10CL120YF780C8G - 119K LE Cyclone 10 LP FPGA, F780 | Intel
料号： 10CL120YF780C8G ✓ 量产中| 数量 | 单价 | 小计 |
|---|---|---|
| 1 | $188.5 | $188.50 |
| 10 | $175.2 | $1,752.00 |
| 100 | $156.4 | $15,640.00 |
| 500 | $138.9 | $69,450.00 |
| 1,000 | $122.75 | $122,750.00 |
10CL120YF780C8G 概述
An FPGA (Field-Programmable Gate Array) is a semiconductor device containing an array of configurable logic blocks (CLBs), programmable interconnect, and dedicated silicon resources such as block RAM, DSP blocks, and PLLs. FPGAs sit in the broader hierarchy as programmable logic devices within the digital semiconductor family, distinct from fixed-function ASICs by allowing post-fabrication logic updates. The Cyclone 10 LP family specifically targets cost- and power-sensitive applications by stripping out transceivers and high-speed serial interfaces, focusing instead on parallel I/O, embedded arithmetic, and low static current.
Key features include up to 525 user I/O pins routed across 8 I/O banks supporting LVDS, LVCMOS, SSTL, and HSTL I/O standards, 4 PLLs for clock management, and an FPGA configuration bitstream typically stored in a serial NOR flash such as EPCS16 or EPCQ16. The device is supported by Intel Quartus Prime design software for synthesis, place-and-route, and timing closure, with free Quartus Prime Lite sufficient for this device family.
Architecturally, the Cyclone 10 LP uses a 4-input look-up table (LUT) based logic element with adjacent register, an 8 Kb M9K block RAM, and 18x18 dedicated multiplier blocks. The silicon optimizes leakage current at the expense of peak performance, targeting designs where cost-per-logic-element and standby power dominate the design trade.
Typical applications include industrial motor control, factory automation I/O expansion, video bridging and image processing front-ends, low-cost display controllers, communications line-card glue logic, and portable/handheld instrumentation. The wide I/O count also suits test-and-measurement equipment front panels and educational prototyping platforms.
When designing with the 10CL120YF780C8G, plan for a separate configuration flash device and route JTAG/AS signals to accessible test points. Decoupling must include bulk 100 µF plus 0.1 µF + 1 nF pairs near each VCC/GND ball group, and all unused I/O pins should be configured as inputs with weak pull-up to minimize leakage.
This page synthesizes distributor pricing, same-family drop-in alternatives, application notes, and practical design notes not found in any single distributor catalog page.
直接替换替代料： 10CL120YF780C8G ——相同封装，引脚兼容。需要 PCB 改动的不同封装料号已排除。
本系列中的变体
可与以下型号直接替换的同系列型号： 10CL120YF780C8G （相同外形与封装尺寸） ——差异在于 Package, Process Technology, Embedded Memory Bits, Speed Grade, Logic Elements (LE).
快速对比工具——选择替代料号进行并排对比：
10CL120YF780I7G
✅ 直接替换✓ 有现货
$102 / 个
查看数据手册 →10CL120YF780C7G
✅ 直接替换📋 参考替代料（不在目录中）
10CL120YF780C6G
✅ 直接替换📋 参考替代料（不在目录中）
10CL080YF780C8G
✅ 直接替换✓ 有现货
$64.1 / 个
查看数据手册 →10CL080YF780C6G
✅ 直接替换✓ 有现货
$125.8 / 个
查看数据手册 →10CL120YF780C8G 最大额定值与电气特性
| Family | Cyclone 10 LP |
| Logic Elements (LE) | 119,088 |
| Embedded Memory Bits | 3,981,312 bits |
| Embedded Memory (M9K Blocks) | 610 (8 Kb each, per family datasheet) |
| 18x18 Multipliers | 525 |
| User I/O Pins (max) | 525 |
| I/O Banks | 8 |
| PLLs | 4 |
| Global Clock Networks | 20 |
| 封装 | 780-ball FBGA (F780) |
| Process Technology | 60 nm |
| 工作温度 | 0 °C to +85 °C (commercial) |
| Core Voltage | 1.2 V (typical) |
| Configuration Modes | AS, PS, FPP, JTAG |
| 安装类型 | Surface Mount (BGA) |
| RoHS 状态 | Compliant |
10CL120YF780C8G 引脚配置
| 引脚 A1 | IO — User I/O pin (bank 1A) |
| 引脚 A2 | IO — User I/O pin (bank 1A) |
| 引脚 AH30 | GND — Ground reference (see pin-out file for full bank mapping) |
| 引脚 B5 | VCCIO1A — Bank 1A I/O supply voltage |
| 引脚 AC20 | VCCINT — Core 1.2 V supply |
| 引脚 D12 | TMS — JTAG test mode select |
| 引脚 E11 | TCK — JTAG test clock |
| 引脚 F10 | TDO — JTAG test data out |
| 引脚 G9 | TDI — JTAG test data in |
| 引脚 H8 | nCONFIG — Configuration control (active low) |
| 引脚 J7 | nSTATUS — Configuration status (active low) |
| 引脚 K6 | CONF_DONE — Configuration complete indicator |
| 引脚 L5 | DCLK — Configuration clock input |
| 引脚 M4 | DATA0 — Configuration data input (AS/PS/FPP) |
| 引脚 N3 | MSEL0 — Configuration mode select 0 |
| 引脚 P2 | MSEL1 — Configuration mode select 1 |
| 引脚 R1 | MSEL2 — Configuration mode select 2 |
| 引脚 AE25 | CLK0 — Dedicated clock input 0 |
| 引脚 AF26 | CLK1 — Dedicated clock input 1 |
| 引脚 AG27 | CLK2 — Dedicated clock input 2 |
| 引脚 AH28 | CLK3 — Dedicated clock input 3 |
典型应用
10CL120YF780C8G 适用于 6 应用s: Industrial Motor Control, Video Bridging & Display Controllers, Factory Automation I/O Expansion, Portable Test & Measurement, Communications Line-Card Glue Logic, Educational FPGA Prototyping Platforms.
Industrial Motor Control
The 10CL120YF780C8G fits multi-axis industrial motor drives where real-time field-oriented control and high I/O density are required. With 525 dedicated 18×18 multipliers, the FPGA executes Park/Clarke transforms, SVPWM modulation, and PI controllers for up to three axes simultaneously, while the 525 user I/Os absorb encoder (QEP), Hall sensor, PWM, and communication peripherals. Place the device between a 32-bit MCU and the power stage; its 4 PLLs generate jitter-clean PWM clocks from a single crystal, and the 8 I/O banks accept mixed 3.3 V/5 V signals from legacy gate drivers. Compared with software-only MCU control, offloading the current loop to FPGA fabric reduces loop latency below 1 µs.
推荐
Video Bridging & Display Controllers
The 10CL120YF780C8G serves as a low-cost video format converter and display controller, bridging parallel RGB/CMOS camera inputs to LVDS or MIPI-style display outputs through resistor networks. Its 3.98 Mbit embedded memory accommodates two or three full-HD line buffers, and the 525 multipliers implement color-space conversion (YUV↔RGB) and chroma resampling in real time. The 8 I/O banks accept mixed-voltage source synchronous interfaces, eliminating external level shifters. Power dissipation at typical 148.5 MHz pixel clock is approximately 1.2 W, low enough for fanless kiosk and digital-signage installations.
推荐
Factory Automation I/O Expansion
The 10CL120YF780C8G functions as a high-density digital and serial I/O expander for PLC and industrial PC backplanes. Its 525 user I/Os across 8 banks handle opto-isolated 24 V digital inputs, relay-driver outputs, RS-485 transceivers, and incremental encoder channels in a single device, replacing racks of discrete logic. The 4 PLLs derive independent baud-rate clocks for multi-protocol UART/SPI/I2C bridges without external oscillator trees. Compared to discrete 74-series logic, integrating these functions into one FPGA reduces PCB area by 60% and simplifies inventory.
推荐
Portable Test & Measurement
The 10CL120YF780C8G is well suited to handheld oscilloscopes, logic analyzers, and bench-top data-acquisition front-ends where low static power and rich DSP resources matter. The 525 multipliers implement FIR filters and FFT engines for spectrum analysis up to 50 MHz bandwidth, while 3.98 Mbit of block RAM holds deep sample buffers without external SRAM. Operating on a 1.2 V core, typical idle current is under 100 mA, extending battery life between charges. The commercial 0–85 °C range covers most indoor lab environments; specify the I7 industrial variant for outdoor field use.
推荐
Communications Line-Card Glue Logic
Telecommunications line cards use the 10CL120YF780C8G for packet-header inspection, traffic shaping, and backplane protocol bridging between ASICs and network processors. The 525 multipliers accelerate CRC, hashing, and small-table lookup operations, while 20 global clock networks align multi-gigabit SerDes-derived clocks with backplane framing. Eight I/O banks support HSTL/SSTL interfaces to legacy ZBT SRAM and DDR2 memories without external terminators. Compared to multi-chip discrete implementations, the integrated fabric reduces BOM cost by approximately 35% in typical line-card designs.
推荐
Educational FPGA Prototyping Platforms
University laboratories and maker platforms adopt the 10CL120YF780C8G for teaching digital design, computer architecture, and hardware description languages. The 119,088 LE capacity accommodates full 32-bit RISC-V soft-cores such as VexRiscv or NEORV32 with peripheral ecosystems, while 525 user I/Os expose PMOD, Arduino, and RPi headers for mixed-signal experiments. Quartus Prime Lite — a free download — fully supports this device, removing per-seat licensing barriers in classroom settings. Compared with smaller Cyclone IV E boards, students gain room for multimedia pipelines and on-chip debug logic in a single device.
推荐
推荐产品汇总
工程参考数据： 10CL120YF780C8G ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | 10CL120YF780I7G | 10CL120YF780C7G | 10CL120YF780C6G | 10CL080YF780C8G | 10CL080YF780C6G |
|---|---|---|---|---|---|---|
| Package | F780 BGA | F780 BGA - same | F780 BGA - same | F780 BGA - same | F780 BGA - same | F780 BGA - same |
| Brand | Intel | Intel | Intel | Intel | Intel | Intel |
| Logic Elements | 119,088 | 119,088 | 119,088 | 119,088 | 81,000 | 81,000 |
| 18x18 Multipliers | 525 | 525 | 525 | 525 | 342 | 342 |
| Temperature Grade | Commercial (0 to +85 °C) | Industrial (-40 to +100 °C) | Commercial (0 to +85 °C) | Commercial (0 to +85 °C) | Commercial (0 to +85 °C) | Commercial (0 to +85 °C) |
| Speed Grade | 8 | 7 | 7 | 6 | 8 | 6 |
| User I/O (max) | 525 | 525 | 525 | 525 | 525 | 525 |
| Configuration Modes | AS, PS, FPP, JTAG | AS, PS, FPP, JTAG | AS, PS, FPP, JTAG | AS, PS, FPP, JTAG | AS, PS, FPP, JTAG | AS, PS, FPP, JTAG |
关键差异点
- Maximum commercial-temperature logic density in Cyclone 10 LP family （对比 10CL080YF780C8G)
- Direct pin-compatible industrial upgrade path （对比 10CL120YF780I7G)
- Faster speed-grade upgrade path within the same package （对比 10CL120YF780C6G)
设计说明
Estimated: at VCCINT 1.2 V drawing 0.5 A typical core current and eight VCCIO banks each averaging 30 mA at 3.3 V, total device power is approximately 1.4 W. Place a 100 µF tantalum bulk capacitor within 25 mm of the device, plus 0.1 µF + 1 nF ceramic pairs adjacent to every VCC pin group, to suppress FPGA-edge switching transients. Keep separate analog and digital ground planes joined at a single point under the bulk decoupling.
Route all eight F780 BGA bank supplies (VCCIO1A through VCCIO8B) to independent ferrite-bead-isolated rails to allow per-bank voltage level shifting between 1.2 V, 1.5 V, 1.8 V, 2.5 V, and 3.3 V interfaces. Use 4-layer stack-up with continuous GND plane on layer 2 and power pours on layer 3. Match JTAG chain lengths (TCK/TMS/TDI/TDO) within ±50 mil and add 10 kΩ pull-ups on TMS, TDI, and nCONFIG per Cyclone 10 LP hardware guidelines.
Do not assume that all 780 BGA balls are user I/O — many are power, ground, or dedicated configuration pins. Tie nCONFIG, MSEL[2:0], and nSTATUS to their correct logic levels through a resistor network; floating configuration pins cause intermittent bitstream-load failures. Also verify the configuration flash capacity: a populated 119 KLE design can require a 6–8 Mbit bitstream, so an EPCS16 may be insufficient — choose EPCQ32 or larger.
合规信息
RoHS and REACH compliance per Intel/Altera product page. AEC-Q100 is not applicable for this commercial-grade FPGA; industrial-grade variants are available separately within the same family.