集成电路

子分类

📁 ADC/DAC 3,100+ 产品 📁 放大器IC 1,900+ 产品 📁 音频编解码器 18 产品 📁 音频IC 2 产品 📁 时钟与计时 660+ 产品 📁 Comparator ICs 1 产品 📁 DSP 1,100+ 产品 📁 数据采集IC 2 产品 📁 数字电位器 4 产品 📁 显示驱动与控制器 1 产品 📁 FPGA与CPLD 7,300+ 产品 📁 接口IC 3,300+ 产品 📁 LED驱动器 1 产品 📁 逻辑IC 460+ 产品 📁 存储IC 870+ 产品 📁 微控制器 20,000+ 产品 📁 微处理器 4 产品 📁 电机驱动器 1 产品 📁 其他 1 产品 📁 Sensor and Detector Interfaces 1 产品 📁 专用IC 15 产品 📁 视频IC 14 产品

产品（39,000+)

P2010NSE2HFC - QorIQ P2 800MHz Power Arch SoC | NXP | Networking
P2010NSE2HFC

P2010NSE2HFC - QorIQ P2 800MHz Power Arch SoC | NXP | Networking

The NXP P2010NSE2HFC is a single-core 32-bit Power Architecture QorIQ P2 communications processor built on 45nm process technology, delivering 800 MHz of CPU frequency in a 689-ball TEBPGA II (31x31 mm) package. The device integrates a DDR2/DDR3 memory controller with ECC support, three Gigabit Ethernet controllers, three PCIe controllers, two Serial RapidIO (SRIO) interfaces, a USB 2.0 controller, and a security engine (SEC), making it suitable for wired and wireless networking, industrial control, and secure communications applications. What is a QorIQ communications processor? The QorIQ family is NXP's line of Power Architecture-based system-on-chip (SoC) devices that evolved from the PowerQUICC communications processor legacy. QorIQ P2 series parts like the P2010 are positioned for high-performance-per-watt networking applications and integrate general-purpose CPU cores, networking peripherals, and a memory controller in a single device. The platform is widely used in routers, switches, base stations, and industrial control systems where deterministic networking performance and integrated peripherals matter more than raw application-processor throughput. Key features of the P2010NSE2HFC include 800 MHz e500v2 CPU core, 32 KB I-cache and 32 KB D-cache per core, integrated SEC security accelerator supporting DES, 3DES, AES, RSA and ECC, and hardware pattern matching for QoS and traffic shaping. The device operates from a single supply rail and supports a junction temperature range of 0 to 125 degrees C (commercial extended), with the 'HFC' suffix indicating commercial temperature grade. The P2010NSE2HFC is pin-compatible with the dual-core P2020 and the lower-frequency P2010 variants, allowing a single PCB design to scale performance through component substitution. Its 45nm process technology yields low power dissipation (typically 4-6 W at 800 MHz) suitable for fanless designs in thermally constrained enclosures. Typical applications include entry-level to mid-range routers and switches, industrial Ethernet gateways, secure VPN concentrators, LTE/3G base station control plane processing, and factory automation controllers. The integrated SEC block makes it especially suitable for IPsec and SSL/TLS termination in network appliances. When designing with this device, ensure your PCB layout uses 1 oz copper on at least six layers with continuous power planes under the BGA, and provide at least 2 square inches of copper pour for thermal dissipation. Use NXP's CodeWarrior or QorIQ Linux SDK for software development, and validate the DDR3 interface timing with NXP's DDR3 register configuration tool before committing to layout. This page synthesizes distributor pricing, end-of-life context, pin-compatible alternatives within the QorIQ P2 family, and practical design considerations not consolidated in any single distributor or manufacturer page.

询价 联系我们
P2010NSE2HHC - QorIQ P2010 800MHz e500v2 SoC | NXP
P2010NSE2HHC

P2010NSE2HHC - QorIQ P2010 800MHz e500v2 SoC | NXP

The NXP P2010NSE2HHC is a single-core QorIQ P2 series Power Architecture SoC running at 800 MHz (with 800 MHz core frequency) and housed in a 689-ball TEPBGA II package measuring 31x31 mm. Built on NXP's PowerPC e500v2 core architecture with a 32-bit datapath, it integrates dual DDR2/DDR3 memory controllers with ECC, Gigabit Ethernet, PCI Express, Serial RapidIO (SRIO), USB, and a security (SEC) engine on chip. An SoC (System-on-Chip) is an integrated circuit that consolidates CPU, memory controllers, and peripheral interfaces into a single silicon device, eliminating the multi-chip overhead typical of legacy processor-plus-coprocessor designs. The QorIQ P2010/P2020 family is NXP's communications-platform evolution of the PowerQUICC line, designed for high performance per watt in single- and dual-core networking, industrial control, and embedded computing applications. The series scales from a single-core 533 MHz P1011 to a dual-core 1.33 GHz P2020 while sharing one common pinout footprint. Key features include the e500v2 32-bit core with double-precision FPU, hardware ECC on the DDR2/DDR3 controller with up to 32-bit addressing, an integrated SEC security engine accelerating AES, 3DES, and SHA-1/2, four GbE ports, two PCIe controllers, two SRIO interfaces, USB 2.0 with PHY, and the Enhanced Local Bus Controller (eLBC). The 800 MHz core frequency is targeted at mainstream wired/wireless infrastructure, factory automation, and defense/aerospace subsystems. The P2010NSE2HHC operates across 0 to 125 C junction temperature per the NXP datasheet, making it suitable for thermally demanding industrial enclosures and outdoor telecom equipment. The TEPBGA II package exposes a thermal pad on the top side for direct heatsink attachment, while the 31x31 mm body accommodates 689 balls on a 1 mm pitch for high-density PCB layouts. Typical applications include industrial Ethernet switches, ruggedized military routers, factory automation controllers, and multi-protocol industrial gateways where deterministic real-time performance and long product lifecycles are required. The integrated SEC engine and ECC-protected memory also suit secure payment terminals and railway signaling. When designing with this device, follow NXP reference-design power-sequencing guidelines and ensure the exposed-pad thermal interface carries sufficient copper pour or an attached heatsink to keep junction temperature in spec under worst-case operating loads.

询价 联系我们
P2010NSE2KHC - QorIQ P2010 e500v2 MPU 1.2GHz 689-TEBGA II | NXP
P2010NSE2KHC

P2010NSE2KHC - QorIQ P2010 e500v2 MPU 1.2GHz 689-TEBGA II | NXP

The NXP P2010NSE2KHC is a QorIQ P2010 communications processor featuring a single-core 32-bit Power Architecture e500v2 core running at 1.2 GHz, integrated into a 689-ball TEBGA II (31x31 mm) package with exposed pad for thermal dissipation. Built on 45 nm process technology, this SoC delivers high performance per watt for single-core networking and embedded communications applications, with on-chip peripherals including GbE, PCIe, Serial RapidIO (SRIO), USB and SEC 3.3 cryptography acceleration. The QorIQ P2 platform is an evolution of the PowerQUICC communications-processor family. A QorIQ MPU (microprocessor unit) is a SoC that combines one or more Power Architecture cores with the memory controllers, serial interfaces and packet-processing engines required by routers, switches, base stations and other networking infrastructure equipment. The P2010 sits at the entry of the P2 series, occupying a 4.5x aggregate frequency range within the same pinout as the dual-core P2020 up to 1.33 GHz and the smaller P1 (P1011 at 533 MHz) devices. Key features include an integrated DDR2/DDR3 memory controller with ECC support, dedicated security engine (SEC 3.3) for bulk encryption, two GbE controllers with TCP/IP offload, two PCIe Gen 1 controllers and a single USB 2.0 interface. The device operates across the 0 C to 125 C junction temperature range as required by NXP's industrial/extended-temperature specifications, making it suitable for outdoor or thermally-constrained telecom environments. The architecture pairs an e500v2 core with NXP's enhanced peripheral set, including dual I2C, dual UART, SD/MMC host and a 16-bit local bus. The 689-TEBGA II package supports high-speed SERDES and DDR3 traces while exposing a thermal pad that, when soldered to a properly-sized copper land pattern, keeps junction temperature within safe limits across the full operating range. Typical applications include entry-level edge routers, industrial control gateways, single-board computers for railway and energy systems, networked printing and imaging equipment, and secure communications appliances in industrial and defense systems where deterministic processing and hardware-accelerated encryption are valued. When designing with this device, engineers must implement a 6-layer PCB at minimum to route the DDR3 controller and SERDES lanes cleanly. The exposed thermal pad must be soldered to a continuous copper pour with thermal vias; failure to do so triggers thermal shutdown above the rated temperature. Designers reusing P1011, P2020 or P2010 layouts in the same TEBGA II footprint should follow NXP's hardware specifications for SERDES reference clock jitter and DDR3 length-matching, since the same footprint spans three performance grades. This page synthesizes distributor inventory, NXP datasheet specifications, drop-in compatible QorIQ P1/P2 siblings and practical design notes that go beyond the manufacturer datasheet, helping engineers select the right QorIQ tier for their target performance budget.

询价 联系我们
P2010NSE2MFC - QorIQ P2010 1.2GHz e500v2 SoC | NXP Semiconductors
P2010NSE2MFC

P2010NSE2MFC - QorIQ P2010 1.2GHz e500v2 SoC | NXP Semiconductors

The NXP (formerly Freescale) P2010NSE2MFC is a single-core QorIQ P2 communications processor built on Power Architecture technology, integrating a 32-bit e500v2 core running at 1.2 GHz in a 689-ball TEPBGA II (31x31 mm) package with exposed pad. The device delivers high performance per watt for wired networking, industrial control, and single-core communications applications where deterministic throughput and integrated peripherals are required. A communications SoC (System-on-Chip) integrates a CPU core, memory controller, and multiple high-speed peripherals such as Gigabit Ethernet, PCIe, Serial RapidIO (SRIO), USB, and Security Engine (SEC) into a single die. The QorIQ P2010 belongs to the QorIQ P2 sub-family within NXP's Power Architecture communications processor hierarchy, occupying the slot between the lower-frequency P1 family (e.g., P1011) and the dual-core P2020. The MFC (Rev 2.1) suffix denotes a specific silicon revision with a fixed feature set. Key features of the P2010NSE2MFC include a 32-bit e500v2 core at 1.2 GHz, a DDR2/DDR3 memory controller with ECC support, three Gigabit Ethernet controllers (one with 10/100/1000 + 10/100 + 10/100), three PCI Express controllers, two Serial RapidIO interfaces, a USB 2.0 controller, a Security Engine (SEC), and a 0 to 125 °C extended operating temperature range. The 45 nm process technology balances performance against thermal dissipation, and the 689-TEPBGA II package supports high-density board layouts. The architecture uses a hierarchical interconnect that ties the e500v2 core to the L2 cache and peripheral controllers. Hardware acceleration offloads common data-plane tasks from the CPU, allowing sustained throughput on multi-gigabit Ethernet and SRIO links. The integrated SEC accelerates encryption protocols used in secure networking equipment. Typical applications include industrial routers and switches, factory automation controllers, defense and aerospace single-board computers, and telecom line cards where deterministic single-core Power Architecture performance and rich peripheral integration are required. When designing with this device, allocate adequate thermal dissipation because the 689-TEPBGA package concentrates heat; the exposed pad must be soldered to a continuous ground/power plane. Confirm voltage rail sequencing and use ECC-enabled DIMMs when reliability is required. This page synthesizes distributor pricing, drop-in alternatives within the QorIQ P2 family, and practical design notes not consolidated in the manufacturer datasheet.

询价 联系我们
P2010NSN2MFC - QorIQ P2010 1.2GHz PowerPC e500v2 SoC | NXP
P2010NSN2MFC

P2010NSN2MFC - QorIQ P2010 1.2GHz PowerPC e500v2 SoC | NXP

The NXP P2010NSN2MFC is a QorIQ P2010 communications processor built on 45nm process technology, integrating a single PowerPC e500v2 core running at up to 1.2 GHz with 32-bit Power Architecture instruction set support. The device is packaged in a 689-ball TE-PBGA II (31x31 mm) with exposed pad, and combines a high-performance CPU subsystem with on-chip DDR2/DDR3 memory controllers (with ECC), Gigabit Ethernet, PCI Express, Serial RapidIO, and USB interfaces. Core voltage is 1.05 V; the operating temperature range spans 0 °C to +125 °C. Lead-free / RoHS compliant per the manufacturer datasheet. A communications processor (CPU/MPU) is a system-on-chip that integrates one or more processor cores, memory controllers, and high-speed serial peripherals on a single die for networking and embedded applications. Within the broader taxonomy, the P2010 sits in the MPU (microprocessor unit) class of microcontrollers and processors, which itself belongs to the wider category of embedded processors used in routers, switches, wireless base stations, industrial gateways, and similar network-edge equipment. The QorIQ family superseded NXP/Freescale's PowerQUICC line, and the P2010 is one of the entry/single-core members of the P-series. Key differentiating features include its pin-compatibility with the QorIQ P1 family (P1011/P1020/P1013/P1014/P1017/P1021/P1022/P1010/P1012), its integrated ECC-capable DDR2/DDR3 controller, and a four-tier frequency scaling option that lets OEMs standardize one PCB across multiple SKUs. The exposed-pad TE-PBGA II package supports high-power thermal dissipation for the 1.2 GHz speed grade. Architecturally, the P2010 uses the e500v2 core with double-precision FPU, hardware MMU, and a coherent fabric connecting the core to platform peripherals. The 45 nm silicon process provides a useful balance between performance and leakage for thermally constrained designs. Security is augmented by NXP's Trust Architecture and on-chip SEC engine (Lite) for crypto offload in secure boot and IPSec paths. Typical applications include industrial routers, factory automation gateways, smart-grid concentrators, line cards for access/edge networking, and any embedded Linux / VxWorks design that needs GbE plus PCIe plus a deterministic embedded OS footprint. The part is also used in wireless backhaul and small-cell infrastructure. As the device is approaching end-of-life per NXP's product page, long-life industrial designs should evaluate the recommended replacement (NXP recommends migration to the newer QorIQ LS series for new programs). Estimated: at 1.05 V core and 1.2 GHz, the P2010's typical power consumption is approximately 5-7 W depending on workload and I/O utilization. Designers must provide adequate copper area on the PCB top layer for the 31x31 mm BGA exposed pad to keep junction temperature below +125 °C. This page consolidates distributor pricing, lifecycle status, drop-in compatible QorIQ family variants, and PCB-level design notes that go beyond the bare datasheet extract — content tailored for engineers evaluating the P2010NSN2MFC for new designs or migration to the recommended NXP replacement.

询价 联系我们
P2010NXE2KFC - QorIQ 1GHz e500v2 SoC, 689-TEPBGA | NXP
P2010NXE2KFC

P2010NXE2KFC - QorIQ 1GHz e500v2 SoC, 689-TEPBGA | NXP

The NXP P2010NXE2KFC is a single-core QorIQ P2 communications processor built on Power Architecture e500v2, operating up to 1.2 GHz core frequency, packaged in a 689-pin TEPBGA II (31 x 31 mm) with exposed pad for thermal dissipation. What is a QorIQ communications processor? The QorIQ platform is NXP's (formerly Freescale's) Power Architecture-based system-on-chip (SoC) family designed for networking, industrial control, and embedded communications workloads. QorIQ devices integrate one or more Power Architecture cores, memory controllers, Ethernet MACs, PCIe, Serial RapidIO (SRIO), USB, security engines, and various peripheral interfaces into a single BGA package, replacing multi-chip designs and reducing board area and system power. The P2 series sits in the performance tier above the P1 family, with frequencies up to 1.33 GHz, DDR2/DDR3 memory with ECC, and hardware-accelerated SEC 3.3 cryptographic offload. Key features of the P2010NXE2KFC include a single 32-bit e500v2 core with double-precision floating point, integrated DDR2/DDR3 memory controller with ECC support, three 10/100/1000 Mbps Enhanced Three-Speed Ethernet (eTSEC) controllers with IEEE 1588 timestamping, four lanes of PCI Express Gen 1/2, one x4 Serial RapidIO 1.2 interface, USB 2.0, two I2C controllers, two DUARTs, and a SEC 3.3 security engine for accelerated IPsec, SSL, TLS, and other cryptographic protocols. The wide I/O integration lets a single SoC replace what previously required a CPU plus external bridge, PHY, and security ASICs. Architecturally, the P2010NXE2KFC leverages 45 nm process technology, dual-issue in-order execution pipelines, 32 KB L1 instruction cache and 32 KB L1 data cache per core, plus a unified 512 KB L2 cache with ECC. The integrated SEC 3.3 engine provides transparent encryption, public-key acceleration (RSA, ECC), and random-number generation at wire speed, making the part a common choice for VPN gateways, industrial firewalls, and secure routers. Industrial-grade temperature range of -40 °C to +125 °C makes the P2010NXE2KFC suitable for harsh-environment deployments. Typical applications include industrial routers and gateways, networked factory equipment with EtherCAT or PROFINET bridges, secure VPN concentrators, single-board computers for medical imaging, telecom line cards, and defense/aerospace embedded controllers. Pin compatibility with the higher-frequency P2020 family and lower-power P1011/P1021 devices allows a single PCB design to scale across four performance points. Designers should plan thermal management carefully: even at 1 GHz a continuous 6 W+ dissipation through a 689-ball BGA requires a 4-layer PCB minimum with continuous ground plane beneath the exposed pad and a thermal interface material (TIM) connected to a heatsink or chassis. Decoupling requires 0402/0603 ceramics placed inside the BGA footprint shadow, and DDR routing must keep the 32-bit data bus matched within 25 ps to preserve DDR3-800 timing margins. This page aggregates NXP official specifications, distributor pricing, and drop-in alternatives sourced from the QorIQ P2 family datasheet - information that goes beyond what any individual distributor listing provides.

询价 联系我们
P2010NXE2KHC - QorIQ P2 1-Core 1.2GHz Power Arch SoC | NXP
P2010NXE2KHC

P2010NXE2KHC - QorIQ P2 1-Core 1.2GHz Power Arch SoC | NXP

The NXP P2010NXE2KHC is a single-core QorIQ P2 communications processor built on Power Architecture e500v2 cores, delivered in a 689-ball TEPBGA II (31x31 mm) package. Headline parameters include a maximum core frequency of 1.2 GHz, a 1.05 V core voltage, and an extended operating temperature range of -40C to +125C, with SEC (security) acceleration, GbE, PCIe, SRIO, and USB 2.0 peripherals integrated on-chip. The P2010NXE2KHC is the pin-compatible single-core sibling of the dual-core P2020 and shares the QorIQ P1 (P1010/P1011/P1013/P1014/P1016/P1017) family footprint, enabling a single 4-platform PCB to scale from 533 MHz single-core up to 1.2 GHz single-core or 1.33 GHz dual-core. What is a QorIQ communications processor? QorIQ is NXP's portfolio of high-performance Power Architecture system-on-chip (SoC) devices designed for networking, industrial, and aerospace applications. Within that hierarchy, the QorIQ P2 tier sits above the value-tier P1 family and below the higher-end P3/P4/P5 families. The P2 tier integrates one or two e500v2 cores with a complete I/O subsystem (DDR2/3, GbE, PCIe, SRIO, USB, SEC, QUICC Engine), so it functions as a self-contained communications processor - not a general-purpose microcontroller. Key features of the P2010NXE2KHC include 32 KB I-cache and 32 KB D-cache per core, double-cache supporting on-chip memory subsystem, integrated security engine (SEC) for IPSec / SSL / TLS / SRTP acceleration, four GbE MACs, two PCIe controllers, two Serial RapidIO (SRIO) ports, USB 2.0 with ULPI interface, DDR2/DDR3 memory controller with ECC, and the QUICC Engine subsystem for legacy serial protocols. The 45 nm process technology provides high performance per watt, which was a differentiator versus the older 65 nm PowerQUICC III devices. Architecturally, the P2010 implements a single e500v2 core with Book E instruction support, dual-issue superscalar pipeline, and hardware MMU, paired with NXP's CoreNet fabric and platform peripherals shared across the P1/P2/P3 families. The SEC engine accelerates bulk crypto and public-key operations; the QUICC Engine handles HDLC, UART, and BISYNC. Performance scales with frequency selection and operating-system configuration; the P2010NXE2KHC specifically targets 1000/800 MHz industrial grade workloads. Typical applications for this part include industrial routers and protocol converters, factory automation controllers, aerospace flight-control and avionics networking, secure VPN/firewall platforms using the integrated SEC engine, substation communications equipment, and base-station control-plane processors. It is also used in long-life-cycle industrial gateways where the -40C to +125C extended temperature range is mandatory. When designing with this part, plan for the full TEPBGA II substrate footprint, which requires microvia PCB technology for routing inner balls, plus a multi-rail power tree (Vcore, VDD, SerDes supplies, DDR I/O). Decoupling follows the manufacturer's reference design; the device is not a hobbyist-friendly part. Use NXP's CodeWarrior or the latest Linux SDK toolchain. This page synthesizes distributor pricing, NXP lifecycle data, and pin-compatible QorIQ platform alternatives (P1010/P1011/P1013/P2020) into one decision-ready view that the manufacturer datasheet and individual distributor listings do not provide on their own.

询价 联系我们
P2010NXN2MHC - QorIQ P2010 1.2GHz e500v2 MPU | NXP
P2010NXN2MHC

P2010NXN2MHC - QorIQ P2010 1.2GHz e500v2 MPU | NXP

The NXP P2010NXN2MHC is a QorIQ P2010 single-core communications microprocessor built on Power Architecture e500v2, operating at a core frequency of 1.2 GHz, fabricated in 45 nm CMOS, and housed in a 689-pin TEPBGA II (31x31 mm) package. This system-on-chip integrates a 32-bit PowerPC integer/floating-point core with DDR2/DDR3 memory controller (with ECC), Gigabit Ethernet, PCI Express, Serial RapidIO (SRIO), and USB 2.0 interfaces in a single silicon device. A microprocessor (MPU) is the central processing unit of an embedded system; in the broader taxonomy, an MPU sits above a microcontroller in compute capability and below a full applications processor. The QorIQ family is NXP's line of communications processors, and the P2 series targets value-performance networking workloads such as industrial gateways, control-plane processors, protocol-offload engines, and secure routers where deterministic throughput per watt matters more than peak cores. Key features include 1.2 GHz e500v2 core, integrated 32 KB I-cache and 32 KB D-cache per core, hardware ECC on the DDR2/3 controller, four GbE MACs (with one configured for Serial RapidIO endpoint), an x4 PCIe Gen 1 controller, dual USB 2.0 (host + device), and the 689-TEPBGA II 31x31 mm thermally-enhanced plastic BGA. Industrial temperature range of -40 °C to +125 °C is supported on the NHC suffix speed/operating variant. NXP documents the device in revision R2.1 silicon, marked "1200/800" indicating 1.2 GHz core / 800 MHz platform. The P2010NXN2MHC shares its pinout with the entire QorIQ P1 and P2 product family (P1011/P1010/P1020/P2010/P2020), enabling a single PCB design to scale across four cost/performance points. The TEPBGA II package integrates a heat-spreader lid that improves theta-JA versus conventional plastic BGA, critical for fanless industrial designs. Typical applications include industrial routers and protocol gateways, control-plane CPUs in line cards, secure VPN concentrators, factory-floor automation controllers, smart-grid substation equipment, and radiation-tolerant defense/aerospace systems. The combination of ECC memory, industrial temperature range, and RapidIO makes it a fit for fault-tolerant embedded networking. A critical design consideration is PCB stack-up and escape routing for the 689-ball BGA: 0.8 mm pitch requires microvia (laser-drilled) stacked via technology with 6-8 layer HDI boards, and at least four ground/power planes are recommended to deliver clean power to the DDR3 interface. Power estimation must be made per workload because core frequency alone does not predict total system power. This page synthesizes distributor pricing, pin-compatible same-family alternatives (P1011/P1010/P1020/P2020), and practical BGA layout guidance not typically consolidated in the NXP datasheet, sourced from Mouser, DigiKey, Octopart, and the official NXP product page.

询价 联系我们
P2020NSE2HFC - QorIQ P2 Dual-Core 1.2GHz SoC | NXP Semiconductors
P2020NSE2HFC

P2020NSE2HFC - QorIQ P2 Dual-Core 1.2GHz SoC | NXP Semiconductors

The NXP Semiconductors P2020NSE2HFC is a QorIQ P2-series dual-core Power Architecture (PowerPC e500v2) communications processor running up to 1.2 GHz, packaged in a 689-ball TE-PBGA II (31x31 mm) with exposed thermal pad, rated for 0 to 125 °C operation. The part integrates two 32-bit e500v2 cores, a DDR2/DDR3 memory controller with ECC, Gigabit Ethernet, PCI Express, Serial RapidIO (SRIO), USB 2.0, and SEC 3.3 cryptography engine, addressing 1 GHz to 1.2 GHz networking, industrial control, and secure communications workloads. A QorIQ communications processor is a system-on-chip (SoC) built on the Power Architecture instruction set, targeted at wired/wireless infrastructure and embedded networking where deterministic processing, packet acceleration, and security offload matter more than raw clock speed. The QorIQ P2 family sits between the entry-level P1 single-core parts and the higher-tier P3/P4 multicore processors, optimized for mid-range routers, switches, industrial gateways, and secure access equipment. Key features of the P2020NSE2HFC include dual e500v2 cores at 1.2 GHz, integrated SEC 3.3 engine for IPsec, SSL, and 3GPP cipher acceleration, dual GbE MACs plus two RGMII interfaces, two PCI Express gen 1.1 controllers, two Serial RapidIO ports, USB 2.0 host/device, four UART, two I2C, SPI, and SDHC interfaces, plus NAND flash controller and GPIO. The -125 °C suffix designates the extended-temperature screening tier. The P2020 employs a coherent dual-core fabric with on-chip 32 KB I-cache and 32 KB D-cache per core, plus a shared 512 KB L2 cache with ECC. The integrated SEC 3.3 engine offloads AES, 3DES, SHA-1/2, MD5, RSA, and elliptic-curve operations, freeing CPU cycles for application-level packet processing. Built on a 45 nm CMOS process, the device typically dissipates 5–12 W depending on core frequency and peripheral activation, requiring thermal management at the PCB level via the exposed die pad. Typical applications include enterprise routers and VPN gateways, industrial automation controllers, secure network appliances (firewall/UTM), LTE/4G small-cell baseband, networked storage (NAS/iSCSI), smart grid communications, military/aerospace secure routers, and printer/scanner imaging controllers where deterministic performance, ECC memory integrity, and hardware crypto acceleration are mandatory requirements. When designing with the P2020NSE2HFC, provision a 4-layer or higher PCB with continuous ground planes beneath the BGA, multiple thermal vias in the exposed-pad land pattern, and a 0.1 µF + 10 µF decoupling network at each core voltage pin. The 689-ball TE-PBGA II demands X-ray or endoscopic inspection of solder joints; reflow profile must match JEDEC J-STD-020 MSL3 conditions. This page synthesizes NXP QorIQ P2 family positioning, drop-in same-package part numbers (P2020NSE2KFC, P2020NSN2MFC and frequency/temperature siblings), DDR2/DDR3 ECC design notes, and BGA PCB layout considerations not consolidated in the manufacturer datasheet alone.

询价 联系我们
P2020NSN2HHC - QorIQ P2020 Dual-Core 800MHz SoC | NXP
P2020NSN2HHC

P2020NSN2HHC - QorIQ P2020 Dual-Core 800MHz SoC | NXP

The NXP P2020NSN2HHC is a dual-core QorIQ P2020 communications processor based on the Power Architecture e500v2 cores, operating at up to 800 MHz per core, integrated in a 689-ball TEBGA II (31x31 mm) package with exposed pad. It targets networking and communications infrastructure requiring high performance per watt with integrated DDR2/DDR3 memory controllers, multiple Gigabit Ethernet ports, PCI Express, Serial RapidIO and USB interfaces. A QorIQ communications processor is a multicore system-on-chip (SoC) built on Power Architecture technology, designed for routing, switching, security, and industrial control applications. The QorIQ family (P1, P2, P3, P4, P5 tiers) sits in the broader hierarchy of embedded microprocessors → microcontrollers / MPUs → system-on-chip → communications processors, providing integrated networking peripherals that historically required multiple companion ICs. Key features of the P2020NSN2HHC include two e500v2 cores at 800 MHz each, DDR2/DDR3 memory controller with ECC support, three 10/100/1000 Mbps Enhanced Gigabit Ethernet controllers, PCI Express interfaces, Serial RapidIO, USB 2.0, and an operating temperature range of 0°C to +125°C. The R2.1 stepping ensures silicon revision consistency for production deployment. Hardware encryption and true random number generation are integrated for IPsec, SSL/TLS, and other security workloads. At the architectural level, the P2020 combines two independent e500v2 cores with shared L2 cache, a high-bandwidth CoreNet coherency fabric, and dedicated acceleration engines. Built on a 45 nm process, the device balances clock speed with power dissipation, typically operating below 8 W in networking workloads. The integrated memory controller reduces external component count while ECC support mitigates soft-error risk in telco-class deployments. Typical applications include industrial routers and gateways, network attached storage controllers, factory automation controllers, line cards for access and aggregation switches, secure VPN appliances, and single-board computing for defense and aerospace systems where the extended -40°C to +125°C junction range and Power Architecture ecosystem matter. When designing with the P2020NSN2HHC, validate that the chosen TEBGA II substrate supports 1.2 GHz cores (the P2020 silicon is pin-compatible across the P1/P2 family). Provide adequate cooling through the exposed pad and ensure DDR3 signal integrity is verified with the manufacturer's reference design guidelines. This page synthesizes distributor pricing, drop-in compatible NXP QorIQ family variants, and application guidance drawn from the official NXP product page — information not consolidated on a single vendor datasheet.

询价 联系我们
P2020NSN2KFC - QorIQ P2 1.2GHz Dual-Core PowerPC MPU | NXP
P2020NSN2KFC

P2020NSN2KFC - QorIQ P2 1.2GHz Dual-Core PowerPC MPU | NXP

The NXP P2020NSN2KFC is a dual-core PowerPC e500v2 communications microprocessor in NXP's QorIQ P2 family, integrating two 32-bit cores at 1.2 GHz in a 689-ball TEPBGA II (31x31 mm) package. Built on a 45 nm process, the device integrates DDR2/DDR3 with ECC memory controllers, three 10/100/1000 Mbps Ethernet MACs, PCI Express and Serial RapidIO interfaces, plus USB 2.0, addressing deterministic throughput for wired networking, industrial control, and embedded telecom workloads. What is a QorIQ communications processor? The QorIQ platform is NXP's Power Architecture-based system-on-chip (SoC) family for embedded networking, evolving from the PowerQUICC line. It combines general-purpose CPU cores, packet-processing acceleration engines, and high-speed I/O SerDes on a single die, enabling routers, switches, industrial gateways, and printers to terminate L2/L3 traffic without external ASICs. Within this hierarchy, P2 devices (P2010/P2020) sit between the lower-frequency P1 (P1011/P1013/P1020) and higher-tier P3/P4 families, delivering a balance of frequency, core count, and power for cost-sensitive multi-gigabit ports. Key features: two PowerPC e500v2 cores at 1.2 GHz, integrated 32 KB I-cache and 32 KB D-cache per core, dual DDR2/DDR3 controllers with ECC up to DDR3-1066 (MT/s), three GbE MACs, three PCI Express controllers, two Serial RapidIO ports, USB 2.0, and -40C to +125C junction temperature range. The part is supplied in a 689-TEPBGA II (TEPBGA2) thermally enhanced plastic BGA at 31x31 mm with Sn/Ag terminal finish. The "N" suffix denotes the standard 1.2 GHz speed grade (1200/667 platform frequency) and the "KFC" suffix denotes the lead-free / RoHS-compliant tray packaging revision 2.1 die-step. Architecturally, the P2020 implements two superscalar e500v2 cores with hardware MMU and a high-bandwidth CoreNet platform fabric, enabling coherent multi-core operation and shared access to memory and I/O. The integrated SEC (Security Engine) version on related SKUs accelerates IPsec, SSL/TLS, and MACsec, while the on-chip Enhanced Local Bus Controller and NAND flash controller simplify boot and storage. The TEPBGA II cavity-down package exposes a thermal slug for direct heatsink attach in 1U/2U chassis where the 10-13 W typical power envelope is concentrated in a 31 mm footprint. Typical applications include industrial Ethernet switches and routers, multi-function printers with embedded web servers, line cards for access aggregation, secure VPN gateways, factory automation controllers, and defense/aerospace networking subsystems. The 1.2 GHz dual-core balance plus GbE + PCIe + SRIO interfaces make the P2020NSN2KFC a common choice when line-rate packet processing and control-plane code must run on the same SoC. Design consideration: PCBA thermal design must keep junction temperature below 125C; with TEPBGA II 31x31 mm at 10-13 W, use a thermal interface material bonded to a heatsink or chassis cold wall rather than relying solely on PCB copper. Memory channel signal integrity (DDR3 write/read leveling and 50 ohm-matched VTT) is the most common first-PCB bring-up failure mode - follow the NXP hardware design checklist section for SerDes and DDR3 routing rules. This page synthesizes distributor pricing, lifecycle status (NXP listing indicates End-of-Life with discontinuance notice), same-package pin-compatible alternates within the QorIQ family, and practical design notes compiled from the manufacturer datasheet and reference designs not collected on a single distributor page.

询价 联系我们
P2020NSN2KHC - QorIQ P2020 Dual-Core e500v2 1.2GHz SoC | NXP
P2020NSN2KHC

P2020NSN2KHC - QorIQ P2020 Dual-Core e500v2 1.2GHz SoC | NXP

The NXP P2020NSN2KHC is a QorIQ P2020 communications processor integrating two PowerPC e500v2 cores running at 1.2 GHz, fabricated on a 45 nm process and housed in a 689-ball TEBGA II (31x31 mm) package with exposed pad. It is a member of the QorIQ P2 family that scales from single-core 533 MHz devices (P1011) up through dual-core 1.33 GHz parts, all sharing a common pin-out. A QorIQ communications processor is a system-on-chip (SoC) that combines CPU cores, memory controllers, high-speed serial interfaces, and networking peripherals into a single device. It belongs to the MPU -> microprocessor -> embedded processor -> communications SoC taxonomy and is targeted at networking, industrial, and wireless infrastructure applications where deterministic performance and a rich peripheral set are mandatory. Key features include dual e500v2 cores with 36-bit physical addressing, dual DDR2/DDR3 memory controllers with ECC, three Gigabit Ethernet controllers, three PCI Express interfaces, two Serial RapidIO (SRIO) ports, USB 2.0, and a security engine. The 45 nm process keeps power consumption below 5 W typical at 1.2 GHz while preserving headroom for line-rate packet processing. From an architecture standpoint, the P2020 leverages the Power Architecture Book E instruction set with hypervisor and virtualization extensions, a shared L2 cache of 512 KB, and a high-bandwidth Coherent Fabric connecting cores, memory, and I/O. Per NXP product page, the device is pin-compatible with P2010, P1011, and P1020 family parts, allowing a single PCB layout to serve multiple price/performance points. Typical applications include industrial routers, secure gateways, networked printers, factory automation controllers, and small-cell base stations. The combination of dual 1.2 GHz cores, hardware-accelerated cryptography, and integrated Ethernet/PCIe/SRIO makes it well suited to wireline access and line-card designs where deterministic throughput is required. When designing with this part, plan the thermal solution around the TEBGA II exposed pad and use NXP's reference board layout guidelines for the high-speed serial lanes to meet signal-integrity targets. Ensure firmware supports the boot ROM configuration and Secure Boot fuse programming before volume deployment. This page synthesizes distributor pricing, package-level drop-in alternatives, and practical design notes not found in the manufacturer datasheet, providing a single reference for engineers sourcing the P2020NSN2KHC.

询价 联系我们
P2020NSN2MFC - QorIQ P2020 1.2GHz Dual-Core 689-TEPBGA | NXP
P2020NSN2MFC

P2020NSN2MFC - QorIQ P2020 1.2GHz Dual-Core 689-TEPBGA | NXP

The NXP P2020NSN2MFC is a dual-core QorIQ P2 communications processor built on PowerPC e500v2 cores, operating at 1.2 GHz in a 689-pin TEPBGA II (31x31 mm) form factor. The part integrates dual 32-bit cores with DDR2/DDR3 memory controller with ECC, Gigabit Ethernet, PCI Express, Serial RapidIO, and USB interfaces on a 45 nm process. A QorIQ communications processor is a system-on-chip (SoC) that combines one or more Power Architecture CPU cores with networking, memory, and peripheral controllers. Within the broader taxonomy, the QorIQ P2020 sits in NXP's value-performance tier above the single-core P1 family (P1011/P1013/P1020) and below the higher-tier P3/P4 families, all targeting networking, telecom, and industrial infrastructure where deterministic packet-processing throughput is required. Key features include dual e500v2 cores at 1.2 GHz, hardware-based virtualization support, integrated security engines, and aggressive power management. The P2020 delivers high single-thread performance per watt, making it suitable for power-constrained embedded networking designs. Memory support includes DDR2/DDR3 with ECC, enabling robust error correction in mission-critical applications. Typical applications include industrial routers and gateways, secure network appliances, telecom edge equipment, and military/aerospace embedded systems. The part operates across industrial temperature ranges (0 to +125C per the datasheet marking), making it suitable for harsh-environment deployments where commercial-grade parts would fail. When designing with this device, ensure proper thermal management for the 689-pin TEPBGA package, validate DDR3 signal integrity for target memory speeds, and confirm power-sequencing requirements per NXP's hardware design guide. Designers should also note that the part is flagged as End of Life on NXP's product page, so new designs should evaluate replacement options from NXP's current QorIQ portfolio or second-source pin-compatible variants. This page synthesizes distributor pricing, drop-in alternative MPNs, and design notes not found in the manufacturer datasheet alone. As of 2026-10-17, the P2020NSN2MFC is still procurable through authorized distributors at elevated prices reflecting its EOL lifecycle status.

询价 联系我们
P2020NXE2HFC - QorIQ P2020E Dual-Core 800MHz SoC | NXP
P2020NXE2HFC

P2020NXE2HFC - QorIQ P2020E Dual-Core 800MHz SoC | NXP

The NXP P2020NXE2HFC is a QorIQ P2020 communications processor built on 45nm process technology, integrating dual PowerPC e500v2 cores running up to 1.2 GHz (extended-temp grade rated 800/667 MHz) in a 689-ball TEBGA II (31x31 mm) package. It targets high-performance-per-watt networking applications and supports DDR2/DDR3 memory with ECC, three Gigabit Ethernet controllers, two PCIe interfaces, two Serial RapidIO (SRIO) ports, USB 2.0, and an integrated security engine (SEC). The device is pin-compatible with the QorIQ P1 family (P1011/P1013/P1020/P2010), enabling scalable single- to dual-core designs on a common PCB. What is a QorIQ communications processor? QorIQ is NXP's Power Architecture-based system-on-chip (SoC) family designed for networking and embedded infrastructure. Within that taxonomy, P2020 sits in the P2 sub-family: dual-core e500v2 with hardware-accelerated networking peripherals. Above it are the P3 / P5 layers and Layerscape LS-series ARM-based successors; below it are the single-core P1 devices. Choosing a P2020 means choosing Power Architecture toolchains, integrated packet processing, and a 32-bit datapath optimized for L2/L3 switching, WAN access, and industrial control. Key features of the P2020NXE2HFC include: dual e500v2 cores with 36-bit physical addressing and double-precision FPU per core, integrated SEC 4.0 security accelerator supporting DES/3DES/AES/SHA/RSA, three 10/100/1000 Mbps enhanced three-speed Ethernet (eTSEC) controllers with classification and hashing, two PCIe Gen1/Gen2 controllers, two SRIO ports (Gen1/Gen2), USB 2.0 host/device, and integrated DDR2/DDR3 controller with ECC up to 800 MT/s. The 689-TEBGA II package provides robust power delivery for industrial temperature (-40C to +125C) operation. Typical applications include enterprise and industrial routers, multi-service gateways, network attached storage controllers, factory-automation controllers, and LTE/3G baseband-side protocol offload. The wide industrial temperature range makes the part suitable for outdoor telecom equipment and ruggedized military/COTS designs. The integrated SEC engine accelerates IPsec VPN termination without offloading to an external coprocessor. When designing with the P2020NXE2HFC, follow NXP's QorIQ P2020 reference-design checklist: provide local decoupling on every VDDCORE/VTT rail, follow the DDR3 layout guidelines in the hardware specification (matched-impedance fly-by topology), and use the JTAG/COP interface for bring-up. Firmware development typically uses Linux (mainline support is mature) or VxWorks with NXP SDK 2.0. This page synthesizes distributor pricing, lifecycle/EOL status, drop-in alternatives within the QorIQ P1/P2 pin-compatible family, and practical design notes not consolidated in the manufacturer datasheet.

询价 联系我们
P2020NXE2HHC - QorIQ Dual-Core 1.2GHz Power Arch SoC | NXP
P2020NXE2HHC

P2020NXE2HHC - QorIQ Dual-Core 1.2GHz Power Arch SoC | NXP

The NXP P2020NXE2HHC is a QorIQ communications processor built on the Power Architecture e500v2 core, delivering dual-core 1.2 GHz performance with hardware cryptographic acceleration. Housed in a 689-pin TE-PBGA II (31x31 mm) package with exposed thermal pad, this SoC integrates DDR2/DDR3 memory controllers with ECC, Gigabit Ethernet, PCI Express, Serial RapidIO, USB, and an optional SEC security engine. The device is rated for the extended -40C to +125C automotive/industrial temperature range and targets networking, industrial, and embedded communications workloads where multi-protocol throughput and low power per watt are critical. A communications SoC (System-on-Chip) is a highly integrated microprocessor that consolidates CPU cores, memory interfaces, networking peripherals, and security accelerators into a single silicon die. QorIQ P-series SoCs sit at the top of the value-performance tier of NXP's Power Architecture portfolio, scaling from the single-core P1011 at 533 MHz up through the dual-core P2020 at 1.2 GHz, all in pin-compatible packages. This scalability allows OEMs to reuse a single PCB design across multiple product lines by simply swapping the SoC. Key specifications include dual Power Architecture e500v2 cores at 1.2 GHz, 32 KB instruction / 32 KB data L1 cache per core, a unified 256 KB L2 cache, dual DDR2/DDR3 controllers with ECC, three Gigabit Ethernet ports with IEEE 1588 support, three PCI Express Gen 1/Gen 2 controllers, two Serial RapidIO ports, two USB 2.0 controllers with PHY, and an integrated SEC 4.0 security engine for IPsec, SSL/TLS, and 3GPP cryptographic acceleration. The 45nm process node delivers strong performance per watt for thermally constrained fanless embedded enclosures. The P2020NXE2HHC architecture is widely deployed in industrial routers, multi-service access equipment, factory automation controllers, military/aerospace networking, and defense-grade secure communications platforms. Its integrated SEC engine makes it well suited for IPsec VPN gateways, SSL offload appliances, and trusted computing applications where hardware-accelerated cryptography is required. When designing with this part, ensure adequate thermal relief on the TE-PBGA II exposed pad, validate DDR3 signal integrity with 4+ layer PCB stack-ups, and follow NXP's reference PCB layout for the SERDES lanes. The part is in active EOL/Last Time Buy transition; confirm RoHS/REACH compliance at order entry. Use NXP CodeWarrior or Linux BSP packages for software development.

询价 联系我们
P2020PSE2HZB - QorIQ P2 Dual-Core 1.2GHz MPU | NXP
P2020PSE2HZB

P2020PSE2HZB - QorIQ P2 Dual-Core 1.2GHz MPU | NXP

The NXP P2020PSE2HZB is a dual-core PowerPC e500v2 communications microprocessor from the QorIQ P2 family, operating up to 1.2 GHz core frequency in a 689-pin TEPBGA II (31x31 mm) package. It integrates dual e500 cores built on Power Architecture technology with 32-bit datapath support, designed for networking infrastructure, telecom, industrial control, medical imaging, telehealth, aerospace and defense, and test and measurement applications. A microprocessor (MPU) is the central processing unit of an embedded system, integrating one or more CPU cores, cache hierarchies, memory controllers, and peripheral interfaces. Within the broader taxonomy, an MPU sits above microcontroller units (MCUs) in performance and is commonly architected for high-throughput data-plane workloads. The QorIQ P2 platform evolved from Freescale's PowerQUICC communications processors, targeting wire-speed packet processing in routers, switches, and secure gateways. Key features of the P2020PSE2HZB include dual e500v2 cores at 1.2 GHz, integrated security engine, DDR3 memory controller with ECC support, multiple Gigabit Ethernet interfaces, PCIe and Serial RapidIO connectivity, and enhanced peripheral bus architecture. The communications-centric integration reduces BOM count for line-card designs while preserving software compatibility with the broader QorIQ family. Architecturally, the P2020PSE2HZB leverages the e500v2 core with dual-issue superscalar pipeline, hardware table lookup assist, and integrated SEC engine for cryptographic offload. The platform supports symmetric and asymmetric cryptography, pattern matching, and bulk data encryption, making it suitable for IPSec, SSL/TLS termination, and IPsec VPN gateway applications. Typical applications include multi-service routers, secure VPN gateways, LTE base station controllers, industrial automation controllers, medical imaging processors, and aerospace mission computers. The dual-core architecture delivers parallel processing of control-plane and data-plane tasks within a single chip. When designing with this MPU, ensure proper thermal management for the TEPBGA II package - at full 1.2 GHz dual-core load, consider junction-to-ambient thermal resistance and use at least a four-layer PCB with thermal vias beneath the exposed die area. The platform requires a pre-boot loader or JTAG programmer for initial firmware development. This page synthesizes distributor pricing, drop-in same-family alternatives, thermal guidance, and detailed comparison tables that augment the information gain over the manufacturer datasheet and standard distributor listings.

询价 联系我们
P2040NSE1MMB - QorIQ P2040 4-Core 1.2GHz PowerPC MPU | NXP
P2040NSE1MMB

P2040NSE1MMB - QorIQ P2040 4-Core 1.2GHz PowerPC MPU | NXP

The NXP P2040NSE1MMB is a PowerPC e500mc microprocessor from NXP's QorIQ P2 family, integrating four 32-bit cores running at up to 1.2 GHz in a 780-pin FCPBGA (23x23 mm) package. The device targets enterprise and service-provider networking workloads including control-plane processing, line-card aggregation, and software-defined networking. The 'NSE1' suffix denotes the standard 0 to 105 °C commercial temperature grade; the 'MMB' suffix encodes the 1.2 GHz core frequency and r1.1 silicon revision. A microprocessor (MPU) is a single-chip CPU that integrates one or more processor cores, caches, memory controllers, and a rich set of system I/O on a single die. Within the broader computing hierarchy, an MPU sits between a microcontroller (typically lower-power, integrated peripherals, single-tasking) and a high-end server CPU (multi-socket, out-of-order, NUMA). The QorIQ family belongs to the embedded networking segment, where deterministic performance, low power, and integrated high-speed SerDes are critical. The P2040NSE1MMB features four e500mc cores with dual-issue pipelines, integrated L1/L2 caches, a 64-bit DDR3/DDR3L memory controller, three PCIe Gen 2 controllers, multiple 10 GbE and 1 GbE Ethernet MACs, SATA, USB, and a flexible SerDes-based I/O fabric. Hardware virtualization and trusted-boot features (per the QorIQ Security Engine) are supported. The integrated datapath accelerators (DPAA) provide packet parsing, queuing, and crypto offload, allowing line-rate processing on multi-gigabit interfaces without burdening the cores. Typical applications include multi-service routers, LTE/4G base-station baseband, IP-PBX/media gateways, enterprise switches, and industrial control. The software ecosystem supports standard Linux, VxWorks, and Green Hills INTEGRITY, with NXP CodeWarrior and the QorIQ Linux SDK providing toolchain and board-support packages. P2040 software is upward-compatible with the P3, P4, and P5 QorIQ families, enabling customer code reuse across product tiers. When designing with the P2040NSE1MMB, engineers should plan thermal management for the 23x23 mm BGA; consult the Freescale/NXP Hardware Specification for the recommended 8-layer PCB stack-up, decoupling, and boundary-scan/JTAG access. Pin-compatible variants such as the P2041 (additional features) and frequency-scaled bins (1000 MHz) allow system tuning without re-laying-out the PCB. This page synthesizes distributor pricing from DigiKey/Mouser/Octopart, parametric drop-in alternatives, and practical hardware-design guidance not found in the bare manufacturer datasheet.

询价 联系我们
P2040NSE7HLC - QorIQ Quad-Core 1.2GHz SoC | NXP FCBGA-780
P2040NSE7HLC

P2040NSE7HLC - QorIQ Quad-Core 1.2GHz SoC | NXP FCBGA-780

The NXP (formerly Freescale) P2040NSE7HLC is a QorIQ quad-core 64-bit Power Architecture system-on-chip (SoC) operating at up to 1.2 GHz, housed in a 780-ball FCBGA package. It integrates four Power Architecture e500mc cores with dual DDR3/3L memory controllers, hardware-accelerated security (SEC), and a rich I/O subsystem including PCIe, SATA, Serial RapidIO (SRIO), and 1G/10 Gigabit Ethernet MACs, all in a 23 x 23 mm footprint. A QorIQ processor is a communications-focused multicore SoC built on the Power Architecture instruction set, designed for networking, telecom, and data-plane workloads where deterministic throughput, deep packet inspection, and integrated high-speed I/O matter more than raw single-thread performance. P2040 sits in NXP's low-end to mid-range quad-core tier, bringing P4-class architectural features (such as the Corenet-Platform fabric and hardware virtualization) down to cost- and power-sensitive routers, line cards, and industrial control platforms. Key features include four e500mc cores at 800 MHz to 1.2 GHz, dual 64-bit DDR3/3L controllers with ECC supporting up to 8 GB of addressable memory, three PCIe Gen2 controllers, two SATA 2.0 ports, three SRIO lanes, four 1 GbE MACs plus a 10 GbE MAC, an integrated security engine (SEC 4.2) with public-key and symmetric accelerators, and a thermal monitor that allows operation from 0°C to 105°C (Tcase). The P2040 uses a coherent CoreNet fabric that links the cores, I/O, and memory controllers on a single on-die switch, eliminating the northbridge/southbridge split of older PowerQUICC designs. This simplifies board layout and reduces latency between cores and peripherals, while the FCBGA-780 package provides a 23 x 23 mm body with 0.8 mm ball pitch suitable for high-density 12+ layer PCBs with buried vias. Typical applications include multi-service routers, broadband access gateways, line-card controllers in modular chassis, LTE/UMTS base-station baseband, network-attached storage, and industrial Ethernet switches. The integrated SEC engine also makes the P2040 attractive for IPsec/SSL acceleration in VPN concentrators. The P2040 is pin-compatible with the single-core P2020 and the dual-core P2010, enabling OEM scaling without board rework. When designing with this part, allocate at least 12 PCB layers for the FCBGA-780 break-out, follow NXP's AN4325 routing guidelines for DDR3, and provide sufficient bulk capacitance near the core and platform voltage rails (Vdd and GVDD). Note that the part is marked End-of-Life on NXP's product page; ensure long-term availability before committing to new designs, or evaluate the LS1043A/LS1046A Layerscape family as a roadmap replacement.

询价 联系我们
P2040NSN1HLB - QorIQ P2 Quad-Core 800MHz | NXP
P2040NSN1HLB

P2040NSN1HLB - QorIQ P2 Quad-Core 800MHz | NXP

The NXP P2040NSN1HLB is a quad-core PowerPC e500mc microprocessor from the QorIQ P2 family, operating at 800 MHz with a 32-bit architecture and packaged in a 780-FCPBGA (23x23 mm). It supports an industrial temperature range of 0°C to 105°C and is a Non-ENC (non-encryption) variant targeted at networking infrastructure designs that do not require integrated cryptographic acceleration. A QorIQ communications processor is a multicore Power Architecture SoC designed for high-performance packet processing, switching, and routing. It belongs to a broader hierarchy of communications SoCs, which themselves sit within the application-specific standard products (ASSP) class of semiconductors. The P2 family scales between 1 and 4 cores, and the P2040 sits at the top of that range with four cores sharing a coherent fabric. Key features of the P2040NSN1HLB include four e500mc cores with hardware hypervisor and virtualization support, integrated DDR3/3L memory controller, multiple Gigabit Ethernet interfaces, PCI Express Gen2 controllers, and SerDes lanes for flexible high-speed interconnect. The device is software-compatible with members of the P1 family and all devices in the P3, P4, and P5 QorIQ families, allowing customers to scale the same software stack across multiple performance points. Architecturally, the P2040 combines an advanced core complex, a CoreNet platform cache, and a high-bandwidth interconnect fabric. This design delivers balanced compute, memory, and I/O bandwidth required by line-rate packet processing workloads. Security services (SEC) and pattern matching engines are present in the silicon but the Non-ENC suffix indicates the cryptographic block is disabled, distinguishing this SKU from SEC-enabled P2040 variants. Typical applications include enterprise routers, Ethernet switches, wireless base station controllers, network attached storage, industrial control gateways, and unified threat management appliances. The 0°C to 105°C operating range also suits outdoor and factory-floor networking equipment. When selecting this part, engineers should note the 800 MHz core frequency, the Non-ENC security profile, and the 780-FCPBGA package. The P2040 and P2041 share the same 780-FCPBGA footprint, simplifying board reuse between variants. This page synthesizes verified distributor availability, drop-in same-package alternatives, and a parameter-by-parameter comparison table that goes beyond the basic manufacturer product page, helping engineers select and source the right QorIQ SKU.

询价 联系我们
P2040NSN1MMB - QorIQ P2040 Quad-Core 1.2GHz MPU | NXP
P2040NSN1MMB

P2040NSN1MMB - QorIQ P2040 Quad-Core 1.2GHz MPU | NXP

The NXP P2040NSN1MMB is a QorIQ P2040 quad-core communications microprocessor built on the Power Architecture e500mc core, operating at up to 1.2 GHz with a 32-bit datapath, and packaged in a 780-pin FCPBGA (23x23 mm). It combines four high-performance Power Architecture cores with hardware data-path acceleration logic and a rich set of networking and peripheral bus interfaces, targeting networking, telecom/datacom, wireless infrastructure, and aerospace/defense applications. What is an MPU? A microprocessor (MPU) is the central processing unit of an embedded system, integrating the CPU cores, cache hierarchy, memory controller, and peripheral interfaces on a single die. The P2040 belongs to the broader QorIQ communications processor family, which itself sits within the Power Architecture embedded processor taxonomy. This positions the P2040 between application processors (rich OS, multimedia) and microcontrollers (real-time, deterministic I/O), making it suitable for data-plane and control-plane workloads in networking equipment. Key differentiating features include the four e500mc cores with hardware multithreading support, integrated 10 Gigabit Ethernet and Gigabit Ethernet controllers, a high-speed DDR3/DDR3L memory controller, multiple PCI Express Gen2 controllers, and dedicated hardware blocks for frame management, queue management, and encryption acceleration. The part operates across a -40C to +105C industrial temperature range and includes a security engine with optional encryption, distinguishing it from the higher-speed P2041 variant. Architecturally, the P2040 uses a coherent SMP fabric that shares a unified L2 cache across cores, enabling symmetric multiprocessing with hardware cache coherency. The integrated datapath acceleration engines (Frame Manager, Queue Manager, Security Engine) offload packet classification, buffer management, and crypto operations from the cores, freeing CPU cycles for control-plane tasks. Compared to discrete CPU-plus-assistant-chip designs, the P2040 reduces BOM, board area, and software complexity. Typical applications include enterprise and service-provider routers and switches, LTE base-station baseband and control cards, network-attached storage controllers, industrial gateways, and aerospace mission computers. The quad-core scalability and rich I/O portfolio also make it attractive for software-defined networking (SDN) and network functions virtualization (NFV) platforms where deterministic throughput is required. When designing with this device, plan thermal dissipation around the 23x23 mm BGA footprint: provide adequate PCB copper and airflow to keep junction temperature below the +105C limit. Use the NXP CodeWarrior or Linux SDK toolchain, and validate DDR3 signal integrity with the manufacturer's reference design layout. This page synthesizes distributor pricing, drop-in P2040-family alternatives, and practical design guidance that complements the manufacturer datasheet and helps engineers shorten the selection cycle.

询价 联系我们
P2040NSN7FLC - QorIQ Quad-Core 667MHz SoC, FCPBGA-780 | NXP
P2040NSN7FLC

P2040NSN7FLC - QorIQ Quad-Core 667MHz SoC, FCPBGA-780 | NXP

The NXP P2040NSN7FLC is a QorIQ P2040 quad-core 32-bit Power Architecture system-on-chip (SoC) operating at up to 667 MHz per core, packaged in a 780-pin FCPBGA (23x23 mm). It integrates four e500mc cores with a high-performance datapath, hardware-accelerated packet parsing, and a rich I/O subsystem targeting networking, industrial, and military/aerospace applications. A QorIQ SoC is a multi-core communications processor that combines CPU cores, cache coherency fabric, and high-speed serial interfaces (SerDes) on a single die. It sits in the hierarchy: SoC -> microprocessor -> communications processor -> embedded processor -> semiconductor, and is widely used in routers, switches, and line cards where deterministic packet throughput and hardware offload matter as much as raw compute. The P2040 extends the high-end P4080/P4040 architecture down into the mid-range quad-core space while preserving software compatibility with P1, P3, P4, and P5 families. Key features include four e500mc cores at 667 MHz, a 256 KB shared L2 backside cache per cluster, integrated DDR3/DDR3L controller with ECC support, four x4 Serial RapidIO (SRIO) controllers, two PCIe Gen2 controllers, two SATA 2.0 controllers, and four Gigabit Ethernet MACs supporting 1 GbE and 10 GbE operation. The device supports hardware virtualization, queuing, and parse/classify/distribute acceleration, offloading critical networking tasks from the cores. The 780-pin FCPBGA (23x23 mm) package exposes a high-lane-count SerDes interface that delivers up to 30 Gbps of aggregate I/O bandwidth. The 45 nm process technology balances performance and power, with the P2040NSN7FLC variant specified for 0 C to 105 C operation and is a Rev 2 silicon revision. Typical applications include enterprise routers and switches, network attached storage (NAS), security appliances, industrial control platforms, and military/aerospace embedded computing. P2040 and P2041 are pin-compatible within the same 23 x 23 mm package, allowing designers to scale performance by swapping the SoC without board rework. When designing with this part, plan the PCB stack-up and power-rail sequencing carefully: the FCPBGA-780 package requires high-layer-count boards (typically 10+ layers) with matched-length SerDes routing. Thermal management is also critical at full 667 MHz across four cores - a heatsink or thermal pad is normally mandatory. This page synthesizes authorized distributor pricing, Rev 2 silicon variants, and pin-compatible P2041 alternatives that are not consolidated on a single NXP product page.

询价 联系我们
P2040NSN7KLC - QorIQ P2040 4-Core 1GHz PowerPC MPU | NXP
P2040NSN7KLC

P2040NSN7KLC - QorIQ P2040 4-Core 1GHz PowerPC MPU | NXP

The NXP P2040NSN7KLC is a QorIQ P2040 quad-core communications microprocessor featuring four Power Architecture e500mc cores running at up to 1.0 GHz, integrated in a 780-ball FC-PBGA (23x23 mm) package. The part combines high-performance data path acceleration with networking and peripheral bus interfaces required for networking, telecom/datacom, wireless infrastructure, and aerospace applications. What is a QorIQ communications processor? The QorIQ platform is NXP's family of Power Architecture-based multicore processors designed for intelligent networking and embedded infrastructure workloads. Within the taxonomy, the QorIQ P2040 sits in the low-end to mid-range quad-core tier, software-compatible with the P1 family and all devices in the P3, P4, and P5 families, enabling customers to scale software up and down the product line. Key features of the P2040NSN7KLC include four e500mc 32-bit cores, integrated DDR3/3L memory controller with ECC, dual 10 Gigabit Ethernet (XAUI) plus multiple Gigabit Ethernet interfaces, two PCI Express Gen 2 controllers, two Serial RapidIO 2.0 ports, and hardware acceleration for packet parsing, classification, and security. The processor supports hardware virtualization and symmetric/asymmetric multiprocessing. The P2040 architecture leverages the e500mc core with dual-issue, out-of-order execution, and integrated L1/L2 caches with ECC. Integrated datapath accelerators handle buffer management and queue management, offloading housekeeping from the cores and improving packet throughput. The platform integrates SerDes lanes for flexible interface configuration (SRIO, PCIe, sGMII, SGMII, XAUI, etc.). Typical applications include enterprise and edge routers, LTE/Wi-Fi base stations, network-attached storage controllers, industrial control and factory automation, military/aerospace secure networking, and secure IoT gateways. The P2040NSN7KLC variant operates up to 1.0 GHz and is the standard commercial-grade ordering part number for the 780-FCPBGA package. When designing with this device, allocate sufficient PCB real estate for the 23x23 mm BGA and ensure a 12+ layer stackup with matched-impedance routing for DDR3, SerDes, and XAUI. Reference the NXP P2040 Hardware Specifications document for thermal design, power sequencing, and JTAG/debug requirements; this part requires firmware (UBoot) and a board support package to boot. This page synthesizes distributor stock, end-of-life status, recommended same-family drop-in alternatives, and practical design notes that go beyond the manufacturer datasheet alone.

询价 联系我们
P2040NXN1FLB - QorIQ P2040 4-Core 667MHz e500mc MPU | NXP
P2040NXN1FLB

P2040NXN1FLB - QorIQ P2040 4-Core 667MHz e500mc MPU | NXP

The NXP P2040NXN1FLB is a quad-core PowerPC e500mc microprocessor in the QorIQ P2 communications processor family, delivering up to 667 MHz per core in a 780-pin FCPBGA (23x23 mm) package with industrial -40C to +105C temperature grade. Built on a low-power 45 nm process, it integrates four high-performance e500mc cores with 32 KB I-cache and 32 KB D-cache per core, plus a shared 256 KB CoreNet Platform Cache, making it suitable for demanding wired and wireless networking workloads. The device is the non-encryption, 667 MHz speed-grade variant of the P2040 family, targeted at cost-sensitive applications that do not require the on-chip SEC engine. A communications processor is a system-on-chip (SoC) class microprocessor designed for packet processing, traffic management, and secure networking functions in routers, switches, base stations, and similar infrastructure. Within the broader taxonomy, it sits at the intersection of microprocessor (MPU), network processor, and embedded SoC. QorIQ P-series devices sit below the P3/P4/P5 high-end families but above the entry-level QorIQ LS series, and the P2040/P2041 pair bridges into the quad-core segment with the architectural heritage of the higher-tier P4080 platform. Key differentiating features of the P2040NXN1FLB include four e500mc cores running at 667 MHz, a high-bandwidth CoreNet coherency fabric, three PCIe Gen 2 controllers, two 10 Gigabit Ethernet (XAUI) plus eight 1 Gigabit Ethernet (SGMII) MACs, four SerDes lanes configurable across multiple protocols, integrated security (without SEC engine in the NX variant), and a 32-bit DDR3 memory controller with ECC support. Hardware-accelerated queue and buffer management, pattern matching, and table lookup engines are also integrated for offloading common networking data-plane tasks. Architecturally, the P2040 uses a coherency fabric connecting private L2 caches to a shared platform cache and to the I/O and memory subsystems, allowing all four cores to share data without software intervention. The e500mc core is a superscalar, out-of-order Power Architecture implementation with hardware virtualization support and a memory management unit that enables full Linux and VxWorks deployments. Integrated networking accelerators offload packet parsing, classification, and queue management, dramatically improving packets-per-second throughput versus general-purpose CPUs. Typical applications include enterprise and SMB routers, unified threat management (UTM) appliances, wireless LAN controllers, multi-service access nodes, industrial control gateways, and single-board computers for networking infrastructure. The wide I/O mix (PCIe, XAUI, SGMII, USB, SATA, SDHC, SPI, I2C, UART, GPIO) and the dual-core / quad-core scalability make it a flexible choice for mid-range networking and industrial platforms. When designing with this part, ensure the 780-pin FCPBGA package uses a high-layer-count PCB (typically 8+ layers) with controlled-impedance SerDes routing, matched-length DDR3 traces, and an adequate thermal solution. The 667 MHz NX speed-grade is the lowest-cost variant of the P2040; designers should choose the encrypted or higher-speed variants when SEC or higher throughput is required. Industrial temperature grade (-40C to +105C) supports harsh-environment deployments. This page synthesizes distributor pricing, drop-in NXP and cross-brand QorIQ alternatives, application guidance, and design notes not found in the manufacturer datasheet alone, providing a practical reference for embedded engineers evaluating the P2040NXN1FLB.

询价 联系我们
P2041NSE1MMB - QorIQ P2 Quad-Core 1.2GHz PowerPC MPU | NXP
P2041NSE1MMB

P2041NSE1MMB - QorIQ P2 Quad-Core 1.2GHz PowerPC MPU | NXP

The NXP P2041NSE1MMB is a quad-core PowerPC e500mc microprocessor in the QorIQ P2 platform, delivering four 32-bit cores at 1.2 GHz inside a 780-ball FCP-BGA (FCPBGA-780, 23x23 mm) package. According to NXP's QorIQ P2040/P2041 platform documentation, the P2041 integrates four high-performance e500mc cores with a shared 256 KB L2 cache, three tri-speed Ethernet controllers supporting up to 10 GbE, four PCIe Gen2 controllers, two SATA ports, USB 2.0, and dual DDR3 memory controllers. A microprocessor (MPU) is a single-chip CPU that integrates the arithmetic logic unit, control unit, registers, and often cache and peripherals. Unlike microcontrollers (MCU), MPUs target applications needing high-speed external-memory throughput and high-bandwidth I/O, sitting at the top of the embedded processing hierarchy: MPU -> microprocessor -> processor -> semiconductor. The QorIQ P2 family extends the P4 architecture into lower-cost, lower-power quad-core designs. The P2041NSE1MMB operates on a 1.0V core / 1.5-1.8V / 2.5V / 3.3V I/O supply scheme, supports encrypted secure-boot (the SE1 suffix), and runs the 0 to 105C commercial temperature grade. It is software-compatible with the P1, P3, P4, and P5 QorIQ families, allowing porting of existing PowerQUICC and QorIQ firmware. Security features include Trust Architecture 1.1 and on-chip cryptography acceleration (SEC engine). Architecturally the P2041 uses a coherent SMP fabric connecting four e500mc cores to memory and I/O. The e500mc adds hardware virtualization (hypervisor mode) and SIMD-style multimedia extensions beyond the older e500 core, enabling broader workload consolidation. Each core has its own 32 KB I-cache and 32 KB D-cache; the platform's 256 KB L2 is shared and configurable per NXP's platform guide. Typical applications include multi-service routers, LTE/WiMAX base-station baseband, enterprise switches, network-attached storage controllers, industrial control planes, and military/aerospace SBCs. The wide I/O mix also makes the P2041 viable for medical imaging and software-defined radio front ends. When designing with the P2041NSE1MMB, plan for a multi-rail DC/DC tree (1.0V, 1.5/1.8V, 2.5V, 3.3V) and a large PCB escape region under the FCPBGA-780 to fan out DDR3 to 780 balls. JTAG/cOP access is required for bring-up; Trust 1.1 secure boot must be provisioned before production firmware is deployed. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

询价 联系我们