AD8001ANZ - 800 MHz Current Feedback Amplifier | Analog Devices
料号: AD8001ANZ ✓ 量产中AD8001ANZ 概述
An operational amplifier is an active analog component that uses high open-loop gain and negative feedback to amplify small input signals with predictable closed-loop behavior. The AD8001 belongs to the current-feedback amplifier, high-speed amplifier, analog IC, and signal-conditioning IC hierarchy. Current-feedback amplifiers are frequently selected for video, instrumentation, communications, and pulse-processing circuits because their bandwidth can remain high as closed-loop gain is reduced, provided the feedback network is implemented with the correct impedance.
Key electrical features include 0.1 dB gain flatness to 100 MHz, low 50 mW power consumption, and a typical operating current listed by distributor data as approximately 70 mA. The device supports the industrial temperature range from -40 C to +85 C and is available in a PDIP-8 package. An evaluation board, AD8001-EB, is available from Analog Devices for evaluating the amplifier and reviewing its recommended schematic and layout.
The AD8001 is intended for applications requiring high-speed signal amplification rather than precision dc amplification. Its current-feedback architecture and transimpedance linearization circuitry can provide low differential gain and phase error in video chains, while its low power consumption suits portable and space-constrained equipment. Supply voltage selection is important because the amplifier is designed for low-voltage operation rather than the higher rails used by many general-purpose amplifiers.
Typical uses include video routing and distribution, high-speed instrumentation, communications interfaces, active filtering, and pulse-signal conditioning. The small PDIP-8 package is convenient for prototyping and through-hole laboratory boards, but a surface-mount option should be considered for compact production equipment when thermal performance and assembly density are priorities.
When laying out the circuit, keep the feedback resistor and inverting input connection short, use a low-inductivity ground return, and place decoupling capacitors close to the supply pins. Current-feedback amplifiers require careful feedback-impedance selection; use the application information in the manufacturer datasheet to determine the appropriate value and confirm stability and distortion in the intended gain configuration.
直接替换替代料: AD8001ANZ ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
本系列中的变体
可与以下型号直接替换的同系列型号: AD8001ANZ (相同外形与封装尺寸) ——差异在于 Package.
AD8001AN
✅ 直接替换📋 参考替代料(不在目录中)
AD8001ANZ 最大额定值与电气特性
| Amplifier Type | Current Feedback Amplifier |
| Number of Channels | 1 channel |
| Bandwidth | 800 MHz |
| Slew Rate | 1200 V/us |
| Gain Flatness | 0.1 dB to 100 MHz |
| Power Consumption | 50 mW |
| Dual Supply Voltage Range | Up to +/-6 V |
| Single Supply Voltage Range | 6 V to 12 V |
| Nominal Operating Supply | +/-5 V |
| 工作温度范围 | -40 C to +85 C |
| Input Bias Current | 6 uA |
| Input Offset Voltage | 5.5 mV |
| 封装 | 8-pin PDIP, 0.300 inch wide |
| 安装类型 | Through-hole |
| Evaluation Board | AD8001-EB |
| RoHS 状态 | Compliant |
AD8001ANZ 引脚配置
| 引脚 1 | NC — Not connected (per datasheet) |
| 引脚 2 | -INPUT — Inverting input |
| 引脚 3 | +INPUT — Non-inverting input |
| 引脚 4 | V- — Negative supply connection |
| 引脚 5 | NC — Not connected (per datasheet) |
| 引脚 6 | OUTPUT — Amplified output |
| 引脚 7 | V+ — Positive supply connection |
| 引脚 8 | NC — Not connected (per datasheet) |
典型应用
AD8001ANZ 适用于 6 应用s: High-Speed Video Signal Conditioning, Communications Receive Chains, High-Speed Instrumentation, Pulse and Edge Signal Conditioning, Active Filtering and Frequency Response Networks, Portable Test and Measurement Equipment.
High-Speed Video Signal Conditioning
The AD8001ANZ fits video conditioning stages that need wide small-signal bandwidth and fast large-signal response. Its 800 MHz bandwidth, 1200 V/us slew rate, and 0.1 dB gain flatness to 100 MHz help preserve signal integrity through routing, buffering, and gain stages. The current-feedback architecture is particularly useful when differential gain and phase behavior matter more than conventional dc precision. With dual supplies up to +/-6 V, the amplifier can be placed after a video source while maintaining headroom for the expected signal amplitude. The main design trade-off is that feedback impedance must be selected according to the gain configuration rather than copied blindly from a voltage-feedback design.
推荐
Communications Receive Chains
Use the AD8001ANZ in communications front ends where the incoming signal must be amplified before digitization or further filtering. The 800 MHz bandwidth provides margin for high-data-rate signal paths, while the 1200 V/us slew rate reduces distortion when large transitions are present. Its approximately 50 mW power consumption is useful in compact communications equipment where every milliampere contributes to thermal design. The ±6 V maximum dual-supply specification and 6 V to 12 V single-supply range allow the amplifier to be used around modern low-voltage analog rails. Layout must keep the high-speed feedback loop compact and provide a low-inductivity ground path to avoid adding noise or instability.
推荐
High-Speed Instrumentation
The AD8001ANZ is appropriate for instrumentation buffers and active analog nodes that operate well above the bandwidth of ordinary precision op amps. Its 0.1 dB gain flatness to 100 MHz and 800 MHz bandwidth are valuable when the instrument must preserve amplitude and phase relationships across a broad measurement band. The transimpedance linearization circuitry also differentiates the device from general-purpose voltage-feedback amplifiers. Designers should still evaluate input-referred noise, offset behavior, and gain accuracy for the specific measurement, since those parameters are not optimized in the same way as in a precision amplifier. A short feedback path and careful grounding are essential at these frequencies.
推荐
Pulse and Edge Signal Conditioning
The AD8001ANZ can condition fast pulses and edge-rich signals because its 1200 V/us slew rate allows large output transitions to be generated with less distortion than slower general-purpose amplifiers. The 800 MHz bandwidth supports applications where the signal spectrum extends into the hundreds of megahertz. The device is intended for low-power, low-voltage operation, so a dual ±5 V arrangement is a typical starting point when the signal swing requires symmetrical headroom. The primary design risk is ringing or instability caused by incorrect feedback impedance, excessive capacitive loading, or long PCB traces. Validate the complete gain configuration with the manufacturer evaluation board before committing to a high-volume layout.
推荐
Active Filtering and Frequency Response Networks
The AD8001ANZ is useful in active filter and frequency-response circuits where the amplifier must retain signal amplitude across a wide range of frequencies. Its gain flatness specification of 0.1 dB to 100 MHz gives a clear target for filter design, while the much higher 800 MHz bandwidth provides headroom for multi-pole networks and internal operating frequencies. The low 50 mW power consumption helps when several active stages are combined in a compact instrument. Because current-feedback amplifiers use impedance-defined feedback networks, component tolerances and parasitic capacitance can affect the response more than in a voltage-feedback implementation. Use short, symmetrical routing and verify the filter response across temperature and supply tolerance.
推荐
Portable Test and Measurement Equipment
The AD8001ANZ is a reasonable choice for portable test and measurement equipment that needs high-speed amplification without the power draw of a larger video amplifier. Its industrial temperature range of -40 C to +85 C supports industrial laboratory environments, while the PDIP-8 package simplifies through-hole prototyping and instrument construction. The 800 MHz bandwidth and 1200 V/us slew rate enable measurement of faster edges than typical precision amplifiers can reproduce. The tradeoff is that the device requires careful high-frequency layout and is not intended to replace a precision amplifier for slow dc measurements. Use the AD8001-EB evaluation board to review the reference schematic and layout before adapting the circuit to a portable instrument.
推荐
工程参考数据: AD8001ANZ ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | AD8001AN |
|---|---|---|
| Package | 8-pin PDIP | 8-pin PDIP |
| Brand | Analog Devices | Analog Devices |
| Amplifier Architecture | Current Feedback Amplifier | Current Feedback Amplifier |
| Number of Channels | 1 | 1 |
| Bandwidth | 800 MHz | 800 MHz |
| Slew Rate | 1200 V/us | 1200 V/us |
| Gain Flatness | 0.1 dB to 100 MHz | 0.1 dB to 100 MHz |
| Power Consumption | 50 mW | 50 mW |
| Supply Voltage Range | Up to +/-6 V dual or 6 V to 12 V single | Up to +/-6 V dual or 6 V to 12 V single |
| Operating Temperature Range | -40 C to +85 C | -40 C to +85 C |
关键差异点
- High-speed current-feedback performance in a PDIP package (对比 AD8001AN)
- Low power for an 800 MHz amplifier (对比 AD8001AN)
- Video-oriented gain flatness (对比 AD8001AN)
设计说明
Treat the AD8001ANZ feedback loop as a high-speed RF-style layout problem. Place the feedback resistor, inverting-input connection, and output connection on the same board region, minimize loop area, and keep the ground return short and continuous. Analog Devices specifically provides schematic and layout guidance for the AD8001-EB evaluation board; use it as the starting point for the production layout.
Decouple each supply rail directly at the device pins with low-inductance ceramic capacitance, and route the supply and ground connections away from sensitive input nodes. The AD8001 operates from up to +/-6 V dual supplies or 6 V to 12 V single supply, so verify the actual rail voltages and signal swing before selecting the bypass network. Estimated power consumption is approximately 50 mW at the nominal operating condition; confirm thermal rise in the final enclosure.
Do not assume that a current-feedback amplifier can use the same feedback resistor as a voltage-feedback amplifier. The correct feedback impedance depends on the gain setting and signal path, and incorrect values can produce ringing, overshoot, or oscillation. Check the AD8001 data sheet and AD8001-EB reference design for the selected gain configuration, then verify bandwidth and distortion on the assembled board.
合规信息
RoHS status is listed as compliant in the product comparison data. The available documentation identifies the industrial temperature range and PDIP-8 package but does not provide complete REACH, halogen-free, conflict-minerals, or AEC-Q100 information for this ordering code.