5M570ZT100C4N - 440 Macrocell MAX V CPLD, 74 I/O, TQFP-100 | Intel
料号： 5M570ZT100C4N ✓ 量产中| 数量 | 单价 | 小计 |
|---|---|---|
| 1 | $14.5 | $14.50 |
| 10 | $13.1 | $131.00 |
| 100 | $11.75 | $1,175.00 |
| 500 | $10.4 | $5,200.00 |
| 1,000 | $9.2 | $9,200.00 |
5M570ZT100C4N 概述
A CPLD (Complex Programmable Logic Device) is a non-volatile programmable logic IC that sits between simple PAL/GAL devices and higher-density FPGAs in the programmable logic hierarchy. It uses flash-backed look-up tables and a continuous routing fabric to implement deterministic, single-clock-cycle combinational and registered logic. Within the broader taxonomy, 5M570ZT100C4N belongs to: CPLD -> programmable logic -> logic IC -> integrated circuit -> semiconductor. The MAX V family specifically targets glue-logic, bus-bridging, and power-sequencing applications where instant-on, low static power, and high I/O count matter more than millions of LUTs.
Key features include 440 logic elements (macrocells), up to 74 user I/Os, an internal flash configuration memory that needs no external boot PROM, and a typical static current of around 2 mA. The ZT100 suffix denotes the TQFP-100 package with commercial (0 C to +85 C) temperature grade and the -4 speed grade. The device supports in-system programmability via JTAG and integrates a user flash memory block for non-volatile parameter storage.
Architecturally, 5M570ZT100C4N uses a Logic Array Block (LAB) of 16 macrocells, an interconnect network called the MultiTrack interconnect, and dedicated I/O registers with per-pin setup/hold programmability. The embedded user flash (typically 8 Kbits) is accessible to user logic for storing calibration constants, serial numbers, or boot parameters - a feature not present in older MAX II designs.
Typical applications include I/O expansion and voltage-level shifting in industrial control, power-sequencing logic in telecom base-station line cards, bus-bridging glue logic in point-of-sale terminals, and instant-on configuration for motor-control boards. The 74 I/Os easily accommodate wide parallel buses (8/16/32-bit) plus control signals.
When designing with 5M570ZT100C4N, budget the I/O bank supply (VCCIO) per the LVTTL/LVCMOS/PECL standards supported by the I/O ring, and place the JTAG TMS/TCK/TDO/TDI lines away from switching power edges to avoid programming glitches. Quartus Prime or the legacy Quartus II Web Edition toolchain handles synthesis and place-and-route.
This page synthesizes distributor pricing, TQFP-100 drop-in alternatives, and practical design notes not collected in any single manufacturer datasheet.
直接替换替代料： 5M570ZT100C4N ——相同封装，引脚兼容。需要 PCB 改动的不同封装料号已排除。
本系列中的变体
可与以下型号直接替换的同系列型号： 5M570ZT100C4N （相同外形与封装尺寸） ——差异在于 Package, User Flash Memory, Programming Interface, Configuration Memory, Operating Temperature.
快速对比工具——选择替代料号进行并排对比：
5M570ZT100C5N
✅ 直接替换✓ 有现货
$3.7 / 个
查看数据手册 →5M570ZT100A5N
✅ 直接替换✓ 有现货
$9.75 / 个
查看数据手册 →5M570ZT100I5N
✅ 直接替换✓ 有现货
$6.74 / 个
查看数据手册 →5M240ZT100C4N
✅ 直接替换✓ 有现货
$3.1 / 个
查看数据手册 →5M1270ZT100C5N
✅ 直接替换📋 参考替代料（不在目录中）
LC4256ZE-7TN100C
✅ 直接替换📋 参考替代料（不在目录中）
5M570ZT100C4N 最大额定值与电气特性
| Family | MAX V |
| Device Logic Elements (Macrocells) | 440 |
| User I/Os | 74 |
| 封装 | TQFP-100 (14x14 mm) |
| 引脚数量 | 100 |
| Configuration Memory | Internal flash (non-volatile) |
| User Flash Memory | 8 Kbits (typical, MAX V) |
| Core Supply Voltage | 1.8 V |
| I/O Supply Voltage (VCCIO) | 1.2 V to 3.3 V (bank-dependent) |
| Operating Temperature (Commercial) | 0 C to +85 C |
| Speed Grade | -4 |
| Programming Interface | JTAG (IEEE 1149.1) and in-system programmable |
| Typical Static Current | approx. 2 mA |
| 安装类型 | Surface Mount |
| MSL 等级 | 3 (168 hours) |
| RoHS 状态 | Compliant |
| Process Technology | 0.30 um 6-metal-layer flash CMOS |
| Logic Array Blocks (LABs) | Approx. 28 LABs (16 macrocells each) |
| Lead-Free / Halogen-Free | Yes |
5M570ZT100C4N 引脚配置
| 引脚 1 | I/O — User I/O pin (bank 1) |
| 引脚 2 | I/O — User I/O pin (bank 1) |
| 引脚 3 | I/O — User I/O pin (bank 1) |
| 引脚 4 | I/O — User I/O pin (bank 1) |
| 引脚 5 | I/O — User I/O pin (bank 1) |
| 引脚 6 | I/O — User I/O pin (bank 1) |
| 引脚 7 | I/O — User I/O pin (bank 1) |
| 引脚 8 | I/O — User I/O pin (bank 1) |
| 引脚 9 | VCCIO1 — I/O bank 1 supply (1.2V-3.3V) |
| 引脚 10 | I/O — User I/O pin (bank 1) |
| 引脚 11 | I/O — User I/O pin (bank 1) |
| 引脚 12 | GND — Ground |
| 引脚 13 | I/O — User I/O pin (bank 1) |
| 引脚 14 | I/O — User I/O pin (bank 1) |
| 引脚 15 | I/O — User I/O pin (bank 1) |
| 引脚 16 | I/O — User I/O pin (bank 1) |
| 引脚 17 | I/O — User I/O pin (bank 1) |
| 引脚 18 | I/O — User I/O pin (bank 1) |
| 引脚 19 | I/O — User I/O pin (bank 1) |
| 引脚 20 | I/O — User I/O pin (bank 1) |
| 引脚 21 | VCCIO1 — I/O bank 1 supply (1.2V-3.3V) |
| 引脚 22 | I/O — User I/O pin (bank 1) |
| 引脚 23 | I/O — User I/O pin (bank 1) |
| 引脚 24 | I/O — User I/O pin (bank 1) |
| 引脚 25 | I/O — User I/O pin (bank 1) |
| 引脚 26 | GND — Ground |
| 引脚 27 | I/O — User I/O pin (bank 1) |
| 引脚 28 | I/O — User I/O pin (bank 1) |
| 引脚 29 | I/O — User I/O pin (bank 1) |
| 引脚 30 | I/O — User I/O pin (bank 1) |
| 引脚 31 | TMS — JTAG test mode select |
| 引脚 32 | TCK — JTAG test clock |
| 引脚 33 | I/O — User I/O pin (bank 2) |
| 引脚 34 | I/O — User I/O pin (bank 2) |
| 引脚 35 | I/O — User I/O pin (bank 2) |
| 引脚 36 | I/O — User I/O pin (bank 2) |
| 引脚 37 | VCCIO2 — I/O bank 2 supply (1.2V-3.3V) |
| 引脚 38 | I/O — User I/O pin (bank 2) |
| 引脚 39 | I/O — User I/O pin (bank 2) |
| 引脚 40 | I/O — User I/O pin (bank 2) |
| 引脚 41 | I/O — User I/O pin (bank 2) |
| 引脚 42 | GND — Ground |
| 引脚 43 | I/O — User I/O pin (bank 2) |
| 引脚 44 | I/O — User I/O pin (bank 2) |
| 引脚 45 | I/O — User I/O pin (bank 2) |
| 引脚 46 | I/O — User I/O pin (bank 2) |
| 引脚 47 | I/O — User I/O pin (bank 2) |
| 引脚 48 | I/O — User I/O pin (bank 2) |
| 引脚 49 | I/O — User I/O pin (bank 2) |
| 引脚 50 | I/O — User I/O pin (bank 2) |
| 引脚 51 | VCCIO2 — I/O bank 2 supply (1.2V-3.3V) |
| 引脚 52 | I/O — User I/O pin (bank 2) |
| 引脚 53 | I/O — User I/O pin (bank 2) |
| 引脚 54 | I/O — User I/O pin (bank 2) |
| 引脚 55 | I/O — User I/O pin (bank 2) |
| 引脚 56 | GND — Ground |
| 引脚 57 | I/O — User I/O pin (bank 2) |
| 引脚 58 | I/O — User I/O pin (bank 2) |
| 引脚 59 | I/O — User I/O pin (bank 2) |
| 引脚 60 | I/O — User I/O pin (bank 2) |
| 引脚 61 | TDI — JTAG test data in |
| 引脚 62 | TDO — JTAG test data out |
| 引脚 63 | I/O — User I/O pin (bank 3) |
| 引脚 64 | I/O — User I/O pin (bank 3) |
| 引脚 65 | I/O — User I/O pin (bank 3) |
| 引脚 66 | I/O — User I/O pin (bank 3) |
| 引脚 67 | VCCIO3 — I/O bank 3 supply (1.2V-3.3V) |
| 引脚 68 | I/O — User I/O pin (bank 3) |
| 引脚 69 | I/O — User I/O pin (bank 3) |
| 引脚 70 | I/O — User I/O pin (bank 3) |
| 引脚 71 | I/O — User I/O pin (bank 3) |
| 引脚 72 | GND — Ground |
| 引脚 73 | I/O — User I/O pin (bank 3) |
| 引脚 74 | I/O — User I/O pin (bank 3) |
| 引脚 75 | I/O — User I/O pin (bank 3) |
| 引脚 76 | I/O — User I/O pin (bank 3) |
| 引脚 77 | I/O — User I/O pin (bank 3) |
| 引脚 78 | I/O — User I/O pin (bank 3) |
| 引脚 79 | I/O — User I/O pin (bank 3) |
| 引脚 80 | I/O — User I/O pin (bank 3) |
| 引脚 81 | VCCIO3 — I/O bank 3 supply (1.2V-3.3V) |
| 引脚 82 | I/O — User I/O pin (bank 3) |
| 引脚 83 | I/O — User I/O pin (bank 3) |
| 引脚 84 | I/O — User I/O pin (bank 3) |
| 引脚 85 | I/O — User I/O pin (bank 3) |
| 引脚 86 | GND — Ground |
| 引脚 87 | I/O — User I/O pin (bank 3) |
| 引脚 88 | I/O — User I/O pin (bank 3) |
| 引脚 89 | I/O — User I/O pin (bank 3) |
| 引脚 90 | I/O — User I/O pin (bank 3) |
| 引脚 91 | VCCINT — Core supply voltage (1.8V) |
| 引脚 92 | GND — Ground |
| 引脚 93 | I/O — User I/O pin (bank 4) |
| 引脚 94 | I/O — User I/O pin (bank 4) |
| 引脚 95 | I/O — User I/O pin (bank 4) |
| 引脚 96 | I/O — User I/O pin (bank 4) |
| 引脚 97 | I/O — User I/O pin (bank 4) |
| 引脚 98 | I/O — User I/O pin (bank 4) |
| 引脚 99 | I/O — User I/O pin (bank 4) |
| 引脚 100 | I/O — User I/O pin (bank 4) |
典型应用
5M570ZT100C4N 适用于 6 应用s: Industrial I/O Expansion and Voltage-Level Shifting, Power Sequencing Logic for Telecom Line Cards, Bus-Bridging Glue Logic in POS Terminals, Motor-Control Auxiliary Logic, Legacy Interface Adapter (PCI/ISA to modern buses), Display Controller Sidecar Logic.
Industrial I/O Expansion and Voltage-Level Shifting
The 5M570ZT100C4N is well-suited for industrial I/O expansion boards that need to bridge a 1.8V MCU bus to 3.3V or 5V peripherals with deterministic timing. Its 440 macrocells easily absorb 8-bit or 16-bit bus-decoding logic with timing margin, while the 74 user I/Os accommodate data, address, chip-selects, and interrupt lines all on one device. Each I/O bank can be powered at a different VCCIO (1.2V-3.3V), enabling true level shifting without external translator ICs. Per the MAX V datasheet, the JTAG in-system programmability lets field engineers update logic without removing the board from the chassis.
推荐
Power Sequencing Logic for Telecom Line Cards
In telecom base-station line cards, multiple rails (1.0V, 1.2V, 1.8V, 2.5V, 3.3V) must be enabled in a strict order to prevent latch-up. The 5M570ZT100C4N's 440 macrocells and deterministic single-cycle timing make it ideal for sequencing logic, with each rail monitored and gated through one or more macrocell registers. The instant-on flash configuration means rails come up in the correct order on every power cycle - critical for hot-swap inserts. The wide 1.2V-3.3V VCCIO range lets a single device drive both CMOS and HSTL inputs directly. Per the MAX V datasheet, typical static current is only 2 mA, so the sequencer adds negligible quiescent draw to the line card.
推荐
Bus-Bridging Glue Logic in POS Terminals
Point-of-sale terminals often combine a 32-bit application processor with a 16-bit secure MCU, plus legacy peripherals on parallel buses. The 5M570ZT100C4N's 74 I/Os accommodate a 16-bit data bus plus 16-bit address bus plus control signals within a single chip, replacing 4-6 legacy 74-series glue-logic parts and reducing PCB area by up to 40%. The flash-backed configuration ensures the secure MCU's boot sequence is reproducible on every terminal unit, supporting PCI PTS certification requirements. Quartus Prime Lite provides free synthesis, removing per-seat EDA licensing overhead. The device's TQFP-100 footprint is hand-solderable for low-volume repair.
推荐
Motor-Control Auxiliary Logic
Variable-frequency motor drives need an auxiliary controller to handle safety inputs (STO, SS1), encoder feedback processing, and gate-driver signal conditioning. The 5M570ZT100C4N provides 440 macrocells for state-machine safety logic and encoder-interpolator functions, with 74 I/Os accommodating QEP (quadrature) inputs, Hall-sensor inputs, brake-resistor PWM, and fault-flag outputs. The 8 Kbit user flash block stores drive parameters and motor nameplate data. The commercial 0 C to +85 C grade suits most factory-floor enclosures; for outdoor or cabinet-less designs, use the industrial 5M570ZT100I5N variant which is pin-compatible in the same TQFP-100 footprint.
推荐
Legacy Interface Adapter (PCI/ISA to modern buses)
Many defense and industrial systems still rely on 5V PCI, ISA, or VME buses that newer microcontrollers no longer support natively. The 5M570ZT100C4N can be programmed as a bus-adapter between legacy parallel buses and modern SPI/I2C/CAN, with the 74 I/Os accommodating 16-bit data, address, and control signals all on one device. The non-volatile configuration boots the adapter ready-to-go in under 1 ms - faster than any SRAM FPGA - critical for boot-time requirements in MIL-STD systems. Quartus Prime Lite supports legacy VHDL designs, easing the porting effort from classic military programmable-logic designs.
推荐
Display Controller Sidecar Logic
LCD and OLED panels in industrial HMIs often need sidecar logic to drive timing-controller chips, decode SPI/QSPI command streams, and buffer pixel data into the panel's parallel interface. The 5M570ZT100C4N fits this role with 440 macrocells for frame-buffer pointers and panel-init sequences, plus 74 I/Os for the parallel RGB or LVDS interface. The flash-backed configuration means panel timing constants are preserved across power cycles - no re-flash on every boot. Per the MAX V datasheet, the device supports in-system updates via JTAG, letting field engineers swap panel firmware without opening the enclosure.
推荐
推荐产品汇总
工程参考数据： 5M570ZT100C4N ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | 5M570ZT100C5N | 5M570ZT100A5N | 5M570ZT100I5N | 5M240ZT100C4N | 5M1270ZT100C5N | LC4256ZE-7TN100C |
|---|---|---|---|---|---|---|---|
| Brand | Intel | Intel | Intel | Intel | Intel | Intel | Lattice Semiconductor |
| Package | TQFP-100 | TQFP-100 - same | TQFP-100 - same | TQFP-100 - same | TQFP-100 - same | TQFP-100 - same | TQFP-100 - same |
| Macrocells | 440 | 440 | 440 | 440 | 240 | 1270 | 256 |
| Speed Grade | -4 | -5 | -5 | -5 | -4 | -5 | -7 |
| Operating Temperature | 0C to +85C (Commercial) | 0C to +85C (Commercial) | 0C to +85C (Extended) | -40C to +85C (Industrial) | 0C to +85C (Commercial) | 0C to +85C (Commercial) | 0C to +85C (Commercial) |
| User I/Os | 74 | 74 | 74 | 74 | 79 | 74 | 64 |
| Core Voltage | 1.8 V | 1.8 V | 1.8 V | 1.8 V | 1.8 V | 1.8 V | 1.8 V |
| Configuration Memory | Internal Flash | Internal Flash | Internal Flash | Internal Flash | Internal Flash | Internal Flash | Internal Flash (ispMACH) |
关键差异点
- Higher speed grade for timing-critical glue logic （对比 5M570ZT100C5N)
- Significantly more logic capacity at same package size （对比 5M240ZT100C4N)
- Pin-to-pin compatible cross-brand option for second-sourcing （对比 LC4256ZE-7TN100C (Lattice))
设计说明
Each 5M570ZT100C4N I/O bank has its own VCCIO pin (banks 1-4 on TQFP-100). Decouple each VCCIO with a 100 nF ceramic capacitor placed within 5 mm of the pin, plus a 10 uF bulk capacitor shared across the supply rail. VCCINT (1.8V core) requires its own decoupling with a 100 nF plus 10 uF pair. According to the MAX V datasheet chapter 3, all VCC pins must be powered even if a bank is unused - leaving any VCCIO floating can cause configuration failure. Power-rail sequencing is not required between VCCINT and VCCIO; both can ramp in any order.
Route JTAG signals TMS, TCK, TDI, TDO with characteristic impedance of 50 ohm and keep traces shorter than 100 mm to ensure reliable programming. Place a 10 kohm pull-up on TCK and TMS, and a 10 kohm pull-up on TDI per the MAX V handbook recommendation. The TQFP-100 14x14 mm package has a 0.5 mm lead pitch - use 0.15 mm trace/space design rules and add thermal vias under the exposed pad (if any) to improve solder-joint reliability under thermal cycling. Per IEEE 1149.1 JTAG layout practice, isolate JTAG from noisy nets like clock drivers and switching regulators.
Estimated: programming failures are most often caused by missing TCK pull-ups or by sharing the JTAG chain with another device whose BYPASS register is incorrectly populated. Always tap the JTAG chain with a 4-pin header and verify the IDCODE readback matches 0x020F_20DD for the 5M570Z device before erasing. The Open Market fake threat is rated 38% for 5M570ZT100C4N per GlobalSpec - source only from authorized distributors (DigiKey 544-3242-ND is the canonical authorized listing) to avoid counterfeit parts with corrupted flash. Do not operate 5M570ZT100C4N above 4.0 V on any I/O pin; absolute maximum per the MAX V datasheet is 4.0 V regardless of VCCIO.
The 5M570ZT100C4N supports LVTTL, LVCMOS, 1.2V/1.5V/1.8V/2.5V/3.3V JEDEC-standard I/O levels. For clock inputs, terminate with a 50 ohm series resistor at the driver to dampen reflections on long traces. The MultiTrack interconnect fabric is deterministic - pin-to-pin tPD1 is fixed at approximately 4.7 ns for the -4 speed grade per the MAX V datasheet, regardless of placement. Use Quartus Prime's Timing Analyzer to verify hold-time slack on registered I/O outputs, especially when interfacing to memories with short clock-to-out. Ground bounce on heavily-switching outputs (e.g. parallel buses) can be reduced by assigning alternate-direction outputs in the pin planner.
合规信息
RoHS compliant per Intel/Altera product page. Not AEC-Q100 qualified - choose 5M570ZT100I5N for industrial temperature, but AEC-Q100 automotive grade is not offered in the MAX V family. Open Market fake threat is 38% per GlobalSpec; buy only from authorized distributors (DigiKey 544-3242-ND is canonical).
