ATMEGA128-16MC - 8-Bit AVR MCU 16MHz 128KB Flash | Microchip
料号： ATMEGA128-16MC ✓ 量产中| 数量 | 单价 | 小计 |
|---|---|---|
| 1 | $9.8 | $9.80 |
| 10 | $8.9 | $89.00 |
| 100 | $7.95 | $795.00 |
| 500 | $7.2 | $3,600.00 |
| 1,000 | $6.65 | $6,650.00 |
ATMEGA128-16MC 概述
An 8-bit AVR microcontroller is a Harvard-architecture RISC processor in the broader hierarchy of MCUs (microcontroller -> embedded processor -> system-on-chip building block). The AVR family is known for executing most of its powerful instruction set in a single clock cycle, giving high code efficiency and deterministic timing for embedded control systems.
Key features include 133 powerful instructions (most single-cycle), 32 x 8-bit general-purpose working registers, 53 programmable I/O lines, and a self-programming Flash architecture enabling field firmware updates. The 8-channel 10-bit ADC supports direct analog sensor interfacing, while dual USARTs, SPI, and TWI (I2C-compatible) cover common embedded communication needs.
Technically, the ATmega128 pairs an advanced RISC core with a rich peripheral set: two 8-bit timers, two 16-bit timers with PWM capability, a watchdog timer, an on-chip analog comparator, and internal/external interrupt sources. The JTAG boundary-scan and on-chip-debug capability shortens development cycles on dense, no-lead packages that are otherwise hard to probe. According to the ATmega128 datasheet, the device is 100% pin compatible with the ATmega103 and can replace it on existing PCBs.
Typical applications include industrial automation and control panels, building and HVAC controllers, instrumentation with analog sensor inputs, and legacy ATmega103 board upgrades. The commercial temperature grade (0C to +70C) suits indoor industrial and consumer products.
Design consideration: at 16 MHz operation the ATMEGA128-16MC requires a 4.5 V to 5.5 V supply; for 3 V systems choose the ATmega128L speed-voltage grade or drop the clock below the low-voltage frequency limit.
This page synthesizes distributor sourcing data, same-family drop-in alternatives, and practical design notes not found in the manufacturer datasheet.
直接替换替代料： ATMEGA128-16MC ——相同封装，引脚兼容。需要 PCB 改动的不同封装料号已排除。
本系列中的变体
可与以下型号直接替换的同系列型号： ATMEGA128-16MC （相同外形与封装尺寸） ——差异在于 Package, ADC, Communication Interfaces, Instruction Set, Program Memory Size.
快速对比工具——选择替代料号进行并排对比：
ATMEGA128-16MU
✅ 直接替换✓ 有现货
$6.4 / 个
查看数据手册 →ATMEGA128-16MN
✅ 直接替换✓ 有现货
$7.44 / 个
查看数据手册 →ATMEGA128-16MCUR
✅ 直接替换📋 参考替代料（不在目录中）
ATMEGA1281-16MUR
✅ 直接替换✓ 有现货
$8.78 / 个
查看数据手册 →ATMEGA128-16MC 最大额定值与电气特性
| Core Architecture | 8-bit AVR RISC |
| Max CPU Frequency | 16 MHz |
| Throughput | Up to 16 MIPS at 16 MHz |
| Flash Program Memory | 128 KB (64K x 16) In-System Programmable |
| SRAM | 4 KB |
| EEPROM | 4 KB |
| ADC | 8-channel, 10-bit |
| Instruction Set | 133 instructions, most single-clock-cycle |
| General Purpose Registers | 32 x 8-bit |
| I/O Lines | 53 programmable I/O |
| Communication Interfaces | 2x USART, SPI, TWI (I2C-compatible) |
| Timers | 2x 8-bit, 2x 16-bit with PWM |
| Debug / Boundary Scan | JTAG interface for on-chip debugging |
| Operating Temperature Grade | Commercial (0C to +70C) |
| 封装 | 64-QFN (MLF), 9x9 mm, no-lead |
| 安装类型 | Surface Mount |
ATMEGA128-16MC 64-qfn (mlf), 9x9 mm, no-lead 引脚配置指南
ATMEGA128-16MC（64-qfn (mlf), 9x9 mm, no-lead 封装）的引脚配置。 该数字 IC 包含 GPIO、通信接口（UART、SPI、I2C）和电源引脚。请参阅制造商数据手册以了解复用引脚功能和配置选项。对嵌入式系统设计和 PCB 布局至关重要。
暂无详细引脚数据： ATMEGA128-16MC.
请参阅 数据手册 以查看完整引脚配置。
典型应用
ATMEGA128-16MC 适用于 6 应用s: Industrial Automation and Control, ATmega103 Legacy Board Upgrade, Sensor Data Acquisition Systems, Embedded Communication Nodes, Instrumentation and Test Equipment, Building Control and HVAC Controllers.
Industrial Automation and Control
The ATMEGA128-16MC fits industrial controllers because its 16 MIPS AVR core handles deterministic scan loops, while 128 KB Flash accommodates protocol stacks and HMI logic, and 53 I/O lines drive relays, optocouplers, and status LEDs directly. Dual USARTs support Modbus RTU on one port and a service console on the other, with SPI and TWI connecting ADCs, RTCs, and EEPROM. The 8-channel 10-bit ADC reads analog process variables such as 0-10 V or 4-20 mA signals after conditioning. The commercial 0C to +70C grade suits enclosed control cabinets, and the 64-QFN no-lead package provides a compact, thermally efficient footprint for dense I/O boards. JTAG enables field debugging without soldering wires to fine-pitch pads.
推荐
ATmega103 Legacy Board Upgrade
The ATmega128 is explicitly 100% pin compatible with the ATmega103, making the ATMEGA128-16MC the standard upgrade path for sustaining legacy PCB designs, as documented in the Microchip datasheet and the application note 'Replacing ATmega103 by ATmega128'. Engineers gain 128 KB self-programming Flash versus the ATmega103's smaller memory, plus a hardware multiplier-class RISC core and richer peripherals, without a PCB respin. The M103C compatibility fuse eases firmware migration. In a 64-QFN (MLF) no-lead package, the part also offers better thermal performance than older packaged variants. Before conversion, review fuse settings, EEPROM data mapping, and JTAG enable state, since these differ from ATmega103 defaults and affect programming and debug tooling.
推荐
Sensor Data Acquisition Systems
For multi-channel data loggers, the ATMEGA128-16MC's 8-channel 10-bit ADC directly digitizes temperature, pressure, and humidity sensor outputs, while 4 KB EEPROM stores calibration constants that survive power cycles and 4 KB SRAM buffers sampled data. The 16 MHz core provides ample headroom for oversampling, filtering, and scaling algorithms between conversions. TWI (I2C) links additional external ADCs or display drivers, SPI connects high-speed Flash for local storage, and a USART streams results to a host or radio module. The JTAG interface supports in-field firmware updates for changing calibration routines, and the compact 9x9 mm QFN keeps the acquisition board small enough for distributed sensor nodes inside commercial environments.
推荐
Embedded Communication Nodes
The ATMEGA128-16MC suits networked field nodes because its dual USARTs allow simultaneous modem/RS-485 communication and a local service interface, while hardware SPI and TWI offload connectivity to RF modules, CAN controllers, or Ethernet MACs such as common SPI-Ethernet bridges. The 128 KB Flash holds complete protocol stacks - including TCP/IP or Modbus variants - plus web-formatted diagnostics, and the 16 MIPS core sustains line-rate UART traffic with interrupt-driven buffering. Code density benefits from the AVR's mostly single-cycle instruction set and 32 general-purpose registers. Field-deployed nodes appreciate the self-programming Flash: the MCU can rewrite its own application section over the network for remote firmware upgrades without a programmer on site.
推荐
Instrumentation and Test Equipment
Bench and portable instruments use the ATMEGA128-16MC for front-panel control, measurement sequencing, and result formatting. The 10-bit ADC handles auxiliary analog inputs, the 16-bit timers generate precise PWM or capture external events, and the analog comparator supports threshold detection. A graphics LCD is driven via parallel or SPI interfaces using the 53 I/O lines, while a USART links the instrument to a PC for logging. The 128 KB Flash holds menus, fonts, and math routines, and 4 KB SRAM supports buffers for waveform snapshots. JTAG on-chip debugging is especially valuable here: instrument firmware with stateful menus is hard to debug with print statements alone, and the QFN package leaves no probe points.
推荐
Building Control and HVAC Controllers
HVAC zone controllers exploit the ATMEGA128-16MC's combination of analog and digital integration: the 8-channel ADC reads NTC thermistors and pressure transducers, timer PWM outputs drive triac or SSR heater control at mains-safe isolation, and TWI connects real-time clocks and humidity sensors. Dual USARTs support BACnet-over-serial or proprietary building buses. The 128 KB Flash comfortably holds scheduling tables, PID loops, and logging firmware, and 4 KB EEPROM retains setpoints and runtime hours through outages. The commercial 0C to +70C grade matches indoor controller enclosures, and the self-programming Flash enables fleet firmware updates via the service UART, reducing truck rolls for installed-base maintenance across large buildings.
推荐
推荐产品汇总
工程参考数据： ATMEGA128-16MC ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | ATMEGA128-16MU | ATMEGA128-16MN | ATMEGA1281-16MUR | ATMEGA128-16AC |
|---|---|---|---|---|---|
| Brand | Microchip Technology (Atmel) | Microchip Technology (Atmel) | Microchip Technology (Atmel) | Microchip Technology (Atmel) | Microchip Technology (Atmel) |
| Package | 64-QFN (MLF) 9x9 mm | 64-QFN (MLF) 9x9 mm - same | 64-QFN (MLF) 9x9 mm - same | 64-QFN (MLF) 9x9 mm - same footprint class, pinout differs | TQFP-64 - footprint change required |
| Max CPU Frequency | 16 MHz | 16 MHz | 16 MHz | 16 MHz | 16 MHz |
| Flash Memory | 128 KB ISP Flash | 128 KB | 128 KB | 128 KB | 128 KB |
| SRAM | 4 KB | 4 KB | 4 KB | 8 KB | 4 KB |
| EEPROM | 4 KB | 4 KB | 4 KB | 4 KB | 4 KB |
| ADC | 8-channel, 10-bit | 8-channel, 10-bit | 8-channel, 10-bit | 8-channel, 10-bit | 8-channel, 10-bit |
| Temperature Grade | Commercial (0C to +70C) | Commercial (0C to +70C) | Commercial (0C to +70C) | Industrial (-40C to +85C) | Commercial (0C to +70C) |
| Drop-in on Same Footprint | Reference (64-QFN MLF) | Yes - pin-to-pin | Yes - pin-to-pin | Verify pin table - not 100% identical | No - different package |
关键差异点
- 100% pin-compatible ATmega103 replacement （对比 ATMEGA1281-16MUR)
- Large 128 KB self-programming Flash enables field firmware updates （对比 ATMEGA88PA-MU)
- JTAG on-chip debugging and boundary scan （对比 ATMEGA128-16AC (TQFP variant))
设计说明
The '-16' speed grade requires the 4.5 V to 5.5 V supply range for guaranteed 16 MHz operation (ATmega128 datasheet voltage-versus-frequency limits). Provide a clean 5 V rail with 100 nF ceramic decoupling on each VCC/AVCC pin pair placed within 5 mm of the pads, plus 10 uF bulk capacitance near the QFN. If the board also runs 3.3 V logic, level-shift or verify VIH margins on USART/SPI lines, since the MCU I/O swings 0 V to VCC. Do not rely on the -16MC below 4.5 V at 16 MHz - timing is not characterized there.
The 64-QFN (MLF) 9x9 mm no-lead package requires a well-defined land pattern with an exposed center pad. Connect the center pad to a ground pour with an array of thermal vias (typically 3x3 or 4x4, ~0.3 mm drill) to provide both the primary return path and heat spreading. Solder-paste stencil aperture design matters for no-lead parts: use segmented apertures to avoid excessive paste under the pad causing floating or bridging. AOI/X-ray inspection is recommended because the peripheral pads are partially hidden under the package body.
Three frequent ATmega128 pitfalls: (1) JTAG is enabled by default and owns pins PF7-PF4 - set the JTAGEN fuse appropriately if you need those as I/O. (2) The M103C compatibility fuse (added for ATmega103 migration) changes SRAM mapping and some behaviors; clear it for native ATmega128 operation. (3) The 128 KB address space exceeds the 16-bit program counter's direct range, so constant data access across the 64 KB boundary requires the RAMPZ register - handled transparently by compilers such as CodeVisionAVR, but a classic bug source in hand-written assembly.
Drive the 16 MHz clock with a crystal plus the datasheet-recommended load capacitors, keeping trace lengths under 20 mm and guarding with ground. The XTAL2 output swings fast enough to radiate; a series resistor (typically 100-1k ohm, tune for clean edge) reduces EMI if the crystal sits close to the MCU. For ADC accuracy, route analog channel traces away from the crystal, PWM outputs, and USART lines, and tie AVCC to VCC through an RC filter (e.g., 10 ohm + 100 nF) per the datasheet's ADC noise-reduction guidance.
合规信息
Compliance status not stated in the provided web data; the -16MC is an Atmel-era orderable code whose RoHS/lead-free status should be confirmed on the Microchip product page or by requesting a certificate of conformance from the distributor.
