AD622ARZ - 1-1000 Gain Instrumentation Amplifier | Analog Devices
料号: AD622ARZ ✓ 量产中AD622ARZ 概述
An instrumentation amplifier is a precision analog amplifier optimized for measuring small differential signals while rejecting large common-mode voltages. The AD622ARZ integrates a complete difference-amplifier system with precision-matched resistors, reducing the component count and board area required compared with a discrete two- or three-op-amp design.
The AD622 uses one external resistor to establish gains from 2 through 1000, while unity gain requires no external gain resistor. Its specified input offset voltage is 125 µV, and its 3 dB bandwidth reaches 1 MHz. These characteristics make it suitable for industrial sensor interfaces, bridge amplifiers, and current-measurement circuits operating within its ±18 V supply capability.
The device follows the traditional eight-pin instrumentation-amplifier pin configuration. Gain-setting resistors connect between the gain resistor pins, differential inputs enter the input pins, and the reference input supports output-voltage shifting. This architecture permits calibration and gain selection while maintaining a compact surface-mount implementation.
Typical applications include pressure and temperature transducer amplification, strain-gage bridge measurement, biomedical instrumentation, current sensing, and general differential signal conditioning. The 1 MHz bandwidth accommodates many industrial and instrumentation signals, while engineers should verify input common-mode range, output swing, supply limits, and gain accuracy against the application operating conditions.
For reliable layout, keep the gain resistor close to the device and provide solid grounding around the differential input path. Reference-pin capacitance can affect output stability, so the compensation method specified in the Analog Devices datasheet should be followed when a driven reference or nonzero reference voltage is required.
This product page combines the AD622ARZ gain, bandwidth, offset-voltage, package, and application details with drop-in candidates and practical guidance for evaluating instrumentation-amplifier replacements in existing eight-pin SOIC layouts.
直接替换替代料: AD622ARZ ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
本系列中的变体
可与以下型号直接替换的同系列型号: AD622ARZ (相同外形与封装尺寸) ——差异在于 Package, Input Type, Pin Count, Product Type.
AD627ARZ
✅ 直接替换📋 参考替代料(不在目录中)
AD628ARZ
✅ 直接替换 ⚠️ 规格未核验📋 参考替代料(不在目录中)
AD622ARZ 最大额定值与电气特性
| Product Type | Single-channel instrumentation amplifier |
| Number of Channels | 1 channel |
| Gain Range | 1 to 1000 |
| External-Resistor Gain Range | 2 to 1000 |
| 3 dB Bandwidth | 1 MHz |
| Input Offset Voltage | 125 µV |
| 电源电压 | ±18 V |
| Total Supply Voltage | 36 V |
| 输出类型 | Single-ended |
| Input Type | Differential |
| Gain Configuration | One external gain resistor for gains of 2 to 1000; no external resistor for gain 1 |
| 封装 | 8-SOIC |
| 引脚数量 | 8 pins |
| 安装类型 | Surface mount |
| Reference Input | Supported for output-voltage shifting |
| RoHS 状态 | Unknown |
| REACH Status | Unknown |
AD622ARZ 引脚配置
| 引脚 1 | RG — Gain-setting resistor connection |
| 引脚 2 | -IN — Inverting differential input |
| 引脚 3 | +IN — Noninverting differential input |
| 引脚 4 | V- — Negative supply connection |
| 引脚 5 | REF — Reference input for output-voltage shifting |
| 引脚 6 | OUT — Single-ended amplifier output |
| 引脚 7 | V+ — Positive supply connection |
| 引脚 8 | RG — Gain-setting resistor connection |
典型应用
AD622ARZ 适用于 6 应用s: Strain-Gage Bridge Measurement, Pressure Transducer Interface, Temperature Sensor Amplification, Medical and Bio-Signal Conditioning, Current-Shunt Measurement, Industrial Differential Signal Conditioning.
Strain-Gage Bridge Measurement
The AD622ARZ fits strain-gage bridge front ends because it amplifies the small differential bridge output while rejecting common-mode excitation voltage. Its gain can be set from 2 through 1000 with one external resistor, and the specified 125 µV input offset establishes a useful baseline for bridge measurement uncertainty. The 1 MHz bandwidth provides ample response for many static and moderately dynamic mechanical tests. Connect the bridge output differentially, keep the input traces short and paired, and verify that the bridge excitation and signal amplitudes remain within the amplifier's common-mode and output-swing limits.
推荐
Pressure Transducer Interface
The AD622ARZ is appropriate for resistive pressure and force transducers that produce a small differential signal over a substantial common-mode voltage. A selectable gain of up to 1000 improves use of the converter's input range, while the 125 µV offset must be included in the accuracy budget for low-pressure measurements. The 1 MHz bandwidth is more than adequate for many pressure-control loops and data-acquisition channels. Place the transducer interface close to the sensing element, maintain a grounded reference, and check supply headroom so the output does not clip.
推荐
Temperature Sensor Amplification
The AD622ARZ can condition low-level outputs from resistance-based temperature sensors, thermistors, and RTD arrangements when differential excitation and sensing are used. Its 1-to-1000 gain range allows the design to compensate for different sensor sensitivities without changing the instrumentation-amplifier footprint. The 125 µV input offset should be compared with the expected millivolt-level signal, while the 1 MHz bandwidth leaves margin for electrical noise filtering ahead of an ADC. Use the reference input only with the compensation network specified in the Analog Devices datasheet.
推荐
Medical and Bio-Signal Conditioning
The AD622ARZ can serve as a front-end amplifier for small differential bio-signal measurements when the design remains within the device's stated accuracy, bandwidth, and supply limits. Its differential inputs help reject common-mode interference, and gains from 1 to 1000 provide flexibility for millivolt-level sensor outputs. The specified 125 µV offset and 1 MHz bandwidth must be evaluated against the required signal bandwidth and safety margins. Maintain short protected input routes, use appropriate grounding and isolation methods, and avoid presenting the device as a complete medical safety solution.
推荐
Current-Shunt Measurement
The AD622ARZ is suitable for measuring the small differential voltage generated by a current shunt when common-mode voltage must be rejected. The 1-to-1000 gain range allows substantial amplification before conversion or comparison, and the 125 µV offset is an important error term when the shunt voltage is small. Its 1 MHz bandwidth supports measurement bandwidth above many static power-system applications. Keep the shunt and amplifier on the same ground reference, minimize trace area around the Kelvin sense connections, and verify output swing at the maximum expected current.
推荐
Industrial Differential Signal Conditioning
The AD622ARZ supports industrial measurement systems that combine a differential sensor with a single-ended analog input. Its complete difference-amplifier architecture reduces the need for several discrete precision op amps, while the 8-SOIC package simplifies board assembly. The 1 MHz bandwidth is appropriate for many process-control and diagnostic signals, and the gain network can be changed during calibration. Designers should verify input common-mode range, output saturation, supply sequencing, and reference-pin stability. For slower signals, adding deliberate filtering can reduce broadband noise without using the amplifier's full bandwidth.
推荐
推荐产品汇总
工程参考数据: AD622ARZ ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | AD627ARZ | AD628ARZ | AD694AR |
|---|---|---|---|---|
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Package | 8-SOIC | 8-SOIC | 8-SOIC | 8-SOIC |
| Product Type | Single-channel instrumentation amplifier | Single-channel instrumentation amplifier | Single-channel instrumentation amplifier | Single-channel instrumentation amplifier |
关键差异点
- Higher bandwidth than the AD627ARZ candidate (对比 AD627ARZ)
- Simple resistor-programmed gain range (对比 AD627ARZ)
- Single-ended output in the traditional eight-pin footprint (对比 AD694AR)
设计说明
Route the two differential inputs as a compact, symmetric pair and connect the external gain resistor directly between pins 1 and 8. Minimize copper area around the input and gain nodes because parasitic capacitance can alter bandwidth and stability. Keep the analog ground return continuous and place the input connector or sensor interface so that shared supply currents do not flow through the sensitive input ground path.
Treat the REF pin as a sensitive analog node. When the reference input is driven, biased, or connected to a resistive network, use the compensation arrangement specified in the Analog Devices datasheet. Incorrect reference compensation can cause oscillation or an unexpected frequency response. In addition, verify that signal and output excursions remain inside the common-mode and output-swing limits across temperature and supply tolerance.
A replacement in the same 8-SOIC footprint is not automatically an electrical substitute. Before using AD627ARZ, AD628ARZ, or AD694AR, compare the gain equation and required resistor value, bandwidth, offset voltage, input bias current, common-mode range, output swing, reference behavior, and supply limits. Also confirm that the required order code retains the intended temperature grade and packing method.
合规信息
The manufacturer product page and datasheet identify the AD622ARZ as an industrial instrumentation amplifier, but the available product information does not explicitly state its RoHS, REACH, lead-free, halogen-free, or conflict-minerals status.