ATSAMD20J15A-MN - ARM Cortex-M0+ MCU 48MHz 32KB Flash | Microchip
料号： ATSAMD20J15A-MN ✓ 量产中| 数量 | 单价 | 小计 |
|---|---|---|
| 1 | $2.05 | $2.05 |
| 10 | $1.84 | $18.40 |
| 100 | $1.49 | $149.00 |
| 500 | $1.21 | $605.00 |
| 1,000 | $0.85 | $850.00 |
ATSAMD20J15A-MN 概述
A microcontroller (MCU) is an integrated circuit that combines a processor core, program memory (Flash), data memory (SRAM), and a rich set of programmable peripherals (GPIO, timers, ADC, communication buses) on a single die. The ARM Cortex-M0+ is the smallest and most energy-efficient member of the ARM Cortex-M family, designed for deterministic real-time embedded control with a Thumb-2 instruction subset and a tightly coupled interrupt controller (NVIC). The ATSAMD20J15A belongs to the broader category hierarchy of microcontroller -> embedded processor -> system-on-chip (SoC) -> semiconductor IC, and uses Microchip's SAM D20 peripheral set that is shared across the family for firmware portability.
Key features include a 12-bit ADC with up to 16 channels, multiple SERCOM interfaces configurable as UART/SPI/I2C, a 16-bit timer/counter, a 32-bit RTC, and the Microchip Event System for inter-peripheral signaling without CPU intervention. The device reaches 2.14 CoreMark/MHz and offers low-power Sleep and Standby modes with fast wake-up, suited to battery-powered IoT endpoints. An on-chip 32kHz oscillator and a flexible clock management unit reduce external BOM.
Architecture-wise, the ATSAMD20J15A-MN uses a single-cycle hardware multiplier, a 32-bit system bus, and a separate AHB/APB bridge topology that allows high-speed peripherals (SERCOM, ADC) and low-speed peripherals to be clocked independently for power optimization. The Event System routes peripheral triggers over a dedicated network fabric, offloading many CPU tasks that would otherwise require interrupt-driven servicing.
Typical applications include smart-home sensor nodes, low-power wireless MCU companions (paired with an external radio), HVAC fan and damper controllers, electricity metering front-ends, USB human-interface class devices, and general-purpose industrial control boards. The wide temperature range also suits outdoor enclosures and lighting control gear.
When designing with this part, ensure the exposed pad (EP) on the 64-VFQFN is soldered to a sufficiently large copper pour for thermal dissipation and electrical ground reference; the package's HVQCCN terminal form does not provide stable operation without it. Decoupling capacitors should be placed as close as possible to each VDD pin pair per the SAM D20 hardware checklist.
This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet, giving engineers a single reference for component selection.
直接替换替代料： ATSAMD20J15A-MN ——相同封装，引脚兼容。需要 PCB 改动的不同封装料号已排除。
本系列中的变体
可与以下型号直接替换的同系列型号： ATSAMD20J15A-MN （相同外形与封装尺寸） ——差异在于 Package, ADC, Core Architecture, Operating Temperature Range, DAC.
快速对比工具——选择替代料号进行并排对比：
ATSAMD20J15A-MNT
✅ 直接替换✓ 有现货
$1.45 / 个
查看数据手册 →ATSAMD20J15A-CU
✅ 直接替换✓ 有现货
$2.05 / 个
查看数据手册 →ATSAMD20J15A-ANT
✅ 直接替换✓ 有现货
$1.65 / 个
查看数据手册 →ATSAMD20J15A-AUT
✅ 直接替换✓ 有现货
$1.85 / 个
查看数据手册 →ATSAMD20J15A-CNT
✅ 直接替换✓ 有现货
$2.54 / 个
查看数据手册 →ATSAMD20J14B-MU
✅ 直接替换✓ 有现货
$2.05 / 个
查看数据手册 →ATSAMD20J15A-MN 最大额定值与电气特性
| Core Architecture | ARM Cortex-M0+ |
| 数据总线宽度 | 32-bit |
| 最大时钟频率 | 48 MHz |
| Flash Program Memory | 32 KB (32K x 8) |
| SRAM | 4 KB |
| Operating Voltage Range | 1.6 V to 3.6 V |
| 工作温度范围 | -40C to +105C |
| 封装 | 64-VFQFN Exposed Pad (9x9 mm, HVQCCN) |
| 安装类型 | Surface Mount |
| ADC | 12-bit, up to 16 channels |
| Communication Interfaces | SERCOM (configurable UART/SPI/I2C) |
| Timers | 16-bit TC, 32-bit RTC |
| CoreMark per MHz | 2.14 |
| RoHS 状态 | Compliant |
ATSAMD20J15A-MN 64-vfqfn exposed pad (9x9 mm, hvqccn) 引脚配置指南
ATSAMD20J15A-MN（64-vfqfn exposed pad (9x9 mm, hvqccn) 封装）的引脚配置。 该数字 IC 包含 GPIO、通信接口（UART、SPI、I2C）和电源引脚。请参阅制造商数据手册以了解复用引脚功能和配置选项。对嵌入式系统设计和 PCB 布局至关重要。
暂无详细引脚数据： ATSAMD20J15A-MN.
请参阅 数据手册 以查看完整引脚配置。
典型应用
ATSAMD20J15A-MN 适用于 6 应用s: Smart Home Sensor Hubs, Industrial HVAC Fan Controllers, Electricity Metering Front-End, USB Human-Interface Devices, Battery-Powered IoT Sensor Nodes, Consumer Appliance Control Boards.
Smart Home Sensor Hubs
The ATSAMD20J15A-MN fits smart-home sensor hubs because its 48 MHz ARM Cortex-M0+ core delivers 2.14 CoreMark/MHz - enough headroom for Zigbee or Thread protocol bridging alongside sensor fusion. The 32 KB Flash accommodates typical firmware including device drivers, an application layer, and OTA stubs, while 4 KB SRAM supports FreeRTOS task stacks and short message buffers. Its 1.6-3.6V supply range lets it run directly from a Li-ion cell or a 3.3V regulator. The 12-bit ADC with up to 16 channels reads temperature, humidity, and ambient-light sensors without an external converter.
推荐
Industrial HVAC Fan Controllers
In HVAC fan and damper control, the ATSAMD20J15A-MN drives triac-controlled BLDC or AC fans through its GPIO and timer peripherals. The 16-bit TC timer provides accurate PWM with dead-time generation, and the Event System routes tachometer feedback to the CPU without interrupt overhead. Operating up to +105C, the device survives the engine-room thermal envelope. The 12-bit ADC samples motor current for closed-loop speed regulation; the 32 KB Flash holds the control algorithm and a Modbus or BACnet stack for building-automation network integration.
推荐
Electricity Metering Front-End
The ATSAMD20J15A-MN acts as a metering front-end MCU, sampling current and voltage via its 12-bit ADC and computing RMS, active, and reactive power. With 32 KB Flash and 4 KB SRAM, it fits single-phase residential meter firmware including a calibration table and a simple DLMS/COSEM or Modbus stack. The 1.6-3.6V supply accommodates direct operation from a regulated auxiliary rail off the meter's mains supply. Its low-power Standby mode (<1uA typical) is essential for class-1 metrology accuracy during brownout and outage events.
推荐
USB Human-Interface Devices
Although the SAM D20 lacks native USB, the ATSAMD20J15A-MN can pair with an external USB-to-UART bridge such as the MCP2200 to implement USB HID class devices such as custom keypads, mice, or HID-input industrial controls. The 32 KB Flash holds HID report descriptors, scan matrices, and a small command parser, while the SERCOM peripherals handle UART/SPI/I2C. Operating up to 48 MHz gives low-latency HID reporting; the 64-VFQFN exposes enough GPIO for 8x8 key matrices and rotary-encoder inputs without external expanders.
推荐
Battery-Powered IoT Sensor Nodes
The ATSAMD20J15A-MN excels in battery-powered IoT nodes because its Cortex-M0+ core achieves high performance at low MHz and its Sleep modes draw less than 1 uA with RTC running. The 1.6 V minimum supply enables direct operation from a single AA or coin-cell battery for years of service life. The 32 KB Flash fits LoRaWAN or BLE firmware stacks when paired with an external radio module; the 4 KB SRAM is adequate for sensor data buffers and a small RTOS. Operating up to +105C, it also suits outdoor enclosure deployments.
推荐
Consumer Appliance Control Boards
In washing machines, dishwashers, and small kitchen appliances, the ATSAMD20J15A-MN acts as the main user-interface and motor-control MCU. Its 12-bit ADC reads water-level and temperature sensors, while 16-bit timers generate PWM for solenoid and motor drivers. The 32 KB Flash holds user-interface state machines, fault diagnostics, and a small safety monitor; the 4 KB SRAM supports UI display buffers. The -40C to +105C temperature range handles the thermal envelope of consumer equipment. The 64-VFQFN package fits compact control PCAs.
推荐
推荐产品汇总
工程参考数据： ATSAMD20J15A-MN ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | ATSAMD20J15A-MNT | ATSAMD20J15A-CU | ATSAMD20J15A-ANT | ATSAMD20J15A-AUT | ATSAMD20J15A-CNT | ATSAMD20J14B-MU |
|---|---|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 64-VFQFN (9x9 mm) | 64-VFQFN (9x9 mm) | 64-TQFP | 64-VFQFN (9x9 mm) | 64-VFQFN (9x9 mm) | 64-TQFP | 64-VFQFN (9x9 mm) |
| Core | ARM Cortex-M0+ | ARM Cortex-M0+ | ARM Cortex-M0+ | ARM Cortex-M0+ | ARM Cortex-M0+ | ARM Cortex-M0+ | ARM Cortex-M0+ |
| Maximum Clock | 48 MHz | 48 MHz | 48 MHz | 48 MHz | 48 MHz | 48 MHz | 48 MHz |
| Flash Memory | 32 KB | 32 KB | 32 KB | 32 KB | 32 KB | 32 KB | 16 KB |
| SRAM | 4 KB | 4 KB | 4 KB | 4 KB | 4 KB | 4 KB | 4 KB |
| Operating Voltage | 1.6 V to 3.6 V | 1.6 V to 3.6 V | 1.6 V to 3.6 V | 1.6 V to 3.6 V | 1.6 V to 3.6 V | 1.6 V to 3.6 V | 1.6 V to 3.6 V |
| Temperature Grade | -40C to +105C (Industrial) | -40C to +105C | -40C to +85C | -40C to +125C (Automotive) | -40C to +125C (Automotive) | -40C to +85C | -40C to +85C |
关键差异点
- Wide operating voltage down to 1.6 V （对比 PIC16F677-I/SS)
- Higher CPU performance at the same MHz （对比 PIC16F684-I/ML)
- Larger memory headroom in same 64-VFQFN （对比 ATSAMD20J14B-MU)
设计说明
The 64-VFQFN exposed pad MUST be soldered to the PCB ground plane through a pattern of thermal vias (typically 0.3 mm drill, 0.6 mm pitch, 9 vias minimum) to provide both thermal dissipation and a low-inductance ground reference. Without the EP connected, the device may exhibit unstable operation and thermal shutdown at lower-than-expected loads. Reserve at least 16 sq mm of continuous copper under the package.
Place one 100 nF decoupling capacitor as close as possible to each VDD pin pair, plus a bulk 4.7 uF capacitor near the package. The SAM D20 hardware checklist requires decoupling within 2 mm trace length. For battery-powered designs, route the 32 kHz crystal oscillator traces in a guard-ring and use short, balanced traces to minimize load-capacitance mismatch.
Do not migrate firmware from a SAM D21 (Cortex-M0+ with USB) to the SAM D20 expecting USB support - the SAM D20 family has no USB peripheral. Also note the SAM D20 G-series (48-pin QFN) and J-series (64-pin VFQFN) have different SERCOM instance counts and I/O counts; pin-mapping spreadsheets must be regenerated when moving across the G/J boundary.
合规信息
RoHS and REACH compliant per Microchip product page; standard -MN variant is industrial grade. For AEC-Q100 qualified automotive temperature grade, choose ATSAMD20J15A-ANT or ATSAMD20J15A-AUT.
