ATSAMD20E15A-AN - 32KB Flash ARM Cortex-M0+ MCU | Microchip
料号： ATSAMD20E15A-AN ✓ 量产中| 数量 | 单价 | 小计 |
|---|---|---|
| 1 | $3.12 | $3.12 |
| 10 | $2.78 | $27.80 |
| 100 | $2.35 | $235.00 |
| 500 | $2.05 | $1,025.00 |
| 1,000 | $1.82 | $1,820.00 |
| 3,000 | $1.55 | $4,650.00 |
ATSAMD20E15A-AN 概述
A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program and data memory, peripherals, and I/O on one die. The ARM Cortex-M0+ is the smallest and most energy-efficient member of the ARM Cortex-M processor family, designed for embedded applications where deterministic real-time response and ultra-low power consumption are required. The SAM D20 sits in the hierarchy as: Cortex-M0+ core -> ARM Cortex-M family -> 32-bit RISC microcontroller -> embedded processor -> semiconductor IC, making it ideal for cost-sensitive yet feature-rich IoT and consumer designs.
Key differentiating features include the SERCOM (Serial Communication Interface) modules that can be independently configured as UART, SPI, or I2C, plus a hardware Peripheral Touch Controller for capacitive touch buttons and sliders without external components. The 12-bit ADC delivers up to 350ksps with internal voltage reference, while the 10-bit DAC supports waveform generation. Multiple Sleep modes (Idle, Standby, Backup) and a dedicated RTC with calendar mode achieve sleep currents below 5 microamps.
Typical applications span home automation endpoints (smart thermostats, sensor hubs), consumer electronics (wearable accessories, toys), metering (energy and water monitors), and industrial controls (HMI panels, low-end PLCs). The wide 1.62V to 3.63V operating range and AEC-Q100 qualified variants simplify designs that target both battery-powered and 24V industrial bus environments.
When designing with the ATSAMD20E15A-AN, ensure the on-chip voltage regulator's bulk capacitor meets Microchip's reference design (typically 1uF X7R). Decoupling capacitors should be placed within 2mm of each supply pin, and unused SERCOM pads can be repurposed as GPIO. Programming is supported via Atmel-ICE or Curiosity Nano boards through the SWD interface.
直接替换替代料： ATSAMD20E15A-AN ——相同封装，引脚兼容。需要 PCB 改动的不同封装料号已排除。
本系列中的变体
可与以下型号直接替换的同系列型号： ATSAMD20E15A-AN （相同外形与封装尺寸） ——差异在于 ADC, Package, Operating Temperature, MSL Level, SERCOM Modules.
快速对比工具——选择替代料号进行并排对比：
ATSAMD20E14A-AN
✅ 直接替换✓ 有现货
$1.62 / 个
查看数据手册 →ATSAMD20E14B-AUT
✅ 直接替换✓ 有现货
$1.21 / 个
查看数据手册 →ATSAMD20E14B-AU
✅ 直接替换✓ 有现货
$1.45 / 个
查看数据手册 →ATSAMD20E14B-MUT
✅ 直接替换✓ 有现货
$0.95 / 个
查看数据手册 →ATSAMD10D14A-SSNT
✅ 直接替换✓ 有现货
$1.36 / 个
查看数据手册 →ATSAMD11D14A-MNT
✅ 直接替换✓ 有现货
$1.2 / 个
查看数据手册 →ATSAMD20E15A-AN 最大额定值与电气特性
| Core Architecture | ARM Cortex-M0+ (32-bit) |
| 最大时钟频率 | 48 MHz |
| Flash Memory | 32 KB |
| SRAM | 4 KB |
| Supply Voltage Range | 1.62 V to 3.63 V |
| 工作温度 | -40 C to +105 C |
| CoreMark Performance | 2.14 CoreMark/MHz |
| ADC Resolution | 12-bit |
| DAC Resolution | 10-bit |
| Peripheral Touch Controller | 256 channels |
| SERCOM Modules | 6 (configurable UART/SPI/I2C) |
| 封装 | 32-pin TQFP |
| 安装类型 | Surface Mount |
| RoHS 状态 | Compliant |
| Lead Free | Yes |
ATSAMD20E15A-AN 引脚配置
| 引脚 1 | PA00 — GPIO/SERCOM1[0]/ADC[0] |
| 引脚 2 | PA01 — GPIO/SERCOM1[1]/ADC[1] |
| 引脚 3 | PA02 — GPIO/SERCOM0[0]/ADC[2] |
| 引脚 4 | VDD — Digital supply voltage |
| 引脚 5 | GND — Ground |
| 引脚 6 | PA03 — GPIO/SERCOM0[1]/ADC[3]/VREFA |
| 引脚 7 | PA04 — GPIO/SERCOM0[2]/ADC[4] |
| 引脚 8 | PA05 — GPIO/SERCOM0[3]/ADC[5] |
| 引脚 9 | PA06 — GPIO/SERCOM2[0]/ADC[6] |
| 引脚 10 | PA07 — GPIO/SERCOM2[1]/ADC[7] |
| 引脚 11 | PA08 — GPIO/SERCOM2[2]/ADC[8]/NMI |
| 引脚 12 | PA09 — GPIO/SERCOM2[3]/ADC[9] |
| 引脚 13 | PA10 — GPIO/SERCOM0[2]/ADC[10] |
| 引脚 14 | PA11 — GPIO/SERCOM0[3]/ADC[11] |
| 引脚 15 | PA14 — GPIO/SERCOM2[2]/XIN |
| 引脚 16 | PA15 — GPIO/SERCOM2[3]/XOUT |
| 引脚 17 | PA16 — GPIO/SERCOM1[0]/PTC[X0] |
| 引脚 18 | PA17 — GPIO/SERCOM1[1]/PTC[X1] |
| 引脚 19 | PA18 — GPIO/SERCOM1[2]/PTC[X2] |
| 引脚 20 | PA19 — GPIO/SERCOM1[3]/PTC[X3] |
| 引脚 21 | PA20 — GPIO/SERCOM5[2]/PTC[X4] |
| 引脚 22 | PA21 — GPIO/SERCOM5[3]/PTC[X5] |
| 引脚 23 | PA22 — GPIO/SERCOM3[0]/PTC[X6] |
| 引脚 24 | PA23 — GPIO/SERCOM3[1]/PTC[X7] |
| 引脚 25 | PA24 — GPIO/SERCOM3[2]/PTC[Y0] |
| 引脚 26 | PA25 — GPIO/SERCOM3[3]/PTC[Y1] |
| 引脚 27 | PA27 — GPIO/SERCOM5[3]/PTC[Y2] |
| 引脚 28 | PA28 — GPIO/SERCOM5[2]/PTC[Y3]/RESET |
| 引脚 29 | VDD — Digital supply voltage |
| 引脚 30 | GND — Ground |
| 引脚 31 | SWDIO — Serial Wire Debug I/O (PA31) |
| 引脚 32 | SWCLK — Serial Wire Debug Clock (PA30) |
典型应用
ATSAMD20E15A-AN 适用于 6 应用s: Home Automation Hubs, Consumer Wearables, Smart Energy Metering, Industrial Sensor Transmitters, Capacitive Touch User Interfaces, Battery-Powered IoT Edge Nodes.
Home Automation Hubs
The ATSAMD20E15A-AN is well suited for home automation endpoints such as smart thermostats, sensor hubs, and lighting controllers. Its 32-bit Cortex-M0+ at 48MHz executes Zigbee or Matter stack callbacks efficiently, while the 12-bit ADC with 350ksps supports temperature, humidity, and ambient light sensing through the 16 available analog channels. The six SERCOM modules configure flexibly as UART, SPI, or I2C, allowing simultaneous connection to sensors, wireless modules, and a local display. Low-power Backup mode with RTC running draws under 5 microamps, making battery-powered sensor nodes viable for multi-year deployments on two AA cells.
推荐
Consumer Wearables
Wearable bands and fitness trackers benefit from the ATSAMD20E15A-AN's combination of a Cortex-M0+ core, 256-channel Peripheral Touch Controller (PTC) for capacitive UI buttons, and 10-bit DAC for haptic feedback waveforms. At 48MHz the device delivers 2.14 CoreMark/MHz, enough to drive simple BLE link layer control and sensor fusion math. The 32KB Flash holds BLE stack plus application logic, while 4KB SRAM supports sensor buffering. Standby current below 5uA with RTC wakeup enables always-on step counting without daily charging.
推荐
Smart Energy Metering
In single-phase electricity meters and gas/water flow monitors, the ATSAMD20E15A-AN serves as the metrology MCU. The 12-bit ADC with 350ksps captures load current and voltage with sufficient resolution for class 1 accuracy metering, while the RTC with calendar mode handles time-of-use tariffs and tampering logging. The 32KB Flash supports DLMS/COSEM or IEC 62056 application code with secure firmware update via the on-chip NVMCTRL bootloader. Wide 1.62V to 3.63V supply tolerance allows direct battery backup or supercapacitor support during line outages.
推荐
Industrial Sensor Transmitters
Industrial 4-20mA loop-powered sensor transmitters and HMI panels use the ATSAMD20E15A-AN for signal conditioning and bus interfacing. The device's 1.62V to 3.63V range accepts common 3.3V and 5V-derived rails, and the 32-pin TQFP footprint supports standard industrial PCB layouts. The 12-bit ADC reads bridge pressure sensors or RTD-conditioned temperatures, while SERCOM modules drive RS-485 transceivers for Modbus RTU. AEC-Q100 qualified variants (ATSAMD20E15A-AUT) extend deployment to factory floor environments with extended -40C to +125C operation.
推荐
Capacitive Touch User Interfaces
The ATSAMD20E15A-AN's integrated 256-channel Peripheral Touch Controller (PTC) supports both self-capacitance and mutual-capacitance electrode patterns, enabling capacitive touch buttons, sliders, and wheels on appliances and consumer electronics without external touch ICs. Combined with the 32KB Flash for advanced UI firmware and the six SERCOM interfaces for display driving, the MCU replaces traditional mechanical keypads with waterproof glass-front designs. The 10-bit DAC generates analog feedback tones or piezo buzzer waveforms for user confirmation beeps.
推荐
Battery-Powered IoT Edge Nodes
Battery-powered IoT edge devices such as remote environmental monitors, asset trackers, and agricultural sensors rely on the ATSAMD20E15A-AN's multiple low-power modes. The Idle mode at 0.8mA/MHz keeps the core ready for sensor reads, Standby mode retains SRAM at 1.5uA, and Backup mode with RTC running drops to sub-5uA. The 12-bit ADC wakes the device on threshold-crossing events, while SERCOM-based I2C/SPI interfaces connect to environmental sensors and LoRa or sub-GHz radio modules for years-long battery life on a single lithium primary cell.
推荐
推荐产品汇总
工程参考数据： ATSAMD20E15A-AN ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | ATSAMD20E14A-AN | ATSAMD20E14B-AUT | ATSAMD20E14B-AU | ATSAMD20E14B-MUT |
|---|---|---|---|---|---|
| Package | 32-pin TQFP | 32-pin TQFP - same | 32-pin TQFP - same | 32-pin TQFP - same | 32-pin TQFP - same |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Core | ARM Cortex-M0+ | ARM Cortex-M0+ | ARM Cortex-M0+ | ARM Cortex-M0+ | ARM Cortex-M0+ |
| Maximum Clock | 48 MHz | 48 MHz | 48 MHz | 48 MHz | 48 MHz |
| Flash | 32 KB | 16 KB | 16 KB | 16 KB | 16 KB |
| SRAM | 4 KB | 4 KB | 4 KB | 4 KB | 4 KB |
| Operating Voltage | 1.62 V to 3.63 V | 1.62 V to 3.63 V | 1.62 V to 3.63 V | 1.62 V to 3.63 V | 1.62 V to 3.63 V |
| Operating Temperature | -40 C to +105 C | -40 C to +105 C | -40 C to +125 C (AEC-Q100) | -40 C to +105 C | -40 C to +125 C (AEC-Q100) |
关键差异点
- Highest Flash density in 32-pin TQFP SAMD20 family （对比 ATSAMD20E14A-AN)
- B-silicon revision includes errata fixes （对比 ATSAMD20E14B-AUT)
- Industrial temperature grade with full 48MHz operation （对比 ATSAMD20E14B-AUT (AEC-Q100))
设计说明
Place a 1uF X7R ceramic capacitor within 2mm of the VDD pin and a 10nF decoupling cap on each VDDIO supply pin. The on-chip LDO requires a minimum bulk capacitance of 1uF per the SAM D20 datasheet; lower values can cause core instability at 48MHz operation. Add bulk capacitance (4.7uF) at the board entry point to suppress transient voltage drops during SERCOM radio bursts.
The 32-pin TQFP requires 0.8mm pitch pads with 0.3mm signal traces escaped between pins. Route SWDIO and SWCLK with 50-ohm characteristic impedance and place test points for in-circuit programming access. The exposed pad (EP) on TQFP is the die substrate and should be soldered to a grounded copper pour for thermal dissipation and electrical reference.
Do not leave the RESET pin floating; tie PA28/RESET to VDD through a 10kohm pull-up and add a 1nF capacitor to ground for debouncing. Avoid configuring the XIN/XOUT pins as GPIO unless the external crystal is removed, as stray capacitance can prevent oscillator startup. When migrating from ATSAMD20E15A-AU (tray) to ATSAMD20E15A-ANT (tape and reel), verify the reel orientation matches pick-and-place feeders.
合规信息
RoHS and REACH compliant per Microchip product environmental certification. The ATSAMD20E15A-AN is industrial grade -40C to +105C; for AEC-Q100 qualified parts select ATSAMD20E15A-AUT or ATSAMD20E14B-MUT variants.
