ADS7230IPW - 12-Bit 2-Channel 1MSPS SAR ADC | Texas Instruments
料号: ADS7230IPW ✓ 量产中ADS7230IPW 概述
An ADC is an analog-to-digital converter, a semiconductor that transforms continuous voltage signals into numeric codes for digital processing. A SAR ADC compares the sampled input with a capacitor-based internal DAC through successive approximation, providing predictable conversion timing and straightforward digital control. Within the hierarchy of data-converter ICs, data converters, and analog signal-processing semiconductors, the ADS7230 supports compact acquisition systems that need moderate resolution and rapid sampling.
The ADS7230's principal characteristics include 12-bit resolution, two selectable unipolar input channels, a 1 MSPS conversion rate, and a serial interface. Its 2-to-1 multiplexer allows one converter to monitor two analog sources without duplicating the conversion core. The programmable TAG bit output option identifies the selected input when the host processor receives conversion data, helping associate each sample with its signal source.
The device uses a capacitor-based SAR conversion core with inherent sample-and-hold behavior. This architecture is suitable for instrumentation, industrial monitoring, and embedded measurement systems where a low-power ADC must acquire changing analog inputs while the controller reads results through a serial connection. The ADS7230 shares its conversion core with the single-channel ADS7229, while adding the ADS7230's two-to-one input multiplexer and programmable TAG option.
Typical uses include dual-sensor monitoring, process-control data acquisition, battery-powered measurement instruments, industrial interface modules, and embedded control systems. Two analog channels can be sampled sequentially through the internal multiplexer, reducing component count when a design must observe two related unipolar signals.
When laying out the circuit, place input and reference-network components close to their associated pins, route the serial interface away from sensitive analog inputs, and provide a stable reference and supply arrangement. Confirm acquisition timing, serial-interface mode, input range, and the required external components against the manufacturer datasheet before finalizing the schematic and PCB.
直接替换替代料: ADS7230IPW ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
该产品暂无直接替换替代料。
请求替代料ADS7230IPW 最大额定值与电气特性
| 分辨率 | 12 bit |
| Conversion Rate | 1 MSPS |
| Analog Input Channels | 2 channels |
| Input Multiplexer | 2-to-1 MUX |
| Input Type | Single/dual unipolar input |
| ADC Architecture | Capacitor-based SAR with inherent sample-and-hold |
| Digital Interface | Serial interface |
| Programmable TAG Output | Supported |
| 封装 | 16-pin TSSOP |
| 安装类型 | Surface mount |
| Power Class | Low-power ADC |
ADS7230IPW 16-pin tssop 引脚配置指南
ADS7230IPW(16-pin tssop 封装)的引脚配置。 该模拟元件具有输入、输出和电源引脚。请参阅制造商数据手册以了解失调调零、补偿和使能引脚配置。适用于信号调理和放大器电路。
暂无详细引脚数据: ADS7230IPW.
请参阅 数据手册 以查看完整引脚配置。
典型应用
ADS7230IPW 适用于 6 应用s: Dual-Sensor Monitoring, Industrial Process Measurement, Battery-Powered Measurement Instruments, Embedded Control Systems, Power and Battery Monitoring, Laboratory Data Acquisition.
Dual-Sensor Monitoring
The ADS7230IPW fits dual-sensor monitoring because its 2-to-1 multiplexer can select between two unipolar analog inputs while the 12-bit SAR core converts at up to 1 MSPS. Place the converter between conditioned sensor outputs and the controller, then use the serial interface to retrieve each code. The programmable TAG option can identify the selected input, reducing software ambiguity when two measurements are acquired sequentially. Compared with using two separate ADC packages, this approach simplifies the board footprint, although channel switching means the two sources are not sampled at exactly the same instant.
推荐
Industrial Process Measurement
ADS7230IPW is suitable for industrial process measurement when two conditioned, unipolar signals must be digitized into a compact controller interface. Its 12-bit resolution provides 4096 numerical codes across the selected input range, while the 1 MSPS SAR conversion rate supports rapid sampling of slowly changing process quantities. Use the internal channel multiplexer to reduce converter count, and add suitable input protection and filtering before the ADC pins. The serial interface keeps the digital connection compact, but reference stability and analog grounding remain important to repeatable measurements.
推荐
Battery-Powered Measurement Instruments
The low-power ADS7230IPW architecture is appropriate for portable measurement instruments that sample more than one unipolar sensor signal. The 12-bit converter operates at up to 1 MSPS, allowing acquisition timing to be configured around the application's actual bandwidth rather than operating continuously at the maximum rate. Its serial interface supports integration with an embedded controller, while the multiplexer minimizes package count. Power budget calculations should include both active conversion consumption and the time the controller spends acquiring, processing, and displaying the samples.
推荐
Embedded Control Systems
ADS7230IPW works well as an analog front end for embedded control systems that monitor two external inputs and need compact serialized results. The SAR conversion process provides a defined acquisition event, and the TAG output can support deterministic channel labeling in firmware. Use the converter to digitize potentiometer positions, divider outputs, or conditioned sensor levels, then transmit the result over the serial interface. Validate the controller's timing against the manufacturer interface diagrams, especially when using hardware triggering or interrupt-driven conversion.
推荐
Power and Battery Monitoring
ADS7230IPW can digitize two scaled, unipolar power-monitoring signals in equipment where voltage and current must both be observed. Conditioning dividers or amplifiers can map each quantity into the converter's supported input range, after which the 2-to-1 multiplexer samples the channels sequentially. The 12-bit resolution and 1 MSPS capability provide more conversion timing headroom than many low-rate monitoring loops require. Carefully separate the analog input routing from switching-current paths and use the manufacturer reference arrangement for supply and reference stability.
推荐
Laboratory Data Acquisition
ADS7230IPW supports compact laboratory acquisition modules that need two unipolar inputs, 12-bit numeric resolution, and a serial data path. The 1 MSPS SAR conversion rate is suitable for many sensor, potentiometer, and slow waveform measurement tasks, and the programmable TAG bit helps the acquisition software identify each converted channel. Place input conditioning close to the device, keep the serial traces away from sensitive analog nodes, and account for channel-switching time in the sample schedule. The manufacturer datasheet should define the supported serial modes and trigger behavior used by the instrument firmware.
推荐
推荐产品汇总
工程参考数据: ADS7230IPW ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 |
|---|---|
| Package | 16-pin TSSOP |
| Brand | Texas Instruments |
| Resolution | 12 bit |
| Conversion Rate | 1 MSPS |
| Analog Input Channels | 2 channels |
| Input Multiplexer | 2-to-1 MUX |
| ADC Architecture | Capacitor-based SAR with inherent sample-and-hold |
| Digital Interface | Serial interface |
| Programmable TAG Output | Supported |
| Input Type | Single/dual unipolar input |
关键差异点
- Dual-channel acquisition in one ADC (对比 ADS7229)
- Programmable source identification (对比 ADS7229)
- Shared high-speed SAR conversion core (对比 ADS7229)
设计说明
Route each analog input directly to its ADC pin through a compact conditioning network, and keep the serial-interface traces away from those input nodes. Place the reference and supply bypass components close to their associated pins, with short ground returns and a quiet analog ground region. Because the ADS7230 multiplexes two channels, asymmetric trace lengths and input leakage can create channel-dependent offsets; use matched layouts where measurements must agree closely.
Treat both analog inputs as potentially high-impedance nodes until the complete input-network impedance is known. Keep leakage paths away from the input pins, verify settling after multiplexer selection, and apply an appropriate acquisition time for the source impedance. If the signals carry substantial high-frequency content, place the anti-alias filter close to the converter so switching transients and controller activity do not fold into the measured bandwidth.
Do not assume that a shared SAR core makes different ADS72xx devices pin-compatible. The ADS7229 is single-channel, while ADS7230IPW includes a 2-to-1 multiplexer and TAG function, so verify every terminal, supply sequence, reference connection, and serial timing signal against the exact manufacturer datasheet. Also confirm the operating input range before scaling sensor outputs; the channel multiplexing alone does not allow arbitrary bipolar or negative signals to be connected directly.
合规信息
Compliance status was not stated on the identified manufacturer and distributor pages. Confirm current declarations for the exact ADS7230IPW ordering code and manufacturing site.