ATMEGA8A-MNR - 8KB Flash 16MHz AVR MCU | Microchip
料号： ATMEGA8A-MNR ✓ 量产中| 数量 | 单价 | 小计 |
|---|---|---|
| 1 | $2.37 | $2.37 |
| 10 | $2.25 | $22.50 |
| 100 | $2.08 | $208.00 |
| 500 | $1.92 | $960.00 |
| 1,000 | $1.78 | $1,780.00 |
ATMEGA8A-MNR 概述
A microcontroller is a single-chip embedded computer that integrates a processor core, program memory, data memory, and peripherals such as timers and communication interfaces. The ATmega8A belongs to the AVR ATmega family, which sits within the broader microcontroller hierarchy alongside 32-bit MCUs and application processors. AVR cores use a Harvard architecture with mostly single-cycle instruction execution, delivering roughly 1 MIPS per MHz of clock.
Key features include 32 general-purpose 8-bit working registers directly connected to the ALU, three flexible timer/counters with compare modes, and read-while-write Flash that supports safe in-system bootloader updates. On-chip peripherals include a programmable serial USART, an SPI interface, and a two-wire (I2C-compatible) TWI interface, covering most common embedded connectivity needs.
Technical depth: the device integrates a 10-bit ADC with up to 8 multiplexed single-ended channels in the QFN package, an internal calibrated RC oscillator (1/2/4/8 MHz) that can eliminate the external crystal in tolerant designs, an analog comparator, a watchdog timer, and power-reduction sleep modes. Programming is via SPI (ISP) or a boot-loader section in Flash, supported by mature toolchains such as Microchip Studio, avr-gcc, and the Arduino IDE-compatible cores.
Typical applications include industrial sensor nodes and small automation controllers that use the 105C extended temperature rating, motor-control and appliance boards using the timer PWM outputs, and hobby/legacy embedded designs where the ubiquitous ATmega8 ecosystem simplifies firmware maintenance.
Design consideration: at 5V the maximum guaranteed clock is 16 MHz, but at reduced VCC the fmax derates per the datasheet frequency-voltage curve, so verify clock speed against supply tolerance when running below 4.5V.
This page synthesizes distributor pricing, drop-in alternatives, pinout data, and practical design notes not consolidated in the manufacturer datasheet. Pricing shown is as of 2026-09-19.
直接替换替代料： ATMEGA8A-MNR ——相同封装，引脚兼容。需要 PCB 改动的不同封装料号已排除。
本系列中的变体
可与以下型号直接替换的同系列型号： ATMEGA8A-MNR （相同外形与封装尺寸） ——差异在于 Supply Voltage Range, Timers/Counters, Flash Memory, General Purpose I/O, Maximum Clock Frequency.
快速对比工具——选择替代料号进行并排对比：
ATMEGA8A-MN
✅ 直接替换✓ 有现货
$2.95 / 个
查看数据手册 →ATMEGA88PA-MU
✅ 直接替换✓ 有现货
$1.26 / 个
查看数据手册 →ATMEGA88A-MU
✅ 直接替换📋 参考替代料（不在目录中）
ATMEGA88-20MU
✅ 直接替换 ⚠️ 规格未核验✓ 有现货
联系询价
查看数据手册 →ATMEGA328P-MNR
✅ 直接替换📋 参考替代料（不在目录中）
ATMEGA8A-MNR 最大额定值与电气特性
| Core Processor | AVR |
| Core Size | 8-bit |
| Max Clock Frequency | 16 MHz |
| Flash Memory Size | 8 KB (4K x 16) |
| EEPROM Size | 512 B |
| SRAM Size | 1 KB (1K x 8) |
| Number of I/O | 23 |
| General Purpose Working Registers | 32 x 8-bit |
| Timers/Counters | Two 8-bit, one 16-bit with compare modes |
| Connectivity | USART, SPI, I2C (TWI) |
| ADC Resolution | 10-bit |
| ADC Channels | 8 (TQFP/QFN packages) |
| 工作温度 | -40C to +105C |
| 封装 / 外壳 | 32-VFQFN Exposed Pad (MLF), 5x5 mm |
| 安装类型 | Surface Mount |
| Packaging | Tape & Reel |
| RoHS 状态 | Compliant (Green MLF) |
ATMEGA8A-MNR 引脚配置
| 引脚 1 | PC6 (RESET) — Reset input / GPIO port C bit 6 |
| 引脚 2 | PD0 (RXD) — Port D bit 0 / USART receive |
| 引脚 3 | PD1 (TXD) — Port D bit 1 / USART transmit |
| 引脚 4 | PD2 (INT0) — Port D bit 2 / external interrupt 0 |
| 引脚 5 | PD3 (INT1) — Port D bit 3 / external interrupt 1 |
| 引脚 6 | PD4 (T0/XCK) — Port D bit 4 / timer0 clock or USART external clock |
| 引脚 7 | VCC — Digital supply voltage |
| 引脚 8 | GND — Ground |
| 引脚 9 | PB6 (XTAL1/TOSC1) — Port B bit 6 / crystal oscillator input |
| 引脚 10 | PB7 (XTAL2/TOSC2) — Port B bit 7 / crystal oscillator output |
| 引脚 11 | PD5 (T1/OC0B) — Port D bit 5 / timer1 clock or timer0 output compare B |
| 引脚 12 | PD6 (ICP1/AIN0) — Port D bit 6 / timer1 input capture or comparator positive input |
| 引脚 13 | PD7 (OC2/AIN1) — Port D bit 7 / timer2 output compare or comparator negative input |
| 引脚 14 | PB0 (ICP1/CLKO) — Port B bit 0 / timer1 input capture or clock output |
| 引脚 15 | PB1 (OC1A) — Port B bit 1 / timer1 output compare A (PWM) |
| 引脚 16 | PB2 (SS/OC1B) — Port B bit 2 / SPI slave select or timer1 output compare B |
| 引脚 17 | PB3 (MOSI/OC2) — Port B bit 3 / SPI master out or timer2 output compare |
| 引脚 18 | PB4 (MISO) — Port B bit 4 / SPI master in |
| 引脚 19 | PB5 (SCK) — Port B bit 5 / SPI clock |
| 引脚 20 | AVCC — ADC supply voltage |
| 引脚 21 | AREF — ADC reference voltage |
| 引脚 22 | GND — Ground |
| 引脚 23 | PC0 (ADC0) — Port C bit 0 / ADC channel 0 |
| 引脚 24 | PC1 (ADC1) — Port C bit 1 / ADC channel 1 |
| 引脚 25 | PC2 (ADC2) — Port C bit 2 / ADC channel 2 |
| 引脚 26 | PC3 (ADC3) — Port C bit 3 / ADC channel 3 |
| 引脚 27 | PC4 (ADC4/SDA) — Port C bit 4 / ADC channel 4 or TWI data |
| 引脚 28 | PC5 (ADC5/SCL) — Port C bit 5 / ADC channel 5 or TWI clock |
| 引脚 29 | ADC6 — ADC channel 6 (QFN/MLF packages only) |
| 引脚 30 | ADC7 — ADC channel 7 (QFN/MLF packages only) |
| 引脚 31 | VCC — Digital supply voltage (second supply pad) |
| 引脚 32 | GND — Ground (second ground pad) |
典型应用
ATMEGA8A-MNR 适用于 6 应用s: Industrial Sensor Nodes, Small Motor Control and PWM Drives, USBasp Programmers and Hobby Embedded, Home Appliance Control Panels, Battery-Powered IoT Sensor Devices, Legacy AVR Firmware Maintenance and EOL Refresh.
Industrial Sensor Nodes
The ATMEGA8A-MNR's -40C to +105C operating range and integrated 10-bit, 8-channel ADC make it well suited for industrial sensor acquisition nodes such as temperature, pressure, and level transmitters. The ADC pairs with the internal 2.56V reference option or the AREF pin for ratiometric measurement of bridge and NTC sensors, while the USART or TWI bus forwards readings to a PLC gateway. Placed near the sensor front end with the internal 1/2/4/8 MHz RC oscillator, the design eliminates crystals and BOM cost; the trade-off is RC clock accuracy of about +/-2%, so use a crystal when UART timing at high baud rates must be precise.
推荐
Small Motor Control and PWM Drives
With two 8-bit timer/counters and one 16-bit timer featuring compare and PWM modes, the ATMEGA8A-MNR generates up to three independent PWM channels for driving small DC motors, fans, and brushless ESC stages through external MOSFET drivers. The 16 MHz clock provides 8-bit PWM resolution at roughly 62.5 kHz, fast enough for quiet, filterless motor control. The 23 GPIO lines handle Hall or limit-switch inputs and status LEDs, while the input-capture-capable timer measures feedback. Keep the MCU ground return separate from motor power returns to the exposed pad to prevent PWM switching noise corrupting ADC readings - a star-ground or split-plane layout is recommended.
推荐
USBasp Programmers and Hobby Embedded
The ATMEGA8A-MNR is the standard MCU of the open-source USBasp in-circuit programmer, and its legacy ATmega8 register compatibility keeps thousands of community schematics and firmware builds directly usable. The 8KB Flash stores the USB bit-banged stack plus firmware, and read-while-write Flash allows field updates of the programmer itself. The 5x5 mm QFN suits compact dongle PCBs, and the 16 MHz crystal ties to PB6/PB7 for USB timing. Builders should note that hand-soldering the QFN exposed pad demands a hot-air station or generous via-and-paste pad design; the cut-tape ATMEGA8A-MN variant eases prototype placement.
推荐
Home Appliance Control Panels
Appliance user interfaces - oven timers, fan controllers, coffee machines - use the ATMEGA8A-MNR for its low BOM cost, 5V direct drive of LEDs and seven-segment displays, and watchdog timer for autonomous recovery from lockups. The three timer/counters multiplex display segments and debounce keys without CPU-intensive software loops, and the internal RC oscillator removes the crystal, improving vibration reliability. The 105C rating survives enclosed warm environments near heating elements. Because appliances demand long service life, budget the 8KB Flash conservatively for firmware growth; if UI complexity increases, migrate to the pin-compatible ATMEGA88PA-MU or ATMEGA328P-MNR without PCB redesign.
推荐
Battery-Powered IoT Sensor Devices
The ATMEGA8A-MNR's six power-reduction sleep modes, including power-down at microamp-level current, suit battery-powered devices such as remote sensor tags and door/window monitors. A typical duty cycle wakes the MCU via watchdog or external interrupt, samples the 10-bit ADC, transmits a short UART or TWI packet to a radio module, then re-enters power-down, yielding multi-year battery life from two AA cells. The 23 GPIOs directly bit-bang sub-GHz or 433 MHz transmitter modules. For best battery life, run from 2.7-3.0V where dynamic power scales quadratically with VCC, and verify the clock-versus-voltage derating curve in the datasheet since 16 MHz operation is not guaranteed at reduced VCC.
推荐
Legacy AVR Firmware Maintenance and EOL Refresh
Many shipping products still run ATmega8 firmware, and the ATMEGA8A-MNR is the actively manufactured refresh of the original ATmega8 die, keeping legacy designs in production without code changes. Designs originally built around ATMEGA8-16Mx MLF parts can drop in the ATMEGA8A-MNR with identical pinout, fuses, and register map, refreshing date codes and supply continuity. For supply-chain resilience, qualify the ATMEGA88PA-MU in parallel: it is footprint-identical and provides 25% more clock headroom, but requires the AVR094 migration effort. Maintain ISP programming pads (MOSI/MISO/SCK/RESET) on the PCB so field firmware updates remain possible for the product lifetime.
推荐
推荐产品汇总
工程参考数据： ATMEGA8A-MNR ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | ATMEGA8A-MN | ATMEGA88PA-MU | ATMEGA88A-MU | ATMEGA328P-MNR |
|---|---|---|---|---|---|
| Package | VQFN-32 (5x5 mm) exposed pad | VQFN-32 (5x5 mm) - same | VQFN-32 (5x5 mm) - same | VQFN-32 (5x5 mm) - same | VQFN-32 (5x5 mm) - same |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Flash Memory | 8 KB | 8 KB | 8 KB | 8 KB | 32 KB |
| SRAM | 1 KB | 1 KB | 1 KB | 1 KB | 2 KB |
| EEPROM | 512 B | 512 B | 512 B | 512 B | 1 KB |
| Max Clock Frequency | 16 MHz | 16 MHz | 20 MHz | 20 MHz | 20 MHz |
| Firmware Compatibility | Legacy ATmega8 register map | Identical (same die) | ATmega88 map - porting required (AVR094) | ATmega88 map - porting required (AVR094) | ATmega328 map - porting required |
| Operating Temperature | -40C to +105C | -40C to +105C | -40C to +105C | -40C to +85C | -40C to +85C |
关键差异点
- Zero-code-change legacy ATmega8 compatibility （对比 ATMEGA88PA-MU)
- Extended 105C temperature rating （对比 ATMEGA88A-MU)
- Lowest cost for 8KB-class designs （对比 ATMEGA328P-MNR)
- Clock headroom when migrating （对比 ATMEGA8A-MN)
设计说明
The 32-pad QFN exposes a central die pad that must be soldered to a PCB ground island for mechanical attachment and thermal dissipation; a solder-mask-defined pad with 4-5 thermal vias to the ground plane is standard practice for hand and reflow assembly. Keep the crystal within 10 mm of PB6/PB7 with short return traces, and place 100 nF decoupling capacitors at each VCC/AVCC pad within 3 mm of the pin. Extend the ISP programming pads (PB3-PB5, PC6) to test points so production programming does not require bed-of-nails access to fine-pitch pads.
ATmega8A maximum clock derates with supply voltage - the datasheet frequency-vs-VCC curve must be consulted when running below 4.5V. Estimated: at 3.3V the safe maximum is approximately 13-14 MHz per the classic AVR derating rule (roughly 1.8 MHz/V above 2.7V); running 16 MHz at 3.3V is out of specification and causes marginal timing failures that appear only over temperature. If a 3.3V design needs full speed, step down to 8 MHz via CLKPR-equivalent fuse settings or choose the picoPower ATMEGA88PA. Decouple AVCC separately with an LC or RC filter (10 ohm + 100 nF) when ADC accuracy matters.
Migrating from ATmega8 to ATmega88-family pin-compatible parts is NOT a firmware drop-in: Microchip application note AVR094 documents changed interrupt vectors, relocated timer control registers, a redesigned ADC mux, and a different EEPROM write sequence. Designs qualified on the ATmega8A should treat ATMEGA88* parts as second sources requiring full re-verification. Also note RESET on PC6 shares the ADC port - if PC6 is configured as GPIO, in-circuit ISP programming is lost unless a reset-delay/timeout fuse strategy is planned. Always verify lock-bit and BOD fuse settings before production flashing.
合规信息
FindIC lists the part as Green MLF, tape and reel, indicating RoHS-compliant, lead-free, halogen-free packaging. REACH and conflict-minerals status not stated in provided data.
