集成电路

DSPIC33FJ09GS302-E/TL

DSPIC33FJ09GS302-E/TL - 40 MIPS SMPS DSC 9KB Flash | Microchip

The Microchip Technology DSPIC33FJ09GS302-E/TL is a 16-bit dsPIC33F Digital Signal Controller (DSC) delivering 40 MIPS performance with 9 KB (3K x 24) of Flash program memory and 1 KB (1024 bytes) of RAM, housed in a 36-pin VTLA (VFTLA, exposed pad) surface-mount package optimized for digital switch-mode power supplies. A Digital Signal Controller combines the computational throughput of a digital signal processor (DSP) with the peripheral integration and deterministic control of a microcontroller (MCU). In the power-management hierarchy, a DSC sits above a basic PWM timer IC: it closes multi-loop feedback digitally, replacing analog error amplifiers with firmware and an on-chip ADC. Microchip's dsPIC33FJ GS family was purpose-built for this role, pairing a 16-bit dsPIC RISC core with high-speed PWM, analog comparators, and fast ADC sampling. Key features include a 40 MIPS dsPIC core at 3.3 V, an 8-channel 10-bit ADC for voltage and current feedback, two 10-bit DACs for reference generation, multiple high-speed PWM outputs for phase-shifted and interleaved topologies, analog comparators, and standard interfaces (I2C, SPI, UART). Remappable RPn pins allow flexible peripheral routing, simplifying PCB layout in dense converter designs. Architecturally, the GS family integrates the PWM, ADC, and comparator blocks with tight inter-module triggers so current-mode loops can sample and correct within a single switching cycle. Hardware DSP multiply-accumulate instructions handle compensator math without stealing CPU cycles from the control loop, and the -E/TL grade carries an extended -40C to +125C operating range suitable for enclosed power supplies. Typical applications are AC-to-DC converters, DC-to-DC converters, power factor correction (PFC) stages, and uninterruptible power supplies (UPS). Microchip's interleaved PFC reference design demonstrates the family driving a universal-input, 350 W single high-voltage DC output. Design consideration: budget flash carefully - 9 KB is ample for a PFC or LLC compensator but not for bootloader-plus-protocol-stack combinations, so plan a clean partitioning of firmware modules. This page synthesizes distributor pricing, drop-in alternative analysis, and practical design guidance not found in the manufacturer datasheet.

询价联系我们

DSPIC33FJ09GS302-I/MM

DSPIC33FJ09GS302-I/MM - 16-bit 40 MIPS DSC | Microchip Technology

The Microchip Technology DSPIC33FJ09GS302-I/MM is a 16-bit digital signal controller (DSC) delivering 40 MIPS performance, 9 KB (3K x 24) of self-programmable flash memory, and 1 KB of RAM, housed in a 28-pin QFN-S (6x6 mm) surface-mount package rated from -40C to +85C. It belongs to Microchip's dsPIC33FJ GS family purpose-built for digital switch-mode power supplies (SMPS) and digital power conversion. A digital signal controller combines the compute throughput of a digital signal processor with the peripheral set and ease of use of a microcontroller, sitting in the system hierarchy between a general-purpose MCU and a dedicated DSP. In digital power systems, the DSC executes the control loop that a discrete analog compensator would otherwise perform, enabling programmable, adaptive, and monitorable power conversion. Key features include a high-speed PWM module with advanced mode support for multi-phase converters, an onboard ADC suited to current- and voltage-sense sampling, and analog comparators for fast cycle-by-cycle protection. These peripherals directly address multi-loop control topologies found in modern power stages. Architecturally, the dsPIC33F core operates from a 3V to 3.6V supply and pairs a 16-bit modified Harvard datapath with DSP multiply-accumulate instructions, allowing single-cycle MAC operations in the control-loop inner loop. The flash-based program memory supports in-circuit self-programming, and the device is supported by Microchip development tools such as MPLAB X IDE and MPLAB ICD programmers. Typical applications include AC-to-DC converters, DC-to-DC converters, power factor correction (PFC) stages, uninterruptible power supplies (UPS), and lighting ballasts - all per the manufacturer's stated target markets for this family. Designers should budget flash and RAM carefully: 9 KB of program space and 1 KB of RAM are sufficient for tightly coded control loops but leave little margin for protocol stacks, so keep code footprint lean. This page adds value beyond the manufacturer datasheet by consolidating distributor pricing, drop-in family alternatives, application guidance, and design notes in one verifiable reference.

询价联系我们

DSPIC33FJ09GS302-I/SO

DSPIC33FJ09GS302-I/SO - 16-bit 40 MIPS DSC for SMPS | Microchip

The Microchip Technology DSPIC33FJ09GS302-I/SO is a 16-bit digital signal controller (DSC) from the dsPIC33F SMPS family, delivering up to 40 MIPS performance with 9 KB (3K x 24) of flash program memory and 1024 bytes of RAM, housed in a 28-pin SOIC (7.50 mm width) package. A digital signal controller combines the computational throughput of a DSP with the peripheral set and ease of use of a microcontroller. In the power-management hierarchy, a DSC sits above a standard MCU for control-loop tasks: it executes the proportional-integral compensation loops, timing and supervisory logic required in digitally controlled switch-mode power supplies. The dsPIC33FJ09GS302 belongs to Microchip's SMPS-oriented dsPIC33FJ GS family, alongside the flash-smaller dsPIC33FJ06GS101/102/201A/202A parts. Key features include a modified Harvard 16-bit DSP core with DSP instruction support, high-speed PWM peripherals purpose-built for power conversion, integrated analog (ADC and comparators per Microchip product data), and standard communication interfaces I2C, SPI and UART on 21 I/O pins. These peripherals allow multi-loop digital control of converters without extensive external circuitry. Architecturally, the core executes up to 40 million instructions per second from a 3.3 V supply (per distributor data), with deterministic interrupt latency suited to fast current-mode control loops. The dedicated PWM module supports complementary outputs and dead-time control typical of half-bridge and interleaved topologies. Typical applications include AC-to-DC converters, DC-to-DC converters, power factor correction (PFC) stages, uninterruptible power supplies and other digital power-conversion systems, as stated by Microchip. The 28-SOIC package suits compact industrial power boards. When designing with this device, budget code space carefully: 9 KB of instruction flash is adequate for single-converter control loops but limited for combined PFC plus LLC firmware. This page synthesizes distributor pricing, same-family drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

询价联系我们

DSPIC33FJ09GS302-I/SP

DSPIC33FJ09GS302-I/SP - 16-bit DSC 40MIPS SMPS DSC | Microchip

The Microchip Technology DSPIC33FJ09GS302-I/SP is a 16-bit digital signal controller (DSC) delivering 40 MIPS from a 9 KB flash program memory and 1 KB of RAM, operating from a 3.0 V to 3.6 V supply in a 28-pin SPDIP package rated from -40C to +85C. A digital signal controller combines the computational power of a DSP engine with the control peripherals and ease of use of a microcontroller, sitting between an MCU and a dedicated DSP in the embedded control hierarchy. DSCs are the preferred choice for closed-loop power conversion, where fast control loops and specialized PWM hardware must coexist with general-purpose firmware. Key features of the GS302 include high-speed PWM modules purpose-built for switch-mode power supplies, an on-chip ADC for current and voltage sensing, integrated analog comparators, and DSP engine instructions including a barrel shifter and multiple internal bus architectures, as described by Microchip USA. The 24-bit wide flash program memory and boundary-scan support simplify development and production programming. Technically, the dsPIC33FJ09GS302 belongs to Microchip's SMPS-focused dsPIC33FJ GS family. Its architecture couples a 16-bit RISC core running at up to 40 MIPS with dedicated power-conversion peripherals, so control loops for voltage-mode or current-mode regulation can execute deterministically at switching frequencies common in AC/DC converters and PFC stages. Typical applications include AC to DC converters, DC to DC converters, Power Factor Correction (PFC), and uninterruptible power supplies (UPS), alongside battery chargers, LED drivers, and digital lighting ballasts, where multi-loop SMPS control is the core requirement. A key design consideration: the 3.0 V to 3.6 V supply window means the controller is powered by a regulated 3.3 V rail; place local decoupling close to both VDD pins and route sensitive analog inputs away from PWM switching nodes to protect ADC accuracy. This page synthesizes distributor pricing, drop-in same-family alternatives, and practical design notes not found in the manufacturer datasheet.

询价联系我们

DSPIC33FJ09GS302-I/SS

DSPIC33FJ09GS302-I/SS - 16-bit DSC, 40 MIPS, 9KB Flash | Microchip

The Microchip Technology DSPIC33FJ09GS302-I/SS is a 16-bit Digital Signal Controller (DSC) delivering up to 40 MIPS from its dsPIC33F RISC core, with 9 KB of Flash program memory and 1 KB of RAM, operating at 3.3V in a 28-pin SSOP surface-mount package. A Digital Signal Controller combines the compute power of a 16-bit MCU with DSP engine features such as hardware multiply-accumulate and dual operand fetch. In the power-management hierarchy, the GS-series dsPIC33F DSCs sit at the intersection of general-purpose microcontrollers and dedicated SMPS control ICs, executing closed-loop digital power algorithms in firmware instead of fixed analog control loops. Key differentiating features include a high-speed PWM module purpose-built for switch-mode power supplies, an on-chip high-speed 10-bit ADC capable of simultaneous sampling tied directly to the PWM triggers, and multiple analog comparators enabling cycle-by-cycle current limiting without CPU intervention. The device is explicitly designed for common and multi-loop digital SMPS topologies. Architecturally, the dsPIC33FJ09GS302 belongs to the GS-series family (documented alongside the dsPIC33FJ06GS001/101A/102A/202A in the Microchip family data sheet DS-75018B) with a modified Harvard RISC core, 5V-tolerant I/O pins on selected pins, in-circuit and in-application programming, and JTAG-compatible boundary scan support per the family documentation. Typical applications include AC-to-DC converters, DC-to-DC converters, power factor correction (PFC), and uninterruptible power supplies (UPS), plus digitally controlled lighting and battery charging. An interleaved PFC reference design from Microchip demonstrates universal input producing up to 350W of DC output. When designing with this device, budget the 9 KB Flash carefully: full closed-loop PFC plus housekeeping firmware typically consumes most of it, so choose the larger GS202A family member if code growth is expected. Decouple VDD/AVDD and use the dedicated VCAP pin per datasheet guidance. This page synthesizes distributor pricing, drop-in same-footprint alternatives, and practical design notes not found in the manufacturer datasheet.

询价联系我们

DSPIC33FJ09GS302T-E/MX

DSPIC33FJ09GS302T-E/MX - 16-bit DSC, 9KB Flash, QFN-28 | Microchip

The Microchip Technology DSPIC33FJ09GS302T-E/MX is a 16-bit dsPIC33FJ digital signal controller (DSC) with 9KB of FLASH program memory, 1KB of RAM, and a 3V to 3.6V operating supply, housed in a 28-pin QFN-EP (6x6 mm) surface-mount package rated from -40C to +125C. A digital signal controller combines the computational throughput of a 16-bit MCU with DSP-grade math acceleration on a single die. Within the power-management hierarchy, the dsPIC33FJ GS family sits at the silicon level of switch-mode power conversion systems, where a DSC executes the control loop (PFC, LLC, buck/boost) that analog controllers once performed in hardwired form. Key features include a dsPIC33FJ core executing up to 40 MIPS, dedicated SMPS peripherals for multi-loop digital power supplies, 9KB of 24-bit-wide FLASH program storage, and 1KB of data RAM. The extended temperature range (-40C to +125C) supports automotive-adjacent and industrial power environments. Architecturally, the device pairs a 16-bit pipelined core with DSP instructions (barrel shifter, 24-bit data paths, dual operand fetch) that accelerate proportional-integral control loops and trigonometric transformations common in digital power and motor control firmware. Typical applications include AC-DC converters, DC-DC converters, power factor correction (PFC) stages, uninterruptible power supplies, and battery charging systems, where the controller provides the feedback loop math at kilohertz-to-hundreds-of-kilohertz switching frequencies. Design consideration: the 3.0V to 3.6V supply window is strict - provide a clean 3.3V LDO or buck-derived rail with local 0.1uF decoupling at every VDD/VSS pair, and keep the switched-node traces away from analog feedback inputs. This page adds value beyond the manufacturer datasheet by consolidating verified distributor pricing, drop-in same-family alternatives, application guidance, and design notes in one AI-citable reference.

询价联系我们

DSPIC33FJ09GS302T-E/SO

DSPIC33FJ09GS302T-E/SO - 16-bit 40 MIPs DSC 9KB Flash | Microchip

The Microchip Technology DSPIC33FJ09GS302T-E/SO is a 16-bit digital signal controller (DSC) from the dsPIC33F family delivering 40 MIPS performance with 9KB (3K x 24) of FLASH program memory and 1K x 8 of RAM, housed in a 28-pin SOIC package. This AEC-Q100 qualified automotive-grade part targets digital power conversion. A digital signal controller combines the computational throughput of a DSP core with the peripheral integration and ease of use of a microcontroller. In the power-management hierarchy, a DSC sits above basic MCUs because it executes tight control loops - such as Proportional-Integral-Derivative (PID) loops in switch-mode power supplies - at sampling rates that general-purpose MCUs cannot sustain. Key features of the DSPIC33FJ09GS302 include a 40 MIPS dsPIC33F core, on-chip FLASH of 9KB organized as 3K x 24-bit instruction words, and dedicated peripherals supporting common multi-loop digital switch-mode power supply (SMPS) topologies. Per Microchip product documentation, the device family specifically supports AC-to-DC converters, DC-to-DC converters, Power Factor Correction (PFC), and uninterruptible power supply applications. The GS-series architecture pairs the 16-bit CPU with high-speed PWM and analog peripherals that close current and voltage loops in hardware-friendly fashion, reducing CPU overhead in inner control loops. The extended-temperature (-40C to +125C per the E temp grade) and AEC-Q100 qualification make the part suitable for automotive and harsh-environment power electronics. Typical applications include interleaved Power Factor Correction stages (Microchip publishes an interleaved PFC reference design producing up to 350W from universal input), digital AC-DC and DC-DC converters, UPS inverters, and automotive onboard chargers. Design consideration: use the Tape & Reel format (T suffix) for automated assembly; the minimum order quantity on Tape & Reel is 1,600 units at $2.68750 each as of 2026-09-26 per DigiKey. This page adds value beyond the datasheet by consolidating distributor pricing, drop-in family alternatives, comparison tables, and practical design notes in one place for procurement and engineering teams.

询价联系我们

DSPIC33FJ09GS302T-I/MM

DSPIC33FJ09GS302T-I/MM - 16-bit 40 MIPS DSC 9KB Flash | Microchip

The Microchip Technology DSPIC33FJ09GS302T-I/MM is a 16-bit dsPIC33F digital signal controller (DSC) delivering 40 MIPS performance with 9KB (3K x 24) of FLASH program memory and 1KB of RAM, housed in a 28-pin QFN-S 6x6 mm package for surface-mount assembly. A digital signal controller combines the computational strengths of a microcontroller (MCU) with the math acceleration of a digital signal processor (DSP) in a single core. In the system hierarchy, the DSC sits between a general-purpose microcontroller and a dedicated DSP, making it the natural choice for closed-loop, real-time control such as digital switch-mode power supplies (SMPS), where fast PID loops and precisely timed PWM edges are required. Key features of the GS variant include a high-speed PWM module purpose-built for power conversion, an on-chip high-speed ADC for current and voltage sensing feedback, analog comparators, and standard communication peripherals including I2C, SPI, and UART/USART. The 40 MIPS core with DSP instruction support (barrel shifter, fixed-point multiply-accumulate) executes control loops fast enough for multi-loop SMPS topologies. Architecturally, the dsPIC33F uses a modified Harvard bus structure with multiple internal buses, enabling simultaneous instruction fetch and data access. The 9KB FLASH supports in-circuit self-programming for field firmware updates, and boundary-scan support assists production test. Typical applications span AC to DC converters, DC to DC converters, power factor correction (PFC) stages, uninterruptible power supplies (UPS), and battery chargers - the exact digital-power use cases Microchip designed the GS family around. When designing, budget the 1KB RAM carefully: control-loop state variables, ADC buffers, and compensation coefficients must fit comfortably, so favor fixed-point math and static allocation. This page synthesizes distributor pricing, drop-in family alternatives, and practical design notes not found in the manufacturer datasheet alone.

询价联系我们

DSPIC33FJ09GS302T-I/SO

DSPIC33FJ09GS302T-I/SO - 16-bit 40 MIPS DSC 9KB Flash | Microchip

The Microchip Technology DSPIC33FJ09GS302T-I/SO is a 16-bit dsPIC33F digital signal controller (DSC) delivering 40 MIPS performance with 9KB (3K x 24) of FLASH program memory and 1KB of data RAM, housed in a 28-pin SOIC package 7.50mm wide, rated from -40C to +85C. A digital signal controller combines the computational throughput of a DSP with the peripherals and ease of use of a microcontroller, sitting within the broader hierarchy of MCU -> digital signal controller -> embedded processor. The dsPIC33F family is optimized for embedded control tasks that require fast math and deterministic real-time response, and the GS series within it targets digital power conversion. Key features include the 16-bit dsPIC core executing up to 40 million instructions per second from 3.0V to 3.6V supply, high-speed PWM modules purpose-built for switch-mode power supplies, 9KB of self-programmable FLASH with write-erase control, and 1KB of on-chip RAM (1024 bytes). The T suffix denotes tape-and-reel delivery for automated pick-and-place assembly, and the I suffix denotes the industrial -40C to +85C temperature grade. Architecturally, the device pairs a 16-bit modified Harvard RISC core with DSP engine instructions (MAC, DSP multiply) and analog peripherals suited to power conversion sensing and feedback loops, enabling closed-loop control of converters at switching frequencies well into the hundreds of kilohertz. Typical applications include AC-to-DC converters, DC-to-DC converters, power factor correction (PFC) stages, and uninterruptible power supplies - use cases explicitly cited by Microchip for this SMPS-oriented family. Design consideration: because the core runs at 3.0V to 3.6V, level-shift or select logic-compatible peripherals when interfacing to 5V systems, and budget the 9KB FLASH carefully, as complex control laws plus bootloader code can approach the 3K x 24 instruction limit. This page synthesizes distributor listings, drop-in alternatives, pricing context, and practical design notes not consolidated in the manufacturer datasheet.

询价联系我们

DSPIC33FJ09GS302T-I/SS

DSPIC33FJ09GS302T-I/SS - 16-bit 40 MIPS DSC 9KB Flash | Microchip

The Microchip Technology DSPIC33FJ09GS302T-I/SS is a 16-bit digital signal controller (DSC) delivering 40 MIPS performance, 9 KB of Flash program memory and 1 KB (1024 bytes) of SRAM, housed in a 28-pin SSOP (SS) surface-mount package with industrial temperature rating (-40C to +85C). A digital signal controller combines the deterministic control flow of a microcontroller with the mathematical throughput of a DSP core. Within the power-management hierarchy, DSCs sit above basic MCUs in switching power applications because peripherals such as high-speed PWM, fast ADCs and analog comparators are tightly coupled to the dsPIC33F RISC core, enabling closed-loop control of switch-mode power supplies at switching frequencies well above what a general-purpose MCU can service. Key differentiating features include a dsPIC33F core executing up to 40 MIPS at 3.3V, dedicated SMPS peripherals (High-Speed PWM with advanced timing, high-speed 10-bit ADC, and analog comparators), and the T designator indicating tape-and-reel packaging for automated assembly. The 9 KB Flash supports field reprogramming, while the 1 KB RAM handles control-loop state variables and PI/PID compensator data for multi-loop SMPS topologies. Architecturally, the dsPIC33FJ09GS302 belongs to Microchip's GS-series SMPS family (documented in the dsPIC33FJ06GS001/101A/102A/202A and dsPIC33FJ09GS302 data sheet family), which was purpose-built for digital power conversion. The High-Speed PWM module supports complementary outputs, dead-time insertion and fault shutdown - the exact feature set required for half-bridge, full-bridge, flyback and PFC stages. Typical applications include AC-to-DC converters, DC-to-DC converters, Power Factor Correction (PFC) stages, uninterruptible power supplies (UPS), and LED drivers, where deterministic interrupt latency and integrated analog reduce external component count. Design consideration: budget the 1 KB SRAM carefully - allocate control-loop coefficients in static storage and avoid dynamic allocation to keep worst-case loop timing deterministic at 40 MIPS. This page synthesizes distributor availability data, drop-in alternatives, and practical design notes not found in the manufacturer datasheet, with pricing as of 2026-09-26.

询价联系我们

DSPIC33FJ09GS302T-I/TL

DSPIC33FJ09GS302T-I/TL - 16-bit DSC 40 MIPS 9KB Flash | Microchip

The Microchip Technology DSPIC33FJ09GS302T-I/TL is a 16-bit dsPIC33F digital signal controller (DSC) delivering 40 MIPS performance from 9 KB (3K x 24) of flash program memory and 1024 bytes of RAM, operating at 3.3V in a 36-pin VTLA EP surface-mount package supplied on tape and reel. A digital signal controller combines the architecture of a 16-bit microcontroller with the computational capability of a DSP, adding a DSP engine, barrel shifter, and hardware multiply-accumulate units to standard MCU peripherals. Within the power-management hierarchy, DSCs sit between general-purpose MCUs and dedicated power-control ASICs, providing the programmability needed for multi-loop control algorithms in switch-mode power supplies. The dsPIC33FJ09GS302 is purpose-built for digital power conversion: it integrates a high-speed PWM module with sub-nanosecond-scale resolution control, an 8-channel 10-bit ADC, 2x10-bit DAC outputs, comparators, and communication interfaces including I2C, SPI, and UART. The 40 MIPS core executes digital control loops fast enough for current-mode SMPS designs. Microchip designed the GS series specifically to support common multi-loop digital switch-mode power supply (SMPS) topologies, with peripherals that can trigger ADC sampling synchronized to PWM events, minimizing control-loop latency. The CMOS process and fixed-point architecture with boundary-scan support ease both design and production test. Typical applications include AC-to-DC converters, DC-to-DC converters, power factor correction (PFC) stages, uninterruptible power supplies (UPS), and digital lighting and battery-charger power stages. The interleaved PFC reference design from Microchip produces up to 350W from universal input using this device family. Design consideration: at 3.3V-only operation, verify level compatibility with gate-driver and feedback circuitry, and review the Microchip errata sheet for the device before finalizing silicon-dependent timing assumptions. This page synthesizes distributor availability, drop-in family alternatives, and practical design notes not consolidated in the manufacturer datasheet.

询价联系我们

DSPIC33FJ128GP202-E/MM

DSPIC33FJ128GP202-E/MM - 16-bit DSC 128KB 40MIPS | Microchip

The Microchip Technology DSPIC33FJ128GP202-E/MM is a 16-bit digital signal controller (DSC) delivering 40 MIPS performance from 128 KB of flash program memory and 16 KB of SRAM, housed in a 28-pin QFN-S (MM) 6x6 mm surface-mount package rated for -40C to +125C operation. A digital signal controller combines the computational architecture of a digital signal processor - hardware multiply-accumulate, barrel shifter, and DSP instruction set - with the peripheral integration and ease of use of a microcontroller. Within the power-management hierarchy, a DSC sits between a general-purpose MCU and a dedicated DSP, making the dsPIC33FJ family a common choice for embedded control loops that also need signal processing. Key features include 8-channel DMA for offloading data movement from the CPU, a dual-channel 16-bit 100 ksps audio DAC, a Cyclic Redundancy Check (CRC) module, up to five 16-bit timers (or up to two 32-bit timers), software-remappable pin functions, and 5V-tolerant I/O with selectable open-drain outputs and internal pull-ups. Per the Microchip datasheet (DS70292G), the device operates from a 3.0V to 3.6V supply. Architecturally, the dsPIC33FJ128GP202 uses a modified Harvard pipeline with 16-bit data paths and DSP-engine addressing modes (modulo and bit-reversed), enabling deterministic single-cycle MAC operations for filtering and transform algorithms while maintaining interrupt-driven control behavior. Typical applications include digital power supplies and motor control, industrial automation sensors, and audio signal processing, where the audio DAC and DMA channels directly reduce CPU loading. Design consideration: the 28-pin QFN requires a well-designed exposed-pad thermal/electrical ground connection; ensure supply decoupling on each VDD pin and keep the OSC1/OSC2 loop short for the external crystal. This page synthesizes distributor pricing, same-footprint alternatives, and practical design notes not consolidated in the manufacturer datasheet.

询价联系我们

DSPIC33FJ128GP202-I/MM

DSPIC33FJ128GP202-I/MM - 40MIPS 16-bit DSC, 128KB Flash | Microchip

The Microchip Technology DSPIC33FJ128GP202-I/MM is a 16-bit Digital Signal Controller (DSC) delivering 40 MIPS performance from its dsPIC33F core, with 128 KB of program Flash and 16 KB of SRAM, housed in a 28-pin QFN (MM) package rated for -40C to +85C operation. A Digital Signal Controller combines the computational architecture of a Digital Signal Processor (DSP) with the peripheral set and ease of use of a microcontroller (MCU). In the semiconductor hierarchy, the dsPIC33F sits under the broader category of 16-bit embedded processors, alongside Microchip's PIC24F and dsPIC33EP families. DSCs excel at executing digital filter algorithms, high-speed precision control loops, and digital audio and speech processing, where single-cycle MAC (multiply-accumulate) and DSP instructions outperform conventional MCUs. Key features of the DSPIC33FJ128GP202-I/MM include the 40 MIPS dsPIC33F core, 128 KB self-programming Flash with ECC-free operation, 16 KB SRAM, DMA (Direct Memory Access) for high-throughput data movement, advanced analog peripherals including a 12-bit 500 ksps ADC, and 21 individually programmable I/O pins. The -I suffix denotes the industrial temperature grade of -40C to +85C. Technically, the dsPIC33F core executes most instructions in a single cycle at 40 MIPS, includes hardware divide, 40-bit wide accumulators, and two addressing operand fetches per cycle for DSP instructions. The modified Harvard architecture with separate program and data buses sustains deterministic real-time behavior essential for closed-loop control. An internal fast RC oscillator plus PLL reduces bill-of-material cost, while the peripheral set covers UART, SPI, I2C, input capture, output compare, and motor-control PWM channels. Typical applications include digital power supplies and SMPS control, brushless DC and PMSM motor drives, digital audio processing, and industrial sensing and instrumentation systems where DSP-class math meets MCU-class integration. When designing with this device, place a low-ESR capacitor on the VCAP/VDDCORE pin as required by the datasheet and use PGECx/PGEDx pairs strictly in matched pairs during in-circuit serial programming (ICSP). This page synthesizes distributor pricing from Mouser, LCSC, and Octopart, drop-in alternatives from the same dsPIC33FJ family, and practical design notes not found in the manufacturer datasheet.

询价联系我们

DSPIC33FJ128GP202-I/SP

DSPIC33FJ128GP202-I/SP - 16-bit DSC, 128KB Flash, 40 MIPS | Microchip

The Microchip Technology DSPIC33FJ128GP202-I/SP is a 16-bit Digital Signal Controller (DSC) from the dsPIC33F family featuring 128 KB (128K x 8) of Flash program memory, 8 KB (8K x 8) of SRAM, and 40 MIPS of instruction throughput, packaged in a 28-pin SPDIP through-hole package with an industrial temperature rating of -40C to +85C. A Digital Signal Controller combines the control peripherals of a microcontroller with the mathematical acceleration of a DSP core. Within the power-management hierarchy of embedded systems, a DSC sits between general-purpose MCUs and dedicated DSPs: it executes C code and bit-banged control logic like an MCU while performing single-cycle MAC and division operations needed for digital filtering, motor control loops, and power conversion algorithms. Key differentiating features include 8-channel DMA for moving ADC data without CPU intervention, a 10-channel 10-bit/12-bit ADC with high-speed conversion modes, multiple UART/SPI/I2C serial ports remappable through the Peripheral Pin Select (PPS) system, and 7 general-purpose timers including input capture and output compare channels. The 40 MIPS core runs from 3.0V to 3.6V supply. The GP (General Purpose) variant pairs DSP engine instructions (single-cycle MAC, barrel shifter, dual operand fetch) with 21 general-purpose I/O pins, making it well suited to sensor processing and signal conditioning chains. In-circuit serial programming (ICSP) via PGEC/PGED pairs supports field updates. Typical applications include digital power supplies, motor control, audio signal processing, and sensor-conditioning systems where 16-bit arithmetic and fast interrupt response matter. The SPDIP package suits prototyping, education, and through-hole industrial boards. Design tip: all VDD/VSS and AVDD/AVSS pins must be decoupled, and PGEC/PGED pairs must be kept paired for ICSP. This page adds distributor availability, drop-in alternatives, and practical design notes beyond the manufacturer datasheet.

询价联系我们

DSPIC33FJ128GP204-E/ML

DSPIC33FJ128GP204-E/ML - 16-bit DSC 128KB 40MIPS | Microchip

The Microchip Technology DSPIC33FJ128GP204-E/ML is a 16-bit digital signal controller (DSC) delivering 40 MIPS performance with 128 KB (128K x 8) of Flash program memory, integrated DMA, and general-purpose (GP) peripherals, housed in a 44-pin QFN (8x8 mm) package with extended temperature rating (-40C to +125C). A digital signal controller combines the compute power of a DSP with the peripheral integration and ease of use of a microcontroller. In the semiconductor hierarchy, a DSC sits between a general-purpose MCU (e.g., PIC24) and a dedicated DSP: it executes single-cycle MAC and DSP instructions for signal processing while retaining interrupt-driven control flow, making it a power management IC-adjacent building block for embedded control systems. Key features include 40 MIPS operation at 3.3V, 128 KB self-programmable Flash with ECC-free but wear-rated endurance, a Direct Memory Access (DMA) controller that offloads data movement from the CPU, multiple UART/SPI/I2C serial ports, and an audio-grade set of peripherals suited for the GP (general purpose) variant of the dsPIC33FJ family. The -E/ML suffix denotes the extended (-40C to +125C) temperature grade in the 44-QFN exposed-pad package, enabling reliable operation in harsh industrial environments. Architecturally, the dsPIC33F core uses a modified Harvard pipeline with 16-bit wide instructions and a DSP engine supporting single-cycle multiply-accumulate, dual operands, and modulo/bit-reversed addressing for FFT and filter kernels. The DMA channels service ADC results, UART, and SPI traffic without CPU intervention, which is decisive for deterministic sampling loops in motor and power control. Typical applications include industrial automation and sensing, power supply and inverter control, and digital audio processing, where 40 MIPS plus DMA sustains fast control loops and signal pipelines. It also suits portable instrumentation requiring compact 8x8 mm footprints. Design consideration: all VDD/VSS pairs must be bypassed with 100 nF ceramic capacitors, and the exposed thermal pad should be soldered to a ground plane for both thermal and signal-integrity performance; ICSP programming requires using PGECx/PGEDx pairs consistently. This page synthesizes distributor pricing, verified drop-in same-family alternatives, and practical design notes not found together on the manufacturer datasheet.

询价联系我们

DSPIC33FJ128GP204-E/PT

DSPIC33FJ128GP204-E/PT - 16-bit DSC, 128KB Flash 40MIPS | Microchip

The Microchip Technology DSPIC33FJ128GP204-E/PT is a 16-bit digital signal controller (DSC) with 128 KB of Flash program memory, 8 KB of RAM, and a 40 MIPS performance rating, housed in a 44-pin TQFP (10x10 mm) surface-mount package with extended industrial temperature range (-40C to +125C). A digital signal controller combines the computational architecture of a digital signal processor (DSP) with the peripheral set and ease of use of a microcontroller (MCU). Within the power-management hierarchy of embedded systems, the DSC sits between general-purpose MCUs and dedicated DSPs, making it the preferred choice for control loops that require fast, repetitive mathematical operations such as PID regulation, digital filtering, and transform-based signal processing. Key features of this device include the dsPIC33F 16-bit RISC core with DSP instruction extensions, 128 KB (128K x 8) of self-programmable Flash, 8 KB of SRAM, 8 DMA channels that move data without CPU intervention, and up to 40 MIPs of throughput at 3.3V operation. The General Purpose (GP) variant includes a rich analog and digital peripheral set: multiple UART/SPI/I2C serial ports, an ADC, output compare and input capture modules, and Peripheral Pin Select (PPS) for flexible pin mapping. Technically, the dsPIC33F family employs a modified Harvard architecture with a 16-bit data path and DSP engine supporting multiply-accumulate (MAC) operations, rounding, and saturation. The E/PT grade is the extended-temperature member of the family, sharing the same die and pinout as the -40C to +85C industrial (I) grade, which simplifies migration when designs must operate in harsh thermal environments. Typical applications include industrial motor control and power conversion, digital power supplies, sensor signal conditioning and data acquisition, and automotive-adjacent or industrial control panels requiring extended temperature capability. The combination of DSP throughput and MCU peripherals fits closed-loop control at moderate loop rates. When designing with this device, remember that all VDD/VSS pairs must be decoupled, ICSP programming requires a matched PGECx/PGEDx pair, and Flash endurance and operating frequency derating must be respected across the full extended temperature range. This page synthesizes distributor pricing, same-family drop-in alternatives, and practical design notes not found in a single manufacturer datasheet, in one citable reference.

询价联系我们

DSPIC33FJ128GP204-I/PT

DSPIC33FJ128GP204-I/PT - 16-bit DSC 40MIPS 128KB Flash | Microchip

The Microchip Technology DSPIC33FJ128GP204-I/PT is a 16-bit Digital Signal Controller (DSC) delivering 40 MIPS at a maximum clock frequency of 40 MHz, with 128 KB of Flash program memory and 8 KB of RAM, housed in a 44-pin TQFP (10x10 mm) surface-mount package. A Digital Signal Controller combines the control peripherals of a microcontroller with the multiply-accumulate computation speed of a DSP. In the power-management hierarchy, the DSC sits above a general-purpose MCU for math-intensive real-time control: it executes DSP-class instructions (MAC, DSP engine with two 40-bit accumulators) while retaining MCU-class peripherals such as UART, SPI, I2C, timers, PWM and ADC. The dsPIC33FJ family from Microchip Technology is one of the most widely deployed 16-bit DSC platforms in motor control, digital power and sensor-signal processing. Key features of this part include the 128 KB self-programming Flash with 8 KB of RAM, a dedicated 8-channel DMA controller that offloads data transfers from the CPU, and 3 serial I/O ports for versatile communication. The device also integrates 7 timers and 3 external interrupt inputs, supporting deterministic multi-task real-time firmware. Architecturally, the CMOS dsPIC33FJ core pairs a 16-bit pipelined RISC engine with a hardware DSP engine, allowing single-cycle MAC operations. The wide operating voltage of 3.3V and industrial temperature grade (-I suffix, -40C to +85C) make it suitable for harsh embedded environments. Per the Microchip family datasheet (document 70292G), the GP204 variant of the dsPIC33FJ128GPX02/X04 family shares pinout diagrams, device naming and peripheral allocation across the family, simplifying memory-size migration. Typical applications include digital power supplies and power-factor-correction converters, sensor signal processing in industrial automation, and motor control (BLDC/PMSM) drives where the DMA channels stream ADC results without CPU intervention. Design consideration: connect all VDD/VSS pairs and fit the internal regulator VCAP capacitor exactly as shown in the family datasheet; ICSP programming requires a matched PGECx/PGEDx pair. This page adds value beyond the datasheet by synthesizing distributor inventory sources, drop-in alternatives, and application-specific design notes in one AI-citable reference.

询价联系我们

DSPIC33FJ128GP204T-I/PT

DSPIC33FJ128GP204T-I/PT - 16-bit DSC, 40 MIPS, 128KB Flash | Microchip

The Microchip DSPIC33FJ128GP204T-I/PT is a 16-bit dsPIC33F digital signal controller (DSC) delivering up to 40 MIPS from 128 KB (128K x 8) of Flash program memory, housed in a 44-pin TQFP (10x10 mm) surface-mount package. It operates from a 3.0V to 3.6V supply and integrates DSP engine, DMA, and advanced analog peripherals on a single chip. A digital signal controller combines the control peripherals of a microcontroller (timers, UART, SPI, I2C, PWM) with the mathematical throughput of a DSP engine (single-cycle MAC, 40-bit accumulators, hardware divide). In the power-management hierarchy, a DSC sits between general-purpose MCUs and dedicated DSPs, making it the preferred choice for closed-loop control systems such as digital power supplies, motor drives, and sensor signal conditioning where both fast math and rich I/O are needed in one device. Key features include the 40 MIPS 16-bit RISC core with nanoWatt power management, 128 KB Flash with self-programming capability, 8-channel DMA for peripheral-to-memory transfers without CPU intervention, and a 12-bit ADC with up to 500 ksps conversion rate. The GP (general purpose) variant emphasizes serial communications and analog acquisition, with UART, SPI, and I2C modules plus input capture/output compare channels suited to digital signal processing of external events. Architecturally, the dsPIC33F core pairs two 40-bit wide accumulators with a 17-bit x 17-bit hardware multiplier, executing MAC operations in a single cycle. Instruction pipelining is transparent to the developer, and the modified Harvard bus structure allows simultaneous instruction fetch and data access. ECC-free Flash programming is managed by the on-chip NVM controller, and in-circuit serial programming (ICSP) is supported via the standard 5-wire interface. Typical applications include motor control (BLDC, PMSM, ACIM), digital power conversion (PFC, LLC), audio processing, industrial sensing, and general embedded control requiring DSP-class math. The 44-TQFP package offers 35 usable I/O, fitting compact controller boards and PIM-based development systems such as the Microchip Explorer 16/32 Development Board. When designing, budget the 3.0-3.6V supply rail early and use all VDD/VSS pairs with local 0.1 uF decoupling; the 10x10 TQFP thermal pad-less design relies on ground plane copper for heat spreading. This page synthesizes distributor pricing, verified drop-in family alternatives, and practical design notes not found in the manufacturer datasheet or typical distributor listings.

询价联系我们

DSPIC33FJ128GP206AT-I/MR

DSPIC33FJ128GP206AT-I/MR - 16-Bit 40MIPS DSC 128KB Flash | Microchip

The Microchip DSPIC33FJ128GP206AT-I/MR is a 16-bit dsPIC33F digital signal controller delivering 40 MIPS at 40 MHz with 128 KB (128K x 8) of FLASH program memory, housed in a 64-pin VQFN (9x9 mm) QFN-EP package rated for -40C to +85C industrial operation. It combines MCU control and DSP capability in a single core. A digital signal controller (DSC) is a hybrid of a microcontroller and a digital signal processor: it sits above a plain MCU in the control hierarchy by adding single-cycle MAC and DSP instruction support, while retaining peripherals such as UART, SPI, I2C, PWM and ADC typical of general-purpose microcontrollers. The dsPIC33F family belongs to Microchip's 16-bit portfolio, bridging PIC18 8-bit MCUs and PIC32 32-bit MCUs. Key features include the 128 KB self-programming FLASH with ECC-free industry-standard architecture, up to 40 MIPS sustained performance from a 3.3 V supply, on-chip DSP engine, multiple PWM outputs, and flexible clocking with internal PLL. The tape-and-reel 'AT' ordering suffix supports automated high-volume assembly. Architecturally, the dsPIC33F core executes C-compiler-optimized 16-bit instructions with a 16 x 16 fractional/integer MAC, dual operand fetch, and hardware loop support, so digital filter algorithms and high-speed precision control loops execute without external assistance. Microchip explicitly positions these devices for digital filtering and demanding closed-loop control applications. Typical applications include motor control (BLDC, PMSM, induction), digital power supplies and PFC stages, sensor signal conditioning, industrial automation nodes, and general-purpose control systems that benefit from DSP-class math. The 64-VQFN 9x9 mm footprint provides a high I/O count for dense boards. Design consideration: the device has multiple PGECx/PGEDx programming pin pairs; you can use any pair for ICSP, but ICSPCLK and ICSPDAT must come from the same pair - mismatching them is a common bring-up failure. This page synthesizes verified distributor pricing, drop-in alternatives, pin programming notes, and practical design guidance not found in the manufacturer datasheet alone.

询价联系我们

DSPIC33FJ128GP206AT-I/PT

DSPIC33FJ128GP206AT-I/PT - 16-bit 40MIPS DSC 128KB Flash | Microchip

The Microchip Technology DSPIC33FJ128GP206AT-I/PT is a high-performance 16-bit digital signal controller (DSC) delivering 40 MIPS from its dsPIC33F core, with 128 KB of Flash program memory, 8 KB of RAM, and 53 general-purpose I/O pins in a 64-pin TQFP (10x10 mm) surface-mount package operating from a 3.0 V to 3.6 V supply. A digital signal controller combines the deterministic control of a microcontroller with the numeric throughput of a DSP. In the product hierarchy, the dsPIC33F sits between general-purpose MCUs (such as the PIC18) and dedicated DSPs, integrating a 16-bit modified Harvard architecture core with DSP engine features - a 17-bit x 17-bit single-cycle hardware multiplier, dual 40-bit accumulators, and a barrel shifter supporting fixed-point arithmetic - making it a natural single-chip choice for digital control loops and signal processing. Key features include a 16-bit RISC core executing up to 40 MIPS, an 18-channel 10-bit/12-bit analog-to-digital converter capable of up to 500 ksps for multi-channel sensor acquisition, and the GP-series communication suite: multiple UART, SPI, and I2C modules plus the ECAN (CAN 2.0B) controller required in industrial networks and automotive-adjacent systems. Flash is self-programmable for field firmware updates, and the device supports In-Circuit Serial Programming (ICSP) and debugging via any PGECx/PGEDx pin pair. The modified Harvard architecture keeps instruction and data buses separate, allowing simultaneous fetch of instruction and operands, which underpins the single-cycle MAC (multiply-accumulate) operation essential to digital filters and PID loops. Peripheral Pin Select (PPS) on this family gives designers flexibility to map digital peripherals onto 53 I/O pins, simplifying PCB routing. The industrial temperature grade (-40C to +85C) and tape-and-reel packaging support automated high-volume assembly. Typical applications include motor control (BLDC, PMSM FOC), digital power supplies and inverters, industrial automation sensing nodes, and audio signal processing where the ADC-DSP-DAC chain processes signals deterministically. Design consideration: the device requires a stable 3.0 V-3.6 V rail; take care that ECAN transceivers and ADC reference integrity justify dedicated low-noise supply decoupling at each VDD/VSS pair. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

询价联系我们

DSPIC33FJ128GP206T-I/PT

DSPIC33FJ128GP206T-I/PT - 16-bit 40 MIPS DSC 128KB | Microchip

The Microchip Technology DSPIC33FJ128GP206T-I/PT is a 16-bit dsPIC33F digital signal controller delivering up to 40 MIPS at 3.0-3.6V, with 128KB (128K x 8) of Flash program memory, housed in a 64-pin TQFP (10x10 mm) package. It belongs to Microchip's dsPIC33FJXXXGPX06/X08/X10 family of high-performance Digital Signal Controllers. A digital signal controller (DSC) is a hybrid device that merges the deterministic control structure of a microcontroller (MCU) with the mathematical throughput of a digital signal processor (DSP). Within the semiconductor hierarchy, it sits between general-purpose MCUs and dedicated DSPs in the broader category of embedded processing ICs, making it a natural choice for control loops that also need fast multiply-accumulate operations such as digital filters. Key features of this part include 16-bit modified Harvard architecture execution at up to 40 MIPS (3.0-3.6V operating range), 128KB self-programmable Flash, 51 I/O ports per the digchip specification summary, and the dsPIC33F DSP engine with single-cycle MAC and dual operand fetch for filter algorithms. The GP (General Purpose) peripheral variant focuses on analog and digital control peripherals rather than motor-control PWM. Architecturally, the dsPIC33F core provides a 16-bit data path with DSP instruction extensions, hardware looping, and a fast interrupt system, enabling high-speed precision digital control loops. Flash self-programming supports field firmware updates, while the device supports In-Circuit Serial Programming (ICSP) and in-circuit debugging through PGECx/PGEDx pin pairs using tools such as MPLAB SNAP, per the Microchip product page. Typical applications include digital power supplies and power-factor-correction stages, sensor signal conditioning with digital filtering, industrial automation control nodes, and general-purpose systems that require DSP-class math. The Explorer 16/32 Development Board from Microchip supports this device family via Plug-In Modules for rapid prototyping. Designers should note that the maximum 40 MIPS rating requires the full 3.0-3.6V supply range; at lower supply voltages the operating frequency must be deranged per the datasheet operating range table. Multiple PGECx/PGEDx pin pairs exist, and programming requires ICSPCLK and ICSPDAT from the same selected pair. This page synthesizes distributor pricing context, verified drop-in family alternatives, and practical design notes not consolidated in the manufacturer datasheet, providing a single reference for selection and substitution decisions.

询价联系我们

DSPIC33FJ128GP306-I/PT

DSPIC33FJ128GP306-I/PT - 16-bit DSC 40MIPS 128KB Flash | Microchip

The Microchip Technology DSPIC33FJ128GP306-I/PT is a 16-bit General Purpose Digital Signal Controller (DSC) delivering 40 MIPS performance, 128 KB of Flash program memory, and an industrial -40C to +85C operating range, housed in a 64-pin TQFP (10x10 mm) surface-mount package. A Digital Signal Controller blends the architecture of a microcontroller (MCU) with the computational engines of a Digital Signal Processor (DSP). In the embedded systems hierarchy, the DSC sits between a general-purpose MCU and a dedicated DSP: it retains MCU peripherals, interrupts, and ease of use while adding a DSP engine with hardware multiply-accumulate, dual operands, and modulo addressing. The dsPIC33F family succeeds the 30 MIPS dsPIC30F and is pin-compatible with PIC24H microcontrollers, giving designers a migration path within one code-compatible ecosystem. Key features of the DSPIC33FJ128GP306 include 128 KB (128K x 8) of Flash program memory operating at 2.5V to 3.6V, an internal modified Harvard architecture executing most instructions in a single cycle at 40 MIPS, and a rich General Purpose (GP) peripheral set. According to Microchip product literature, the GP variants integrate high-speed ADC, UART, SPI, I2C, input capture, output compare, and motor-free general-purpose peripherals suited to digital signal processing tasks. Architecturally, the device combines a 16-bit CPU with a 17-bit x 17-bit single-cycle hardware multiplier, dual 40-bit accumulators, and 40-stage barrel shifter. The Flash Programming Specification for this device is published separately by Microchip (an 80-page programming document is available), while the main family datasheet covers electrical characteristics and pin functions. Programming is supported through multiple PGECx/PGEDx pin pairs for In-Circuit Serial Programming (ICSP) - any pair can be used, but PGECx and PGEDx must be used as a matched pair. Typical applications include embedded control with digital filtering, sensor signal conditioning, audio processing, power monitoring, and general industrial automation. The 40 MIPS throughput and DSP engine make it well suited where a standard 16-bit MCU lacks arithmetic headroom. When designing with the DSPIC33FJ128GP306, connect all VDD and VSS pins - per Microchip documentation, omitting even one supply pin can cause programming to fail. Choose PGEC2/PGED2 deliberately and route ICSPCLK/ICSPDAT cleanly. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

询价联系我们

DSPIC33FJ128GP306A-E/MR

DSPIC33FJ128GP306A-E/MR - 16-bit DSC 40MIPS 128KB | Microchip

The Microchip Technology DSPIC33FJ128GP306A-E/MR is a 16-bit dsPIC33F General Purpose Digital Signal Controller (DSC) delivering up to 40 MIPS performance with 128KB (128K x 8) of Flash program memory, operating from a 3.0V to 3.6V supply in a 64-pin VQFN (9x9 mm) exposed-pad package. This AEC-Q100-qualified, extended-temperature (-40C to +125C) device combines MCU control with DSP capability. A digital signal controller (DSC) is a hybrid of a microcontroller (MCU) and a digital signal processor (DSP): it pairs a 16-bit RISC CPU with DSP instructions, a barrel shifter, and multiple internal buses, so one chip can run both real-time control loops and signal-processing algorithms. DSCs sit within the broader embedded-processor hierarchy alongside general-purpose MCUs and DSPs. Key features include the 40 MHz / 40 MIPS 16-bit dsPIC core, 128KB self-programming Flash, extensive analog and digital peripherals typical of the dsPIC 33F General Purpose family, automotive AEC-Q100 qualification, and the thermally efficient 64-VFQFN exposed-pad package with 0.5 mm terminal pitch. Seamless migration options exist to PIC24 MCUs and dsPIC30F DSCs in similar packages. Architecturally, the device uses a modified Harvard, fixed-point CMOS core with multiple internal buses and a barrel shifter, supporting boundary scan (JTAG) for test. The A suffix denotes the enhanced revision of the dsPIC33FJ128GP306 die with improved errata coverage and peripheral refinements over the original part. Typical applications include automotive control modules, motor control and power conversion, digital power supplies, and industrial sensing and signal-conditioning systems where DSP math and robust MCU peripherals must coexist in a compact, thermally capable package. For design, decouple all VDD/VDDCORE pins with 0.1 uF ceramics close to the package and take full advantage of the exposed thermal pad for ground and heat conduction. The 9x9 mm QFN demands attention to via-in-pad design for rework access. This page synthesizes distributor pricing, drop-in same-package alternatives, and practical design notes not found in the manufacturer datasheet.

询价联系我们

DSPIC33FJ128GP306AT-I/MR

DSPIC33FJ128GP306AT-I/MR - 16-bit 40MIPS DSC 128KB Flash | Microchip

The Microchip Technology DSPIC33FJ128GP306AT-I/MR is a 16-bit digital signal controller (DSC) delivering 40 MIPS performance, 128 KB of Flash program memory, and 16 KB of RAM, housed in a 64-pin VQFN (9x9 mm) exposed-pad package with Tape & Reel packaging. A digital signal controller combines the computing model of a microcontroller with the numeric throughput of a DSP core. In the embedded-systems hierarchy, the dsPIC33F family sits between general-purpose PIC24 MCUs and dedicated DSPs, offering multiply-accumulate (MAC) instructions, a barrel shifter, and multiple internal buses while retaining conventional MCU peripherals such as timers, UARTs, and GPIO. This makes DSCs the natural choice for closed-loop control applications that also require fast numeric processing. Key features of this part include a 16-bit fixed-point core with DSP instruction extensions, 53 general-purpose I/O pins, an 18-channel 10-bit/12-bit analog-to-digital converter, and industrial temperature operation from -40C to +85C at a 3.0V to 3.6V supply. The 40 MIPs instruction rate supports real-time control loops at tens of kHz. Architecturally, the dsPIC33FJ128GP306 uses a modified Harvard bus structure with separate program and data paths, hardware loop support, and dual fetch of operands for single-cycle MAC operations. Seamless migration options exist toward PIC24 MCUs and dsPIC30F DSCs in similar packages, protecting long-term designs. Typical applications include motor control (BLDC, PMSM, FOC), digital power supplies and PFC stages, industrial automation sensors, and audio or general-purpose signal conditioning where the 10/12-bit ADC channels feed control algorithms. Design-wise, all VDD and VSS pins must be connected for reliable operation and programming; multiple PGECx/PGEDx ICSP pairs exist and must be used as matched pairs per the programming specification. This page synthesizes distributor pricing, drop-in alternatives, pinout guidance, and practical design notes not consolidated in the manufacturer datasheet.

询价联系我们

子分类

产品（39,000+)

DSPIC33FJ09GS302-E/TL - 40 MIPS SMPS DSC 9KB Flash | Microchip

DSPIC33FJ09GS302-I/MM - 16-bit 40 MIPS DSC | Microchip Technology

DSPIC33FJ09GS302-I/SO - 16-bit 40 MIPS DSC for SMPS | Microchip

DSPIC33FJ09GS302-I/SP - 16-bit DSC 40MIPS SMPS DSC | Microchip

DSPIC33FJ09GS302-I/SS - 16-bit DSC, 40 MIPS, 9KB Flash | Microchip

DSPIC33FJ09GS302T-E/MX - 16-bit DSC, 9KB Flash, QFN-28 | Microchip

DSPIC33FJ09GS302T-E/SO - 16-bit 40 MIPs DSC 9KB Flash | Microchip

DSPIC33FJ09GS302T-I/MM - 16-bit 40 MIPS DSC 9KB Flash | Microchip

DSPIC33FJ09GS302T-I/SO - 16-bit 40 MIPS DSC 9KB Flash | Microchip

DSPIC33FJ09GS302T-I/SS - 16-bit 40 MIPS DSC 9KB Flash | Microchip

DSPIC33FJ09GS302T-I/TL - 16-bit DSC 40 MIPS 9KB Flash | Microchip

DSPIC33FJ128GP202-E/MM - 16-bit DSC 128KB 40MIPS | Microchip

DSPIC33FJ128GP202-I/MM - 40MIPS 16-bit DSC, 128KB Flash | Microchip

DSPIC33FJ128GP202-I/SP - 16-bit DSC, 128KB Flash, 40 MIPS | Microchip

DSPIC33FJ128GP204-E/ML - 16-bit DSC 128KB 40MIPS | Microchip

DSPIC33FJ128GP204-E/PT - 16-bit DSC, 128KB Flash 40MIPS | Microchip

DSPIC33FJ128GP204-I/PT - 16-bit DSC 40MIPS 128KB Flash | Microchip

DSPIC33FJ128GP204T-I/PT - 16-bit DSC, 40 MIPS, 128KB Flash | Microchip

DSPIC33FJ128GP206AT-I/MR - 16-Bit 40MIPS DSC 128KB Flash | Microchip

DSPIC33FJ128GP206AT-I/PT - 16-bit 40MIPS DSC 128KB Flash | Microchip

DSPIC33FJ128GP206T-I/PT - 16-bit 40 MIPS DSC 128KB | Microchip

DSPIC33FJ128GP306-I/PT - 16-bit DSC 40MIPS 128KB Flash | Microchip

DSPIC33FJ128GP306A-E/MR - 16-bit DSC 40MIPS 128KB | Microchip

DSPIC33FJ128GP306AT-I/MR - 16-bit 40MIPS DSC 128KB Flash | Microchip