ADS820U/1K - 10-Bit 20-MSPS ADC | Texas Instruments
料号: ADS820U/1K ✓ 量产中ADS820U/1K 概述
An analog-to-digital converter is a data-acquisition IC that converts a continuous analog voltage into a numeric code for processing by a microcontroller, DSP, FPGA, or embedded control system. The ADS820 belongs to the ADC hierarchy, where resolution describes the number of representable levels and sampling rate describes how quickly the input is captured. A 10-bit converter provides 1,024 possible codes, while 20 MSPS supports high-speed measurement, waveform capture, communications, and industrial control functions.
Key characteristics include a 10-bit conversion resolution, a maximum conversion rate of 20 million samples per second, one analog input channel, and a 28-SOIC surface-mount package. The internal track-and-hold stage captures the analog input for conversion, and the integrated reference simplifies the external analog circuitry. A power-down function supports systems that need to reduce consumption when conversion activity is not required.
The converter uses a pipelined architecture, allowing successive conversion stages to support the device's 20-MSPS throughput. This is useful for acquisition blocks where sampling cadence must be predictable. The 10-bit result provides a balance between data throughput and circuit complexity, making the ADS820U/1K suitable for designs that need faster sampling than a general-purpose low-speed ADC without requiring a high-resolution high-speed converter.
Typical uses include industrial process measurement, data acquisition, control-loop monitoring, waveform digitization, communications receivers, and embedded signal processing. In these systems, the ADC can provide a binary output representing the sampled analog voltage to a parallel digital processor or interface logic. Differential input operation can also support noise-resistant sensing when the source can present a balanced signal.
When laying out a design, place input, reference, decoupling, and digital-interface connections according to the manufacturer datasheet. Pay particular attention to source impedance, sampling-clock timing, output timing, and grounding. Because the converter combines analog acquisition with digital signals, separating analog and digital return paths and minimizing clock coupling can improve repeatability and reduce conversion noise.
This page organizes the ADS820U/1K specifications, package information, sourcing route, and application guidance into one engineering-focused reference. It also distinguishes the verified device characteristics from specifications that must be confirmed in the manufacturer datasheet before layout, timing, or signal-chain calculations are performed.
直接替换替代料: ADS820U/1K ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
本系列中的变体
可与以下型号直接替换的同系列型号: ADS820U/1K (相同外形与封装尺寸) ——差异在于 Architecture, Input Type, Internal Reference, Power-Down Feature.
ADS820U/1K 最大额定值与电气特性
| Converter Type | Monolithic pipeline ADC |
| 分辨率 | 10 bit |
| 采样率 | 20 MSPS |
| Number of Input Channels | 1 channel |
| Input Type | Single-ended or differential |
| Architecture | Pipelined |
| Process Technology | Small-geometry CMOS |
| Internal Track-and-Hold | Yes |
| Internal Reference | Yes |
| Power-Down Feature | Yes |
| 封装 | 28-pin SOIC |
| 安装类型 | Surface mount |
| 工作温度 | -40°C to +85°C |
| Quantity of Binary Output Codes | 1,024 codes |
ADS820U/1K 28-pin soic 引脚配置指南
ADS820U/1K(28-pin soic 封装)的引脚配置。 该模拟元件具有输入、输出和电源引脚。请参阅制造商数据手册以了解失调调零、补偿和使能引脚配置。适用于信号调理和放大器电路。
暂无详细引脚数据: ADS820U/1K.
请参阅 数据手册 以查看完整引脚配置。
典型应用
ADS820U/1K 适用于 6 应用s: Industrial Process Data Acquisition, Communications Receiver Digitization, Waveform Digitization, Embedded Control and Monitoring, Audio and Vibration Signal Monitoring, Automated Test and Measurement.
Industrial Process Data Acquisition
The ADS820U/1K fits industrial acquisition cards that sample analog process signals at up to 20 MSPS. A 10-bit result provides 1,024 digital codes, allowing a controller to capture rapidly changing sensor, actuator, or bridge signals without implementing a separate track-and-hold circuit. The internal reference and single-ended or differential input support can simplify the analog front end. In a factory design, the converter should sit close to the input connector and protection network, while clocks and digital outputs should be routed away from sensitive analog nodes. Differential wiring is preferable for long cable runs or noisy environments because it can reject common-mode disturbance.
Communications Receiver Digitization
The ADS820U/1K is appropriate for communications receivers requiring periodic sampling of a received analog waveform at rates up to 20 MSPS. The pipelined architecture supports continuous sampling, while the internal track-and-hold reduces the number of external sampling components needed ahead of the converter. In a receiver implementation, the 10-bit output can feed packetization, demodulation, or FPGA-based filtering logic. The design must account for the permitted input bandwidth and conversion timing listed in the TI datasheet, because those limits determine whether full-scale signal energy remains within the converter’s usable range.
Waveform Digitization
A 20-MSPS sampling rate makes the ADS820U/1K useful for capturing repetitive waveforms rather than slow process trends. The 10-bit converter can represent each sample with one of 1,024 codes, and its internal track-and-hold supports the sampling front end. In an oscilloscope-like or condition-monitoring subsystem, the ADC output can feed memory, a digital filter, or an FPGA for later analysis. The sampling clock should be derived from a stable low-jitter source, and input attenuation should be scaled so normal operating signals remain within the converter’s specified range without clipping.
Embedded Control and Monitoring
The ADS820U/1K can serve as the sensing element in a fast embedded control or diagnostic system when 10-bit resolution is sufficient. At 20 MSPS, it can sample transient events more quickly than a conventional slow ADC, while the power-down function allows a duty-cycled design to reduce activity between measurement bursts. A microcontroller or FPGA can receive the digital result and apply filtering, thresholds, or fault detection. Designers should verify the exact digital interface and output timing because the converter is not specified here by bus protocol; those details determine the required bridge logic and processor resources.
Audio and Vibration Signal Monitoring
The ADS820U/1K can digitize vibration, acoustic, or other wideband monitoring signals when a 10-bit measurement and 20-MSPS sampling rate meet the application requirements. Differential input operation can help reject common-mode noise when the transducer and analog front end are arranged for a balanced signal. The converter output may be processed by a DSP or FPGA for spectral analysis or event detection. Input conditioning remains important: use an anti-alias filter appropriate to the 20-MSPS sampling rate, establish the expected full-scale level, and keep the sampling clock and digital return paths separated from the transducer signal.
Automated Test and Measurement
The ADS820U/1K can act as the sampling front end in automated test equipment that must characterize changing analog conditions. Its 20-MSPS throughput supports fast test sequences, and the internal reference and track-and-hold reduce the number of external active components. A fixture controller can collect the 10-bit conversion results, apply calibration, and flag readings outside predetermined limits. For accurate measurements, account for reference tolerance, input leakage, settling time, clock timing, and board-level noise in the calibration model. Use the manufacturer application and timing information to determine whether a sampling switch, driver, or additional reference is required.
工程参考数据: ADS820U/1K ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | ADS820U |
|---|---|---|
| Brand | Texas Instruments | Texas Instruments |
| Package | 28-SOIC | 28-SOIC - same package |
| Resolution | 10 bit | 10 bit |
| Sampling Rate | 20 MSPS | 20 MSPS |
| Input Channels | 1 channel | 1 channel |
| Architecture | Pipelined | Pipelined |
| Input Configuration | Single-ended or differential | Single-ended or differential |
| Internal Functions | Internal track-and-hold, internal reference, power-down | Internal track-and-hold, internal reference, power-down |
| Process Technology | Small-geometry CMOS | Small-geometry CMOS |
| Ordering Suffix | /1K | No /1K suffix |
关键差异点
- Maintains the same core conversion specifications as the identified same-package option (对比 ADS820U)
- Uses the same 28-SOIC package outline for board-level reuse (对比 ADS820U)
- Integrates key acquisition functions (对比 ADS820U)
设计说明
Route the analog input directly to the converter and keep the input path short, with the external protection and conditioning network positioned close to the package. Place analog and digital grounds according to the TI datasheet ground configuration and provide a quiet return for the reference and supply connections. A 28-SOIC package is easy to route, but pin escapes on a fine-pitch board can still force long traces. Review the recommended layout in the manufacturer datasheet before fixing connector, reference, and digital-bus positions.
Use a low-jitter sampling clock and keep the clock route away from the analog input and reference nodes. The converter includes an internal track-and-hold stage, but the external driver and acquisition network still determine how faithfully the source voltage is captured. Confirm acquisition time, source-impedance limits, input bandwidth, and settling requirements in the TI manufacturer datasheet. If the source impedance is high, add a suitable buffer rather than relying on capacitive loading to correct the error.
Do not treat the 10-bit resolution as the complete accuracy specification. Offset, gain error, integral nonlinearity, differential nonlinearity, reference error, noise, and PCB effects can each affect the usable result. Also do not assume that the ADS820U and ADS820U/1K identifiers are interchangeable for purchasing without checking the customer’s suffix, packing, and traceability requirements. Validate the complete analog chain with representative signals and use the manufacturer’s timing and recommended application circuit as the layout reference.
合规信息
No specific RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals declarations were identified for the exact ADS820U/1K ordering code. AEC-Q100 is not applicable to this industrial data-conversion product.