微控制器

产品（18732)

ATMEGA88PB-MUR - 8-bit AVR MCU 8KB Flash 20MHz QFN-32 | Microchip
ATMEGA88PB-MUR

ATMEGA88PB-MUR - 8-bit AVR MCU 8KB Flash 20MHz QFN-32 | Microchip

The Microchip Technology ATMEGA88PB-MUR is an 8-bit AVR RISC microcontroller with picoPower technology, combining 8 KB ISP Flash (4K x 16), 512 B EEPROM, and 1 KB SRAM, running at up to 20 MHz in a 32-pin VFQFN (5x5 mm) package with exposed pad. An 8-bit AVR microcontroller is a Harvard-architecture RISC MCU in the broader microcontroller and embedded-processor hierarchy. AVR cores execute most instructions in a single clock cycle, and ATmega-family devices integrate Flash program memory, SRAM, EEPROM, timers, and analog peripherals on a single die, serving as the main compute element in embedded control systems. Key features include 27 general-purpose I/O lines, 32 general-purpose working registers, three flexible timer/counters with compare modes, a 10-bit ADC, USART with start-of-frame wake-up, and two-wire (I2C) and SPI serial interfaces. The picoPower technology delivers low active and sleep currents for battery-operated designs, and the part is positioned for Functional Safety (FuSa) documentation support per Microchip. The advanced AVR RISC architecture achieves throughputs close to 1 MIPS per MHz, allowing a 20 MHz clock to deliver roughly 20 MIPS of processing performance. In-system programmable Flash with read-while-write support enables field firmware updates, while the debugWIRE on-chip debug interface uses only a single pin for development. Typical applications include industrial automation nodes, battery-powered sensors and IoT end devices, consumer appliance control, and motor control auxiliaries, where the combination of 8 KB Flash and low-power sleep modes fits cost- and power-sensitive designs. When designing with the QFN-32 (5x5 mm) package, connect the exposed center pad to a solid ground plane for thermal and electrical performance, and decouple VCC and AVCC with 100 nF ceramic capacitors placed close to the pins. This page synthesizes distributor pricing, drop-in ATmega-family alternatives, pinout data, and practical design notes not found on the manufacturer product page.

询价 联系我们
ATMEGA88PV-10AU - 8KB Flash 10MHz AVR MCU | Microchip
ATMEGA88PV-10AU

ATMEGA88PV-10AU - 8KB Flash 10MHz AVR MCU | Microchip

The Microchip Technology ATMEGA88PV-10AU is a picoPower 8-bit AVR RISC microcontroller delivering 8KB (4K x 16) of self-programming ISP Flash memory, 1KB SRAM, 512B EEPROM, and up to 10 MHz operation at 1.8V to 5.5V supply, housed in a 32-pin TQFP (7x7 mm, 0.8 mm pitch) package. An 8-bit microcontroller is a single-chip processor that executes application code, manages peripherals, and interfaces with sensors and actuators on one die. Within the power-management hierarchy of an embedded system, the MCU is the top-level controller that orchestrates power sequencing, communication, and sensing, making it the central semiconductor of most embedded designs. Key features include 131 mostly single-cycle AVR instructions achieving up to 10 MIPS at 10 MHz, 23 general-purpose I/O lines, an 8-channel 10-bit ADC, a serial USART, two-wire interface (I2C), SPI, and three flexible timers/counters including one 16-bit timer. The picoPower technology provides multiple sleep modes with very low standby current, and debugWIRE enables on-chip debugging over the reset line. Architecturally, the ATmega88PV uses the AVR enhanced RISC core with 32 general-purpose working registers directly connected to the ALU, allowing two independent registers to be accessed in one instruction executed in one clock cycle. Read-while-write Flash allows program memory updates while executing, supporting boot-loader based field upgrades. Typical applications include industrial sensor nodes, consumer appliance control, battery-powered instruments, and motor control panels. The wide 1.8V to 5.5V operating range and picoPower sleep modes fit battery and energy-harvesting designs directly. Design consideration: at 5V the device tolerates higher clock rates, but at 1.8V the safe maximum frequency is substantially lower, so derate system clock versus supply voltage per the datasheet speed-grade curves. This page synthesizes distributor pricing, drop-in alternatives, pinout, and practical design notes beyond the manufacturer datasheet for faster engineering decisions.

询价 联系我们
ATMEGA88PV-10MU - 8KB AVR MCU, 10MHz, 1.8-5.5V | Microchip
ATMEGA88PV-10MU

ATMEGA88PV-10MU - 8KB AVR MCU, 10MHz, 1.8-5.5V | Microchip

The Microchip Technology ATMEGA88PV-10MU is a high-performance, low-power 8-bit AVR ATmega microcontroller with 8KB of In-System Programmable FLASH (4K x 16), 512B EEPROM, 1KB SRAM, and a maximum clock speed of 10MHz, operating from a 1.8V to 5.5V supply and housed in a 32-pin VQFN (5x5 mm) package. An 8-bit microcontroller is an integrated circuit that combines a processor core, memory, and peripherals such as timers, UARTs, and ADCs on a single chip, forming the lowest tier of the embedded processing hierarchy (microcontroller -> embedded processor -> semiconductor). The AVR architecture uses a Harvard structure with 32 general-purpose working registers directly connected to the ALU, so most instructions execute in a single clock cycle, delivering up to 10 MIPS at 10MHz. Key features include 130 powerful RISC instructions, 23 programmable I/O lines, three flexible timers/counters with compare modes (two 8-bit, one 16-bit), a 10-bit ADC with 6 multiplexed channels, and I2C, SPI, and UART/USART serial interfaces. The picoPower V variant supports 1.8V operation, making it well suited to battery-powered designs. Technically, the device offers multiple sleep modes (Idle, ADC Noise Reduction, Power-save, Power-down, Standby, Extended Standby), in-system programmability (ISP) via SPI, and on-chip debug through debugWIRE on the RESET pin. Program memory is organized with read-while-write support, and the enhanced flash endurance exceeds 10,000 write cycles, with EEPROM endurance of 100,000 cycles. Typical applications include industrial control systems, battery-powered sensor nodes, home automation, motor control, and consumer appliances where low voltage and low power are prioritized over raw clock speed. A key design consideration is clock selection: at 1.8V the device is limited to 10MHz, so choose the calibrated internal RC oscillator or a conservative external crystal and verify supply voltage across the full operating range. This page synthesizes distributor pricing, drop-in alternatives, pinout data, and practical design notes not found in a single manufacturer datasheet, with pricing as of 2026-09-19.

询价 联系我们
ATMEGA88PV-10MUR - 8KB AVR MCU 1.8V 10MHz QFN-32 | Microchip
ATMEGA88PV-10MUR

ATMEGA88PV-10MUR - 8KB AVR MCU 1.8V 10MHz QFN-32 | Microchip

The Microchip Technology ATMEGA88PV-10MUR is a low-power 8-bit AVR RISC microcontroller with 8KB (4K x 16) self-programming Flash memory, 512B EEPROM, 1KB SRAM, an 8-channel 10-bit ADC, and a maximum clock frequency of 10MHz, housed in a 32-pin VQFN (5x5 mm) package with exposed pad. An 8-bit microcontroller is an integrated circuit that combines a processor core, memory, and peripherals on a single chip, executing one instruction per fetch cycle to control embedded systems. The ATmega family sits within Microchip's broader AVR product line, which is itself part of the microcontroller and embedded power-management hierarchy. These MCUs are the backbone of cost-sensitive control applications where a full application processor is unnecessary. Key features include the advanced RISC architecture with 131 powerful instructions, most of which execute in a single clock cycle, delivering up to 10 MIPS throughput at 10MHz. The wide operating voltage range of 1.8V to 5.5V supports battery-powered designs, while debugWIRE on-chip debugging reduces development cost by reusing the reset pin. The self-programming Flash enables in-system firmware updates. Technically, the device integrates a Harvard-architecture core with separate program and data buses, hardware multiplier, 24 external interrupt sources, and an analog comparator, making it efficient for real-time control loops and sensor acquisition tasks. Typical applications include consumer appliance control, industrial sensor nodes, battery-powered metering, and hobby/embedded prototyping where 1.8V operation and low cost are priorities. When designing with this MCU, remember the 10MHz speed grade restricts the safe clock at low voltages; at 1.8V the maximum frequency must be derated per the datasheet frequency-versus-voltage curve. This page synthesizes distributor pricing, drop-in same-family alternatives, pinout data, and practical design notes not found in the manufacturer datasheet.

询价 联系我们
ATMEGA88PV-10PU - AVR 8-bit MCU 8KB Flash 10MHz DIP-28 | Microchip
ATMEGA88PV-10PU

ATMEGA88PV-10PU - AVR 8-bit MCU 8KB Flash 10MHz DIP-28 | Microchip

The Microchip (Atmel) ATMEGA88PV-10PU is a picoPower AVR 8-bit RISC microcontroller with 8 KB In-System Programmable Flash, 512 B EEPROM, 1 KB SRAM, 23 general-purpose I/O lines, and a 10 MHz maximum clock, supplied in a 28-pin PDIP package rated from 1.8 V to 5.5 V across the industrial temperature range. An 8-bit microcontroller is a single-chip computer that integrates a CPU, program memory, data memory, timers, and serial peripherals on one die. Within the power-management and embedded-systems hierarchy, it sits at the node level of a control system, executing firmware that sequences sensors, actuators, and communication links. The AVR family uses an enhanced RISC architecture with 130 powerful instructions, most executing in a single clock cycle, giving near-MIPS-per-MHz throughput. Key features of the ATMEGA88PV-10PU include read-while-write Flash for safe in-field firmware updates, 32 general-purpose working registers directly connected to the ALU, three flexible timer/counters with compare modes, a byte-oriented Two-Wire Interface (I2C-compatible), an SPI serial port, and a programmable serial USART. The picoPower technology delivers very low sleep-mode consumption, valuable in battery-powered designs. Architecturally, the device pairs the AVR core with a Harvard memory bus, separate program and data paths, single-cycle I/O access, and an on-chip debug capability via debugWIRE. Program memory maps as 4K x 16 words, and the internal RC oscillator plus brown-out detector and watchdog reduce external component count. Typical applications include industrial sensor nodes, consumer appliance controls, motor-driven toys and hobby platforms such as Arduino-class boards, and low-cost instrumentation front ends where 5 V DIP packaging simplifies prototyping and hand assembly. Design consideration: the 10 MHz speed grade allows safe operation at the full 1.8 V to 5.5 V supply range; for 20 MHz operation you must move to the ATmega88-20 versions, which restrict supply options. This page synthesizes distributor availability, drop-in family alternatives, pinout data, and practical design notes in one place, beyond what a single datasheet page provides.

询价 联系我们
ATMEGA88V-10AI - 8-bit AVR MCU 8KB Flash 10MHz TQFP-32 | Microchip
ATMEGA88V-10AI

ATMEGA88V-10AI - 8-bit AVR MCU 8KB Flash 10MHz TQFP-32 | Microchip

The Microchip (Atmel) ATMEGA88V-10AI is a low-power 8-bit AVR RISC microcontroller with 8KB in-system programmable Flash, 1KB SRAM, 512B EEPROM, and a 10 MHz maximum clock frequency, housed in a 32-pin TQFP (7x7 mm) package rated for industrial temperatures of -40C to +85C. An 8-bit AVR microcontroller is a Harvard-architecture processor that executes most instructions in a single clock cycle, delivering approximately 1 MIPS per MHz of throughput. Within the power-management hierarchy of embedded systems, the ATmega88 family sits in the mid-range tier of the AVR ATmega line, above the tinyAVR parts and below the ATmega328, and integrates CPU, program memory, data memory, timers, analog-to-digital conversion, and serial peripherals on a single silicon die. Key features include 131 powerful instructions with mostly single-cycle execution, 23 general-purpose I/O lines, three flexible timer/counters with compare modes, a 10-bit 8-channel ADC, a byte-oriented Two-Wire Interface (I2C-compatible), a serial programmable USART, and an SPI interface. The picoPower-era low-power design supports 1.8V to 5.5V operation in the V-variant, enabling battery-powered designs. Technically, the ATmega88V-10AI combines the AVR enhanced RISC core with 32 general-purpose working registers directly connected to the ALU, allowing two independent registers to be accessed in one instruction. The self-programming Flash supports boot-loader-based field updates, while debugWIRE provides on-chip debugging over a single pin via the standard AVR ISP/debugWIRE toolchain in Atmel Studio / Microchip Studio. Typical applications include industrial sensor nodes, battery-powered metering, motor control with PWM timers, consumer appliance control panels, and low-cost data loggers. The wide 1.8V to 5.5V supply range directly fits two-cell battery stacks and 3.3V or 5V logic systems. Design consideration: the V speed grade limits maximum clock to 10 MHz across the full voltage range; if 20 MHz operation is required, choose the ATmega88-20AI speed grade instead, which shares the same TQFP-32 footprint. This page synthesizes distributor pricing, pin-to-pin alternatives, and practical design notes not found in the manufacturer datasheet.

询价 联系我们
ATMEGA88V-10AJ - 8-Bit AVR MCU, 8KB Flash, 10MHz | Microchip
ATMEGA88V-10AJ

ATMEGA88V-10AJ - 8-Bit AVR MCU, 8KB Flash, 10MHz | Microchip

The Microchip Technology ATMEGA88V-10AJ is a low-power 8-bit AVR RISC microcontroller with 8KB ISP Flash memory, 1KB SRAM, 512B EEPROM, 23 general-purpose I/O lines, and a maximum clock speed of 10MHz at a wide 1.8V to 5.5V operating voltage, packaged in a 32-pin TQFP (7x7 mm) enclosure. A microcontroller unit (MCU) is a complete computing system on a single chip, combining a processor core, program memory, data memory, and peripherals. The ATmega88V belongs to the ATmega48/88/168 family of AVR enhanced RISC MCUs, positioned within Microchip's broader 8-bit microcontroller portfolio, a class of semiconductors that dominates cost-sensitive embedded control tasks from appliance control to sensor nodes. Key features include 131 powerful instructions, most executed in a single clock cycle, delivering up to 20 MIPS throughput in the family at 20MHz; 10MHz maximum frequency for the V (low-voltage) speed grade across 1.8V to 5.5V operation; three flexible timer/counters with compare modes; a serial programmable USART; byte-oriented Two-Wire Interface (TWI/I2C); SPI serial interface; and an 8-channel 10-bit ADC. debugWIRE on-chip debugging is supported through the RESET pin, reducing external debug circuitry. Architecturally, the device uses an advanced Harvard-structured RISC core with 32 general-purpose working registers directly connected to the ALU, allowing two independent register accesses in a single instruction. Self-programming Flash with read-while-write support enables in-system reprogramming and bootloader applications without external programmers. Typical applications include low-power battery-operated sensor nodes exploiting the 1.8V floor, industrial control panels using the USART and TWI interfaces, and consumer appliance boards leveraging the 10-bit ADC for analog sensor acquisition. When designing with this part, remember the 10MHz limit applies across the full voltage range; do not swap in a 20MHz ATmega88 variant firmware assumption without verifying clock fusing and timing loops. This page synthesizes distributor pricing, drop-in alternatives, pinout data, and practical design notes not found in the manufacturer datasheet alone, all verified as of 2026-09-19.

询价 联系我们
ATMEGA88V-10AU - 8KB AVR 8-Bit MCU 10MHz | Microchip | TQFP-32
ATMEGA88V-10AU

ATMEGA88V-10AU - 8KB AVR 8-Bit MCU 10MHz | Microchip | TQFP-32

The Microchip Technology ATMEGA88V-10AU is an 8-bit AVR RISC microcontroller with 8 KB of in-system programmable Flash, 1 KB SRAM, and 512 B EEPROM, running at up to 10 MHz and housed in a 32-pin TQFP (7x7 mm) package. It operates from 1.8 V to 5.5 V and provides 23 general-purpose I/O lines. An AVR microcontroller is a Harvard-architecture 8-bit RISC device that executes most instructions in a single clock cycle, delivering up to 1 MIPS per MHz. Within the product taxonomy it sits under microcontrollers (MCU) -> integrated circuits -> semiconductors, and the ATmega family is the classic general-purpose branch of the AVR line, positioned between the tinyAVR and megaAVR performance tiers. Key features include 8 KB ISP Flash with read-while-write, 512 B EEPROM, 1 KB SRAM, 23 GPIO lines, three flexible timer/counters with compare modes, an 8-channel 10-bit ADC, a programmable USART, a byte-oriented Two-Wire Serial Interface (I2C), an SPI port, and debugWIRE on-chip debug. The picoPower design keeps active current low, making the device suitable for battery-powered and always-on embedded control. The ATmega88V is fabricated in Microchip's low-power CMOS process and uses the enhanced AVR RISC core with 32 general-purpose working registers. Because the core is clocked directly from the system clock with no divider penalty, throughput scales linearly with frequency, and the wide 1.8 V to 5.5 V supply range allows direct operation from single Li-Ion cells or regulated 3.3 V and 5 V rails without level shifting. Typical applications include industrial sensor nodes, consumer appliance control boards, battery-powered data loggers, motor and relay control, and legacy ATmega8/ATmega48 designs being migrated to a pin-compatible modern device. The 32-TQFP footprint is shared across the ATmega48/88/168 family, so firmware and layout can be reused across memory densities. When designing with this device, decouple every VCC/AVCC pin with a 100 nF ceramic capacitor placed within a few millimeters of the pin, and keep the AREF pin bypassed when the ADC is used. The 10 MHz maximum frequency at 1.8 V-5.5 V means the part is not a drop-in for 16 MHz or 20 MHz ATmega88 variants, which require at least 2.7 V or 4.5 V respectively. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet, giving engineers a single reference for procurement and layout decisions.

询价 联系我们
ATMEGA88V-10AUR - 8KB AVR MCU 10MHz 32-TQFP | Microchip
ATMEGA88V-10AUR

ATMEGA88V-10AUR - 8KB AVR MCU 10MHz 32-TQFP | Microchip

The Microchip Technology ATMEGA88V-10AUR is a picoPower 8-bit AVR RISC microcontroller with 8KB (4K x 16) ISP Flash memory, 1KB SRAM, 512B EEPROM, 23 general-purpose I/O lines and a 10 MHz maximum clock, housed in a 32-pin TQFP (7 x 7 mm, 0.8 mm pitch) package supplied on tape and reel for industrial-temperature operation. A microcontroller (MCU) is a single-chip computer that integrates a processor core, program memory, data memory and peripherals on one die, sitting at the lowest level of the embedded-system hierarchy: microcontroller -> embedded processor -> digital IC -> semiconductor. The AVR ATmega family is an 8-bit reduced-instruction-set (RISC) architecture executing most of its 130 instructions in a single clock cycle, delivering throughput close to 1 MIPS per MHz. Key features include the picoPower technology set for low active and sleep currents, 8KB of self-programmable Flash with read-while-write support, three flexible timer/counters (two 8-bit and one 16-bit), an 8-channel 10-bit ADC, and debugWIRE on-chip debugging using only the reset line. The V speed grade limits clocking to 10 MHz but permits the full 2.7 V to 5.5 V supply range, unlike the 20 MHz ATmega88A variants. Architecturally, the device pairs 32 general-purpose working registers directly with the ALU, avoiding accumulator bottlenecks. In-system serial programming (ICSP) over SPI allows firmware updates after board assembly, and the boot-loader-capable Flash enables field upgrades. Typical applications include battery-powered industrial sensors, HVAC and appliance control boards, and consumer or instrumentation products where 5 V operation and wide supply tolerance are required. Design consideration: keep the 10 MHz speed grade in mind when porting code written for 20 MHz ATmega88A parts; loop timing, UART baud tables and PWM frequencies scale directly with F_CPU. This page adds value beyond the datasheet by consolidating distributor pricing, drop-in same-package alternatives, and practical cross-reference guidance in one citable source.

询价 联系我们
ATMEGA88V-10MI - 8KB Flash AVR MCU 10MHz QFN-32 | Microchip
ATMEGA88V-10MI

ATMEGA88V-10MI - 8KB Flash AVR MCU 10MHz QFN-32 | Microchip

The Microchip Technology (Atmel) ATMEGA88V-10MI is a low-power 8-bit AVR RISC microcontroller with 8KB of In-System Programmable Flash, 1KB SRAM, 512B EEPROM, and 23 general-purpose I/O lines, clocked at up to 10MHz and housed in a 32-pad VQFN (5x5 mm) exposed-pad package with industrial -40C to +85C temperature range. An 8-bit microcontroller (MCU) is a single-chip computer that integrates a processor core, program memory, data memory, and peripherals such as timers, ADCs, and serial interfaces on one die. In the power-management hierarchy of embedded systems, the MCU is the master controller that supervises sensors, actuators, and communication links, making it the central component of virtually every embedded design. Key features include the AVR advanced RISC architecture with 131 mostly single-cycle instructions delivering up to 1 MIPS per MHz (10 MIPS at 10MHz), operation from 1.8V to 5.5V for battery-friendly designs, an 8-channel 10-bit ADC, a byte-oriented Two-Wire Interface (I2C-compatible), a serial USART, and SPI. DebugWIRE on-chip debugging simplifies development with only a single-pin interface. The ATmega88V uses a Harvard-architecture pipeline with 32 general-purpose working registers directly connected to the ALU, allowing two independent register accesses in one instruction cycle. Read-while-write Flash supports self-programming for bootloaders. Three flexible timer/counters (two 8-bit, one 16-bit) with compare and PWM modes drive motor control, lighting, and timing tasks. Typical applications include battery-powered sensors and metering, industrial control and automation nodes, HVAC and appliance control, and consumer electronics such as remote controls and lighting. The wide 1.8-5.5V supply range and low active/Power-Down current fit energy-constrained designs. Design consideration: place 100nF decoupling capacitors close to both VCC/GND pad pairs on the QFN exposed pad, and solder the exposed die pad to ground for thermal and signal integrity. This page adds distributor pricing tiers, same-footprint drop-in alternatives, pinout detail, and practical design notes not consolidated in the manufacturer datasheet.

询价 联系我们
ATMEGA88V-10MJ - 8-Bit AVR MCU, 8KB Flash, 1.8-5.5V | Microchip
ATMEGA88V-10MJ

ATMEGA88V-10MJ - 8-Bit AVR MCU, 8KB Flash, 1.8-5.5V | Microchip

The Microchip Technology ATMEGA88V-10MJ is an 8-bit AVR RISC microcontroller with 8KB of in-system programmable Flash memory, 1KB SRAM, 512B EEPROM, and 23 general-purpose I/O lines, operating from 1.8V to 5.5V at up to 10MHz in a 32-pin VQFN/MLF package. An 8-bit microcontroller (MCU) is a single integrated circuit that contains a processor core, memory, and programmable input/output peripherals on one chip. Within the power-management-and-control hierarchy of embedded systems, the microcontroller sits at the application layer, executing firmware that sequences sensors, actuators, and communication interfaces. The AVR architecture used in the ATmega88 family executes most of its 131 instructions in a single clock cycle, delivering throughput close to 1 MIPS per MHz. Key features of the ATMEGA88V-10MJ include self-programming Flash with read-while-write capability, an 8-channel 10-bit ADC, three flexible timer/counters with compare modes, a byte-oriented Two-Wire serial interface (I2C-compatible), a programmable serial USART, and an SPI serial port. The debugWIRE on-chip debug system allows single-wire debugging and programming, reducing pin count overhead during development. Technically, the device belongs to the picoPower AVR generation, offering multiple sleep modes including Idle, ADC Noise Reduction, Power-save, Power-down, Standby, and Extended Standby. The V suffix designates the wide 1.8V to 5.5V operating range, making the part suitable for battery-powered designs, while the 10 designates a 10MHz maximum clock at full voltage range. Typical applications include battery-powered sensor nodes, small appliance control, industrial instrumentation, LED lighting control, and motor control auxiliary functions where low-voltage operation and moderate performance are required. When designing with this MCU, remember that the 32-lead MLF package requires the exposed pad to be soldered to a grounded PCB pad for reliable operation and heat dissipation, and that debugWIRE shares the RESET pin, so fuse settings must be managed carefully. This page synthesizes verified distributor data, same-family drop-in alternatives, pinout information, and practical design notes not found in the manufacturer datasheet.

询价 联系我们
ATMEGA88V-10MU - 8KB AVR MCU, 10MHz, 1.8-5.5V | Microchip
ATMEGA88V-10MU

ATMEGA88V-10MU - 8KB AVR MCU, 10MHz, 1.8-5.5V | Microchip

The Microchip Technology ATMEGA88V-10MU (Atmel AVR ATmega series) is an 8-bit AVR RISC microcontroller featuring 8KB (4K x 16) of In-System Programmable FLASH memory, 512B EEPROM, 1KB SRAM, and 23 general-purpose I/O lines, delivered in a 32-pad VQFN (5x5 mm, MLF with exposed pad) package rated for a maximum clock speed of 10 MHz across a wide 1.8V to 5.5V supply range. An 8-bit AVR microcontroller is a Harvard-architecture RISC processor that executes most of its 131 powerful instructions in a single clock cycle, positioning the ATmega family in the embedded MCU hierarchy between tiny ATtiny parts and larger ATmega128/2560 devices. MCUs of this class integrate CPU, program memory, data memory, timers, and peripherals on a single die, replacing multi-chip solutions in cost-sensitive embedded designs. Key features include picoPower low-power technology with multiple sleep modes, read-while-write FLASH capability, three flexible timer/counters, a 10-bit ADC, and 32 general-purpose working registers tightly coupled to the ALU for high code density and C-friendly performance. Technically, the device uses the AVR enhanced RISC pipeline with single-cycle instruction execution; the wide 1.8V to 5.5V V-range (the V suffix grade) enables direct operation from two alkaline cells, a 3.3V rail, or a 5V industrial bus without a regulator change. Programming is via In-Circuit Serial Programming (ICSP) using two I/O pins plus reset, supported by MPLAB SNAP and legacy AVR ISP tools. Typical applications include battery-powered sensor nodes, home automation and IoT end nodes, industrial control panels, and consumer appliance interfaces, where the low-voltage grade and 10 MHz ceiling trade peak speed for reliable wide-supply operation. Design consideration: the V grade is limited to 10 MHz; if your system runs at 16-20 MHz or 5V with aggressive timing, select the ATMEGA88PA or ATMEGA88-20 drop-in variants in the same 32-VQFN footprint instead. This page synthesizes verified distributor specifications, same-footprint drop-in alternatives, pricing tiers, and practical design notes not found in the manufacturer datasheet.

询价 联系我们
ATMEGA88V-10MU - 8KB Flash 10MHz AVR MCU | Microchip
ATMEGA88V-10MU

ATMEGA88V-10MU - 8KB Flash 10MHz AVR MCU | Microchip

The Microchip Technology ATMEGA88V-10MU is an 8-bit AVR RISC microcontroller with 8 KB in-system programmable Flash, 512 B EEPROM, 1 KB SRAM, up to 10 MHz clock operation across a 1.8 V to 5.5 V supply range, and 23 general-purpose I/O lines, packaged in a 32-pad VQFN (5x5 mm, MLF) with exposed pad. An 8-bit microcontroller is a self-contained computing IC that integrates a processor core, program memory, data memory, and peripherals such as timers, UART, SPI, I2C, and ADC on a single chip. Within the power-management and embedded-systems hierarchy, MCUs like the ATmega88 sit at the control layer, executing firmware that drives sensors, actuators, and communication interfaces in embedded products. Key features include the AVR advanced RISC architecture with 130 powerful instructions, most executing in a single clock cycle, 32 general-purpose 8-bit working registers, and a two-cycle hardware multiplier. The picoPower technology delivers low active and sleep currents, while read-while-write Flash supports in-system self-programming for bootloaders. Peripherals include three flexible timers with PWM, an 8-channel 10-bit ADC, a programmable serial USART, SPI, and two-wire I2C interface, plus an analog comparator and on-chip debug via debugWIRE. Technically, the Harvard-architecture core fetches instructions and data over separate buses, sustaining near 1 MIPS per MHz throughput. The V variant operates at 10 MHz maximum across the full 1.8-5.5 V range, unlike the 20 MHz ATMEGA88-20 grades, enabling battery-powered designs that run directly from two alkaline cells or a single lithium cell. Typical applications include battery-powered portable instruments, industrial sensor nodes, HVAC and appliance control, and hobby or educational embedded platforms where low voltage operation and ISP Flash updatability matter. When designing, decouple both VCC pins and AVCC with 100 nF ceramics placed close to the pads, and connect the exposed pad to a solid ground plane for thermal and EMC performance. This page synthesizes distributor pricing, drop-in alternatives, pinout data, and practical design notes not found in the manufacturer datasheet.

询价 联系我们
ATMEGA88V-10MUR - 8KB AVR MCU 1.8-5.5V 10MHz VQFN-32 | Microchip
ATMEGA88V-10MUR

ATMEGA88V-10MUR - 8KB AVR MCU 1.8-5.5V 10MHz VQFN-32 | Microchip

The Microchip Technology ATMEGA88V-10MUR is a low-power 8-bit AVR RISC microcontroller with 8KB self-programming ISP flash, 1KB SRAM, and 512B EEPROM, executing up to 10 MIPS at 10 MHz in a 32-pad VQFN (5x5 mm) exposed-pad package. It operates from a single 1.8V to 5.5V supply, making it well suited to battery-powered designs. An 8-bit MCU is an integrated circuit that combines a processor core, program memory, data memory, and peripherals such as timers, ADCs, and serial interfaces on a single chip. Within the power-management and embedded hierarchy, the ATmega88 family sits in the AVR ATmega line of microcontroller units, one level below the larger ATmega328 and one level above the ATmega48. Key features include the advanced RISC AVR architecture with 131 mostly single-cycle instructions and 32 general-purpose working registers, three flexible timer/counters, a 10-bit ADC with 8 multiplexed channels, and byte-oriented two-wire (I2C-compatible), SPI, and UART/USART serial interfaces. A picoPower-class V variant supports full functionality down to 1.8V, while brown-out detection, power-on reset, PWM outputs, and a watchdog timer increase system robustness. Technically, the device uses a Harvard architecture with single-level pipelining, achieving close to one MIPS per MHz. Read-while-write flash enables self-programming for bootloaders, and debugWIRE provides on-chip debug over the reset line using tools such as the MPLAB SNAP, reducing pins required for development. Typical applications include battery-powered sensor nodes, industrial controls, consumer appliances, and lighting or motor-control subsystems where 10 MHz performance, a 10-bit ADC, and wide supply tolerance are sufficient. Design consideration: the V-variant is limited to 10 MHz; above 5.5V the maximum safe clock is derated for low-voltage operation, so verify the frequency-versus-voltage curve in the datasheet before clocking near the limit. This page synthesizes distributor pricing, drop-in alternatives such as the ATMEGA88PV-10MUR and ATMEGA328P-MU, and practical design notes not found in the manufacturer datasheet.

询价 联系我们
ATMEGA88V-10PJ - 8KB AVR MCU, 1.8V, 28-PDIP | Microchip
ATMEGA88V-10PJ

ATMEGA88V-10PJ - 8KB AVR MCU, 1.8V, 28-PDIP | Microchip

The Microchip ATMEGA88V-10PJ is a low-power 8-bit AVR RISC microcontroller with 8 KB In-System Programmable Flash, 1 KB SRAM, 512 B EEPROM, 23 general-purpose I/O lines, and a 1.8 V to 5.5 V operating supply, delivered in a 28-pin through-hole PDIP (PJ) package rated for industrial temperatures of -40C to +85C. The V suffix denotes a maximum clock frequency of 10 MHz (up to 10 MIPS at 1 MIPS per MHz). An 8-bit AVR microcontroller is a Harvard-architecture processor that executes most of its 131 instructions in a single clock cycle, positioning it within the broader hierarchy of MCU -> 8-bit microcontroller -> embedded processor. The ATmega48/88/168 family shares a common peripheral set and pinout, letting designers scale memory without PCB changes. Key features include self-programming Flash with read-while-write capability, an 8-channel 10-bit ADC, a byte-oriented Two-Wire (I2C-compatible) interface, a serial USART, SPI, three flexible timer/counters with compare modes, and debugWIRE on-chip debug. A 32-register general-purpose file is directly connected to the ALU, achieving near-single-cycle throughput. The core runs from 1.8 V, enabling battery-powered designs, while six power-saving modes including power-down at sub-uA levels extend battery life. The 28-PDIP package suits prototyping, sockets, and legacy through-hole production lines. Typical applications include industrial sensor nodes, appliance control boards, hobby and education platforms such as Arduino-compatible designs, and low-cost battery instruments. Design tip: when running below 5 V, respect the V-suffix 10 MHz frequency-voltage derating curve and enable the internal brown-out detector for supply-dip immunity. This page adds distributor sourcing context, drop-in alternatives, and design notes not found in the manufacturer datasheet. Pricing shown as of 2026-09-19.

询价 联系我们
ATMEGA88V-10PU - 8KB AVR MCU 10MHz 5V PDIP-28 | Microchip
ATMEGA88V-10PU

ATMEGA88V-10PU - 8KB AVR MCU 10MHz 5V PDIP-28 | Microchip

The Microchip (Atmel) ATMEGA88V-10PU is a picoPower 8-bit AVR RISC microcontroller featuring 8KB of In-System Programmable Flash memory, 10MHz maximum clock speed, and 1.8V to 5.5V wide supply voltage operation, housed in a 28-pin PDIP through-hole package. An 8-bit microcontroller is an integrated circuit that combines a processor core, memory, and peripherals on a single chip, executing one instruction per cycle in the AVR enhanced RISC architecture. Within the power management hierarchy of embedded systems, MCUs sit at the top level of a board's control chain: system -> MCU -> peripherals. The ATmega88 belongs to the ATmega48/88/168/328 family, sharing the same core, peripherals, and 28-pin pinout across Flash sizes. Key features include 1MIPS-per-MHz throughput from 130 powerful single-cycle instructions, 32 general-purpose working registers, and read-while-write Flash for self-programming. The device integrates 512B EEPROM, 1KB SRAM, 23 general-purpose I/O lines, three flexible timer/counters with compare modes, a byte-oriented Two-Wire (I2C) interface, an SPI serial port, a 10-bit ADC, and an internal calibrated oscillator. The picoPower technology platform minimizes active and sleep-mode currents, supporting battery-operated designs across the 1.8V-5.5V industrial-standard supply range. The Von-Neumann program/data memory space and Harvard bus architecture achieve deterministic single-cycle execution, while ISP (In-System Programming) and debugWIRE on-chip debugging simplify development without removing the chip from the board. Typical applications include industrial control panels, sensor nodes and instrumentation, hobby and educational embedded systems, and small appliances. The PDIP package makes it especially popular for prototyping, breadboarding, and low-volume through-hole production where socketing aids field replacement. Design consideration: the -10 speed grade limits the clock to 10MHz across the full 1.8V-5.5V range; at 5V, avoid exceeding this frequency, and verify brown-out detector settings when operating near 1.8V. A newer device, the ATMEGA88A, supersedes this part per Atmel/Microchip product change notices. This page synthesizes distributor pricing, drop-in alternatives within the ATmega48/88/168/328 family, and practical design notes not found in the manufacturer datasheet.

询价 联系我们
ATMEGA88V-15MT - 8-bit AVR MCU 8KB Flash 8MHz QFN-32 | Microchip
ATMEGA88V-15MT

ATMEGA88V-15MT - 8-bit AVR MCU 8KB Flash 8MHz QFN-32 | Microchip

The Microchip Technology ATMEGA88V-15MT is a picoPower 8-bit AVR RISC microcontroller with 8KB ISP flash memory, 1KB SRAM, and 512B EEPROM, operating up to 8 MHz and housed in a 32-pad QFN (5x5 mm MLF) package with exposed pad. An 8-bit AVR microcontroller is a Harvard-architecture RISC processor that executes most instructions in a single clock cycle. Within the power-management hierarchy, the ATmega88 family sits in Microchip's low-power ATmega AVR line, positioned above the ATmega48 and below the ATmega168 and ATmega328, sharing the same core, pinout, and peripheral set. Key features include read-while-write ISP flash, 23 general-purpose I/O lines, 32 general-purpose working registers, and three flexible timer/counters with compare modes. The picoPower technology delivers very low sleep-mode consumption, making the part attractive for battery-powered designs. The 15 speed-grade suffix denotes operation up to 8 MHz across the V-grade voltage range, and the MLF/QFN-32 exposed-pad package improves thermal and ground performance on compact boards. The advanced RISC architecture executes 130 powerful instructions, most in a single cycle, yielding up to 8 MIPS at 8 MHz. On-chip peripherals include a 10-bit ADC, USART, two-wire interface (I2C-compatible), SPI, and an internal calibrated RC oscillator, allowing fully self-contained single-chip designs without external crystals in many applications. Typical applications include battery-powered sensor nodes, industrial control panels, consumer appliances, and low-cost embedded controllers. The wide V-grade supply range supports both 3.3V and 5V systems. A key design consideration: this device is mature and the newer ATMEGA88A/88PA family supersedes it, so new designs should verify long-term supply or plan a footprint-compatible migration. This page synthesizes verified distributor data, drop-in alternatives, pinout, and practical design notes not found in the manufacturer datasheet.

询价 联系我们
ATMEGA8A-AN - 8-Bit AVR MCU 16MHz 8KB Flash | Microchip
ATMEGA8A-AN

ATMEGA8A-AN - 8-Bit AVR MCU 16MHz 8KB Flash | Microchip

The Microchip Technology ATMEGA8A-AN is an 8-bit AVR RISC microcontroller with 8 KB of in-system programmable Flash, 512 B EEPROM, 1 KB SRAM, 23 general-purpose I/O lines, and a 16 MHz maximum operating frequency, housed in a 32-pin TQFP (7x7 mm) package. It operates from 2.7 V to 5.5 V and delivers up to 16 MIPS throughput at 16 MHz. An 8-bit microcontroller is a single-chip computer that integrates a CPU, program memory (Flash), data memory (SRAM), non-volatile storage (EEPROM), and peripherals such as timers, serial interfaces, and analog-to-digital converters on one die. The AVR architecture is a modified Harvard RISC core that executes most instructions in a single clock cycle, giving the ATmega8A deterministic, low-latency response for real-time control. In the product hierarchy, the ATmega8A sits under 8-bit AVR microcontrollers, which belong to the broader microcontroller (MCU) family within embedded processing ICs. Key features include 8 KB Flash with read-while-write capability, 512 B EEPROM for parameter storage, 1 KB SRAM, 23 programmable I/O lines, three flexible timer/counters with compare modes, an 8-channel 10-bit ADC, a programmable USART, and both SPI and TWI (I2C) serial interfaces. The device supports in-system programming (ISP) and a boot loader, enabling field firmware updates without removing the chip. The ATmega8A is fabricated on Microchip's high-performance, low-power CMOS process and is pin-compatible with the original ATmega8, making it a direct replacement in existing designs. Its 16 MHz maximum clock at 4.5-5.5 V and 8 MHz at 2.7-4.5 V give designers a clear voltage-frequency trade-off for power-sensitive products. Typical applications include motor control boards, USBasp programmer hardware, battery chargers, sensor nodes, and legacy industrial controllers. The 32-TQFP package with 0.8 mm pitch suits automated SMT assembly, and the 23 I/O lines provide enough headroom for keypad, display, and communication interfaces in compact designs. When designing with the ATMEGA8A-AN, decouple VCC and AVCC with 100 nF ceramic capacitors placed close to the pins, and connect the AREF pin through a low-pass filter when using the ADC. Keep the reset pin pulled high through 10 kohm and provide an ISP header for programming. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet, giving engineers a single reference for selection, cross-referencing, and layout decisions.

询价 联系我们
ATMEGA8A-ANR - 8-Bit AVR MCU 16MHz 8KB Flash | Microchip (Tape & Reel)
ATMEGA8A-ANR

ATMEGA8A-ANR - 8-Bit AVR MCU 16MHz 8KB Flash | Microchip (Tape & Reel)

The Microchip Technology ATMEGA8A-ANR is an 8-bit AVR RISC microcontroller with 8 KB of in-system programmable Flash, 512 B EEPROM, 1 KB SRAM, 23 general-purpose I/O lines, and a 16 MHz maximum operating frequency, housed in a 32-pin TQFP (7x7 mm) package. It operates from 2.7 V to 5.5 V and delivers up to 16 MIPS throughput at 16 MHz. An 8-bit microcontroller is a single-chip computer that integrates a CPU, program memory (Flash), data memory (SRAM), non-volatile storage (EEPROM), and peripherals such as timers, serial interfaces, and analog-to-digital converters on one die. The AVR architecture is a modified Harvard RISC core that executes most instructions in a single clock cycle, giving the ATmega8A deterministic, low-latency response for real-time control. In the product hierarchy, the ATmega8A sits under 8-bit AVR microcontrollers, which belong to the broader microcontroller (MCU) family within embedded processing ICs. Key features include 8 KB Flash with read-while-write capability, 512 B EEPROM for parameter storage, 1 KB SRAM, 23 programmable I/O lines, three flexible timer/counters with compare modes, an 8-channel 10-bit ADC, a programmable USART, and both SPI and TWI (I2C) serial interfaces. The device supports in-system programming (ISP) and a boot loader, enabling field firmware updates without removing the chip. The ATmega8A is fabricated on Microchip's high-performance, low-power CMOS process and is pin-compatible with the original ATmega8, making it a direct replacement in existing designs. Its 16 MHz maximum clock at 4.5-5.5 V and 8 MHz at 2.7-4.5 V give designers a clear voltage-frequency trade-off for power-sensitive products. Typical applications include motor control boards, USBasp programmer hardware, battery chargers, sensor nodes, and legacy industrial controllers. The 32-TQFP package with 0.8 mm pitch suits automated SMT assembly, and the 23 I/O lines provide enough headroom for keypad, display, and communication interfaces in compact designs. When designing with the ATMEGA8A-ANR, decouple VCC and AVCC with 100 nF ceramic capacitors placed close to the pins, and connect the AREF pin through a low-pass filter when using the ADC. Keep the reset pin pulled high through 10 kohm and provide an ISP header for programming. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet, giving engineers a single reference for selection, cross-referencing, and layout decisions.

询价 联系我们
ATMEGA8A-AU - AVR 8-bit MCU 16MHz 8KB Flash TQFP-32 | Microchip
ATMEGA8A-AU

ATMEGA8A-AU - AVR 8-bit MCU 16MHz 8KB Flash TQFP-32 | Microchip

The Microchip Technology ATMEGA8A-AU is an 8-bit AVR RISC microcontroller delivering up to 16 MIPS throughput at 16 MHz, with 8 KB of In-System Self-Programmable Flash, 512 B EEPROM, 1 KB SRAM, and 23 general-purpose I/O lines, housed in a 32-pin TQFP (7x7 mm, 0.8 mm pitch) surface-mount package. An 8-bit microcontroller (MCU) is a single-chip computer that integrates a processor core, program memory, data memory, and peripherals such as timers, UART, SPI, I2C and ADC on one silicon die. Within the power management and embedded-systems hierarchy, the MCU sits at the top of the control chain, reading sensors and driving actuators; the ATmega8A belongs to the AVR family from Microchip Technology (formerly Atmel), one of the most widely deployed 8-bit MCU architectures in education and industry. Key features include the advanced AVR RISC architecture with 130 powerful instructions, most executing in a single clock cycle; a 2-cycle on-chip hardware multiplier; 10-bit ADC with up to 8 single-ended channels; and high-endurance non-volatile memory segments rated for 10,000 Flash and 100,000 EEPROM write cycles. The device runs from 4.5 V to 5.5 V at full 16 MHz speed, per the datasheet supply range for the -16 speed grade. Architecturally, the AVR core uses 32 x 8 general-purpose working registers directly connected to the ALU, achieving fully static operation and eliminating the accumulator bottleneck of classic 8051-style designs. Harvard memory architecture separates program and data buses for parallel instruction fetch. Typical applications include industrial control panels, consumer appliance interfaces, motor control, sensor nodes, and legacy Arduino-compatible boards using the MiniCore hardware package. Design consideration: at 16 MHz choose the 4.5-5.5 V supply window; for 3.3 V battery systems use the ATmega8L (8 MHz max) speed-grade variant instead. This page synthesizes distributor pricing, drop-in alternatives such as the ATmega88A family, and practical design notes not found in the manufacturer datasheet.

询价 联系我们
ATMEGA8A-AUR - AVR 8-bit MCU 16MHz 8KB Flash TQFP-32 | Microchip (Tape & Reel)
ATMEGA8A-AUR

ATMEGA8A-AUR - AVR 8-bit MCU 16MHz 8KB Flash TQFP-32 | Microchip (Tape & Reel)

The Microchip Technology ATMEGA8A-AUR is an 8-bit AVR RISC microcontroller delivering up to 16 MIPS throughput at 16 MHz, with 8 KB of In-System Self-Programmable Flash, 512 B EEPROM, 1 KB SRAM, and 23 general-purpose I/O lines, housed in a 32-pin TQFP (7x7 mm, 0.8 mm pitch) surface-mount package. An 8-bit microcontroller (MCU) is a single-chip computer that integrates a processor core, program memory, data memory, and peripherals such as timers, UART, SPI, I2C and ADC on one silicon die. Within the power management and embedded-systems hierarchy, the MCU sits at the top of the control chain, reading sensors and driving actuators; the ATmega8A belongs to the AVR family from Microchip Technology (formerly Atmel), one of the most widely deployed 8-bit MCU architectures in education and industry. Key features include the advanced AVR RISC architecture with 130 powerful instructions, most executing in a single clock cycle; a 2-cycle on-chip hardware multiplier; 10-bit ADC with up to 8 single-ended channels; and high-endurance non-volatile memory segments rated for 10,000 Flash and 100,000 EEPROM write cycles. The device runs from 4.5 V to 5.5 V at full 16 MHz speed, per the datasheet supply range for the -16 speed grade. Architecturally, the AVR core uses 32 x 8 general-purpose working registers directly connected to the ALU, achieving fully static operation and eliminating the accumulator bottleneck of classic 8051-style designs. Harvard memory architecture separates program and data buses for parallel instruction fetch. Typical applications include industrial control panels, consumer appliance interfaces, motor control, sensor nodes, and legacy Arduino-compatible boards using the MiniCore hardware package. Design consideration: at 16 MHz choose the 4.5-5.5 V supply window; for 3.3 V battery systems use the ATmega8L (8 MHz max) speed-grade variant instead. This page synthesizes distributor pricing, drop-in alternatives such as the ATmega88A family, and practical design notes not found in the manufacturer datasheet.

询价 联系我们
ATMEGA8A-MN - 8-bit AVR MCU, 16MHz, 8KB Flash | Microchip
ATMEGA8A-MN

ATMEGA8A-MN - 8-bit AVR MCU, 16MHz, 8KB Flash | Microchip

The Microchip Technology ATMEGA8A-MN is an 8-bit AVR RISC microcontroller with 8 KB of In-System Programmable (ISP) Flash, 16 MHz maximum clock speed, and 23 general-purpose I/O lines, housed in a 32-pad VQFN/MLF (5x5 mm, MN package) surface-mount footprint. A microcontroller of this class integrates a processor core, program memory, data memory, and peripherals on a single die. Within the product hierarchy, the ATmega8A belongs to the AVR ATmega family of flash-based 8-bit MCUs, which sit under the broader categories of microcontrollers, embedded processors, and semiconductors. AVR cores execute most instructions in a single clock cycle via a Harvard architecture with 32 general-purpose working registers, delivering up to 16 MIPS throughput at 16 MHz. Key features include 8 KB (4K x 16) self-programmable Flash with Read-While-Write capability, 512 bytes of EEPROM for non-volatile parameter storage, and 1 KB of internal SRAM. On-chip peripherals comprise three flexible timer/counters with compare modes, a serial programmable USART, a byte-oriented Two-Wire Interface (TWI/I2C), an SPI serial port, a 10-bit ADC with up to 8 single-ended channels, and an analog comparator. Power features include idle and power-down sleep modes plus an internal RC oscillator, allowing operation with minimal external components. The Mouser listing specifies an operating temperature range up to 105 C. Architecturally, the enhanced AVR RISC core pairs a rich instruction set with single-cycle execution, while the boot-section Flash supports self-programming through the ISP interface. In-System Programming via SPI allows firmware updates after board assembly without a socketed device. Typical applications include motor control (as demonstrated on Microchip's own ATmega8A motor-control board), industrial sensing and control nodes, consumer appliances, and hobby/embedded systems where the ATmega8A is well known as the core of early Arduino boards. Design considerations: the MN (MLF/VQFN-32) package exposes a large die-attach pad on the underside that must be soldered to a grounded copper pour for reliable grounding and heat dissipation; verify your PCB footprint supports it before substituting the TQFP ATMEGA8A-AU. This page synthesizes distributor pricing, drop-in alternatives, pinout data, and practical design notes not found in the manufacturer datasheet.

询价 联系我们
ATMEGA8A-MNR - 8KB Flash 16MHz AVR MCU | Microchip
ATMEGA8A-MNR

ATMEGA8A-MNR - 8KB Flash 16MHz AVR MCU | Microchip

The Microchip ATMEGA8A-MNR is an 8-bit AVR RISC microcontroller with 8KB of In-System Programmable Flash, 512B EEPROM, 1KB SRAM, and 23 general-purpose I/O lines, executing at up to 16 MHz and packaged in a 32-pad VQFN/MLF (5x5 mm) with exposed pad. A microcontroller is a single-chip embedded computer that integrates a processor core, program memory, data memory, and peripherals such as timers and communication interfaces. The ATmega8A belongs to the AVR ATmega family, which sits within the broader microcontroller hierarchy alongside 32-bit MCUs and application processors. AVR cores use a Harvard architecture with mostly single-cycle instruction execution, delivering roughly 1 MIPS per MHz of clock. Key features include 32 general-purpose 8-bit working registers directly connected to the ALU, three flexible timer/counters with compare modes, and read-while-write Flash that supports safe in-system bootloader updates. On-chip peripherals include a programmable serial USART, an SPI interface, and a two-wire (I2C-compatible) TWI interface, covering most common embedded connectivity needs. Technical depth: the device integrates a 10-bit ADC with up to 8 multiplexed single-ended channels in the QFN package, an internal calibrated RC oscillator (1/2/4/8 MHz) that can eliminate the external crystal in tolerant designs, an analog comparator, a watchdog timer, and power-reduction sleep modes. Programming is via SPI (ISP) or a boot-loader section in Flash, supported by mature toolchains such as Microchip Studio, avr-gcc, and the Arduino IDE-compatible cores. Typical applications include industrial sensor nodes and small automation controllers that use the 105C extended temperature rating, motor-control and appliance boards using the timer PWM outputs, and hobby/legacy embedded designs where the ubiquitous ATmega8 ecosystem simplifies firmware maintenance. Design consideration: at 5V the maximum guaranteed clock is 16 MHz, but at reduced VCC the fmax derates per the datasheet frequency-voltage curve, so verify clock speed against supply tolerance when running below 4.5V. This page synthesizes distributor pricing, drop-in alternatives, pinout data, and practical design notes not consolidated in the manufacturer datasheet. Pricing shown is as of 2026-09-19.

询价 联系我们
ATMEGA8A-MU - AVR 8-bit MCU 16MHz 8KB Flash | Microchip (Tape & Reel)
ATMEGA8A-MU

ATMEGA8A-MU - AVR 8-bit MCU 16MHz 8KB Flash | Microchip (Tape & Reel)

The Microchip Technology ATMEGA8A-MU is a high-performance, low-power 8-bit AVR RISC microcontroller delivering 16 MIPS at 16 MHz, with 8 KB ISP flash memory, 512 B EEPROM, 1 KB SRAM and 23 general purpose I/O lines, housed in a 32-pin VQFN (5x5 mm) package. A microcontroller unit (MCU) is a single-chip computer that integrates a processor core, program memory, data memory and peripherals such as timers, ADCs and serial interfaces. Within the embedded systems hierarchy, the ATmega8A belongs to the 8-bit AVR ATmega family from Atmel (now Microchip Technology), positioned below the larger ATmega88/328/64 families while covering the classic low-pin-count embedded control space. Key features include the advanced RISC architecture with 130 powerful instructions, most executing in a single clock cycle, plus 32 general-purpose working registers. The device integrates three flexible timer/counters with compare modes, a 10-bit ADC with 6 multiplexed channels, a byte-oriented two-wire interface (I2C-compatible), an SPI serial port and a programmable USART. In-system programmable (ISP) flash with read-while-write support allows firmware updates in the final product. Architecturally, the AVR core uses a Harvard structure with separate program and data buses, enabling single-cycle instruction fetch and execution. The ATMEGA8A operates from 4.5 V to 5.5 V at the full 16 MHz grade, with power-saving modes including idle and power-down to extend battery life. Internal and external interrupt sources, a watchdog timer and an on-chip debug capability via debugWIRE-style ICSP tools complete the feature set. Typical applications include industrial control and automation nodes, motor and LED control, sensor interfaces and data loggers, home appliances, HVAC systems and hobby/embedded education platforms where the 10-bit ADC and serial ports simplify analog sensing and communication. When designing with this part, note the 4.5 V to 5.5 V supply range of the 16 MHz M-grade: for 3.3 V systems, select the L-grade variant running at reduced clock, or the ATmega88PA family which supports 1.8 V operation. Decouple VCC and AVCC separately with 100 nF ceramic capacitors. This page synthesizes distributor pricing, drop-in alternatives, pinout and practical design notes not found in the manufacturer datasheet alone.

询价 联系我们