicon Labs
TSM1285BESA+T

TSM1285BESA+T - 12-Bit 300ksps SAR ADC w/ Int Ref | Silicon Labs

The Silicon Labs TSM1285BESA+T is a 12-bit, 300 ksps successive-approximation analog-to-digital converter with an internal 2.5 V reference, offered in an 8-pin SOIC (SO) package. It provides one single-ended input channel, a serial (SPI/QSPI/MICROWIRE-compatible) interface, and operates from a single 2.7 V to 3.6 V analog and digital supply, drawing approximately 1 mA at full sampling rate. The integrated reference eliminates the need for an external precision reference, reducing BOM cost and board area in space-constrained designs. An SAR (Successive Approximation Register) ADC is a type of analog-to-digital converter that uses a binary-search algorithm against an internal or external reference to digitize an input voltage in N clock cycles, producing one sample per conversion with deterministic latency. ADCs sit within the broader data-acquisition signal chain (sensor -> front-end amplifier -> ADC -> microcontroller/DSP) and serve as the bridge between the analog physical world and digital signal processing. Low-power, single-supply 12-bit SAR ADCs like the TSM1285 are widely deployed in industrial sensors, instrumentation, and embedded monitoring. Key features include 12-bit resolution with no missing codes, a 300 ksps maximum sampling rate, an internal 2.5 V reference, a single-ended analog input, and an SPI-compatible serial output. The device delivers typical INL of +/-1 LSB and operates from -40C to +85C, making it suitable for industrial temperature environments. Low power consumption (~1 mA at 300 ksps) and a power-down mode that reduces current to nanoamp levels enable battery-powered and energy-harvesting applications. Architecturally, the TSM1285 uses a charge-redistribution SAR core with an integrated track-and-hold, a precision bandgap reference, and a serial output shift register. The internal reference is trimmed during manufacture, eliminating external trim components. The serial interface supports SPI, QSPI, and MICROWIRE modes, allowing direct connection to most microcontrollers without glue logic. Conversion is initiated via a chip-select falling edge and the result is clocked out on subsequent SCLK rising edges. Typical applications include industrial process control loop monitoring, portable battery-powered instrumentation, data-acquisition front-ends for sensor signals (temperature, pressure, strain), and embedded control systems. The internal reference simplifies designs that previously required an external reference plus a buffer amplifier. When designing with this part, place a 1 nF to 10 nF ceramic bypass capacitor as close as possible to the VDD pin and a 10 uF bulk capacitor at the supply input. Maintain a quiet analog ground return path; do not share the analog ground return with noisy digital currents. The reference decoupling capacitor (typically 4.7 uF on REF) is critical for AC performance. This page synthesizes distributor pricing, drop-in alternatives (same-brand MAX1285 family first, then cross-brand equivalents), and practical design notes not consolidated in the manufacturer datasheet.

询价 联系我们