5M80ZT100C4N - MAX V 80 LE CPLD 7.5ns 64MC TQFP-100 | Intel
料号： 5M80ZT100C4N ✓ 量产中| 数量 | 单价 | 小计 |
|---|---|---|
| 1 | $8.5 | $8.50 |
| 10 | $7.65 | $76.50 |
| 100 | $6.8 | $680.00 |
| 500 | $6.1 | $3,050.00 |
| 1,000 | $5.45 | $5,450.00 |
5M80ZT100C4N 概述
A CPLD (Complex Programmable Logic Device) is a non-volatile programmable logic device that sits hierarchically between simple SPLDs (Simple PLDs like PAL/GAL) and large FPGAs (Field Programmable Gate Arrays). CPLDs offer instant-on configuration from on-chip flash, deterministic timing with predictable pin-to-pin delays, and high fan-in macrocell architecture - making them ideal for control-plane logic, address decoding, and peripheral interfacing rather than data-path DSP. Within the power management and board-level design hierarchy, CPLDs often replace discrete 74-series logic, saving board area and BOM cost.
Key features include 80 logic elements, 64 macrocells, 4 global clocks, a built-in 8 Kbit user flash memory block, on-chip voltage regulator supporting 1.8 V/2.5 V/3.3 V I/O standards, and MultiVolt core support allowing mixed-voltage operation. The device operates from a single 1.8 V core supply with I/O banks configurable to 1.5 V, 1.8 V, 2.5 V, or 3.3 V, simplifying interfacing with legacy 5 V-tolerant buses through level shifters.
The 5M80ZT100C4N uses a non-volatile flash-based configuration cell so it behaves like an ASIC at power-up with zero configuration time, in contrast to SRAM-based FPGAs that require external boot memory. The 100-pin TQFP package exposes 79 user I/O pins and supports LVCMOS, LVTTL, PCI, and SSTL I/O standards, enabling direct connection to microprocessors, memory buses, and parallel peripherals.
Typical applications include I/O expansion and level translation in industrial controllers, address decoding in legacy 8051/ARM designs, power-sequencing logic in telecom line cards, and LED display multiplexing in signage. The instant-on flash architecture is particularly suited to safety-critical systems where FPGA boot time is unacceptable.
When designing with this device, observe the I/O bank voltage constraints - mixing 3.3 V and 1.8 V signals requires careful VCCIO planning. Use Quartus II or the Intel Quartus Prime Lite Edition for synthesis; JTAG programming via the dedicated 4-wire JTAG port enables in-system reconfiguration without external boot devices.
This page synthesizes distributor pricing, drop-in alternatives from the MAX V family, and practical design notes not found in the standalone datasheet - giving engineers a single reference for sourcing, replacement, and layout decisions.
直接替换替代料： 5M80ZT100C4N ——相同封装，引脚兼容。需要 PCB 改动的不同封装料号已排除。
本系列中的变体
可与以下型号直接替换的同系列型号： 5M80ZT100C4N （相同外形与封装尺寸） ——差异在于 Package, Configuration Memory, MSL Level, Programming Interface, User Flash Memory.
快速对比工具——选择替代料号进行并排对比：
5M80ZT100I5N
✅ 直接替换 ⚠️ 规格未核验✓ 有现货
$7.3749 / 个
查看数据手册 →5M80ZT100A5N
✅ 直接替换 ⚠️ 规格未核验✓ 有现货
$1.85 / 个
查看数据手册 →5M80ZT100C5N
✅ 直接替换 ⚠️ 规格未核验✓ 有现货
$4.1 / 个
查看数据手册 →5M160ZT100C4N
✅ 直接替换 ⚠️ 规格未核验✓ 有现货
$4.95 / 个
查看数据手册 →5M240ZT100C4N
✅ 直接替换 ⚠️ 规格未核验✓ 有现货
$3.1 / 个
查看数据手册 →5M570ZT100C4N
✅ 直接替换 ⚠️ 规格未核验✓ 有现货
$9.2 / 个
查看数据手册 →5M80ZT100C4N 最大额定值与电气特性
| Family | MAX V |
| Logic Elements (LEs) | 80 |
| Macrocells | 64 |
| Pin-to-Pin Delay (tPD) | 7.5 ns |
| Maximum User I/O Pins | 79 |
| Number of Global Clocks | 4 |
| User Flash Memory | 8 Kbit |
| Core Voltage (VCCINT) | 1.8 V |
| I/O Voltage (VCCIO) | 1.5 V / 1.8 V / 2.5 V / 3.3 V |
| 封装 | TQFP-100 (T100) |
| 安装类型 | Surface Mount |
| 工作温度 | 0C to +85C (Commercial) |
| Process Technology | 0.18 µm flash CMOS |
| Configuration Method | Non-volatile flash (instant-on) |
| Programming Interface | JTAG (IEEE 1149.1) |
| RoHS 状态 | Compliant |
5M80ZT100C4N tqfp-100 (t100) 引脚配置指南
5M80ZT100C4N（tqfp-100 (t100) 封装）的引脚配置。 该数字 IC 包含 GPIO、通信接口（UART、SPI、I2C）和电源引脚。请参阅制造商数据手册以了解复用引脚功能和配置选项。对嵌入式系统设计和 PCB 布局至关重要。
暂无详细引脚数据： 5M80ZT100C4N.
请参阅 数据手册 以查看完整引脚配置。
典型应用
5M80ZT100C4N 适用于 6 应用s: Industrial Control I/O Expansion, Address Decoding and Glue Logic, Power Sequencing and Supervisory Logic, Bus Bridging and Protocol Conversion, LED Display Multiplexing and Signage, Consumer Electronics Glue Logic.
Industrial Control I/O Expansion
The 5M80ZT100C4N's 79 user I/O pins and 80 logic elements make it well-suited for industrial PLC I/O expansion modules where multiple 24V field signals must be debounced, multiplexed, and translated to 3.3V logic. Its 7.5 ns tPD delivers deterministic response for high-speed encoder inputs, while the 1.8V core with 3.3V-tolerant I/O banks interface directly to industrial microcontrollers without external level shifters. The non-volatile flash configuration eliminates FPGA boot latency, enabling instant-on safety responses required by IEC 61131-3 industrial control standards.
推荐
Address Decoding and Glue Logic
In legacy 8051, ARM7, and PowerPC designs, the 5M80ZT100C4N replaces multiple 74-series GAL/PAL devices by consolidating address decoding, chip-select generation, and wait-state insertion into a single 100-pin TQFP. The 64 macrocells provide ample product-term capacity for complex decode trees spanning up to 16 address bits, while the 7.5 ns tPD adds minimal access-time penalty. Programmable I/O voltage banks allow direct connection to both 5V-tolerant and 3.3V memory buses, simplifying mixed-voltage board designs.
推荐
Power Sequencing and Supervisory Logic
Telecom line cards and server motherboards require precise power-rail sequencing to meet Intel VRM and AMD SVI specifications; the 5M80ZT100C4N's 80 logic elements and 4 global clocks provide ample capacity to sequence 8-12 voltage rails with programmable delays. Its instant-on flash architecture ensures supervisory logic is active before any downstream MCU boots, critical for hot-swap and N+1 redundant power designs. The 1.8V core with MultiVolt I/O allows direct interface to both legacy 3.3V supervisors and modern 1.0V POL regulators.
推荐
Bus Bridging and Protocol Conversion
The 5M80ZT100C4N bridges legacy parallel buses (ISA, PC/104, local SRAM) to modern serial interfaces (SPI, I2C, UART) in industrial upgrade modules, providing protocol translation without an expensive microprocessor subsystem. Its 7.5 ns tPD supports bus speeds up to ~66 MHz, while 79 user I/O pins accommodate wide parallel data paths plus multiple serial channels. The deterministic flash-based configuration delivers predictable bridge latency for real-time fieldbus protocols like Profibus and CANopen used in factory automation.
推荐
LED Display Multiplexing and Signage
Large LED matrix displays and dynamic signage require high-frequency row/column multiplexing with consistent timing; the 5M80ZT100C4N's 4 global clocks and 79 user I/O pins drive 8:1 to 16:1 multiplex ratios for displays up to 32x64 pixels per device. The 7.5 ns tPD supports PWM dimming frequencies above 1 MHz, enabling 16-bit grayscale without visible flicker. Commercial 0C to +85C temperature range suits indoor and semi-outdoor installations, while non-volatile configuration allows pattern updates via JTAG without external boot memory.
推荐
Consumer Electronics Glue Logic
In set-top boxes, home gateways, and printer controllers, the 5M80ZT100C4N consolidates discrete logic implementing HDMI handshake sequencing, USB port power switching, and peripheral chip-select generation. Its 1.8V core with selectable 3.3V I/O banks interface directly to HDMI controllers and USB power switches without external level translation. The instant-on flash architecture eliminates cold-start latency in always-on consumer devices, while the commercial temperature range suits indoor operating environments.
推荐
推荐产品汇总
工程参考数据： 5M80ZT100C4N ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | 5M80ZT100I5N | 5M80ZT100A5N | 5M80ZT100C5N | 5M160ZT100C4N | 5M240ZT100C4N | 5M570ZT100C4N |
|---|---|---|---|---|---|---|---|
| Brand | Intel | Intel | Intel | Intel | Intel | Intel | Intel |
| Package | TQFP-100 (T100) | TQFP-100 (T100) - same | TQFP-100 (T100) - same | TQFP-100 (T100) - same | TQFP-100 (T100) - same | TQFP-100 (T100) - same | TQFP-100 (T100) - same |
| Logic Elements (LEs) | 80 | 80 | 80 | 80 | 160 | 240 | 570 |
| Macrocells | 64 | 64 | 64 | 64 | 128 | 192 | 440 |
| Pin-to-Pin Delay (tPD) | 7.5 ns | 7.5 ns | 7.5 ns | 5.5 ns | 7.5 ns | 7.5 ns | 7.5 ns |
| Maximum User I/O | 79 | 79 | 79 | 79 | 79 | 79 | 79 |
| Core Voltage (VCCINT) | 1.8 V | 1.8 V | 1.8 V | 1.8 V | 1.8 V | 1.8 V | 1.8 V |
| Operating Temperature | 0C to +85C (Commercial) | -40C to +100C (Industrial) | -40C to +125C (Automotive) | 0C to +85C (Commercial) | 0C to +85C (Commercial) | 0C to +85C (Commercial) | 0C to +85C (Commercial) |
| Configuration Method | Non-volatile flash (instant-on) | Non-volatile flash (instant-on) | Non-volatile flash (instant-on) | Non-volatile flash (instant-on) | Non-volatile flash (instant-on) | Non-volatile flash (instant-on) | Non-volatile flash (instant-on) |
关键差异点
- Smallest MAX V density in TQFP-100 footprint （对比 5M160ZT100C4N)
- Instant-on flash configuration vs SRAM FPGA boot time （对比 5CSXFC6C6U23C8N (Cyclone V FPGA))
- Lower quiescent current than FPGA alternatives （对比 5CSEBA6U23C8N (Cyclone V SoC))
设计说明
The 5M80ZT100C4N requires a clean 1.8V VCCINT supply with a maximum tolerance of ±5%; ripple above 50 mVpp can cause JTAG programming failures and marginal tPD timing. Decouple VCCINT with one 10 µF bulk + one 0.1 µF ceramic per pin pair, placed within 5 mm of the package. Each VCCIO bank should have its own 0.1 µF + 1 µF ceramic pair to suppress simultaneous-switching-output (SSO) noise when driving multiple LVTTL outputs at once.
The 100-pin TQFP package has a 0.5 mm pitch requiring fine PCB fabrication - specify 4-mil (0.1 mm) trace width with 4-mil spacing and use ENIG surface finish for reliable assembly. Route JTAG signals (TCK, TMS, TDI, TDO) with ground guard traces to prevent crosstalk from adjacent high-frequency I/O. Place a 4.7 kΩ pull-up on TMS and TDI to keep the JTAG state machine in known state during power-up, per IEEE 1149.1 boundary-scan requirements.
Do not mix 3.3V and 1.8V signals on the same VCCIO bank - each bank supports a single voltage level; mis-wiring can permanently damage I/O cells. The non-volatile flash programming requires VCCINT to ramp monotonically within the 0.2-50 ms range; slow or oscillating power rails may trigger in-system programming failures. When migrating between 5M80/160/240/570 density variants, regenerate the Quartus POF file - same pinout but different IDCODE values will confuse older programmers.
合规信息
RoHS compliant per Intel product page. The 5M80ZT100C4N is the commercial grade; choose 5M80ZT100A5N variant for AEC-Q100 automotive qualification. Halogen-free and lead-free per Intel MAX V family specifications.
