ADM241LJRZ - 120 kbps RS-232 Transceiver | Analog Devices
料号: ADM241LJRZ ✓ 量产中ADM241LJRZ 概述
An RS-232 transceiver is an interface IC that converts logic-level signals from a host or controller into RS-232 line levels and converts received RS-232 signals back into CMOS-compatible levels. It belongs to the line-driver and receiver hierarchy within the broader interface-IC and communications-IC categories. The ADM241L family uses on-board DC-DC converters to generate the bipolar voltage needed for compliant RS-232 operation from one low-voltage supply.
The ADM241LJRZ provides four transmit channels and five receive channels, allowing four RS-232 outputs and five inputs in one package. Its specified 120 kB/s data rate supports legacy serial-control, point-of-sale, industrial-control, and instrumentation links. The ±9 V output swing is particularly useful when the system does not have the ±12 V rails traditionally associated with an RS-232 interface. A shutdown function is also part of the broader ADM2xx family described by Analog Devices.
Operationally, the integrated charge-pump circuitry increases the supply voltage to produce the required positive and negative line voltages. This eliminates the need for a separate dual-polarity RS-232 supply, while the small 1 µF capacitor requirement helps reduce board area. However, charge-pump ripple and switching noise remain important considerations when the transceiver shares a sensitive analog or high-speed digital supply domain.
Typical uses include industrial control systems, test and measurement equipment, data-acquisition systems, security equipment, and embedded serial interfaces. The 28-pin SOIC footprint provides a practical upgrade path for designs that need four RS-232 driver outputs and five receiver inputs without using separate driver and receiver ICs. Care is still required for cable routing, ground reference, and protection at exposed connector interfaces.
For PCB implementation, place the charge-pump capacitors and interface bypass capacitor close to their specified pins, keep RS-232 traces away from sensitive analog inputs, and provide the connector-side transient protection required by the installation environment. Treat the RS-232 ground as a signal reference and route it with the interface conductors rather than treating it as an incidental chassis connection.
This product page combines the ADM241L specification summary, documented drop-in alternatives, application guidance, and package-level design notes to help engineers evaluate the ADM241LJRZ for new and existing RS-232 interfaces.
直接替换替代料: ADM241LJRZ ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
本系列中的变体
可与以下型号直接替换的同系列型号: ADM241LJRZ (相同外形与封装尺寸) ——差异在于 Package, Number of Receivers, Package Width, Maximum Data Rate, Number of Drivers.
HIN211CB-T
✅ 直接替换📋 参考替代料(不在目录中)
MAX211ECWI+
✅ 直接替换联系询价
查看数据手册 →HIN241IBZ
✅ 直接替换📋 参考替代料(不在目录中)
HIN241CBZ-T
✅ 直接替换📋 参考替代料(不在目录中)
HIN241IB
✅ 直接替换📋 参考替代料(不在目录中)
ADM241LJRZ 规格参数
| Product Type | RS-232 line transceiver |
| Number of Drivers | 4 |
| Number of Receivers | 5 |
| Nominal Supply Voltage | 5 V |
| Supply Voltage Range | 4.5 V to 5.5 V |
| Maximum Data Rate | 120 kB/s |
| RS-232 Output Swing | ±9 V |
| Charge-Pump Capacitor Value | 1 µF |
| Interface Standards | EIA-232-E and V.28 |
| Shutdown Feature | Low-power shutdown mode |
| 封装 | 28-pin SOIC |
| Package Width | 7.50 mm |
| 安装类型 | Surface mount |
| Logic Technology | CMOS |
ADM241LJRZ 7.50 mm 引脚配置指南
ADM241LJRZ(7.50 mm 封装)的引脚配置。 引脚编号、功能和连接图在制造商数据手册中定义。请参阅该手册以了解确切的封装尺寸和焊接指南。
暂无详细引脚数据: ADM241LJRZ.
请参阅 数据手册 以查看完整引脚配置。
典型应用
ADM241LJRZ 适用于 6 应用s: Industrial Control Systems, Point-of-Sale Terminals, Test and Measurement Equipment, Data Acquisition Systems, Security and Access Equipment, Embedded Serial Interfaces.
Industrial Control Systems
The ADM241LJRZ fits legacy industrial controllers that must communicate with several RS-232 peripherals from one 5 V supply. Four drivers support four outgoing command or control channels, while five receivers accept up to five incoming data signals at rates as high as 120 kB/s. Its integrated DC-DC converters eliminate the need for a separate ±12 V supply and produce approximately ±9 V RS-232 output swing. Because the interface is not intended to carry high-speed signals, route the RS-232 conductors away from sensitive analog nodes and place transient protection at the external connector. The low-power shutdown mode can also reduce consumption when the controller does not need active communication.
推荐
Point-of-Sale Terminals
Point-of-sale equipment often combines cash drawers, scanners, printers, and customer displays on multiple RS-232 ports. The ADM241LJRZ provides four driver outputs and five receiver inputs, allowing several of those links to share one interface IC. Operation from 4.5 V to 5.5 V suits compact systems that already distribute a regulated 5 V rail, and the 120 kB/s maximum rate exceeds the throughput normally required for transaction peripherals. The approximately ±9 V swing supports RS-232 signaling without a separate bipolar supply. In a retail enclosure, add connector-side surge protection because users may attach and disconnect external cables while the terminal is operating.
推荐
Test and Measurement Equipment
The ADM241LJRZ is suitable for laboratory instruments and automated test equipment that retain RS-232 ports for legacy instruments, service interfaces, or fixture controllers. Its four transmit and five receive channels can reduce the number of separate interface ICs required when several instruments must share a controller. The 120 kB/s rate is appropriate for command and measurement transfer, while the single 5 V supply simplifies integration with modern digital control hardware. Keep the interface's charge-pump supply return close to the device and observe the manufacturer's component-placement recommendations to prevent converter noise from coupling into precision measurement circuitry.
推荐
Data Acquisition Systems
Data-acquisition controllers can use the ADM241LJRZ to connect legacy sensors, signal conditioners, and laboratory modules over RS-232. Five receiver inputs are useful for monitoring several peripheral statuses, while four drivers can send commands to independently addressed devices. The 120 kB/s limit suits legacy telemetry and configuration traffic rather than bulk sensor streaming. Its integrated charge pump allows operation from a single 5 V rail, which helps systems where generating ±12 V would increase power and board complexity. Place the interface away from high-gain analog front ends, use a continuous ground reference with the RS-232 conductors, and protect external connectors from industrial transients.
推荐
Security and Access Equipment
Access-control and security equipment can use the ADM241LJRZ for legacy readers, controllers, alarm panels, or configuration links that implement RS-232. Four driver channels and five receiver channels support bidirectional equipment combinations without requiring one transceiver per link. The single 5 V operating range is practical for embedded systems that already use a regulated 5 V control rail, while the specified 120 kB/s data rate is appropriate for command traffic and status reporting. Secure implementations should also include the required external line protection and ensure that exposed RS-232 connectors are not used as general-purpose network interfaces without appropriate isolation and enclosure controls.
推荐
Embedded Serial Interfaces
Embedded control boards can use the ADM241LJRZ when an existing product revision includes RS-232 connectors but the available supply rail is only 5 V. Four outputs and five inputs provide enough channels for several embedded modules, and the 120 kB/s maximum is suitable for configuration, diagnostics, and firmware-command interfaces. Integrated DC-DC converters remove the need for a separate negative supply while maintaining approximately ±9 V line swing. Designers should reserve space around the 28-pin SOIC for the specified 1 µF charge-pump capacitors and follow the manufacturer's pin table so every unused receiver input is handled explicitly.
推荐
推荐产品汇总
工程参考数据: ADM241LJRZ ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | HIN211CB-T | MAX211ECWI | HIN241IBZ | HIN241CBZ-T | HIN241IB |
|---|---|---|---|---|---|---|
| Package | 28-pin SOIC | 28-pin SOIC | 28-pin SOIC | 28-pin SOIC | 28-pin SOIC | 28-pin SOIC |
| Brand | Analog Devices | HIN241 | Maxim Integrated | HIN241 | HIN241 | HIN241 |
| Number of Drivers | 4 | 4 | 4 | 4 | 4 | 4 |
| Number of Receivers | 5 | 1 | 5 | 1 | 1 | 1 |
关键差异点
- Five receiver channels in the original interface (对比 HIN211CB-T)
- Direct four-driver, five-receiver channel organization (对比 MAX211ECWI)
- Single 5 V supply with approximately ±9 V swing (对比 HIN241IBZ)
- Low-power shutdown operation (对比 HIN241CBZ-T)
设计说明
Place the charge-pump capacitors and supply bypass capacitor directly beside their associated ADM241LJRZ pins, following the Analog Devices datasheet layout. Keep these high-current switching paths compact and avoid routing them beneath sensitive analog inputs. The documented 1 µF charge-pump capacitor value should not be changed without reviewing the corresponding data sheet because stability and output-swing performance depend on the recommended network.
Route each RS-232 driver and receiver path away from clocks, precision analog inputs, and switching power-converter nodes. The 120 kB/s maximum is appropriate for legacy RS-232, but edge-rate harmonics can still couple into nearby circuitry. Maintain a continuous interface-ground reference with the cable, keep return-current paths short, and use a solid ground plane where practical.
Do not assume every 28-pin RS-232 transceiver is electrically interchangeable. HIN211CB-T and the HIN241 alternatives provide fewer receivers than the ADM241LJRZ, while MAX211ECWI uses 0.1 µF capacitors compared with the ADM241LJRZ value of 1 µF. Check every pin, capacitor value, supply range, shutdown connection, and package dimension before approving a replacement.
The integrated DC-DC converter removes the need for a ±12 V supply but does not protect the interface from external cable transients. Place suitable RS-232 line protection at the connector, with its return connection arranged to prevent surge current from flowing through sensitive board ground paths. Validate the protection threshold against the interface's absolute-maximum ratings before production release.
合规信息
The ADM241L interface IC is not an automotive-qualified power device, so AEC-Q100 is not applicable. RoHS, REACH, lead-free, halogen-free, and conflict-minerals status were not established from the available manufacturer page.