AD518KH/+ - Single Bipolar Op Amp in TO-99-8 | Analog Devices
料号: AD518KH/+ ✗ 停产AD518KH/+ 概述
An operational amplifier is an analog integrated circuit that amplifies the difference between its inverting and non-inverting inputs. The AD518KH/+ combines one bipolar amplifier in a conventional metal-can package, making it suitable for legacy instrumentation, signal-conditioning, buffering, and educational designs where that package and pin configuration are already established.
The principal documented features are its single-amplifier architecture, bipolar input stage, eight-pin TO-99 package, and maximum offset voltage of 6000 uV. The AD518 family is also described as a low-cost, high-speed operational-amplifier family. Its heritage package supports through-hole insertion and straightforward prototyping, although modern surface-mount amplifiers are generally preferred for new compact designs.
Within the analog-signal chain hierarchy, the AD518KH/+ sits between passive sensors or source circuits and downstream measurement, conversion, or control blocks. Its task is to increase signal amplitude, preserve the intended waveform, and drive the next circuit stage with the impedance and bandwidth required by that system. Because the device is a single amplifier, systems requiring several gain stages must use additional amplifier devices or multichannel packages.
Typical uses include laboratory instrumentation, low-frequency signal conditioning, transducer interfaces, analog buffering, closed-loop amplifier configurations, and educational or legacy control boards. The TO-99-8 package is particularly useful when maintaining an existing through-hole footprint is more important than minimizing board area or adopting the latest surface-mount technology.
Designers should confirm the manufacturer pin configuration, supply-voltage limits, input common-mode range, output swing, gain-bandwidth behavior, compensation requirements, and thermal limits in the AD518 datasheet before constructing a new circuit. Check that the offset requirement suits the application and verify stability in the intended closed-loop configuration, especially with capacitive loads.
This product record combines lifecycle information, package identification, source pricing, related amplifier references, and practical selection guidance. It is intended to help engineers identify whether the legacy AD518KH/+ package matches an existing design and what must be verified before using it as a new analog-building block.
直接替换替代料: AD518KH/+ ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
AD510LH/+
✅ 直接替换联系询价
AD515AKH
✅ 直接替换📋 参考替代料(不在目录中)
AD518KH/+ 最大额定值与电气特性
| Amplifier Type | General-purpose operational amplifier |
| Number of Circuits | 1 circuit |
| Input Stage | Bipolar |
| Input Offset Voltage, Maximum | 6000 uV |
| 封装 | TO-99-8 metal can |
| 引脚数量 | 8 pins |
| 安装类型 | Through-hole |
| Family Description | Low-cost, high-speed integrated operational amplifier |
| Product Category | Instrumentation, operational amplifiers, and buffer amplifiers |
AD518KH/+ to-99-8 metal can 引脚配置指南
AD518KH/+(to-99-8 metal can 封装)的引脚配置。 该模拟元件具有输入、输出和电源引脚。请参阅制造商数据手册以了解失调调零、补偿和使能引脚配置。适用于信号调理和放大器电路。
暂无详细引脚数据: AD518KH/+.
请参阅 数据手册 以查看完整引脚配置。
典型应用
AD518KH/+ 适用于 6 应用s: Laboratory Instrumentation Signal Conditioning, Transducer Signal Amplification, Legacy Equipment Repair, Analog Buffering, Educational Analog Electronics, Analog Control Front End.
Laboratory Instrumentation Signal Conditioning
The AD518KH/+ is suitable for conditioning a sensor or laboratory source before measurement or control, using its single bipolar operational-amplifier stage and documented maximum offset of 6000 uV. Place the device in an inverting, non-inverting, or voltage-follower configuration according to the required gain and impedance. Its TO-99-8 metal-can package makes it especially useful when repairing or replicating legacy through-hole instrumentation. Before finalizing the stage, verify input common-mode range, output swing, bandwidth, slew rate, noise, and stability against the source impedance and required measurement accuracy.
推荐
Transducer Signal Amplification
The AD518KH/+ can amplify a low-level transducer signal when its input bias current, offset behavior, common-mode range, and noise meet the transducer requirements. The listed 6000 uV maximum offset provides a concrete limit that must be compared with the acceptable measurement error; it is not automatically sufficient for high-resolution sensing. The single amplifier also requires careful grounding and a defined return path to avoid converting common ground impedance into input error. Review the manufacturer pinout and electrical limits before connecting resistive bridges, thermocouple-style circuits, or other passive sensors.
推荐
Legacy Equipment Repair
The AD518KH/+ is well suited to repairing legacy analog equipment that originally used an Analog Devices AD518-series amplifier in a TO-99-8 package. Its obsolete lifecycle status makes exact footprint, pin-function, and electrical compatibility the central design checks. Compare the original schematic with the manufacturer pin description before installation, and verify offset, gain-bandwidth, slew-rate, common-mode, and supply-voltage requirements against the circuit's operating conditions. Through-hole accessibility supports inspection and rework, but incoming material condition and traceability should be specified because legacy inventory may vary.
推荐
Analog Buffering
The AD518KH/+ can buffer a source whose impedance is too high for the next stage when the selected closed-loop configuration remains stable and the source stays within the input common-mode range. Its single general-purpose bipolar amplifier makes it straightforward to use as a unity-gain follower in legacy designs. Confirm output swing, output-current capability, capacitive-load stability, and bandwidth at the intended operating frequency. Keep the input route short, connect the feedback network close to the device, and use a low-impedance ground reference to prevent the buffer from amplifying board-level disturbance.
推荐
Educational Analog Electronics
The AD518KH/+ provides a practical example of a classic bipolar general-purpose operational amplifier in an inspectable TO-99-8 through-hole package. It can support demonstrations of closed-loop gain, negative feedback, offset nulling, and basic signal conditioning where the selected operating points match the manufacturer's limits. The package is easy to socket and probe compared with many fine-pitch surface-mount amplifiers. For instructional use, compare the data-sheet curves rather than assuming ideal behavior, especially for bandwidth, slew rate, output swing, common-mode range, and noise, which are not fully characterized by the basic product listing.
推荐
Analog Control Front End
The AD518KH/+ may be used as the input amplification stage of a legacy analog control system when its supply, bandwidth, input range, and output capability match the controller. The documented 6000 uV maximum offset must be small relative to the control signal, while the selected amplifier configuration must preserve loop stability and adequate phase margin. Because this is a single amplifier rather than a dedicated instrumentation-amplifier IC, offset, bias-current, and common-mode errors may accumulate across multiple stages. Prototype the complete signal chain and verify response, saturation, startup, and noise margin before connecting it to power or motion-control hardware.
推荐
推荐产品汇总
工程参考数据: AD518KH/+ ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | AD510LH/+ | AD515AKH |
|---|---|---|---|
| Package | TO-99-8 metal can | TO-99-8 metal can | TO-99-8 metal can |
| Brand | Analog Devices | Analog Devices | Analog Devices |
| Number of Circuits | 1 circuit | 1 circuit | 1 circuit |
| Amplifier Type | General-purpose operational amplifier | General-purpose operational amplifier | General-purpose operational amplifier |
| Pin Count | 8 pins | 8 pins | 8 pins |
| Mounting Style | Through-hole | Through-hole | Through-hole |
| Family Positioning | AD518 low-cost, high-speed operational-amplifier family | AD510 family general-purpose operational amplifier | AD515 family general-purpose operational amplifier |
关键差异点
- Documented maximum input offset voltage (对比 AD510LH/+)
- Original AD518 family positioning (对比 AD515AKH)
- Legacy through-hole implementation (对比 AD510LH/+)
设计说明
Do not substitute the AD518KH/+ solely because another amplifier also uses an 8-pin TO-99 package. Confirm the physical lead orientation, pin functions, offset-null connections, supply pins, and input/output assignments against the manufacturer diagrams. Then compare supply voltage, common-mode range, output swing, gain-bandwidth product, slew rate, and compensation requirements. A matching package outline does not by itself guarantee pin-to-pin compatibility or equivalent signal behavior.
Keep the non-inverting input and feedback route physically short, especially when the source impedance is high. Place compensation and bypass components near their associated pins according to the reference configuration, and avoid routing the output beside the input. Maintain a low-impedance ground reference and use a ground plane where practical. For TO-99-8 construction, inspect lead seating and socket contacts because long through-hole connections can add parasitic inductance and introduce unstable feedback behavior.
The documented maximum input offset voltage of 6000 uV is important in precision and control systems, but it does not describe offset drift, input bias current, noise, or common-mode error. Evaluate the complete error budget rather than using the maximum offset as the only accuracy criterion. Also verify that the selected closed-loop gain remains within the amplifier's stable bandwidth and that capacitive loading at the output does not cause ringing or instability.
合规信息
The part is obsolete and no explicit RoHS, REACH, lead-free, halogen-free, or conflict-minerals declarations were identified in the available product records.