ADS7845E - 12-Bit 5-Wire Touch Controller | Texas Instruments
料号: ADS7845E ✓ 量产中ADS7845E 概述
A 5-wire resistive touch-screen controller is an analog interface integrated circuit that measures X and Y coordinates by applying controlled voltages through the transparent resistive layers of a touch panel. The measured voltage represents position relative to the panel edges, so the controller converts the analog result into a digital value for a host processor. The ADS7845E occupies the touchscreen-controller branch of the ADC and interface hierarchy, combining a sampling ADC, low-on-resistance switches, reference control, and serial communication in one device.
The controller provides 12-bit resolution, ratiometric conversion, and a maximum conversion rate of 125 kHz. Its low-power design supports portable equipment, while the power-down function helps reduce consumption when touch input is not required. A variable reference voltage from 1 V to VCC allows the analog conversion range to be matched to system requirements. The 16-lead SSOP package also provides a compact surface-mount format suitable for space-constrained control boards.
In operation, the host processor controls the ADS7845E through its synchronous serial interface. The controller drives the resistive panel, samples the resulting analog voltage, and returns a 12-bit conversion result. Ratiometric operation references the measurement to the supply voltage, which can reduce sensitivity to supply variation when the host and touch interface share the same reference. The auxiliary analog inputs extend the device beyond touch-coordinate acquisition when additional analog measurements are required.
Typical implementations include portable data-acquisition terminals, industrial operator panels, laboratory instruments, medical-device interfaces, and compact HMI systems. The 125 kHz conversion rate supports responsive coordinate acquisition, while the 2.7 V to 5 V supply range permits use with both 3.3 V and 5 V embedded systems. Designers should select the correct SSOP footprint and follow the manufacturer pin-description and recommended application-circuit tables when assigning signals.
A key design consideration is preserving clean, low-impedance analog routing between the controller and the touch-panel connector. Keep the touch and auxiliary input traces short, place bypass capacitance close to the supply pins, and avoid switching-regulator nodes beneath the analog signal paths. The measured coordinate accuracy also depends on panel calibration, active-area mapping, and mechanical repeatability, not only on the controller’s 12-bit converter.
This product record combines the manufacturer’s electrical characteristics with practical interface guidance, package details, and drop-in replacement analysis. It also organizes the key design trade-offs for engineers evaluating the ADS7845E against pin-compatible ordering variants and other touch-screen-controller families.
直接替换替代料: ADS7845E ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
ADS7845EG4
✅ 直接替换📋 参考替代料(不在目录中)
ADS7845ID
✅ 直接替换 ⚠️ 规格未核验📋 参考替代料(不在目录中)
ADS7845E 最大额定值与电气特性
| Product Type | 5-wire resistive touch-screen controller |
| ADC Resolution | 12 bit |
| Conversion Method | Ratiometric conversion |
| Maximum Conversion Rate | 125 kHz |
| Supply Voltage Range | 2.7 V to 5 V |
| Reference Voltage Range | 1 V to VCC |
| ADC Input Voltage Range | 0 V to VREF |
| Typical Power Dissipation | 750 uW at 2.7 V and 125 kHz throughput |
| Auxiliary Analog Inputs | 2 inputs |
| Serial Interface | Synchronous serial, SPI |
| Power-Down Control | Yes |
| 工作温度范围 | -40 C to +85 C |
| 封装 | 16-lead SSOP |
| 安装类型 | Surface mount |
ADS7845E 16-lead ssop 引脚配置指南
ADS7845E(16-lead ssop 封装)的引脚配置。 该模拟元件具有输入、输出和电源引脚。请参阅制造商数据手册以了解失调调零、补偿和使能引脚配置。适用于信号调理和放大器电路。
暂无详细引脚数据: ADS7845E.
请参阅 数据手册 以查看完整引脚配置。
典型应用
ADS7845E 适用于 6 应用s: Portable Data-Acquisition Terminal, Industrial Operator Panel, Laboratory Instrument Interface, Medical Device Touch Interface, Embedded Human-Interface System, Compact Control Console.
Portable Data-Acquisition Terminal
The ADS7845E fits a portable instrument that combines a 5-wire resistive panel with a 3.3 V embedded processor. Its 12-bit resolution supports coordinate calculation, while the 125 kHz conversion rate permits responsive sampling during pointer movement. The 2.7 V to 5 V single-supply range allows operation from the same rail family used by the host. Full power-down support is valuable when the terminal is inactive, and the 16-lead SSOP keeps the controller footprint compact. Calibration should map the raw ratiometric results to the panel’s usable active area.
Industrial Operator Panel
An industrial HMI using a 5-wire resistive touchscreen can use the ADS7845E to acquire X and Y coordinates from a single 2.7 V to 5 V supply. The controller’s 12-bit conversion and maximum 125 kHz rate are appropriate for menu navigation and machine-control interfaces, while ratiometric operation helps relate measurements to the system supply. The two auxiliary analog inputs can also support additional analog measurements if the board architecture permits. PCB layout should isolate touch signals from switching nodes and motor-control return paths.
Laboratory Instrument Interface
The ADS7845E is appropriate for a laboratory instrument with a resistive touch display and a host processor requiring straightforward serial data transfer. The synchronous serial interface and 12-bit ADC result support digital coordinate acquisition without a separate external ADC. Its 750 uW typical dissipation at 2.7 V and 125 kHz throughput is useful for portable bench equipment, while power-down control can reduce consumption between measurements. For precise readouts, combine panel calibration with hardware layout that minimizes analog-trace pickup.
Medical Device Touch Interface
A medical-device operator interface can employ the ADS7845E when the display is a 5-wire resistive panel and the control board operates from 2.7 V to 5 V. The 12-bit conversion resolution and 125 kHz maximum rate support responsive control entry, while full power-down control helps manage system consumption. Designers should keep sensitive patient-signal circuitry separate from the touch interface and validate the complete display assembly for electrical safety and usability. Panel calibration and fault-response behavior must also be verified as part of the finished system.
Embedded Human-Interface System
The ADS7845E is well suited to an embedded HMI requiring accurate resistive-touch acquisition and a compact controller footprint. Its 12-bit ratiometric conversion, 125 kHz sampling capability, and synchronous serial connection allow the host processor to poll X and Y measurements without continuous high-rate conversion. The single 2.7 V to 5 V supply supports common embedded rails, and power-down operation simplifies state management. Production designs should include calibration for display-to-panel alignment and controls for edge-of-screen behavior.
Compact Control Console
A compact control console can use the ADS7845E to convert analog touch-panel signals into 12-bit digital coordinates for a host controller. The 16-lead SSOP package limits board area, and the 125 kHz maximum conversion rate supports responsive pointer tracking. Operation from 3.3 V or 5 V simplifies integration with embedded logic, while ratiometric conversion provides a stable reference relative to the supply. Keep the touch connector and analog traces away from high-current outputs, and account for display and panel tolerances during calibration.
工程参考数据: ADS7845E ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | ADS7845EG4 | ADS7845ID |
|---|---|---|---|
| Package | 16-lead SSOP | 16-lead SSOP - same | 16-lead SSOP - same |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments |
| Touch-Screen Type | 5-wire resistive | 5-wire resistive | 5-wire resistive |
| ADC Resolution | 12 bit | 12 bit | 12 bit |
| Maximum Conversion Rate | 125 kHz | 125 kHz | 125 kHz |
| Supply Voltage Range | 2.7 V to 5 V | 2.7 V to 5 V | 2.7 V to 5 V |
| Conversion Method | Ratiometric | Ratiometric | Ratiometric |
| Power-Down Control | Yes | Yes | Yes |
| Auxiliary Analog Inputs | 2 inputs | 2 inputs | 2 inputs |
| Reference Voltage Range | 1 V to VCC | 1 V to VCC | 1 V to VCC |
关键差异点
- Higher sampling capability than lower-rate touch controllers (对比 ADS7845EG4)
- Single-supply operation supports common embedded rails (对比 ADS7845ID)
- Integrated auxiliary measurement capability (对比 ADS7845EG4)
设计说明
Route the touch-panel and auxiliary analog signals as short, continuous traces, and place the supply bypass capacitor close to the controller’s supply and ground pins. Avoid running these inputs beneath digital clocks, switching-regulator inductors, or high-current return paths. The SSOP footprint requires careful pad alignment because lead spacing and package orientation errors can connect adjacent touch-drive and serial-interface nets incorrectly.
Do not confuse the ADS7845 with a 4-wire resistive controller: the ADS7845E is intended for a 5-wire panel, and correct panel excitation and sensing depend on that topology. Confirm that the host serial interface levels match the controller supply. After assembly, calibrate both axes using the panel’s physical active limits because controller resolution alone does not correct mechanical offsets, edge nonlinearity, or display-to-touch misalignment.
Use power-down control when the display can remain idle, but verify that the host wakes the controller and completes panel settling before taking the first coordinate sample. The typical dissipation figure of 750 uW applies at 2.7 V with a 125 kHz throughput rate and does not include every external load. Account for panel-drive current, bypass-capacitor ripple, and conversion activity when budgeting the overall controller supply current.
合规信息
The cited product information does not explicitly state the RoHS, REACH, lead-free, halogen-free, conflict-minerals, or AEC-Q100 status of the exact ADS7845E ordering code. The device is not identified as an automotive-qualified part.